MegaLite Obra Flood N180 User manual

Table of Contents
Safety Information 3
Specifications 4
Photometrics 5
Main Power Connection 6
DMX-512 Connection 6
DMX Profile 7
Main Control Menu 9
Size and Weight 11
Rigging the Fixture 12
Cleaning & Maintenance 13
USER MANUAL

3
Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured
6. Maximum surface operating temperature 140º.
Protection Against Electrical Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. This fixture must not be left on for long periods of time.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured
6. Maximum surface operating temperature 140º.
Protection Against Electrical Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 6.
3. This unit must be earthed. (electronically grounded)
4. This fixture must not be left on for long periods of time.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.

Technical Information
4
Part Numbers
Fixture
Item # 4340—Obra Flood N180
Mechanical Specifications
Signal Connectors: Panel Mounted 5-pin XLR connectors in/out
Power Connectors: Panel Mount Power Con type in/out connection (Nema 5-15 to Blue power male cable included)
Thermal: Maximum ambient temperature 40° C
Maximum surface temperature 60° C
Display:Digital
Fastening System: Accessory clamp fixture track mounts
Lens Angle: 97°
Barndoors: Included
Diffuser: Included
Electrical Specifications
LED Type: 60 single color LEDs
Color Type: Deep Red, Red, Fire Red, Green, Aqua, Lime, Blue, UV, Amber
CRI: 62 on all colors on
CCT: 10809K @ full
LED Watts: 3 Watts each
LED Lifetime: 60,000 to 100,000 hours
Power Consumption: Universal 100 - 240V 50/60 Hz
Ballast: Electronic
Watts: 152W
Current: 1.26A
PF: 1.0
Protocol: DMX 512
RDM: Yes
DMX Channels: 4 Mode of Operation
Mode 4 Channel=Red (Deep Red, Red, Fire Red), Green (Green, Aqua, Lime) Blue (Blue, UV) Amber
Mode 9 Channel= Deep Red, Red, Fire Red, Green, Aqua, Lime, Blue, UV, Amber
Mode 10 Channel= Dimmer, Deep Red, Red, Fire Red, Green, Aqua, Lime, Blue, UV, Amber
Mode 14 Channel=Dimmer, Deep Red, Red, Fire Red, Green, Aqua, Lime, Blue, UV, Amber, Strobe, Macro, Macro
Speed, Dimmer Speed
Operating Mode: Stand alone 255 step dimmer setting via display
Auto preprogram via display
Control & Programming

Photometrics
5
Obra Flood N180
Obra Flood N180

6
Main Power Connection
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 220V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
DMX-512 Connection
This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to 60Hz
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120 Ohm re-
sistor between the (-) and the (+) signal into a 3 or 5 pin XLR plug and plug it in to the last fixture
on the signal run. Pre-manufactured terminator plugs are available for purchase from your Mega-
Lite dealer (P-DMXT).
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
Light Blue
Yellow/Green
Live
Neutral
Ground
L
N
220V
L
L
LN
110V—Connection 220V—Connection
DMX—input DMX—output
1. Shield
2. Signal (-)
3. Signal (+)
5
3
4
2
11
2
3
4
5
4. N/A
5. N/A
The fixture is equipped with 5 pin XLR cable mounted sockets for DMX input and output. The sockets are wired in paral-
lel. Only use a shielded twisted pair cable designed for RS-485 and 5 pin XLR plugs and connectors in order to connect
the controller with the fixture or the fixture with another.
LL

7
DMX Profile
Obra Flood N180 4 Channel Mode
DMX Channel Function Description Value Init
1LED Color Red LED intensity 0-255 255
2LED Color Green LED Intensity 0-255 255
3LED Color Blue LED Intensity 0-255 255
4LED Color Amber LED Intensity 0-255 255
Obra Flood N180 9 Channel Mode
DMX Channel Function Description Value Init
1LED Color Dark Red LED Intensity 0-255 255
2LED Color Red LED Intensity 0-255 255
3LED Color Fire Red Intensity 0-255 255
4LED Color Green LED Intensity 0-255 255
5LED Color Aqua LED Intensity 0-255 255
6LED Color Lime Red Intensity 0-255 255
7LED Color Blue LED Intensity 0-255 255
8LED Color UV LED Intensity 0-255 255
9LED Color Amber LED Intensity 0-255 255
Obra Flood N180 10 Channel Mode
DMX Channel Function Description Value Init
1Dimmer Dimmer 0-255 255
2LED Color Dark Red LED Intensity 0-255 255
3LED Color Red LED Intensity 0-255 255
4LED Color Fire Red Intensity 0-255 255
5LED Color Green LED Intensity 0-255 255
6LED Color Aqua LED Intensity 0-255 255
7LED Color Lime Red Intensity 0-255 255
8LED Color Blue LED Intensity 0-255 255
9LED Color UV LED Intensity 0-255 255
10 LED Color Amber LED Intensity 0-255 255

Obra Flood N180 14 Channel Mode
DMX Channel Function Description Value Init
1Dimmer Dimmer 0-255 255
2LED Color Dark Red LED Intensity 0-255 255
3LED Color Red LED Intensity 0-255 255
4LED Color Fire Red Intensity 0-255 255
5LED Color Green LED Intensity 0-255 255
6LED Color Aqua LED Intensity 0-255 255
7LED Color Lime Red Intensity 0-255 255
8LED Color Blue LED Intensity 0-255 255
9LED Color UV LED Intensity 0-255 255
10 LED Color Amber LED Intensity 0-255 255
No Function 0-10
11 Strobe Strobe (slow to fast) 11-115 0
Random (slow to fast) 116-255
No Function 0
12 Macro Fade 1-75 0
Chase 76-150
Color 151-255
13 Macro Speed No Function 0-10 0
Slow to Fast 11-255
No Function 1-50
Dimmer Speed 1 51-100
14 Dimmer Speed Dimmer Speed 2 101-150 0
Dimmer Speed 3 151-200
Dimmer Speed 4 201-255
8
Note: For Strobe function to work Dimmer Speed needs to be engaged.

