SEI LYNX2-LC User manual

Copyright © 2011 Sumitomo Electric Industries, LTD.
SMF : G.652,G.657
MMF : MM50(OM2), MM50(OM3), MM50(OM4), MM62.5(OM1)
The Lynx-CustomFit® Splice-On Connector is designed and
manufactured to assure personal safety. Improper operation
can result in bodily injury and serious damage to this product.
Please read and observe allwarnings instructions given in this
operation manual.
Wear safety glasses to protectyour eyes when
handling optical fiber.
Never look into the end of a microscope or optical
cable connected to an optical outputdevice that is
operating. Laser radiation is invisible, and direct
exposure can severely injure the human eye.
Alcohol is flammable, causes irritation and is harmful
if swallowed or inhaled. Keep alcohol away from
heat, sparks, skin, and avoid contact with eyes.
In the case of the work atthe high place, please be
careful not to drop an assemblingtool.
Lynx-CustomFit® Splice-On Connector Ver. 2
- LYNX2-LC for 250um or 900um Tight Buffered Fiber -
Installation Manual
!
!
!
1. Improper assembly will result in a loss of performance.
Please read instructions given in this operation manual
and the operation manual of the fusion splicer.
2. Never touch the fiber of the stub. It has been inspected
in the factory.
3. The product is sensitive to dirt or dust. Do not take out
any parts from the package until it is to be used.
4. The characteristic will be influenced by the fiber
cleaved surface condition.Please use a cleaver which
has a good cleaving characteristic.
5. Do not remove the dust cap until the connector has
been completely assembled in order not to cause an
high insertion loss due to them.
For your safety operation
!
Precautions
Composition Assembling Tools
Fusion Splicer
T-Q101-CA(71C),etc. Fiber Cleaver
FC-6S-C, etc. Jacket remover JR-M03, etc.
Recommended Program
Splicer Fiber Splicing Program Heater Program
T-25eS SMF SM1:SMF1C Lynx
or FPS (60mm)
MMF MM1:MMF1C
T-39FH SMF LYNX-SM Lynx
or FPS (60mm)
MMF LYNX-MM
T-Q101-CA
(T-71C) SMF Standard SMF Lynx or 60mm 0.9
MMF MMF50&62.5
Please perform Arc test prior to the splicing operation.
(See the operation manual of the splicer.)
*Fiber for testing is not included in the kit.
Please check fiber type inside the field fiber.
ETK1123069C
Holder Type Cleave length: 10mm
Disposable
Holder (*1)
Front
Housing
Rear
Stopper
Ferrule
Subassembly
Boot
Furcation
Tube
Protection Sleeve
and Spring
(*1) 1 pc / 100connectors
Holder (Fiber Side)
for 900um tight buffer for 250um fiber
LYNX2-UML-S FHS-09 FHS-025 LYNX2-S-LB5
Below equipment or tool are examples.
Either one holder is required.
North Carolina (USA)
Sumitomo Electric Lightwave Corp.
78 Alexander Drive, P.O. Box 13445, RTP, NC 27709
TEL [phone]
http://www.sumitomoelectric.com/
Yokohama (Japan)
Sumitomo Electric Industries, Ltd.
(Lightwave Network Products Division)
1, Taya-cho, Sakae-ku, Yokohama 244-8588,Japan
TEL [phone], http://global-sei.com/fttx/
London (UK)
Sumitomo Electric Europe Ltd.
220 Centennial Avenue, Elstree, Herts. WD6 3SL, UK
TEL [phone]
http://www.sumielectric.com/

Copyright © 2011 Sumitomo Electric Industries, LTD.
LYNX2-LC for 250um or 900um Tight Buffer
Assembly Procedure ETK1123069C
(1) Slide Rear Parts onto the
fiber.
Insert fiber into
this hole
(2) Slide Protection Sleeve onto the
fiber. (3) Remove the fiber coating.
Approx. 35mm (JR-M03) 0.9 to 0.25mm
0.25 to 0.125mm (4) Clean the fiber with lint-
free cleaning wipe.
Moistened
with alcohol
(5) Set the fiber onthe holder. Confirm the position
Good
No Good
No Good
Do not touch
bare fiber 1. Place
3. Slide
Clean rubber clamp
and blade regularly
(6) Cleave the fiber (FC-6S)
No gap
(7) Set fiber holder on the splicer
(left side).
Grasp here to
pick up Do not touch
bare fiber
(8) Pick up the stub and set the stub on the plastic holder. (9) Set stub holder on the splicer
(right side).
Place fiber on
V-groove gently If the position of the fiber is wrong,
set the fiber or stub again.
(10) Fusion Splice.
Lightly holding assembly to prevent bending
(11) Open the stub and fiber holders.
Lightly maintaining tension to
prevent bending
(12) Pick up the spliced fiber.
No twisting
(13) Slide Protection until it covers the projection of
the flange.
(14) Set Sleeve into the heater.
No twisting
(15) Confirm the position before
heating. Sleeve at center
of heater
No gap
Button to
start heating
(16) Heat Protection Sleeve.
Lynx heater program runs a fan to
cool the sleeve after heating
(17) Pick up Sleeve.
Be careful for hot sleeve,
spring and flange even after
the cooling by fan.
!Cut Tether
2. Close
Push to
close
Lightly maintaining
tension on fiber
Complete
Right side first Then left side
No twisting
Left side first Then right side
Button to
start splicing
Place fiber on
V-groove gently
(A) Set Fusion Condition
Push “power
key”for more
than 1 sec.
“Main Menu”
Select Fiber Type Select “Fiber Type”, then “Return”.
(B) Perform Arc Test
Select “Arc Test”
Then perform the arc test
according to the
instruction.
*Fiber for testing is not
included in the kit.
Please check fiber type
inside the field fiber.
“Main Manu”
Select Sleeve Type Select Sleeve Type Then “Return”
See the operation manual of each splicer. These are the example of T-Q101-CA (T-71C).
Flat surface
Lever
Red dot
Lever
PC/UPC
APC
Flange Design
4 directions
available
1 direction only
(19) Put the front housing into the rear stopper.
(18) Key Alignment.