Digitus DN-651160 User manual

Industrial 8 + 4-port L3
managed Gigabit Ethernet
(PoE) Switch
Quick Installation Guide
DN-651160, DN-651161

2
Table Content
1. Overview ..................................................... 3
2. Features....................................................... 3
3. Specification ................................................ 4
3.1 standard...................................................... 4
3.2 Interface...................................................... 5
3.3 Work environment...................................... 5
3.4 Switch ......................................................... 5
3.5 Power supply .............................................. 5
3.6 Mechanical characteristic........................... 6
3.7 Industrial standard...................................... 6
4. Package........................................................ 6
5. Switch Panel................................................. 7
6. LED Indicator................................................ 8
7. Installation Caution ...................................... 9
7.1 Installation precautions .............................. 9
7.2 Din rail installation.................................... 10
7.3 grounding.................................................. 10
7.4 Power Connection .................................... 10
8. Management system Login ..........................11

3
1. Overview
This is a L3 managed industrial PoE Ethernet switch
with 8 Port 10/100/1000Mbps RJ45 (PoE) +4 Port
1000/2500/10000Mbps SFP, support one console port.
The Ethernet switch adopts Layer 2 protocol required
by the industrial site to ensure the stability of the
communication network. This series of switches adopt
low power consumption and fanless design to ensure
no noise interference, while supporting -40~80°C
working temperature and good EMC electromagnetic
compatibility performance to ensure stable work in
harsh industrial environments, and to build fast for
industrial applications such as factory automation,
intelligent transportation, and video surveillance.
Stable network terminal access network provides a safe
and reliable solution.
2. Features
Data control: support 802.3X full-duplex flow
control, support network storm suppression
Redundant network: support STP/RSTP/MSTP,
support ERPS (self-healing time <20ms)
Multicast management: support IGMP Snooping
V1/V2/V3
Redundancy backup: supports the virtual route
redundancy protocol VRRP

4
VLAN: Support IEEE 802.1Q VLAN, effectively isolate
the broadcast domain
Link aggregation: support link static/dynamic
aggregation, providing perfect bandwidth utilization
QOS: Support COS\DSCP, 4 queues, support
WRR\SP scheduling mode
Security management: support ACL access control
list, support 802.1X
Management function: support WEB, CLI, SNMP
management methods
Monitoring and maintenance: support port
mirroring, interface status monitoring, log
management
Supports static routes. IPV6
Supports NTP clients. Support PTP（1588v2）
IP40 protection grade
3. Specification
3.1 standard
IEEE802.3i 10Base-T,IEEE802.3u 100Base-TX,
IEEE802.3ab 1000Base-T,IEEE802.3z 1000Base-X,IEEE
802.3ae 10GBase-X,IEEE802.3x Flow
Control,IEEE802.1d-Spanning Tree
Protocol,IEEE802.1w-Rapid Spanning Tree
Protocol,IEEE802.1q-VLAN , IEEE 802.3ad, IEEE802.1p-
Class of Service,IEEE802.1X-Port Based Network Access
Control,IEEE802.3af,IEEE802.3at etc.

5
3.2 Interface
DN-651160: 8 Port Gigabit RJ45 + 4port 10G SFP
DN-651161: 8 Port Gigabit RJ45 (PoE) +4 Port 10G SFP
3.3 Work environment
Working temperature: -40～80 °C
storage temperature: -40～85 °C
relative humidity: 5%～95% (no condensation)
3.4 Switch
Bandwidth (switch capacity): 1.2Tbps
Packet Buffer Memory: 32Mbit
Packet Forwarding Rate: 406Mpps
MAC Address Table: 32K
3.5 Power supply
Input voltage: DC12-48V (DN-651160)
Input voltage: DC48-57V (DN-651161)
(Two-way power redundancy backup)
Access terminal:
Block terminal, Support dual power redundancy
Support built-in over current 4.0A protection
Support reverse connection protection
Max Power consumption: 18W

6
3.6 Mechanical characteristic
IP40 aluminum housing
DIN rail installation
Natural colling, no fan
Weight: 0.8Kgs
Measurement: 175.6 x 135 x 45.5 mm
3.7 Industrial standard
FCC CFR47 Part 15, EN55032, Class A
IEC61000-4-2 (ESD): ±8kV (contact), ±12kV (air)
IEC61000-4-3 (RS): 10V/m (80~1000MHz)
IEC61000-4-4 (EFT): Power Port: ±2kV; Data Port: ±1kV
IEC61000-4-5 (Surge): Power Port: ±2kV/CM, ±1kV/DM;
Data Port: ±4kV/CM, ±2kV/DM
IEC61000-4-6 (CS): 3V (10 kHz-150 kHz);
10V (150 kHz-80MHz)
IEC61000-4-16 (Common mode conduction): 30V
(cont.), 300V (1s)
Frequency range：150kHz-80MHz
Impact: IEC 60068-2-27
Free Fall: IEC 60068-2-32
Vibration: IEC 60068-2-6
4. Package
Industrial switch 1pcs
User manual 1pcs
Block terminal 1pcs

7
5. Switch Panel
Side panel: P1 and P2 are the number of connecting
terminals, P+1 and P-1 are respectively to the positive
and negative poles to be connected; Earthing screw
used for earthing equipment.
Front panel: the yellow light on RJ45 port is the link
light. It is on, when the connection is established and
the transmission data is flashing. The green light on
RJ45 port is the POE light, which is only on when the
switch port supplies power to the downlink PD. Green
LED on is for system operation. The power indicator
“POW” shows whether the current device is received
power in normal.
There are also green LED for optical link status.

8
Switch size (mm) 175.6* 135*45.5
6. LED Indicator
LED Indicator
Status
Definition
Power
Red LED on
Power work in
normal
Red LED off
No power or
power in trouble
RJ45 LED
Yellow LED on
Ethernet work in
normal
Yellow LED
flashing
Link
communication
in normal
Green LED on
PoE feeding to PD
device in normal
Green LED off
No PoE work

9
RUN
Green LED
slowing
flashing
System run in
normal
Optical LED
Green LED on
Optical work in
normal
7. Installation Caution
7.1 Installation precautions
In order to avoid damage to equipment and personal
injury caused by improper use, please follow the
following precautions:
In order to avoid damage caused by falling of the
equipment, please put the equipment in a stable
environment.
When supplying power to the equipment, pay
attention to confirm the range of power supply
voltage, as well as the positive and negative poles
of the power supply, so as not to damage the
equipment by wrong operation.
In order to reduce the risk of electric shock, ensure
that the equipment is well grounded in the working
environment.
No matter when, please do not arbitrarily remove
the equipment shell.
When placing the switch, please avoid the area with
dust and strong electromagnetic interference

10
7.2 Din rail installation
The first step is to check the grounding
and stability of the guide rail: the guide
rail slot of the switch is clamped into
the guide rail; the second step: from
the center to both sides of the guide
rail positioning screws in order. Step 3:
Use screws to fix the mounting rail card
slot on the fixed guide groove at both
ends of the guide rail to ensure that the
guide rail and the switch are fixed on
the guide rail vertically and stably.
7.3 grounding
Fix the grounding wire to the
grounding screw above the switch,
and ensure good reliable
connection of the grounding
system.
7.4 Power Connection
Insert the power cord into the specified position of the
6-core terminal, and insert the terminal into the
standard power supply inlet (P+1 and P-1 input
corresponding to the first power supply P1, and P+2
and P-2 input corresponding to the second power
supply P2).