Selecon PLZS1MKII-1834-03 Instruction Manual

For PLZS1MKII-1834-03 &
PLZS1MKII-2444-03

Selecon Offices
The material in this manual is for information purposes only and is subject to change without notice.
Selecon assumes no responsibility for any errors or omissions which may appear in this manual. For comments and
suggestions regarding corrections and/or updates to this manual, please visit the Selecon web site at
www.seleconlight.com or contact your nearest Selecon office.
El contenido de este manual es solamente para información y está sujeto a cambios sin previo aviso.
Selecon no asume responsabilidad por errores o omisiones que puedan aparecer. Cualquier comentario, sugerencia
o corrección con respecto a este manual, favor de dirijirlo a la oficina de Selecon más cercana.
Der Inhalt dieses Handbuches ist nur für Informationszwecke gedacht, Aenderungen sind vorbehalten.
Selecon uebernimmt keine Verantwortung für Fehler oder Irrtuemer, die in diesem Handbuch auftreten. Für
Bemerkungen und Verbesserungsvorschlaege oder Vorschlaege in Bezug auf Korrekturen und/oder
Aktualisierungen in diesem Handbuch, moechten wir Sie bitten, Kontakt mit der naechsten Selecon-
Niederlassung aufzunehmen.
Le matériel décrit dans ce manuel est pour information seulement et est sujet à changements sans préavis. La
compagnie Selecon n'assume aucune responsibilité sur toute erreur ou ommission inscrite dans ce manuel. Pour
tous commentaires ou suggestions concernant des corrections et/ou les mises à jour de ce manuel, veuillez s'il vous
plait contacter le bureau de Selecon le plus proche.
Note: Information contained in this document may not be duplicated in full or in part by any person without prior written
approval of Selecon. Its sole purpose is to provide the user with conceptual information on the equipment mentioned. The use of
this document for all other purposes is specifically prohibited.
Document Number: 02.9691.2001
Version as of: 01 September 2015
PLPROFILE1 MKII LED Luminaire Installation & User’s Manual
Selecon - Dallas
10911 Petal Street
Dallas, TX 75238
Tel: [phone]
Fax: [phone]
Selecon - Asia Limited
Unit C, 14/F, Roxy Industrial Centre
No. 41-49 Kwai Cheong Road Kwai
Chung, N.T., Hong Kong Tel: +852
2796 9786
Fax: [phone]
Selecon - Auckland
19-21 Kawana Street
Northcote, Auckland 0627
New Zealand
Tel: [phone]
Fax: [phone]
Selecon - Europe
Rondweg zuid 85
Winterswijk 7102 JD
The Netherlands
Tel: [phone]
Website:
www.seleconlight.com

1
PLPROFILE1 MKII LED Luminaires Installation & User’s Manual
IMPORTANT INFORMATION
Warnings and Notices
Additional Resources for DMX512
For more information on installing DMX512 control systems, the following publication is available for purchase
from the United States Institute for Theatre Technology (USITT), "Recommended Practice for DMX512: A Guide
for Users and Installers, 2nd edition" (ISBN: 9780955703522). USITT Contact Information:
USITT
315 South Crouse Avenue, Suite 200
Syracuse, NY 13210-1844
Phone: [phone] or 1.315.463.6463
www.usitt.org
Selecon Limited Three-Year Warranty
Selecon offers a three-year limited warranty of its luminaires against defects in materials or workmanship from
the date of delivery. A copy of the Selecon three-year limited warranty containing specific terms and conditions
can be obtained from the Selecon web site at www.seleconlight.com or by contacting your local Selecon office.
PLPROFILE1 MKII LED Luminaire powerful LED engine offers exceptional performance and life. Under
normal operating conditions, our LED engine has a life expectancy in excess of 50,000 hours, however under
worst case operating conditions with the luminaire set to continuous full output it is possible that a small
percentage of LED’s may require replacement sooner. The Selecon three-year limited warranty includes our
guarantee against premature failure of the LED engine.
When using electrical equipment, basic safety precautions should always be followed including the following:
a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b. Do not use outdoors.
c. Do not mount near gas or electric heaters.
d. Equipment should be mounted in locations and at heights where it will not readily be subjected to
tampering by unauthorized personnel.
e. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
f. Do not use this equipment for other than intended use. This equipment is not for residential
installation or use.
g. Refer service to qualified personnel.
SAVE THESE INSTRUCTIONS.
WARNING: You must have access to a main circuit breaker or other power disconnect device
before installing any wiring. Be sure that power is disconnected by removing fuses or turning the
main circuit breaker off before installation. Installing the device with power on may expose you to
dangerous voltages and damage the device. A qualified electrician must perform this installation.
WARNING: Refer to National Electrical Code® and local codes for cable specifications. Failure to
use proper cable can result in damage to equipment or danger to personnel.
WARNING: This equipment is intended for installation in accordance with the National Electric
Code® and local regulations. It is also intended for installation in indoor applications only. Before
any electrical work is performed, disconnect power at the circuit breaker or remove the fuse to avoid
shock or damage to the control. It is recommended that a qualified electrician perform this
installation.

