SeeEyes SC-IPT3001E User manual

Release Version 1.0
8-channel EoC transmitter/receiver with Built-in Switch HUB
SC-IPC1208EH
User Manual
SC-IPT3001E
SC-IPR1208EH

Release Version 1.0
1
Precaution and Safety Guidelines
The content of this guideline is intended to protect user safety and prevent property damage.
Please read these operating instructions carefully and use the device properly.
Warning (If you do not keep any of the below guidelines, you may get
seriously injured or cause somebody’s death.)
■Be sure to install the product after unplugging power cord. Also, do not use many power
plugs at the same time.
- It may cause abnormal heat, fire and electric shock.
■Do not leave the device in a place where water will fall or splash. Also, do not place anything
with water on it, such as a vase of flowers.
- A malfunction or fire may result if liquid gets inside the device
■Do not bend the power cord by excessive force. Make sure the power cord is not crushed by
heavy things.
- It may cause fire.
■Do not open the lid arbitrarily as this device has high voltage part inside. Never disassemble,
repair or modify it.
- Abnormal work could result in fire, electric shock, and injury.
■Do not install this product in places with high humidity, dust, or soot.
- It may cause electric shock and fire.
■Do not tug at the power cord section or unplug the power plug with wet hands. If the power
cord is loose, do not plug in.
- There may be a risk of fire and electric shock.
■Always keep the location clean and dust-free during or after installing the device. When
cleaning the device, be sure to wipe it with a dry towel and do not use water, thinner, or organic
solvents.
- It may cause malfunction or fire
■Keep the device in a cool place where doesn’t let direct sunlight. Keep it at a proper
temperature and avoid heating appliances like candle or heater. Also, keep the equipment or
tools away from places where people come and go.
- There is a risk of damage to the surface of the device and a risk of failure, electric shock or fire.
■Pay attention to possible hazards in the workplace, such as wet floor, ungrounded power
extension cables, old power cords and a lack of safety earth. Consult your place of purchase or
professional if problems arise.
- It may cause fire and electric shock.
■Keep the back of the product more than 15 cm and the sides more than 5 cm from the wall.
Installing the product too close to the wall may bend, compress too much, or break the cable as
various external input / output connectors such as power cords protrude from the back of the
product.
- It may cause fire, electric shock and personal injury.

Release Version 1.0
2
■Concerning the input voltage for operating this device, a voltage range must be within 10%
of rated voltage. Also, do not use a heat source such as a hair dryer, iron and refrigerator to the
same power unit.
- It may cause abnormal heat, fire and electric shock.
■When thunder or lightning strikes, please pay attention to the safety and unplug the power
cord.
Caution (Failure to follow any of the following guidelines could result in
personal injury or property damage.)
■Avoid installing near strong magnetic fields or radio waves and wireless devices such as
radio or TV.
- Install in a place that is free from magnetic, radio, or excessive vibration.
■Proper ambient temperature and humidity are recommended.
- Avoid extremely high temperatures (above 50°C) or low (below -10°C), and humid conditions.
■Do not place heavy items on the product or let foreign substances enter inside the device.
- It may cause failure.
■Install the device in a well-ventilated place and avoid direct sunlight or heating devices.
■Install in a flat and stable place. Do not use an upright or inclined position.
- It may not work properly or it may be dangerous due to the device falling.
■Strong shock or vibration may cause device failure. Be careful when using the device.
- Install the device in a location free from strong vibration.
■If you notice any unusual noise or smell, unplug the power supply immediately and contact
the place of purchase or service center.
- There may be a risk of fire and electric shock.
■Rotate the air properly in the system operating room and secure the cover of the main body.
- It may be the cause of failure by environmental factors.
■Contact the service center and have them checked regularly to keep the system working.
- We are not responsible for any damage caused by carelessness of the user.
■Make sure the power cord is plugged into a grounded electrical outlet.
- There is a risk of electrical shock and personal injury.
■Place the power plug in a location that is easy to operate.
- If a product fault has occurred, the power plug must be pulled out in order to switch off the
device completely. The power switch on the main housing does not completely cut off the power
supply.
■When this device is used near devices that generate strong radio waves, such as Radio
devices (TRANCEIVER, walkie-talkie, etc.), repeaters, etc. this can affect the video signal and
abnormalities such as noise or cracks appear on the device. Do not use it, as this may cause the
device to malfunction.
■Please be careful not to change the cable connection.