Main Control Menu
The control board on the fixture is your interface to access and control
all the functions on the unit. Its digital display gives you a code view of
the options and functions. The following will explain each function and
its options.
9
Set Back
Mega Lite
Obra Flood
DMX Address
Press Center Red Knob to select the DMX start channel turn knob left or right to select DMX Start Channel keys,
Press Set to confirm the setting
DMX Mode
This function allows you to select the mode in witch you want to control the fixture. Press Center Red Knob turn the
knob left/right to select desired DMX mode settings. Press Set to confirm the settings.
4 CH Red, Green, Blue, Amber
Color Dimmer
This function allows you to dim up or down the LED’s . Press Center Red knob turn the knob left/right to select desired
color to adjust settings. Note:( Once fixture is powered down and powered up the fixture will return to last setting)
Menu:
DMX Add
Menu:
ChMode
9 CH
10 CH
Deep Red, Red, Fire Red, Green, Aqua, Lime, Blue, UV, Amber
Dimmer, Deep Red, Red, Fire Red, Green, Aqua, Lime, Blue, UV, Amber
Menu:
Dimmer
R1
Val:000
R2
Val:000
R3
Val:000
G1
Val:000
14 CH Dimmer, Deep Red, Red, Fire Red, Green, Aqua, Lime, Blue, UV, Amber,
Strobe, Macro, Macro Speed, Dimmer Speed
Deep Red
Red
Fire Red
Green
G2
Val:000
G3
Val:000
B1
Val:000
B2
Val:000
Aqua
Lime
Blue
UV
A1
Val:000 Amber

10
Info
Menu:
Fade
Fade
1Fade from one color to another slow speed 1 slowest to 15 fastest
Dim Curve
Press Center Red Knob to select dim curve type turn knob left or right to select fixture dimmer setting, Press Set
to confirm the setting (note: there is 0,1,2,3,4 options)
Menu:
Dim Curve
Temperature
Press Center Red Knob to read current temperature
Menu:
Info
Menu:
Fan
Fan:
Open
Fan will remain on all time
Fan:
Close Fan will remain off (Warning do not use this setting for long periods of time.)
Fan:
Auto Fan Speed will adjust depending on fixtures internal temperature (recommended use)
Info
Menu:
Info
RDM
Number
6342 Software
Version
V1.1
Info
Menu:
Cali
Cali
R1 This function will give the max output when used in DMX Mode. Press Center Red
Knob each output color can be set by setting max out from 255 the highest to 25 the
lowest. Press Set to Confirm setting

12.75”
Size and Weight
Size
12.75” x 5.33” x 11.75”
Packaged Size
15” x 12.5” x 8”
Weight
Net 14lb
Gross 15lb
11
11.75”
5.33”
6”
2.5”
3.5”

12
Rigging the fixture
Caution!
1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Use high quality installation equipment to hang unit.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-
ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you
lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the fixture has
got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be
checked at least one time a year by a skilled person.
Instructions;
To add mounting hardware slide 2
Bolts head first to track in position 1,2
or 3. Add clamp mounting hardware
then secure with 2 washers and nuts.
Please make sure all nuts are tight
and secure
1
2
3
There is 3 mounting track posi-
tions for the clamp mount.

Cleaning and Maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and
electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any
safety problems have to be removed.
Note: There is no serviceable parts inside the device except for the LED’s. Maintenance and service operations are to
be carried out by authorized dealers.
Replacing the fuse: When possible only replace the fuse with the same type and rating.
Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by authorized
dealers or trained professional only.
Should you have further questions , please contact your dealer.
Parts List
4340-PCB-MAI Main PCB card
4340-POW Power Supply
4340-CON-SIG Male & Female Signal Connection
4340-LED-MOD LED Module
4340-HOU-BAR-S Small Barn Door
4340-HOU-BAR-LLarge Barn Door
4340-PCB-DRI LED Driver
4340-PCB-DIS Display
4340-DIF Front Diffusion
4340-HOU-ROT Rotary Knob for display
4340-POW Power Supply
4340-HOU-MOU Clamp Mount
4340-PCB-POW Power Supply Relay
13

Mega-Lite
18668 Highway 16N
Helotes, Texas 78023
Ph 210-684-2600 Fax [phone]
www.mega.lighting / [e-mail]
Warranty Information
Warranty Conditions
-Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.
-LED’s and LAMPS are not guaranteed to match in color temperature or output.
-It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor.
If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
-Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of
the original invoice.
-Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical
means of shipment.
-Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS
INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any
warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, inci-
dental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by
product defect or the partial or total failure of any product regardless of the form of action, weather in contract, tort
(including negligence), strict liability or otherwise, and weather or not such damage was foreseen or unforeseen.
- Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Customer Support
Mega Lite has a customer support line to provide set up help and to answer any question should you encounter a prob-
lem. Please visit our website for any other related technical documents. For service related issue please contact our
service dept.
Monday—Friday 9am to 6pm CST
Voice: 210-684-2600
E-mail: [e-mail]
Document
Version Date Fixture Soware Notes
1.1 10/08/2019 V1.1
Manual Version
Please Visit www.mega.lighting for the most up to date manual version