Sego Lily SL-FT-3-LCMNT User manual

>> assembly instructions
ITEM#HF24608BA
SL-FT-3-LCMNT
SL-FT-3-DCMNT
DANGER
WARNING
WARNING
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open ame.
3. If odor continues, keep away from
the appliance and immediately call
your gas supplier or re department.
Do not store or use gasoline or other
ammable vapors and liquids in the
vicinity of this or any other appliance.
An LP-cylinder not connected for use
shall not be stored in the vicinity of
this or any other appliance.
For outdoor use only.
WARNING
Improper installation, adjustment,
alteration, service or maintenance
can cause injury or property damage.
Read the owners manual thoroughly
before installing or servicing this
equipment. If the information in this
manual is not followed exactly, a
re or explosion may result causing
property damage, personal injury, or
loss of life.
CARBON MONOXIDE HAZARD
This appliance can produce carbon
monoxide which has no odor. Using it in an
enclosed space can kill you. Never use this
appliance in an enclosed space such as a
camper, tent, car or home.
DANGER
1

2
1.Use the carton as a working surface to prevent product damage during assembly.
2. Gather all tools prior to assembly.
Congratulations on your latest Sego Lily purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your outdoor
space in no time. Good Luck—though we’re confident you won’t need it.
before you begin
safety information
WARNING
Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so may result in a re explosion, injury or death.
•The installation of this unit must adhere to local codes or either the National Fuel Gas Code, ANSI Z223. 1/NFPA54, OR CAN/CGA-B149.1, National Gas and
Propane Installation Code.
•THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed area.
•This unit is to be used with propane gas only! (sold separately)
•Do not attach a remote gas supply to this unit.
•This unit is not intended for natural gas.
•Converting this unit to natural gas is dangerous and not recommended. The conversion of this unit will void the manufacturer warranty.
•Do not use any solid fuel or charcoal for this unit.
•When igniting this unit, stay away from the burner as the ame will light up and may cause injury.
•LP GAS WARNING: Do not use any more than 1/4in depth lava rocks/pumice stones/Lava Glass™ above the burner holes. Doing so will suffocate the ame.
•If the propane gas tank is leaking gas, you may hear, see, or smell a hiss. Do the following: 1. Disconnect the propane gas tank. 2. Do not attempt to x the
problem yourself. 3. Contact your gas supplier or re department for help.
•Applying too much propane may result in gas pooling and will not burn. Allow fresh air into the unit so that the remaining gas may escape.
•Do not use a ame to check for gas leaks.
•The max. inlet supply pressure: mex. Gas supply 11 in w.c. (2.74kPa)
•Use LP propane tanks with the following dimensions: diameter 12in, height 18in, capacity 20lbs.
•You must use a propane tank that has a collar to protect the gas valve.
•DO NOT ll tank over 80 percent full.
•The tank system must be set up for vapor withdrawal.
•Discontinue use if any part of the propane tank is damaged. Rust and dents may be hazardous and should be inspected by a gas supplier.
•Do not burn anything other than the provided materials for this re table.
•Keep away from the unit for the rst 20 minutes after igniting your unit for the rst time, as lava rocks/pumice stones/Lava Glass™could pop out and cause
injury. Should any rocks pop out, discard them.