Installation & User’s Manual PLPROFILE1 MKII LED Luminaires
2TABLE OF CONTENTS
TABLE OF CONTENTS
Selecon Offices........................................................................................................ Inside Front Cover
IMPORTANT INFORMATION
Warnings and Notices...................................................................................................................................... 1
Additional Resources for DMX512................................................................................................................. 1
Selecon Limited Three-Year Warranty ............................................................................................... 1
TABLE OF CONTENTS
PREFACE
About this Manual .................................................................................................................................................. 4
Accessories ............................................................................................................................................................. 4
PLPROFILE1 MKII LED Luminaire Power Input Cables ............................................................................. 4
PLPROFILE1 MKII LED Luminaire Zoomspot Lenses ................................................................................ 4
PLPROFILE1 MKII LED Luminaire Imaging Accessories ........................................................................... 4
PLPROFILE1 MKII LED Luminaire Clamps ................................................................................................ 4
PLPROFILE1 MKII LED Luminaire USB Luminaire Software Cable ......................................................... 4
PLPROFILE1 MKII LED Luminaire Top Box Assembly.............................................................................. 4
PLPROFILE1 MKII LED Luminaire OVERVIEW
PLPROFILE1 MKII LED Luminaire Components................................................................................................ 5
Major Luminaire Components ........................................................................................................................ 5
Top Box (PLICB) Luminaire Connections ..................................................................................................... 6
LCD Display / Menu System .......................................................................................................................... 6
INSTALLATION AND SET UP
Power Requirements............................................................................................................................................... 7
Connecting Power................................................................................................................................................... 7
Connecting to the DMX512 Network..................................................................................................................... 8
Mounting ................................................................................................................................................................ 9
Using Supplied C-Clamp................................................................................................................................. 9
Safety Cable Use ........................................................................................................................................... 10
Pan and Tilt Adjustments...................................................................................................................................... 10
Pan Adjustment ............................................................................................................................................. 10
Tilt Adjustment.............................................................................................................................................. 10
FOCUS AND BEAM ADJUSTMENTS
Lens Tray Removal and Installation ..................................................................................................................... 11
Zoom and Focus Adjustments .............................................................................................................................. 11
Beam Shutter Operation ....................................................................................................................................... 12
Gobo/Iris Access Panel......................................................................................................................................... 13
OPERATION AND PROGRAMMING
LCD Menu Operation........................................................................................................................................... 14
LCD Menu System ............................................................................................................................................... 15
Menu Structure ..................................................................................................................................................... 16
Security................................................................................................................................................................. 18
Locking Fixture ............................................................................................................................................. 18
Presets................................................................................................................................................................... 19
Editing Preset Names .................................................................................................................................... 19
Settings ................................................................................................................................................................. 19

