SEI FA433300TX User manual

FA433300TX
Electric Wall Fireplace
Assembly Instruction
For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[e-mail]
www.seidal.com

Electric Wall Fireplace
User’s Operating Manual
Consumer Safety Information
Please read this manual before installing and operating this appliance
Warning!!!
If the information in this manual is not followed exactly, an electric shock or fire may result in property damage, personal
injury or loss of life.
Do not store or use gasoline or other flammable vapors or liquids near this appliance.
Safety Feature:
This unit has an internal thermal overload protector. When an overheat temperature is
reached, the heater will automatically shut off. Operation can only resume when the unit is
reset. (See instructions below)
To Reset Heater:
Unplug the heater and wait 10 minutes for the unit to cool down. After 10 minutes, plug
the heater in again and follow the Operating Instructions described in this manual.
Important Operating and Safety Instructions
Important Operating And Safety Information
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire,
electric shock and injury to persons including the following:
1. Read all instructions before using this appliance.
2. This appliance is hot when in use. To avoid burns, don’t let bare skin touch hot surfaces. The air grille at the top of
this heater in particular will become hot when the heater is in use. Keep combustible materials such as furniture,
pillows, bedding, papers, clothes, curtains and etc. at least 3 feet(0.9m) away from the front of the appliance. Keep
all items away from the sides and back of the appliance and take special care not to block the air intake or exhaust
vents. Use handles when moving this heater.
3. Extreme caution is necessary when the appliance is near children and whenever the heater is left operating and
unattended.
4. Do not operate the appliance if the power cord or plug has been damaged or the heater has been damaged or
malfunctioned in any way. Do not use outdoors.
5. Do not use the appliance in bathrooms, laundry areas and similar indoor locations. Never locate the appliance
where it may fall into a bathtub or other water container.
6. Do not run the power cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not
route cord under furniture or appliances. Position the cord away from high traffic areas and such that it can not be
tripped over.
7. To disconnect the appliance, turn all controls “OFF”, then remove the plug from the outlet.
CAUTION:
High temperatures!
Keep draperies, electrical cords and other furnishings at least 3 feet from the front, sides and rear of heater.
WARNING:
--Risk of fire – Keep combustible material away from the front of the electrical fireplace.
--Service should be performed only while the electrical fireplace is disconnected from power supply.

8. This appliance has a polarized plug. This appliance must be connected to properly grounded outlets only. This plug
will fit fully in an outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. Do not change the
plug in any way.
9. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric
shock or fire, or damage the appliance.
10. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces like a bed,
where openings may become blocked.
11. Aheater has hot and sparking parts inside. Do not use in areas where gasoline, paint or flammable liquids are used
or stored.
12. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause
fire, electric shock or injury to persons.
13. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocate power tap.
14. Do not attempt to burn wood or other materials in this heater.
15. When transporting or storing the heater, keep both the unit and power cord/plug dry, free from excessive vibration
and away from heat sources.
DIMENSIONS:
PACKAGE CONTENTS
Part
Description Quantity
A Screw 3.5mm×8mm 2
B Plastic Expansion 6
C Screw 4mm×40mm 6
D L Bracket 1
E Mounting Bracket
1
A
B
C
D
E

Maintenance
Note
Light bulbs may become loose during shipping. If the flame effect is dim or does not operate properly at first, ensure that
the light bulbs are properly secured in the sockets (bulbs should be finger tighten, but do not over tighten). See “Replacing
Light Bulbs” Section of the manual for instructions.
When you first turn the heater on, it may emit a slight but harmless odor resulting from certain oils or greases being
heated as the appliance is used for the first time. This odor is perfectly safe and will stop shortly. It will not reoccur after
the first operation of this appliance.
This appliance comes equipped with an overheat protection safety device. Should the appliance begin to overheat for any
reason, it will automatically turn all heater functions of the appliance off. The appliance will have to be reset prior
to continuing
use. To reset the overheat protection safety device, turn all controls off and unplug the appliance, wait 10 minutes, plug th
e
appliance back in and turn on.
Replacing Light Bulbs:
1. Take off the front glass panel.
2. Remove the four screws from the side panel, located on the front of the unit, and remove front panel.
3. Locate and examine the bulbs to determine which bulb(s) require replacement.
4. Unscrew the bulb(s) counter clockwise.
5. Insert new bulb(s).
Cleaning
1. To remove dust from glass window, please use clean dry cloth.
2. To remove fingerprints or other marks from glass window, please use clean damp cloth. Do not spray glass cleaner or
other liquids directly onto the window.
3. Clean metal surfaces with a clean damp cloth making sure not to push dust or debris into any air intake or exhaust
vents.
4. Do not use abrasive cleaners or spray liquids on any part of the appliance.
Warning
: Before attempting to perform any maintenance on this appliance, turn all controls to the
“OFF” position and unplug. Allow the appliance to be “OFF” For at least 10 minutes before
performing any maintenance in order to allow all components to cool properly.
Warning
: Do not exceed the recommended Bulb wattage.
Use only 120V, 40W candelabra base light bulb, the lamp holder is model E12.
Light Bulbs
Screws
Front panel

Positioning/Locating Your Electric Fireplace
When choosing a location for your new fireplace, ensure that the general instructions are properly followed.
For best result, install the fireplace out of direct sunlight.
Installation Instructions
Before beginning installation of product make sure all parts are present. Compare parts with package contents list and
drawing above. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact
customer service for replacement parts.
Estimated Assembly Time: 15 minutes
Tools Required for Assembly (not included): Phillips screw driver, Drill, Hammer, Leveler
WALL MOUNTING INSTALLATION INSTRUCTIONS
1. Choose a wall location to attach the mounting bracket (E). Position the mounting bracket (E) in the desired location.
Use a leveler to align the bracket and mark the holes locations with a pencil. (One screw must be attached directly
into a wall stud. Wall anchor is not needed for this one screw).
2．Put the plastic expansion (B) anchors into the holes, use the screws to mount the plate.
3． Fix the L bracket (D) mounting part on the bottom of the fireplace, hang the fireplace on the fixed
mounting plate, mark the correct positions for the two holes on the L bracket (D) mounting part, drill the
holes and put in the expansions anchors, hang on the fireplace and screw securely.
4. Hang the front glass panel for the fireplace.

