SEI Lynx-CustomFit LYNX2-LC User manual

Lynx‐CustomFit® Splice‐On Connector Ver.2
‐LYNX2‐LC for Optical Cord (2.4/3mm) with Duplex LC Clip‐
Installation Manual
Foryoursafetyoperation Precautions
ETK1123160
TheLynx‐CustomFit® Splice‐On Connectoris designedand
manufacturedtoassurepersonalsafety.Improperoperation
canresultinbodilyinjuryandseriousdamagetothisproduct.
Pleasereadandobserveallwarningsinstructionsgiveninthis
operationmanual.
Wearsafetyglassestoprotectyoureyeswhen
hdli ti l fib
!
1. Improperassemblywillresultinalossofperformance.
Pleasereadinstructions giveninthisoperationmanual
and the operation manual of the fusion splicer.
2. Never touch the fiber of the stub. It has been inspected
in the factory.
3. Theproductissensitivetodirtordust.Donottakeout
any
parts from the package
until it is to be used
h
an
dli
ngop
ti
ca
l

fib
er.
Neverlookintotheendofamicroscopeoroptical
cableconnectedtoanopticaloutputdevicethatis
operating.Laserradiationisinvisible,anddirect
exposurecanseverelyinjurethehumaneye.
Alcoholisflammable,causesirritationandisharmful
!
!
any
parts

from

the

package

until

it

is

to

be

used
.
4. Thecharacteristicwillbeinfluencedbythefiber
cleavedsurfacecondition.Pleaseuseacleaverwhich
hasagoodcleavingcharacteristic.
5. Donotremovethedustcapuntiltheconnectorhas
beencompletelyassembled inordernottocausean
highinsertionlossduetothem.
ifswallowedorinhaled.Keepalcoholawayfrom
heat,sparks,skin,andavoidcontactwitheyes.
Inthecaseoftheworkatthehighplace,pleasebe
carefulnottodropanassemblingtool.
!
!
Composition Assembling Tools
Di bl
Rear
Furcation
Bl
l
id
Di
sposa
bl
e
Holder(*1)
Front
Rear

Stopper Boot
Furcation

Tube Fiber Holder
LYNX2‐UML‐S
Cord Tool
LYNX2‐CORDTOOL
B
e
l
ow too
l
s are requ
i
re
d
.
FusionSplicer
T‐Q101‐CA, etc.
FiberCleaver
FC‐6S‐C, etc.
Jacketremover
JR‐M03, etc. KevlarCutter
Recommended Program
Splicer Fiber SplicingProgram HeaterProgram
Below equipments or tools are examples.
Front

Housing
Ferrule
Subassembly
ProtectionSleeve
and Spring
(*1) 1 pc / 100 connectors
SMF G 652 G657
T‐25eS SMF SM1: SMF1C Lynx
or FPS (60mm)
MMF MM1: MMF1C
T‐39FH SMF LYNX‐SM Lynx
or FPS (60mm)
MMF LYNX‐MM
T‐Q101‐CA
(T‐71C)
SMF Standard SMF Lynx
or 60mm 0.9
MMF MMF 50&62.5
PleaseperformArctestpriortothesplicingoperation.
(Seethe operation manual of the splicer.)
*Fiberfortestingisnotincludedinthekit.
HolderType Cleave length:
10mm
Copyright©2011SumitomoElectricIndustries,LTD.
SMF
:
G
.
652
,
G
.
657
MMF:MM50(OM2),MM50(OM3),MM50(OM4),MM62.5(OM1) Pleasecheckfibertypeinsidethefieldfiber.
North Carolina (USA)
SumitomoElectricLightwaveCorp.
78 Alexander Drive, P.O. Box 13445, RTP, NC 27709
TEL+1‐919‐541‐8100
http://www.sumitomoelectric.com/
Yokohama (Japan)
SumitomoElectricIndustries,Ltd.
(LightwaveNetworkProductsDivision)
1, Taya‐cho, Sakae‐ku, Yokohama 244‐8588, Japan
TEL+81‐45‐853‐7223, http://global‐sei.com/fttx/
London (UK)
SumitomoElectricEuropeLtd.
220 Centennial Avenue, Elstree, Herts. WD6 3SL, UK
TEL+44 (0)20‐8953‐8118
http://www.sumielectric.com/

