Seiwa LCTX0004V2 User manual

Constituent Parts
Product Outline LCTX0005V2 to 0007V2
LCTX0002V2 to 0004V2
●Precautions in use
‐
‐
Installation of the Floodlight
‐Don’t look straight at the LED. Your eyes might be impaired. Carry out installation work in consideration of interference between the floodlight and structure.
‐1.
‐
‐
‐
NB:
*
Fig. 3 Fig.4
2. Loosen the two screws on the wire connection box cover and remove the cover.
3.
4.
(a)LCTX0005V2～0007V2 (b)LCTX0002V2～0004V2 5. Carry out Class D grounding 󳊉100Ω or below󳊊for the floodlight using the grounding terminal in the wire connection box.
(recommended grounding terminal screw tightening torque: 1.3‐1.5N･m).
Fig. 1 Interference between the floodlight and the structure Adjustment of the illuminating angle
1.
‐The product is a stationary floodlight. If it is not fixed for use, a fire, electric shock, burn or fall might result.
‐2. After adjustment of the illuminating angle, tighten the handles firmly (recommended tightening torque: 22‐25 N･m).
LLPM00312‐2
The LCTX00022V2 to LCTX0004V2 have
different seat shapes from the above but
their installation dimensions are the same as
those of the LCTX0005V2 to LCTX0007V2.
Pass a 3‐wire cable with a final outside diameter of 10 to 14 mm (equivalent to or more than 600V 2PNCT (type 2 EP rubber‐insulated
chloroprene cabtyre cable) through the fastening nut, connect it to the terminal block as shown in Fig. 4 and tighten the terminal block screw
firmly at a recommended torque (1.3‐1.5 N･m). Fix the 3‐wire cable with the cable retainer securely and tighten the cable retainer screw at a
recommended torque (1.3‐1.5N･m) securely.
To adjust the illuminating angle, loosen the two handles with the floodlight supported by the angle adjusting grip securely (Fig. 2) and gently
adjust the illuminating angle. If the floodlight is not supported securely, it might suddenly turn, resulting in a damage or injury.
11E0000909A11
Installation manual
Rated input voltage
Voltage fluctuation range
Outdoor general application
Rain proof type
100‐242V
Tighten the two screws on the wire connection box cover evenly at a recommended torque (1.3‐1.5N ･m) securely to prevent rainwater
infiltration. Also tighten the fastening nut securely to prevent rainwater infiltration.
Inadequate tightening might cause the floodlight to fall, resulting in an accident.
Insert the two M16 mounting bolts into the hole of the seat placed on the mounting surface of the building with the specified interval between
them (55 mm) as shown in Fig. 3 and firmly tighten each mounting bolt together with a plain washer, spring washer and M16 hexagonal nut at
a recommended torque (94‐108 N･m). Inadequate tightening might cause the floodlight to fall and result in an injury.
LCTX0004V2
Wide angle
LCTX0005V2 to 0007V2：16kg LCTX0002V2 to 0004V2：28kg
5000[K]
When the floodlight is installed on the ground and its
upward angle range is from 30 to 60 degrees, it cannot be
fixed due to the presence of the mounting bolts (M16). If the
mounting bolts interfere with rotation of the floodlight for
angle adjustment, adjust the illuminating angle before fixing
the floodlight.
If a floodlight pedestal is used, note that this floodlight is heavier than conventional (HID) floodlights and a conventional pedestal may
not be rigid enough and cause an accident such as a fall. If you are going to use a pedestal, consult us.
Narrow angle
Don’t use the floodlight in a place where it may be water‐covered. The use in such a place might cause an electric leak, electric shock or
malfunction.
The color and brightness of LEDs fluctuate more largely than ordinary light sources such as candescent lamps and fluorescent lamps.
The color of light may vary with individual LEDs. Note that when the illumination distance is short, there may be uneven brightness or
color unevenness depending on the illuminated surface.
Gray metallic
Before installing the floodlight, confirm the range of motion of the floodlight as shown in Fig. 1(a) or 1(b). Paying attention to the
positional relation between the structure and the arm, take care that the floodlight does not contact the structure. An accidental
contact might cause a fire.
Be careful not to scratch the front cover of the floodlight. Scratching might cause damage, deterioration in watertightness or decline in
illuminance. If a crack is found in the front cover, let us know since it must be replaced immediately.
Application
Watertightness
Ambient temperature Frequency‐5～35℃
If the floodlight is used at a higher ambient temperature than 35°C or the LED is lit in a place exposed to direct sunlight, the internal
thermal fuse may be activated to turn off the LED. Though this is not a failure but a function to protect the electronic components, don’
t use the floodlight in such an environment. A temperature rise might cause a fire or electrical failure or shorten the LED life.
Item
Light distribution
Weight
Color temperature
Finish color
The angle adjusting grip (Fig. 2) is intended to be used for illuminating angle adjustment after installation and should not be used to
carry the fitting. If it is used to carry the fitting, the fitting might fall and cause an injury.
Luminaire model
name
Suitable wire 3‐wire cable with a final outside diameter of 10 to 14 mm
equivalent to or more than 600V 2PNCT (type 2 EP rubber‐insulated chloroprene cabtyre cable)
Rated voltage ±6%
50 / 60Hz
LED Floodlight
LCTX0005V2 LCTX0007V2
LCTX0002V2
LCTX0006V2
LCTX0003V2
Medium angle
Fig. 2
Front cover
Wire connection
box
Wire connection box cover
Angle adjusting grip
Handle
Angle adjusting grip Wire connection box cover Front cover
Wire connection bo
x
Handle
M16 hexagonal nut , Spring washer , Plain washe
r
M16 mounting bol
t
Mount
Hole (18)
Floodlight installation dimensions
Terminal block scre
w
Terminal bloc
k
Grounding
terminal screw Cable retainer
Cable retainer
screw
Fastening nu
t
3‐wire cable
Outside diamete
r