Operating Instructions
Control Panel Operating Procedures
NOTE:
When you first turn the heater on, it may emit a slight but harmless odor. This odor results from certain oils or greases
being heated as the appliance is used for the first time. This odor is perfectly safe and will stop shortly, it will not reoccur
after the first operation of the appliance.
Using the Control Panel:
Master Power Switch (A)
Open the cover and push buttonA down (1) to “on” position.(see FigureA)
Flame Effect
Push “ ” (On/Off) button or “ ” (On/Off) button on the remote control to begin flame effect. The red power light “ ”
will automatically come on. The flame effect can be adjusted by pressing or dimmer “ ” button on the remote control.
When pressed, the flame effect will cycle from high to low. Press the dimmer “ ” button on the remote control again to
lock in desired flame brightness. This brightness will be kept until the dimmer “ ” button on the remote control is
pressed again.
Heat Setting
1. Turning on Master Power Switch (A) and “O/I” (On/Off) button or “O/I” button on the remote control.
2. Press “ ” button on unit or remote control to activate the low heater setting. The red light above will indicate
that the heater is functioning on low.
3. Press “ ” button on unit or remote control again to shut off the heater.
4. Press “ ” button on unit or remote control to active the high heater setting. The red lights above the buttons will
indicate that the heater is functioning on high.
5. Press “ ” button on unit or remote control again to shut off the heater.
Electrical Connection
Grounding Instructions
This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for
the electric current to reduce the risk of electric shock. This product is equipped with a cord with an equipment-grounding
conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified
electrician or service technician if the grounding plug does not fit the outlet. Have a proper outlet installed by a qualified
electrician.
This product is for use on a nominal 120V circuit and has grounding plug that looks like that plug illustrated below. Make
B
C
D
A

sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with
this product.
NOTE: A 15AMP,120 Volts circuit is required. Dedicated circuit is preferred but not essential in all cases, a dedicated
circuit will be required if, after installation, the circuit breaker trips or the fuse blows on a regular basis when the heater is
operating.Additional appliance on the same circuit may exceed the current rating of the circuit break.
WARNING:
1. Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord
is stored or secured to avoid tripping or snagging to reduce the risk of fire, electric shock or injury to persons.
2. Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to
reduce the risk of fire, electric shock and injury to persons.
3. Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons,
always use a licensed electrician.
Before Using This Appliance:
1. Before permanently placing your electric fireplace, plug it into a convenient outlet to verify that the circuit breakers
for the outlet are on.
2. Light bulbs may become loose during shipping, if the flame effect is dim or does not operate properly at first,
ensure that the light bulbs are properly secured in the sockets (bulbs should be finger tightened, don’t over tighten)
see “Replacing Light Bulb” section of this manual for instructions.
3. The information regarding this appliance can be found on the rating plate located on the back of the unit.
Plugging In the Heater:
1. Make sure the appliance main “I/O” is switch OFF(refer to operating instruction section).
2. Plug the unit into a no less 15Amp/120V outlet.
TECHNIC L SPECIFIC TIONS
Model#
E 1119
Rate Voltage
C 120V, 60Hz
Rate Power
(Total)
1400W
Power of Heating pparatus
650W
(Low)
/1300W
(High)
Flame
effect
Power
80W
Motor Power
2
0W
Specificat
i
on of the Bulb
(
lamp
holder
)
2
P
cs E12
Using the Remote Control
This heater includes a remote control. To operate the appliance using the remote control, the Master Power Switch (A)
must be in the “ON” position. See below for directions to use the remote control:
ON/OFF BUTTON
DIMMER BUTTON
LOW HEATER BUTTON
HIGH HEATER BUTTON

TROUBLESHOOTING
FREQUENTLY ASKED QUESTIONS(FAQS)
PROBLEM POSSIBLE CAUSE SOLUTION
Flame is dim or not present 1. Light bulbs are burnt out
2. “Flame wand” has come loose
from bracket
1. Inspect light bulbs and replace
if necessary.(see Maintenance
section of this manual)
2. Remove screws holding back
panel in place and remove back
panel. Secure end of “flame
wand” back into the support
bracket.
No warm air is coming from the
heater 1.The overheat protection device in the appliance has been
triggered
1. Turn all controls off, unplug
the appliance, allow to cool for at
least 10 minutes, plug back in
and restart.
The appliance turns off and will
not turn back on 1.The overheat protection device in the appliance has been
triggered
2. House circuit breaker has
been tripped.
1. Turn all controls off, unplug
the appliance, allow to cool for at
least 10 minutes, plug back in
and restart.
2. Reset house circuit breaker.
Warning
: Turn off the appliance, unplug and let it cool for at least 10 minutes before attempting to
service. Only a qualified professional should attempt to service or repair the appliance

Please immediately examine this product carefully. Any request for missing parts or damage replacement must
be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this
time frame.Parts will not be available for items arriving fully assembled. We do not recommend modifying
product(s) and we are not responsible for any damages due to product modification(s). If damages or missing
parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement
merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
time if you have product issues or email us at serv[email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalo
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019