LYNX2‐LCforOpticalCord (2.4/3mm)with Duplex LC Clip
Assembly Procedure
(A) Set Fusion Condition (B) Perform Arc Test
Then perform the arc test
according to the
instruction.
ETK1123160
(1) DisassembleRearParts. (3) Open Cord Tool and set the cord on the proper groove.
Rotate the cord, then remove the outer sheath.
Push “power
key” for more
than 1 sec.
“Main Menu”
Select Fiber Type Select “FiberType”, then “Return”. Select “Arc Test”
*Fiberfortestingisnot
includedinthekit.
Pleasecheckfibertype
insidethefieldfiber.
“Main Manu”
Select Sleeve Type
Select Sleeve Type
Then “Return”
Seetheoperationmanualofeachsplicer.ThesearetheexampleofT‐Q101‐CA(T‐71C).
(2) Slide Boot on Cord. (4) Mark at 100mm from the end
of Sheath.
Contact the top
to the wall
Rotate
the cord
Remove
the sheath
100 mm
(5)
Mark
on
900um
fiber
on
(6)
Set
Cord
on
Tool
with100mm
Mark
at
the
edge
of
(
7
)
Slide RearSto
pp
erand
Rear
Stopper Boot
(8)
Remove
the
fiber
coating
from
the
MarkHere
(5)
Mark
on
900um
fiber
on
Cord Tool.
Cord
900um
Fiber
Mark
(6)
Set
Cord
on
Tool
with100mm
Mark
at
the
edge
of
Cord Tool and pull. Then Outer Sheath is separated.
Pull the
cord
()
pp
Protection Sleeve onto the fiber.
Rear
Stopper
Protection
Sleeve
(8)
Remove
the
fiber
coating
from
the
marking point. (JR‐M03)
0.9to0.25mm
0.25to0.125mm
Markpoint
Clean
rubber
clampand
blade
regularly
2. Close
1. Place
(12) Cleave the fiber (FC‐6S)
cord
(9) Clean the fiber with
lint‐free cleaning wipe.
Moistened
(11) Set the sleeve on theholder.
Protection
Sleeve
Rear
Stopper
Do not touch
Confirmtheposition
Good
No Good
(10) Set the fiber on theholder.
Donottouch
barefiber
(13) Setfiberholderonthesplicer
(leftside). (15) Setstubholderonthesplicer
(rightside).
3. Slide
Moistened

withalcohol
Do

not

touch

barefiber
No Good
(14) Pick up the stub and set the stub on the plastic holder.
Push to
close
Placefiberon
V‐groovegently
Placefiberon
V‐groovegently
(16) Fusion Splice. (17) Open the stub and fiber holders.
Left side first
Then right side
(18) Pick up the spliced fiber.
Grasphereto
pick up
Donottouch
barefiber
Copyright©2011SumitomoElectricIndustries,LTD.
If the position of the fiber is wrong,
set the fiber or stub again.
Buttonto
startsplicing
Lightlyholdingassemblytopreventbending
Lightlymaintainingtensionto
preventbending

LYNX2‐LCforOpticalCord (2.4/3mm)with Duplex LC Clip
Assembly Procedure
Notwisting
(19) Slide Protection untilitcoverstheprojectionof
theflange.
ETK1123160
(20) Set Sleeve into the heater.
Then left side
(21) Confirm the position before
heating. Sleeveatcenter
fht
Buttonto
(22) Heat Protection Sleeve. (23) Pick up Sleeve.
Notwisting Notwisting
Lightlymaintaining
tensiononfiber
Right side first
Notwisting
(24) Slide Rear Stopper.
o
f

h
ea
t
er
Nogap
startheating
Lynxheaterprogram runsafanto
coolthesleeveafterheating
Becareful for hot sleeve,
spring and flange even after
the cooling by fan.
!
(26)
Slide Rear Parts.
(27)
Put
Rear
Stopper
in
Front
Housing.
Rear Stopper
(
25
)
Put Inner Housin
g
.
(26)
Slide

Rear

Parts.
Make sure
protrusion of cap
from Front Housing.
(27)
Put
Rear
Stopper
in
Front
Housing.
Front
Housing
Rear
Stopper
()
g
APC‐ Reddot
PC/UPC‐ Blackdot
Front Housing
Flange
Makesurethe
orientation
(28) Insert the split sheath into Jacket
Stopper and hold them on Rear Stopper.
Jacket
Stopper
Rear
Stopper
Aligneachtriangle.
(29) Hold the split sheath by Jacket Stopper. (30) HoldKevlaronRear Stopper,
then push Boot toward Rear Stopper.
Boot Rear
Stopper
(32) Secure Kevlar by Kevlar Stopper.
Rotateclockwise.
(31) Slide Kevlar Stopper to the end.
NeverTwistSheath
Neverrollupfiber Neverrollupfiber
(33) Trim Excess Kevlar by Kevlar Cutter andcutthetether.
Keep Fiber Straight
HoldKevlarTightly
Keep Fiber Straight, HoldKevlarTightly
Copyright©2011SumitomoElectricIndustries,LTD.
Complete