3
PLPROFILE1 MKII LED Luminaires Installation & User’s Manual
DMX CONTROL
16-Bit Mode.......................................................................................................................................................... 21
8-Bit Mode............................................................................................................................................................ 23
DMX 5-Channel (5-Chan) Mode ......................................................................................................................... 25
PLPROFILE1 MKII LED Luminaire DMX Timing Channel Detail................................................................... 25
PLPROFILE1 MKII LED Luminaire RDM Parameter IDs................................................................................. 31
CLEANING AND CARE
Special Cleaning and Care Instructions................................................................................................................ 34
Lens Tray Assembly Cleaning ............................................................................................................................. 34
Service and Maintenance...................................................................................................................................... 35
Accessories ........................................................................................................................................................... 35
TROUBLESHOOTING
Troubleshooting Guide ......................................................................................................................................... 36
TECHNICAL SPECIFICATIONS
PLPROFILE1 MKII LED Luminaire Operational Specifications ....................................................................... 37
PLPROFILE1 MKII LED Luminaire Dimensions............................................................................................... 37

Installation & User’s Manual PLPROFILE1 MKII LED Luminaires
4PREFACE
PREFACE
1. About this Manual
The document provides installation and operation instructions for the following products:
• PLPROFILE1 MKII LED Luminaire, 18-34 Degree Zoomspot (PLZS1MKII-1834-03).
• PLPROFILE1 MKII LED Luminaire, 24-44 Degree Zoomspot (PLZS1MKII-2444-03).
Please read all instructions before installing or using this product. Retain this manual for future reference. Additional
product information and descriptions may be downloaded at www.seleconlight.com.
Note: All PLPROFILE1 MKII LED Luminaires are universal voltage (100VAC to 240VAC, Auto-ranging).
2. Accessories
Contact your Authorized Selecon Dealer for price and availability of all accessories for PLPROFILE1 MKII LED
Luminaires. Additional information can be found on the Selecon web site at www.seleconlight.com.
PLPROFILE1 MKII LED Luminaire Power Input Cables
PLPROFILE1 MKII LED Luminaire Zoomspot Lenses
PLPROFILE1 MKII LED Luminaire Imaging Accessories
PLPROFILE1 MKII LED Luminaire Clamps
PLPROFILE1 MKII LED Luminaire USB Luminaire Software Cable
PLPROFILE1 MKII LED Luminaire Top Box Assembly
Part Number Description
PC1BE PLPROFILE1 MKII LED Luminaire AC Power Input Cable (39 inches / 1 meter), Powercon without
Connector (user to supply AC connector)
PC1GP PLPROFILE1 MKII LED Luminaire AC Power Input Cable (39 inches / 1 meter), Powercon with
Stagepin Connector
PC1GTL PLPROFILE1 MKII LED Luminaire AC Power Input Cable (39 inches / 1 meter), Powercon with
Twistlock Connector
PC1GR PLPROFILE1 MKII LED Luminaire AC Power Input Cable (39 inches / 1 meter), Powercon with
Edison Connector
PC3PC PLPROFILE1 MKII LED Luminaire PowerCon Male to PowerCon Female 2.5 Meter Cable for
interconnection between units
Part Number Description
15ACAX1834LT Acclaim Axial Zoomspot 18-34 Degrees Lens Tray, Black
15ACAX2444LT Acclaim Axial Zoomspot 24-44 Degrees Lens Tray, Black
Part Number Description
15ACGH Acclaim Axial Zoomspot Rotatable Gobo Holder (Black Handle, Steel M Sized Gobos)
15ACGHGL Acclaim Axial Zoomspot Rotatable Gobo Holder (Black Handle, Glass M Sized Gobos)
15ACIRIS Acclaim Axial Zoomspot Iris
15ACSM Acclaim Axial Zoomspot Lens Safety Mesh
ACCDONUT Acclaim Axial Zoomspot Donut
20CFMF Acclaim Axial Zoomspot Replacement Color Frame, 4-7/8 Inch Square, Black
Part Number Description
SC Selecon Molded Yoke Rated C-Clamp
MC Mega Claw, Black Anodized
Part Number Description
PEGASUS USB Luminaire Software Programming Kit (for updating luminaire firmware) - includes USB Upload
Cable, QuickStart Guide, and Carry Bag
Part Number Description
PLICB Spare Top Box (Interconnect) Assembly