Release Version 1.0
3
■When installing the product on a rack, be sure to install it separately from the equipment
installed above and below.
-If there is no space for heat to be released between the products, equipment failure may occur due to heat
saturation.
-The life of the product may be shortened due to an increase in the internal temperature of the product.
■UTP(Unshielded Twisted Pair) Cable is for indoor use only. Use a STP(Shield Twisted Pair)
Cable which is shielded for outdoor use.
■Transmission distance may vary depending on the type of coaxial cable.
■Refer to this user guide for any issues and enquiries. If you need professional assistance,
please contact the place of purchase or our service center.
■Class A equipment (commercial broadcasting and communication equipment)
-This device is a business grade electromagnetic wave device (Class A). The seller or user is advised to take
note of this, and the device is not intended for household use
■Insulate the part where the cable connects to the connector so that the metal part is not
exposed.
1. Introduction
1-1. Overview
This product consists of the SC-IPT3001E (transmitter), a 1-channel PoC-IP transmission device, and
an 8-channel receiver for EoC (Ethernet over Coax.) with an integrated switch HUB function.
Existing coaxial cables can be used to carry power to the transmitter and IP camera over a coaxial
cable while receiving signals from the IP camera and transmitting multi-channel IP camera data to an
NVR port, resulting in shorter construction times and lower construction costs.
It is able to transmit network data up to 1,800 m over the RG06, which compensates for the short
transmission distance of Ethernet devices with existing UTP cables.
1-2. Features
•8-channel Ethernet over coax with integrated switching HUB function
•Supply the IP camera with power (PoE type B / max. 12W @ Channel)
•Transmission of power and Ethernet data over RG-6 coaxial cables up to 1,800 m
•Autodiagnostic function for stable power supply
•Providing camera video data from multiple channels to the NVR via one RJ-45 port
•HUB does not have to be installed separately outdoors
•Cost-effective solution by using existing coaxial cable lines
•Lower installation costs and construction time as no power lines have to be laid

Release Version 1.0
4
2. Components
SC-IPR1208EH(Rx)
Power cord
User guide
Brackets & Screws
SC-IPT3001E(Tx) x 8
RJ-45 CABLE
Mounting brackets
3. Product Parts & Functions
3-1. SC- IPR1208EH (Receiver)
①COAX. LINK From TRANSMITTER : SC-IPT3001E connection port (BNC 8 Ports).
②Program update port (for manufacturer only): Port for product update.
③NVR SIDE : Port for connecting NVR or Network device(RJ-45 1Port).
④Ground Port : Provided for when earth grounding is required.
⑤AC INLET : AC power input port.
⑥Status LED : Display Link and Act. of each channel.
Name
Status
Description
T-LINK
ON
Power input of each channel ON / pairing completed
Blink
Pairing of each channel is in progress
OFF
No power input to any channel
C-ACT
Blink
Successful connection and operational status of the
transmitters for each channel
OFF
No connection with the transmitters of any channel
E-ACT
Blink
Ethernet Port of each channel is normal
OFF
Ethernet Port of each channel is NOT normal
ETHERNET
Blink
Connected to NVR and NETWORK device
①
②
③
④
⑤
⑥
⑦

Release Version 1.0
5
STATUS
OFF
NOT connected to NVR and NETWORK device
⑦Pairing Button : If any channel is not Paired automatically, press the button for more than 3
seconds to perform the Pairing for non-paired channel only.
3-2. SC- IPR1208EHC (RS-485 Receiver - Option)
3-3. PROTOCOL and BAUD RATE Setting
Move switch #1~4 as ON↔OFF to set PROTOCOL.
Move switch #5~8 as ON↔OFF to set BAUD RATE.
3-4. SYSTEM ID Setting
Set device number when controlling by RS-485.
Move DIP switch #1~8 as ON↔OFF to set ID value.
3-5. Communication Setting
- Data Length: 8 Bit, Start/Stop Bit: 1Bit, Parity Bit: None, Baud Rate: Menu set value
- Control communication data format
Byte
Value
Function
1
0xA0
STX (Data Start)
2
0x08
Device Code: product identification code
3
0x00~ 0xFF
DIP Switch Address (Device ID)
4
0x01~0x08
Channel(1CH: 0x01~8CH: 0x08)
5
0x00, 0x01
0x00: Power Off, 0x01: Power On
6
Check Sum
Check Sum = Below the sum of Byte2 + Byte3 + Byte4 + Byte5
①PROTOCOL / BAUD RATE Switch:
Set PROTOCOL and BAUD RATE when
using remote control
②SYSTEM ID Switch: Set device ID
when RS-485 controlling.
③RS-485 Port: RS-485 control terminal
port for remote control.
PROTOCOL Switch
BAUD RATE Switch
Control Protocol
#1
#2
#3
#4
#5
#6
#7
#8
Data Rate
SeeEyes
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
9600bps
-
-
-
-
-
ON
OFF
OFF
OFF
2400bps
-
-
-
-
-
OFF
ON
OFF
OFF
4800bps
-
-
-
-
-
ON
ON
OFF
OFF
19200bps
①
②
③

