Chiayo Live-100 series User manual

UHF 2-Way Synchronising True Diversity / Diversity Wireless Microphone System
ISO 9001
ISO 14001
OHSAS 18001
GREEN PRODUCT
Operation Manual
IS O
1 4 0 0 1
R E G I S T E R E D
O H S A S
1 8 0 0 1
R E G I S T E R E D

-1-
Thank you for choosing this wireless microphone system!
Our products are designed to last and for user-friendly operation. Each system consists of:
1. A receiver
2. A handheld or beltpack transmitter
3. A pair of antennas
4. A switching adaptor
5. An operation manual
For more details, please take a few moments to read this operating manual to gain a
thorough understanding of the function and operation of both transmitter and receiver.
Parts and functions of SDR-6200 IrDA/SDR-6100 IrDA receiver
Front panel
1. Power switch
2. IR sensor area
3. Diversity indicator
4. Audio signal indicator
5. LCD display
6. UP button
7. DOWN button
8. IrDA synchronisation button
9. SET button
Rear panel
SDR-6200 IrDA
SDR-6100 IrDA
POWER
D I V E R S I T Y
A B
A U D IO SDR-61 00 IrDA UHF 2-WAY SYNC. DIVERSITY RECEIVER
12
3 4
5
6
7
8
9
10 11 12 13
14
L IN E O U T
UN BA LA NC EDB A L A N C E D
D C I N
D C I N
12V
12V
A N T.AA N T.B
1 .G N D
2.
3.
M IC O U T
10
11
12 13 14

-2-
10. Antenna B socket (TNC)
11. Balanced audio output
12. Unbalanced audio output
13. Antenna A socket (TNC)
14. DC in
Changing CHANNEL / FREQUENCY
First, press "SET" till the display shows .
Then press UP or DOWN to select a new channel. As the channel changes, the
frequency changes accordingly, too. After the setting is made, the data will be
automatically saved.
CHANNEL scanning
For an interference-free operation, a cleaner channel might be necessary if the current
one receives too much interference. Before scanning, the transmitter must be switched off.
First, press "SET" till the display shows .
Then press UP or DOWN to go to the next clean channel.
After the setting is made, the data will be automatically saved.
CHANNEL SYNCHRONISING of the receiver and microphone
a. Limit the distance between the receiver and transmitter within 30cm.
b. Align both infrared areas
c. To change the receiver’s channel, please press the synchronising button of the microphone.
The microphone's LED will grow to imply synchronising signal transmitted and
will appear on the receiver's LCD, which means the receiver has been
successfully synchronised.
d. To change the microphones channel, please press the SYNC button of the receiver and
will appear on the receiver’s display, followed by
indicating data transferred.

-3-
Adjusting VOLUME level
The setting can be made right on the main menu .
Press UP or DOWN to choose a new level. After the setting is made, the data will be
automatically saved.
Adjusting SQUELCH level
First, press "SET" till the display shows .
Then press UP or DOWN to choose a new level. After the setting is made, the data will be
automatically saved.
Receiver installation
For best operation, the receiver should be at least 1m above the
ground and 1m away from a wall or metal surface to minimise
reflections. The transmitter should also be at least 1m away from
a wall or metal surface to minimise reflections. The transmitter
should also be at least 1m away from the receiver. Keep
antennas away from noise source such as motors, automobiles,
neon light as well as large metal objects.
Audio output connection
There are two audio outputs on the back of the receiver, Mic-level balanced and Line-
level unbalanced. Use shielded audio cable for the connection between the receiver and
the amplifier/mixer. If the amplifier/mixer has a 1/4"(6.3mm) phone jack, connect a cable
from the 1/4"(6.3mm) unbalanced audio output from the receiver to the amplifier/mixer. If
the amplifier/mixer has an XLR input, connect a cable from the balanced XLR audio
output from the receiver to the amplifier/mixer input.
Rack mounting
The receiver can be cabinet-mounted by either one or two units. If only one receiver is to
be mounted, an optional kit is available and it's installed as shown in Fig 1. If two
receivers are to be mounted, they can be assembled by another kit and installed as
shown in Fig 2.
(Fig 1)
(Fig 2)

-4-
UHF handheld microphones（SQ-6100 IrDA/SQ-2100 IrDA/SQ-1100 IrDA）
SQ-6100 IrDA
SQ-2100 IrDA
SQ-1100 IrDA
Parts and functions
SQ-6100 IrDA
SQ-2100 IrDA
SQ-1100 IrDA
Cartridge
1
1
1
Battery power LED
2
2
2
Power switch
3
3
3
LCD
4
-
-
Menu button
5
-
-
Setting button
6
-
-
IrDA synchronising button
7
4
4
Battery compartment
8
5
5
Color cap
9
6
-
IrDA sensor area
10
7
6
Charging port
-
-
7
Battery installation & indicator
This microphone requires 2 x AA batteries to operate.
To install, remove the battery cover and slide the batteries into the battery compartment &
replace the battery cover.
Note: Batteries contain a corrosive acid that may leak and damage the microphone when
stored for a long period. Batteries should be removed from the microphone before storing
without use for more than 4 weeks.
When the microphone is switched ON a red LED (2) will blink once to indicate the batteries
installed are in good condition. If the LED remains illuminated the batteries have expired
and require replacement.
1 2 3 7 4 5
6