3
safety information continued
•Always ensure that lava rocks/pumice stones/Lava Glass™ are completely dry before use. Failure to do so will cause them to crack or pop.
•Do not operate unit until all parts are fully assembled.
•Do not paint or color any part of this heating unit.
•Unit may be hot while in use, do not attempt to move it while in use.
•Never leave this heating unit unattended while in use.
•This unit is not intended for cooking.
•Keep any ammable items away and do not use any other replace cover for this unit.
•Keep a safe distance to avoid burning skin or clothing.
•Do not sit or rest hands or feet on this heating unit.
•Never place hands or ngers on upper portion of this unit while in use.
•Keep all electrical cords and fuel supply hose away from heated surfaces.
•Combustible material should not be within 72 in of the top of the unit, or within 48 in around the entire unit.
•If the ame goes out while burning, turn the gas valve off. Wait 5 minutes before repeating the initial lighting procedure. Once you have a ame started, hold
down the control knob for 1 minute.
•Do not add water into the unit.
•Do not use this appliance if any part has been under water. Immediately call a qualied service technician to inspect the appliance and replace any part of the
control system and any gas control which has been under water.
•Do not disconnect any part while unit is in use.
•Do not store a spare propane tank on or near this unit.
•If the heating unit is indoors, detach the propane tank and leave outdoors.
•Do not operate on a boat or vehicle. This unit must be used on a at surface and outdoors ONLY.
•Always remove protective cover before operating (if applicable).
•Do not set the protective cover over the unit until it is turned off and completely cooled down.
•Check for leaks after not using the unit for long periods of time.
•Children should never operate this unit. Children must be supervised while near this unit.
•Keep gas tank at least 5 ft away from unit when lit. (if external tank)
•The maximum gas supply pressure is 250psi.
•All installation and repair should be done by a qualied professional. This unit should be inspected annually and cleaned regularly.
•Inspect all elements of this heating unit before each use. If there is damage, the burner must be replaced.
•Keep the hose out from any pathways to eliminate any accidental damage. (if external tank)
•Be aware of the hazards of high temperatures and stay away from the unit to avoid any burns or injury.
•The gas supply tank should be constructed and marked with the specications for the LP gas tanks of the U.S. Department of Transportation or the National
Standard of Canada CAN/CSA-B339, LP gas tanks, spheres and tubes for Transportation of Dangerous Goods; and Commission.
•The LP gas tank must have a listed overlling prevention device and a QCCI or Type I, (CGA810) LP gas tank connection.
•This heating appliance should not be used on plastic or articial wood decks.
•Combustible material should not be within 72 inches of the top of the unit, or within 48 inches around the entire unit.
•Instructions to keep the appliance are clear and free from combustible materials, gasoline, and other ammable vapors and liquids.
•Do not use the heating unit without inspecting the hose. Prior to use if there are any signs of wear or abrasion you must replace the hose.
•For appliances complying with clauses 5.20.4 and 5.20.5, a diagram with dimensions showing the manufacturers recommended position of the appliance, its
supply cylinder and hose routing shall be included. At a minimum. the diagram should be in a WARNING format including a warning about tipping hazard.

4
safety information continued
•Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.
•Young children should be carefully supervised when they are in the area of the appliance.
•Clothing or other ammable materials should not be hung from appliance or placed on, in, or near the appliance.
•Any guard or other protective device removed for servicing the appliance shall be replaced prior to operating the appliance.
•Installation and repair should be done by a qualied service person. The appliance should be inspected before use and at least annually by a
qualied service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners, and
circulation air passageways of the appliance are kept clean.
NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned “OFF” before assembling. Do NOT attempt to
assemble without proper tools.
IF APPLICABLE:
•Allow heating item to cool completely before placing on lid.
•DO NOT use heating item while lid is installed. Always remove the lid while heating item is in use.
NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned “OFF” before assembling. Do NOT attempt
to assemble without proper tools.
Note: Combustible material should not be within 72 in of the top of the unit, or within 48 in around the entire unit.
Combustible materials could be and are not limited to any items that may catch re such as dry vegetation, wood,
branches, leaves, plants, buildings, structures, fabrics, clothing, sawdust, all chemicals, and all ammable liquids.