Release Version 1.0
6
3-6. Control Data Code
Function
Byte1
Byte2
Byte3
Byte4
Byte5
Byte6
Packet Example (Hex)
1CH OFF
A0
08
00
01
00
09
0xA0 0x08 0x00 0x01 0x00 0x09
1CH ON
A0
08
00
01
01
0A
0xA0 0x08 0x00 0x01 0x01 0x0A
2CH OFF
A0
08
00
02
00
0A
0xA0 0x08 0x00 0x02 0x00 0x0A
2CH ON
A0
08
00
02
01
0B
0xA0 0x08 0x00 0x02 0x01 0x0B
~
8CH OFF
A0
08
00
08
00
10
0xA0 0x08 0x00 0x08 0x00 0x10
8CH ON
A0
08
00
08
01
11
0xA0 0x08 0x00 0x08 0x01 0x11
All CH OFF
A0
08
00
09
00
11
0xA0 0x08 0x00 0x09 0x00 0x11
All CH ON
A0
08
00
09
01
12
0xA0 0x08 0x00 0x09 0x01 0x12
3-7. SC-IPT3001E (Transmitter)
①CAMERA PoE: Switch to set PoE IP camera power supply
※When connecting a PoE IP camera, set the CAMERA PoE switch to ON..
※The factory setting for the PoE switch is ON.
※When connecting a non-PoE camera, set the CAMERA PoE switch to OFF
②LED Indicator
Name
Color
Status
Description
PWR
Red
ON
Power On / Pairing completed
Blink
Under pairing
OFF
Power Off
ETH
Green
Blink
Ethernet connected
OFF
Ethernet not connected
①
③
④
②

Release Version 1.0
7
LINK
Green
Blink
Connected with Receiver
OFF
Not connected with Receiver
PoE
Red
ON
Supplying PoE to IP camera
Blink
IP camera overcurrent
OFF
Not supplying PoE to IP camera
③RECEIVER SIDE: Port to connect receiver and output video
④CAMERA SIDE: IP camera connection port
※Caution
Make sure to connect only to the exclusive product since power is supplied with data by BNC.
If not, it may cause damage to the product.
4. CABLE PIN Diagram
Number
Color
Color
Function
1
Orange + White
White
Orange
TX+
2
Orange
Orange
TX-
3
Green + White
White
Green
RX+
4
Blue
Blue
PWR+
5
Blue + White
White
Blue
PWR+
6
Green
Green
RX-
7
Brown + White
White
Brown
PWR-
8
Brown
Brown
PWR-

Release Version 1.0
8
5. Connection Diagram
6. Transmission Distance by Coaxial Cable Types (Loop resistance : Coax. cable)
Power
Loop Resistance
by PoE
ECX 5C-2V
(High)
ECX 5C-2V
(Mid.)
RG-6
(High)
RG-6
(Mid.)
RG-6
(Low)
3.0W
70.0 Ω
1,650m
930m
1,680m
930m
400m
6.0W
48.0 Ω
1,130m
640m
1,150m
640m
270m
9.0W
36.0 Ω
840m
480m
860m
480m
200m
12.0W
30.0 Ω
700m
400m
720m
400m
170m
※The transmission distance may vary depending on the construction quality of the coaxial cable
and connector.
※The transmission distance may vary depending on the specification of the camera and NVR.
※When using the PoE function of the transmitter, the transmission distance may vary depending
on the camera type. In particular, use exclusive adapters for cameras with high power consumption
such as IP PTZ cameras and cameras with many IR LEDs.
In addition, it is recommended that the length of the NETWORK CABLE between the camera and
the transmitter is no more than 1m. ※ If the receiver is supplied with power via a PoE hub, a length
of the NETWORK CABLE within 1m is recommended.
※If you are using the power adapter for the camera, turn the PoE switch on the transmitter OFF.
※The use of a LAN cable extension (coupler) leads to signal attenuation. It is not recommended to
use multiple extension genders.
Max. 1800m / RG-6