- Prior to use, please read the safety precautions and instruction manual thoroughly to use the product properly.
-
- Please keep the manual in a handy place for later reference.
●The various marks have the following meanings:
Improper handling may lead to a bodily injury or property damage.
Don’t touch.
Disassembly &
conversion
prohibited.
Don’t use near
a water source.
Be sure to
follow the
instructions.
Be careful of
ignition.
WARNING
The ambient temperature should be within the operating temperature range specified in the instruction manual. If the
product should be used at a temperature higher than specified, an early lighting failure or malfunction might occur or a fire
might result.
If a product must be oriented in a specific manner for use, install it properly according to the marking on its body or the
instruction manual. Otherwise, a fire or electric shock might result.
Be sure to
ground.
Prohibited.
For electrical connections, use crimp-type terminals, etc. to secure the connections and conduct insulation treatment. An
inadequate connection or inadequate insulation might cause an imperfect contact, leading to a fire or electric shock.
Do’t oert the produt.
Conversion might cause the product to fall or result in a fire or electric shock.
After installing the product, be sure to hand the safety precautions and instruction manual over to the user of the product.
Caution
WARNING:
CAUTION:
Improper handling may lead to a human death or serious bodily injury.
When leading the power cable into the product through a conduit or the like, waterproof the connection and joint
adequately to prevent water infiltration. Inadequate waterproofing might cause a fire or electric shock.
Be sure to turn
off the power.
In grounding work, be sure to follow the technical standards for electrical equipmentof your country. Inadequate grounding
might cause a fire or electric shock.
Don’t use the product in a hazardous location where a flammable or explosive atmosphere such as a gaseous, steamy or
dusty atmosphere may exist. Use in such a location might cause an explosion or fire.
Do’t ope LED lap protetie oers suh as the frot glass ad glass gloe.
Do’t touh a LED lap, otherise a alfutio or lightig failure ight our.
Do’t oer the produt ith a iflaale aterial suh as loth or paper or put aythig i the produt.
Such a material or thing might cause a fire.
Do’t ed, tist or pull the poer ale y fore.
Inadequate handling of the cable might damage it and result in a fire or electric shock.
Before cleaning, be sure to turn off the power.
Otherwise, a fire or electric shock might result.
11E0000741D11
Safety Precautions
To be conserved
L照般4
The parts once removed for cleaning should be replaced properly according to the instruction manual.
An improperly placed part might cause the product to fall, resultng in an injury or property damage.
- 1/2 -

Tokyo Branch
Never touch LED light sources and their surroundings.
The light sources and their surroundings are very hot, so an accidental touch might cause a burn.
Fax
SEIWA ELECTRIC MFG.CO., LTD.
Phone
For further information on the product, contact any of our offices listed below (if you like to make an inquiry, let us know the model name
indicated on the product nameplate).
CONTACT DETAILS
Fax
2-19-6 Yanagibashi, Taito-ku, Tokyo 111-0052 Japan
[phone]
[phone]
[phone]
Please note that the above addresses and phone numbers may be changed.
Phone
36 Shinike, Terada, Joyo, Kyoto Pref. 610-0192 Japan
Head Office
[phone]
To ensure brightness and safety, carry out periodical cleaning and inspection.
If used in an extended period without maintenance or inspection, a smoke, fire or electric shock might result.
A lighting fitting has a service life. A product which has been used for eight to ten years may have degraded internal parts
even if it looks normal. For safety and energy saving, we recommend you check and replace it.
*Operating conditions: ambient temperature of 30 °C, 10 hours per day, 3,000 hours per year. If used at a higher
temperature or more hours per year, the life would be shortened. Have a specialist inspect the product every three years.If
used for an extended period without inspection, a smoke, fire or electric shock might result.
CAUTION
For a product marked with a frequency, don’t use the product at a frequency other than 50 or 60 Hz (local power supply
frequency). Use at a wrong frequency might cause a fire.
Do’t use the produt at a oltage other tha the rated oltage idiated o the aeplate.
Otherwise, breakage, fire or electric shock might result.
Any product not marked as a product for outdoor use should not be used outdoors or in a humid place or near a water
source. Its use in such a place might cause a fire or electric shock.
The product should be mounted on a surface robust enough to support its weight, properly according to the instruction
manual. Improper installation might cause the product to fall or result in an electric shock or injury.
If you continue to use the product in an abnormal condition (smoke, odor, etc.), a fire or electric shock might result. If you
detect an abnormality, immediately turn off the power switch. Confirm that the abnormal condition has been eliminated
and make a repair call.
WARNING
L照般4
Installation of the product should be carried out by a qualified person.
Installation by an unqualified person is legally prohibited.
Don’t use the product in a strong corrosive gas atmosphere which contains hydrochloric acid or chlorine gases or the like.
Use in a corrosive gas atmosphere might cause the product to corrode and fall, resulting in an injury.
- 2/2 -