5
table of contents
introduction
parts list
assembly
operation
maintenance
troubleshooting
warranty & contact info
2
6
7
14
15
16
17

6
ITEM DESCRIPTION QUANTITY
A
B
C
D
E
F
G
H
I
J
K
1 pc
1 pc
1 pc
1 box
1 pc
1 pc
1 pc
1 pc
1 pc
4 pc
1 pc
cover
body
door panel
lava rocks
AAA battery (not included)
control knob (pre-assembled)
electronic Igniter (pre-assembled)
burner (pre-assembled)
guard (pre-assembled)
feet (pre-assembled)
glass
F
G
I
H
A
B
E
E
D
C
K

7
step 1.
1. Check that the control knob (F) for the gas supply
system is turned to the “OFF” position before starting
any assembly.
OFF
F

8
step 2.
1. Remove the door panel (C) from the body (B) of the
re column and put the 20 lb. propane gas tank (not
included) into the body (B). Turn the wing screw on the
outside of the internal tank holder clockwise to tighten
the tank into the holder.

9
step 3.
1. Turn the cylinder valve on the tank clockwise to close
the propane tank.
CYLINDER
VALVE

10
CYLINDER VALVE
BLACK COUPLING NUT
REGULATOR
turn clockwise to connect
step 4.
1. Attach the pre-assembled regulator from the body (B)
to the cylinder valve by turning the regulator coupling
nut clockwise. Make sure it is fastened securely and
tighten connections by hand only. Place door panel (C)
back on the body (B) of the re column.

11
step 5.
1. Remove the rubber cap on the electronic igniter (G) by
unscrewing and slide battery (E) into the battery slot.
Make sure the positive side of the battery faces
outward. Screw the electronic igniter cap (G) over the
battery tightly.
E
G
G

12
step 6.
To ensure proper function, the guard (I) on this burner (H)
should be free of lava rocks at all times.
DANGER
1. Pour the box of lava rocks (D) into the body (B) of the
rebowl.
D
BI

13
step 7.
1. Insert the glass (K) into the supports at the top of the
body (B). B
K

14
operation.
To Light
Leak Test
To Extinguish
Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor
area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off” position.
Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles occur on any
connection there may be a leak. If you smell gas or a leak is discovered turn the gas valve off,
disconnect propane gas tank and do not use the appliance until the leak is repaired.
Do not use the heating unit without inspecting the gas hose (if applicable). If there are signs of wear
or abrasion you must replace the hose. Pumice stones/lava rocks/Lava Glass™ could pop up and
strike somebody’s face during the process of lighting this unit; stand away from the unit for the rst 20
minutes after igniting.
Wait 5 minutes after extinguishing ame prior to placing a lid (if applicable) or protective cover on
heating item.
1. Make sure the control knob (F) is in the “off” position.
2. Remove the door panel (C) from the body (B) and slowly open the valve on the propane gas tank
by turning the knob counterclockwise.
3. Replace the door panel (C) on the body (B)
4. Push and hold the electronic igniter (G) to create sparks within the electrode, continue to hold.
5. Push in the control knob (F) and turn to the “low” position. Keep holding the control knob (F) to
allow gas to ow for 45 seconds.
6. If ignition does not occur within a few seconds release the control knob (F) and rotate to the “off”
position. Wait for 5 minutes for gas to clear and then repeat the above lighting instructions.
7. Once the product is lit, the ame intensity may be controlled by turning the control knob (F)
between the “low” and “high” positions.
1. Turn control knob (F) clockwise to the “low” position; let the knob pop up and continue turning the
control knob (F) to the “off” position.
2. Close the cylinder valve on the propane gas tank if you don’t intend to use it for a long time.