Release Version 1.0
9
7. Specifications
Model No.
SC-IPT3001E
Power Output
PoE Type B Supported
Max. Transmission
Distance (RG-6)
1,800m
Max. Transmission
Bandwidth (RG-6)
200Mbps(Phy Rate) / 75Mbps(TCP Rate)
PoE Max. Transmission
Distance (RG-6)
1,400m(8W)
Connection
Port
Rx Side
BNC-F, 75Ω
CAM Side
RJ-45 (TIA/EIA568B Type)
RJ-45 Connector Pin Details
1Pin: TX +, 2Pin: TX-, 3Pin: RX+, 4Pin: PWR+
5Pin: PWR+, 6Pin: RX-, 7Pin: PWR-, 8Pin: PWR-
PoE Switch
Slide switch : PoE On/Off Switch
Temperature / Humidity
-10°C ~ +45°C / 0 ~ 80%
Material / Weight
ABS / 60g
Dimensions
90(W) x 55(H) x 24(D)mm
Model No.
SC-IPR1208EH
Max. Transmission
Distance (RG-6)
1,800m
Max. Transmission
Bandwidth (RG-6)
200Mbps(Phy Rate) / 75Mbps(TCP Rate)
PoE Max. Transmission
Distance (RG-6)
1,400m(8W)
Power Input
AC 100 ~ 240V
Power Output
MAX.12W(@DC 48V) per Channel
Power Consumption
AC 100V, 50/60Hz, 2.0A, AC 240V, 50/60Hz, 1.0A
Connection
Port
NVR Port
RJ-45 x 1
CAM. Port
BNC x 8
RJ-45 Connector Pin Details
1Pin: TX +, 2Pin: TX-, 3Pin: RX+, 4Pin: PWR+
5Pin: PWR+, 6Pin: RX-, 7Pin: PWR-, 8Pin: PWR-
Transmission Bandwidth
10/100Mbps
Temperature / Humidity
-10°C ~ +45°C / 0 ~ 80%
Material / Weight
Steel / 3.9kg
Dimensions
430(W) x 44(H) x 350(D) mm

Release Version 1.0
10
8. Troubleshooting
Symptom
Identification Method
No power.
•Check the power cable connection status.
•Check the connection status of coaxial cable.
•Check the cable connection status of SC-IPT3001E.
•Check the CABLE PIN configuration status.
No video.
•Check the UTP CABLE PIN configuration status.
•Check the cable transmission distance.
•Check the grounded status.
•Check if the camera is compatible with NVR.
•Check if Pairing was done.
NETWORK
connection status
is not normal.
•Check if the NETWORK CABLE configuration is correct.
•Check if radio or any device that generates strong radio waves is
in the surroundings.
•Check if the network configuration is properly designed.
Video state
is not normal.
•Check the connection status of coaxial and network cable.
•Check if the camera is compatible with NVR.
•Check the camera performance status.

Release Version 1.0
11
9. Warranty Certificate
This product has passed thorough quality control and test, and if this gets broken during
normal use, we provide the two-year warranty service.
Model No.
Serial No.
Distributor
Date you purchased
Place you purchased
Warranty Period
Two (2) year from the date of purchase
Purchaser
Name
Address
•Please check this warranty indication first.
•Please contact your distributor after checking out any defect in the products.
•The standard for repairing, replacement or reimbursement follows Customer.
•Warranty content any defect under normal use within the warranty service period we
give you free repair service according to the warranty certificate.
•We charge you with the fee of parts and service despite of free warranty service period.
Any breakage made without care such as:
- Breakdown due to natural disasters (lightning, fire, flood, tsunami, etc.)
- When disassembled or repaired by the user
- When connecting power other than rated power.
- When you want to reassemble for full system or replace parts within warranty
service period.
- When unauthorized person modified or made damage on the product trying
to repair it.
- Failure due to careless handling of the user
- When replacing consumables
- Lightning strike.
•Please note that we don’t support the breakage after warranty service period expired. If
the customer wants to get it repaired, we charge them with the fee.
•The specification is subject to change without prior notice for quality improvement.

Release Version 1.0
12
MEMO

Release Version 1.0
13
MEMO

Release Version 1.0
14
MEMO

Release Version 1.0
15
SeeEyes Co., Ltd
#503~509, 511~512, Sunil Technopia, 555 Dunchon-daero, Jungwon-gu,
Seongnam City, Gyeonggi Province, Korea (Zip Code: 13215)
TEL: [phone]/5833
FAX: [phone]
EMAIL: [e-mail]
http://www.sscctv.com/eng