SEI Lynx-CustomFit LYNX2-MPO User manual

Copyright © 2011 Sumitomo Electric Industries, LTD.
Fusion Splicer
Type-Q101-M12
(T-71M12)
Fiber Cleaver
FC-6RM etc.
Jacket
remover
JR-6
Fiber Holder
FHM-12
(For 12c Fiber)
Fiber Holder
FHM-8
(For 8c Fiber)
SMF : G.652, G.657
MMF : MM50(OM2), MM50(OM3), MM50(OM4), MM62.5(OM1)
The Lynx-CustomFit® Splice-On Connector is designed and
manufactured to assure personal safety. Improper operation
can result in bodily injury and serious damage to this product.
Please read and observe all warnings instructions given in this
operation manual.
Wear safety glasses to protect your eyes when
handling optical fiber.
Never look into the end of a microscope or optical
cable connected to an optical output device that is
operating. Laser radiation is invisible, and direct
exposure can severely injure the human eye.
Alcohol is flammable, causes irritation and is harmful
if swallowed or inhaled. Keep alcohol away from
heat, sparks, skin, and avoid contact with eyes.
In the case of the work at the high place, please be
careful not to drop an assembling tool.
Lynx-CustomFit® Splice-On Connector Ver. 2
- LYNX2-MPO for Bare Ribbon Fiber -
Installation Manual
!
!
!
1. Improper assembly will result in a loss of performance.
Please read instructions given in this operation manual
and the operation manual of the fusion splicer.
2. Never touch the fiber of the stub. It has been inspected
in the factory.
3. The product is sensitive to dirt or dust. Do not take out
any parts from the package until it is to be used.
4. The characteristic will be influenced by the fiber
cleaved surface condition. Please use a cleaver which
has a good cleaving characteristic.
5. Do not remove the dust cap until the connector has
been completely assembled in order not to cause an
high insertion loss due to them.
For your safety operation
!
Precautions
Composition
Disposable
Holder (*1)
Dust Cap
Front
Housing
w/Spring
Rear
Stopper
MT STUB
Boot
Protection
Sleeve
(*1) 1 pc / 100 connectors
Assembling Tools
Recommended Program
Splicer Fiber Splicing Program Heater Program
Type-Q101-M12
(T-71M12)
SMF 12c SM12c
Lynx MPO
SMF 8c SM8c
MMF 12c MM12c
MMF 8c MM8c
Please perform Arc test prior to the splicing operation.
(See the operation manual of the splicer.)
*Ribbon fiber for testing is included in the connector kit.
Please check fiber type inside the field fiber.
ETK1123091C
Below equipments and tools are required.
Dummy Cap
w/ Tether
SM Low Loss SM Std. Loss MM62.5 OM1 MM50 OM2 MM5010GOM3
8 degree Polish Flat Polish
Yellow Green Beige Black Aqua
Polish Surface and Housing Color
Rear Parts
North Carolina (USA)
Sumitomo Electric Lightwave Corp.
78 Alexander Drive, P.O. Box 13445, RTP, NC 27709
TEL [phone]
http://www.sumitomoelectric.com/
Yokohama (Japan)
Sumitomo Electric Industries, Ltd.
(Lightwave Network Products Division)
1, Taya-cho, Sakae-ku, Yokohama 244-8588, Japan
TEL [phone], http://global-sei.com/fttx/
London (UK)
Sumitomo Electric Europe Ltd.
220 Centennial Avenue, Elstree, Herts. WD6 3SL, UK
TEL [phone]
http://www.sumielectric.com/

Copyright © 2011 Sumitomo Electric Industries, LTD.
LYNX2-MPO for Bare Ribbon Fiber
Assembly Procedure ETK1123091C
No twisting No gap
Button to
start heating
Lynx heater program runs a fan to
cool the sleeve after heating
Lightly maintaining
tension on fiber
Right side first Then left side
Left side first Then right side
Lightly maintaining tension to
prevent bending
Lightly maintaining tension to
prevent bending
Place fiber on
V-groove gently
UP
(1) Slide Rear Parts, Spring and Protection
Sleeve onto the ribbon fiber.
(2) Set ribbon fiber on Fiber holder.
(3) Remove Coating (JR-6)
1. Place
3. Slide
Clean rubber clamp
and blade regularly
(5) Cleave the fiber (FC-6M)
No gap
(6) Set fiber holder on the splicer
(left side).
Grasp here
Do not touch bare fiber
(7) Pick up MT STUB and set the stub on the plastic holder. (8) Set stub holder on the splicer
(right side).
(9) Fusion Splice.
(10) Slide the sleeve to
the holder.
(12) Pick up the spliced fiber.
No twisting
(13) Slide Protection Sleeve to
MT STUB.
(14) Set Sleeve into the heater. (15) Confirm the position before heating. (16) Heat Protection Sleeve.
(17) Remove Dummy Cap.
Window
(18) Put Front Housing.
2. Close
Complete
No twisting
Place fiber on
V-groove gently
See the operation manual of T-71M12.
Rear Parts
Spring
(Remove from
Front Parts)
Protection
Sleeve
CH1 (Blue Fiber)
Front Side
Stainless Steel
Bottom Side
Make sure the orientation
CH1 (Blue Fiber)
Front Side
25 to 30mm
(4) Fiber Cleaning.
Moistened
with alcohol
Push to
close
UP should be
upper side
(11) Open the cover of the holder.
Ridge
Align Window and Ridge
Rear Parts
Front Parts
Rear
Parts Spring
MT STUB Dummy CAP
(A) Set Fusion Condition
Push “power
key” for more
than 1 sec.
(B) Perform Arc Test
Arc Test “ON”.
Then perform the arc test
according to the instruction.
*Fiber for testing is included
in the kit.
Please check fiber type
inside the field fiber.
If the position of the fiber is
wrong, set the fiber or stub again.
Touch Start icon
Cap
“Main Menu”
Select Fiber Type Select “Fiber Type”, then “Return”. “Main Manu”
Select Sleeve Type
Select Sleeve Type
Then “Return”