15
maintenance.
• Before performing any maintenance always disconnect propane gas tank.
• Keep the heating item free and clear from combustible materials.
•Visually inspect burner for obstructions and keep tank enclosure free and clear from debris.
• Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner and pumice stones/
lava rocks/Lava Glass™ are completely cooled down. Wipe down with a soft cloth.
• Harsh weather conditions may cause stubborn stains, discoloration and possibly rust pitting.
• Permanent damage may occur if powder or solvent comes in contact with painted or plastic
components on this heating unit.
• Keep the heating unit stored away from direct sunlight.
• If storing this unit inside, disconnect the propane gas tank from the gas valve.
• Not using manufacturer approved or supplied parts/accessories may result in a defective condition
and void the warranty of this heating unit.
• Always place lid (if applicable) or protective cover on heating item when not in use.
Envirostone™ Surface Care
Our Envirostone™ material has been sealed with a patented treatment to prevent staining and moisture
absorption, but it does require proper maintenance to ensure the integrity of the surface. Please see
below for recommendations on maintaining your Envirostone™ surface for years of pleasure:
• Clean any spills immediately to prevent permanent Envirostone™ surface staining or damage. Blot
any liquid spills with a clean, dry cloth to avoid spreading of the spill to the rest of the table. Clean your
Envirostone™ surface with a soft, clean cloth or sponge. Mix a solution of warm clean water and mild
dish soap to remove any surface dirt or mild spills. Rinse all soap solution off of the tabletop and dry
completely to avoid water spots. Regularly cleaning the Envirostone™ surface will aid in a longer lasting
product.
• Do not use petroleum-based or abrasive cleaning products. Do not use any harsh brushes when
cleaning the Envirostone™ surface.
• Do not slide products across the Envirostone™ surface to avoid permanent scratching and damage.
• Always use protective mats such as coasters or place mats when eating near an Envirostone™
surface. These protective products will help absorb sweating on cool beverages and will block out any
heat rings from appearing beneath a warm mug or plate. When placing hot dishes on an Envirostone™
surface, always use mats or hot pads.
• Envirostone™ surface must be covered at all times when not in use. Cover your product with an
outdoor furniture cover when not in use to protect it from the elements. Store your product indoors
during winter months. Avoiding extreme cold temperatures will prevent cracking of the tabletop.

16
troubleshooting.
Problem Cause Solution
Igniter pin and burner are wet Dry off with a soft cloth
Igniter battery is incorrectly inserted Check which direction the battery is
inserted
Igniter pin is broken Contact Bond Manufacturing for a
replacement part
Electrode wire is loose or disconnected Reconnect wire to the igniter box located
inside the table behind the igniter box
Electrode wire is shorting between valve
and igniter pin
Contact Bond Manufacturing for a re-
placement part
No gas flow Check that the gas tank isn’t empty
Regulator isn’t connected securely to the
tank
Tighten regulator connection to the gas
tank
Gas flow is obstructed Check all hoses for kinks and bends
Burner ports are clogged Turn all gas flow connections off. Insert
an opened paper clip (or similar item) into
each of the burner ports to clear them
out.
Flame is obstructed at burner ports Check that all burner ports are free of
any small lava rocks/pumice stones/Lava
Glass™ pieces
Regulator hose is kinked Straighten hose of all bends or kinks
No gas flow Check that the gas tank isn’t empty
Excess flow safety valve has been
activated
Turn the control knob to the ‘off’ posi-
tion. Close the tank valve and disconnect
propane gas tank. Turn the control knob
to ‘high’; wait 1 minute. Turn the control
knob back to the ‘off’ position. Recon-
nect propane gas tank. Light the fire unit
as indicated in the ‘To Light’ section of
this manual.
High or gusting winds Increase flame to ‘high’
No gas flow Check that the gas tank isn’t empty
Excess flow safety valve has been
activated
See ‘sudden drop in gas flow’ above
Heating unit won’t light
Burner won’t light
while using a match
Heating unit emits a lot
of black smoke
Sudden drop in gas
flow
Flame blows out easily

17
warranty.
The manufacturer warranty will be voided by, and manufacturer disclaims any responsibility for, the
following actions:
•Modication of the unit and/or components including the gas valve assembly.
•Use of any component part not manufactured or approved by Bond Manufacturing.
•Use and installation other than what is listed in this manual.
Please contact the manufacturer for replacement parts.