PLPROFILE1 MKII LED Luminaire Components 5
PLPROFILE1 MKII LED Luminaires Installation & User’s Manual
PLPROFILE1 MKII LED LUMINAIRE OVERVIEW
1. PLPROFILE1 MKII LED Luminaire Components
Major Luminaire Components
Figure 1: PLPROFILE1 MKII LED Luminaire Components
*For the LCD Display Menu System, refer to "LCD Display / Menu System" on page 6 for more information.
Front of Unit
Rear of Unit
Lens Tube Assembly
Top Box Assembly (PLICB)
(AC Input/Thru and DMX In/Out Connections)
Safety Cable
Anchor Point
Beam Angle Adjustment
Beam Focus Adjustment
Beam Shutter (4 each)
Yoke Locking Handle
LCD Display /
Menu System*
Multi-Conductor
Fixture Connection
Accessory Holder
(with latching door)

Installation & User’s Manual PLPROFILE1 MKII LED Luminaires
6PLPROFILE1 MKII LED Luminaire OVERVIEW
Top Box (PLICB) Luminaire Connections
Figure 2: Top Box (PLICB) Connections
LCD Display / Menu System
Figure 3: PLPROFILE1 MKII LED Luminaire LCD Display & Menu System
DMX512 Output/Thru
DMX512 Input
AC (Power) Output
AC (Power) Input
Multi-Conductor Top Box
to Luminaire Connection
Multi-Conductor Top Box
to Luminaire Connection
Side View 1
Side View 2
1) LCD Display (Menu System)
2) Preset / Intensity / Menu Access Buttons
3) Function (Menu System) Select Push Buttons
1
Note: For Menu operation and programming details,
refer to "LCD Menu Operation" on page 14.
2
3

Power Requirements 7
PLPROFILE1 MKII LED Luminaires Installation & User’s Manual
INSTALLATION AND SET UP
1. Power Requirements
WARNING! The PLPROFILE1 MKII LED Luminaire should be connected to a constant circuit or a relay device. It
should never be connected to a dimmer or circuit controlled by a dimmer.
The PLPROFILE1 MKII LED Luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire
contains an auto-ranging power supply. Depending on supply voltage, each luminaire can draw up to 140 Watts. The
maximum through current should not exceed 20 Amps*.
WARNING! *The Maximum Allowable Input Current of 20 Amps (and the maximum power supply limit of 140
Watts). Do not overload circuits! Must be supplied by a branch circuit protected by a maximum 20 Amp circuit
protector. Doit être alimenté par un circuit de dérivation protégé par un maximum de 20 ampères circuit
protecteur. Do not overload circuits!
IMPORTANT AC POWER CONNECTION NOTES:
a. Must be supplied by a branch circuit protected by a maximum 20 Amp circuit protector. Doit être
alimenté par un circuit de dérivation protégé par un maximum de 20 ampères circuit protecteur.
b. When using the daisy-chain connection method, ONLY connect PLPROFILE1 MKII LED Luminaires
to AC Output Connection of PLPROFILE1 MKII LED Luminaires. DO NOT CONNECT OTHER
TYPES OF LUMINAIRES OR DEVICES!
c. Use only approved cable types.
d. Do not overload circuits!
e. Do not connect PLPROFILE1 MKII LED Luminaires to dimmed circuits.
f. The MAXIMUM allowable number of PLPROFILE1 MKII LED Luminaires which can be 'daisy-
chained' on one power feed should not exceed ratings. DO NOT EXCEED!
2. Connecting Power
Units can be powered in one of two ways:
• Direct connection to a AC power source using an AC input cable.
• Daisy chain connection using a interconnect AC cable.
If the unit is supplied with an AC input cable but you did not order an AC input connector, Table 1 on page 8
describes how to connect power to your PLPROFILE1 MKII LED Luminaire. Field wiring of the PLPROFILE1
MKII LED Luminaire is straight forward. A total of 3 wires/conductors need to be brought to the unit. The following
wiring scheme is required:

Installation & User’s Manual PLPROFILE1 MKII LED Luminaires
8INSTALLATION AND SET UP
Table 1: PLPROFILE1 MKII LED Luminaire AC Input
Connections
3. Connecting to the DMX512 Network
Basic DMX512 installation consists of connecting multiple PLPROFILE1 MKII LED Luminaires together (up to 30
luminaires) in "daisy-chain" fashion. A cable runs from the control console (or DMX512 control source) to the DMX
connector on the first PLPROFILE1 MKII LED Luminaire. Another cable runs from the other DMX connector on the
first unit to a DMX connector on the next PLPROFILE1 MKII LED Luminaire (or DMX512 device to be controlled).
Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on
page 1. For PLPROFILE1 MKII LED Luminaire DMX Mapping, refer to "DMX CONTROL" on page 21.
Figure 4: PLPROFILE1 MKII LED Luminaires - DMX512 Connections
Wire Color Purpose
Brown Main / Line (100 to 240VAC)
Blue Neutral
Green/Yellow Ground
Neutral Main /
Ground / Earth
Line
AC Input Connector
(on back of unit)
DMX512
DMX512 (out from first
to second luminaire)
DMX512 (out to the next luminaire or
DMX512 controlled device)
PLPROFILE1 MKII LED Luminaires
(from console or
control device)
DMX512 Connections
Data Thru
Cable Pinout
Male Conn
Pin 1
Common
(Drain)
Pin 2
Data (-)
Pin 3
Data (+)
Pin 4
Not Used
Pin 5
Not Used
Data In
Cable Pinout
Female Conn
1
2
3
4
5
1
2
3
4
5

Mounting 9
PLPROFILE1 MKII LED Luminaires Installation & User’s Manual
4. Mounting
WARNING! Before attempting any installation or service, disconnect all power at power source. Dimming the
luminaire does not disconnect power. Installation and service should only be performed by a trained and qualified
professional.
Using Supplied C-Clamp
As illustrated in Figure 5, at yoke assembly, thread clamp mounting bolt (with washer installed) through center clamp
mounting hole at top of yoke, through Top Box Assembly, and thread bolt into C-Clamp. Securely tighten bolt (by
hand) into clamp (but do not over-tighten).
Note: Top box will be able to swivel once bolt is tightened by design. DO NOT OVER-TIGHTEN!
Figure 5: Luminaire Mounting
To mount on a telescopic stand, reverse the yoke under the luminaire and bolt to stand. Please note luminaire
orientation (see note in Figure 5) for proper cooling.
Note: After installing Clamp and Top Box assembly, connect luminaire cable assembly to Top Box Assembly before
mounting luminaire. Please note that the cable connector is keyed.
Yoke Assembly
Center Clamp Mounting Hole (13 mm)
NOTE: To allow for proper cooling, make sure
luminaire head is orientated as shown (with
cooling vents pointed upwards).
Top Box Assembly
C-Clamp
Flat Washer
C-Clamp Bolt*
Top Box Assembly
Luminaire Cable Assembly
WARNING! *When installing a C-Clamp (or hook,
or other type of clamp) with the Top Box Assembly
as shown, you MUST use the C-Clamp Bolt
supplied with the fixture. Failure to do so may result
in damage to the Top Box Assembly or cause the
luminaire to dislodge from the clamping device.
Flat Washer