-5-
Channel synchronising of the receiver and microphone
1. Limit the distance between the receiver and transmitter within 30cm.
2. Align both sensor areas
3. To change the receiver’s channel, please press the synchronising button of the microphone.
The microphone's LED will grow to imply synchronising signal transmitted to the receiver
and change its channel.
4. To change the microphone’s channel, please press the synchronising button of the receiver.
The receiver will transmit synchronising signal to the microphone and change its channel.
Other settings（SQ-6100 IrDA）
1. Channel setting
Use SET button to go to the CHANNEL/ FREQUENCY page.︰
After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made.
Pressing SET/MENU buttons will increase/decrease the channel number. The corresponding
frequency will change accordingly. 3 seconds after selecting a channel, it will be automatically
saved.
2. Battery type setting
Use SET button to go to the BATTERY TYPE page.︰
After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made.
Press SET button to select either NiMH (rechargeable battery) or AKLN (alkaline battery). 3
seconds after selecting a channel, it will be automatically saved.
Remark: NiMH battery must be selected when rechargeable battery is being used. Never select
AKLN (alkaline) when microphone is intended for charging, as alkaline battery isn’t
rechargeable. Wrong battery selection will result in battery sensing electronics to display wrong
and misleading status information.

-6-
UHF belt-pack transmitters（SM-7100 IrDA/SM-6100 IrDA/SM-1100 IrDA）
SM-7100 IrDA/SM-6100 IrDA SM-1100 IrDA
Parts and functions
SM-7100 IrDA
SM-6100 IrDA
SM-1100 IrDA
Antenna
1
1
1
LCD
2
2
-
Cover release button
3
3
6
Power switch
4
11
3
IrDA synchronising button
5
5
7
Menu button
6
6
-
Setting button
7
7
-
High-impedance gain control (GT)
8
8
8
Low-impedance gain control (MT)
9
9
9
Battery compartment
10
10
10
Audio mute switch
11
-
-
Battery power LED
12
12
2
IrDA sensor area
13
13
4
Mini XLR connector
14
14
5
Charging contacts
15
15
11
1
2
3 3
9
7
84 5
6
10
11 12
13
14
15
1
23
4
5
6
7
8
10
11 11
9

-7-
Battery installation & indicator
This belt-pack requires 2 x AA batteries to operate.
To install, open the battery cover using the cover release buttons and insert the batteries into
the battery compartment.
Note: Batteries contain a corrosive acid that may leak and damage the belt-pack when stored
for a long period. Batteries should be removed from the belt-pack before storing without use for
more than 4 weeks.
When the microphone is switched ON, the battery power LED (red) will blink once to indicate
the batteries installed are in good condition. If the LED remains illuminated the batteries
have expired and require replacement.
Channel synchronising of the receiver and transmitter
1. Limit the distance between the receiver and transmitter within 30cm.
2. Align both sensor areas
3. To change the receiver’s channel, please press the synchronising button of the transmitter.
The transmitter's LED will grow to imply synchronising signal transmitted to the receiver and
change its channel.
4. To change the transmitter’s channel, please press the synchronising button of the receiver.
The receiver will transmit synchronising signal to the transmitter and change its channel.
GAIN setting (GT/MT)
Gain control enables the user to set different output levels. GT is for the use of instrument with
high impedance, such as guitar while MT is for the use of low impedance such as lapel or
headset microphones.
Other settings（SM-7100 IrDA/SM-6100 IrDA）
1. Channel setting
Use SET button to go to the CHANNEL/ FREQUENCY page.︰
After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made.
Pressing SET/MENU buttons will increase/decrease the channel number. The corresponding
frequency will change accordingly. 3 seconds after selecting a channel, it will be automatically
saved.

-8-
2. Battery type setting
Use SET button to go to the BATTERY TYPE page.︰
After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made.
Press SET button to select either NiMH (rechargeable battery) or AKLN (alkaline battery). 3
seconds after selecting a channel, it will be automatically saved.
Remark: NiMH battery must be selected when rechargeable battery is being used. Never select
AKLN (alkaline) when transmitter is intended for charging, as alkaline battery isn’t
rechargeable. Wrong battery selection will result in battery sensing electronics to display wrong
and misleading status information.

-9-