Installation & User’s Manual PLPROFILE1 MKII LED Luminaires
10 INSTALLATION AND SET UP
Safety Cable Use
The supplied safety cable MUST always be used when rigging luminaires on bars, truss, etc. (as shown in Figure 6).
The supplied safety cable is recommended for all hanging installation and may be required by national and local
codes. Loop or attach safety cable to luminaire safety cable anchor point as shown and attach to structure. You should
always consult and follow all local and national codes and regulations for mounting and installation of luminaire.
5. Pan and Tilt Adjustments
Pan Adjustment
The pan adjustment of a PLPROFILE1 MKII LED Luminaire is achieved by loosening the yoke bolt of the securing
clamp attached to the luminaire's yoke assembly. Loosen the bolt, set the luminaire to the desired position and re-
tighten.
Tilt Adjustment
PLPROFILE1 MKII LED Luminaires offer variable tilt settings. The unit can be set at a specific angle (in relation to
its mounting position) or at an angle between 0 to 90 degrees. When the yoke is in the position shown in Figure 6, you
have full range access to shutters the gate etc. If you flip the yoke over some access is reduced but the over all volume
the luminaire takes up is reduced. This is particularly useful in tightly hung lighting positions or in theatres with low
grids.
Figure 6: Luminaire Tilt Adjustment
To adjust and set tilt angle of the luminaire:
Step 1. Mount luminaire in desired location (see "Mounting" on page 9 for more information).
Step 2. Loosen, but do not remove, T-Handle Tilt Lock at base of yoke assembly as shown in Figure 6.
Step 3. Position luminaire to desired tilt position.
Step 4. Hand-tighten T-Handle Tilt Lock to set position.
Yoke Assembly
Cooling Vents (see note below)
T-Handle Tilt Lock
NOTE: To allow for proper cooling, make
sure luminaire head is orientated as shown
(with cooling vents pointed upwards).
Safety Cable
Sliding Yoke Assembly
Safety Cable
Anchor Point.
SAFETY CABLE: FOR LUMINAIRE, the supplied safety cable is
recommended for all hanging installation and may be required by
national and local codes. Loop/attach safety cable to safety cable anchor
point (as shown) and attach to structure.
(supplied with
luminaire)

Lens Tray Removal and Installation 11
PLPROFILE1 MKII LED Luminaires Installation & User’s Manual
FOCUS AND BEAM ADJUSTMENTS
1. Lens Tray Removal and Installation
It is easy and quick to change to the lens tray on a PLPROFILE1 MKII LED Luminaire. Zoomspot lens trays (as
shown in "PLPROFILE1 MKII LED Luminaire Zoomspot Lenses" on page 4) are interchangeable.
To remove and install lens tubes:
Step 1. Before proceeding, it is recommended to move the zoom and focus lenses towards the center of the lens tray
assembly (away from the front and back edges).
Step 2. Unlatch lens tray as illustrated Figure 7. Be careful as the lens tray assembly will swing open if not properly
supported.
Figure 7: Lens Tray Assembly Removal
Step 3. With lens tray assembly open (hanging down), lift lens tray assembly up and out of its hinged position to
free it from luminaire.
Step 4. To install perform process in reverse.
CAUTION: Ensure the lens tray assembly locking catch is fully engaged before putting fixture into use.
2. Zoom and Focus Adjustments
To adjust zoom/beam angle and focus:
Step 1. Make sure all frame shutters are open (out of beam path). See "Beam Shutter Operation" on page 12 for
more information.
Step 2. As shown in Figure 8, loosen Zoom Adjustment Knob and set beam angle as desired.
Step 3. Hand-tighten Zoom Adjustment Knob to lock position.
Step 4. Loosen Focus Adjustment Knob.
Step 5. Move Focus Adjustment Knob along forward (or back) until beam focus is set as desired.
Lens Tray Assembly
Lens Tray Latch
PLPROFILE1 MKII LED Luminaire

Installation & User’s Manual PLPROFILE1 MKII LED Luminaires
12 FOCUS AND BEAM ADJUSTMENTS
Step 6. Hand-tighten Focus Adjustment Knob to lock position.
Figure 8: Zoom and Focus Adjustment Knobs
3. Beam Shutter Operation
Each PLPROFILE1 MKII LED Luminaire is equipped with four independent shutters (as shown in Figure 9) to block
or shape light as desired. After the luminaire is installed and positioned, move the shutters in or out as desired.
Figure 9: PLPROFILE1 MKII LED Luminaire Beam Shutters
Zoom Adjustment Knob
Shutter (4 ea.)
Focus Adjustment Knob
Lens Tray Assembly
Beam Shutter
(4 each) Front View
Move beam shutters
in and out as desired.

Gobo/Iris Access Panel 13
PLPROFILE1 MKII LED Luminaires Installation & User’s Manual
4. Gobo/Iris Access Panel
Each PLPROFILE1 MKII LED Luminaire is capable of holding one gobo holder, containing one "M" size glass or
steel gobo. PLPROFILE1 MKII LED Luminaires are not supplied gobo holders or an iris. These items can be
purchased from your local Authorized Dealer. For more information, refer to "PLPROFILE1 MKII LED Luminaire
Imaging Accessories" on page 4.
To install or change a gobo:
Step 1. As shown in Figure 10, locate gobo/iris access slot.
Step 2. Install gobo into gobo holder in desired orientation.
Step 3. Slide gobo holder into luminaire gobo slot making sure to "catch" slots in interior of gobo slot closest to
shutters.
Figure 10: PLPROFILE1 MKII LED Luminaire Gobo Holder and Gobo Installation
Gobo
Image
Gobo / Iris Access Slot
Gobo Holder

Installation & User’s Manual PLPROFILE1 MKII LED Luminaires
14 OPERATION AND PROGRAMMING
OPERATION AND PROGRAMMING
1. LCD Menu Operation
The PLPROFILE1 MKII LED Luminaire’s LCD Display and Menu System provides local control for accessing all
the fixture’s status information, menu options, and settings.
Note: If there are multiple luminaires in a system, changes would need to be made at each LCD Menu as desired.
Upon power up, the LCD will display the main screen showing the product type/name. If DMX is enabled, the
programmed address will appear after power up.
Figure 11: LCD Display and Menu System
Up/Down/Left/Right Arrow Buttons -
Navigates menu system and used for
Escape (ESC) / Menu Button -
Enters menu options. Navigates
OK (Enter) Button -
Accesses details, activates
a field, or enters a setting
depending on the current menu item.
selecting and setting options.
(backs up) one menu level.
PRESET Button -
Allows the recall of
LCD Display -
Displays all menu parameters and
option settings. Also displays DMX512
address (DMX models only).
INTENSITY Button -
Allows the customization of current intensity (light
output). Note, using the LEFT and RIGHT arrow
buttons you can select each RGBW channel
individually and change their intensity using the UP
and DOWN arrows.
stored presets.

LCD Menu System 15
PLPROFILE1 MKII LED Luminaires Installation & User’s Manual
2. LCD Menu System
The LCD Display Menu system consists of several categories. Use the four arrow buttons as required (refer to Figure
11 on page 14) to access and make changes to the menu items. When the desired menu item is reached, press [OK] to
display the menu options. Use navigation and [OK] buttons to view status and configure the LCD Menu as required.
Note: Refer to "Menu Structure" on page 16 for complete structure and settings.
To navigate and access menu settings/selections:
Step 1. At Main Menu, press [ESC] / [MENU] button once. Another window will appear with sub-menu categories:
• Save as Preset
• Edit a Preset
• Color Mixer
• Settings
• Lock Fixture
• Fixture Status
•NormalizeColors
Step 2. Press [OK] at desired menu item to access and make changes.
Step 3. Make changes as desired.
Note: When DMX512 signal is present, Edit Preset and Color Mixer options will not appear in menu structure.
To navigate fixture status menus:
Step 1. At default screen, press LEFT or RIGHT arrow button once. The default menu screen will change to allow
for quick reference to the following items (note, depending on which arrow button is pressed, status screens
may appear in reverse order):
a. DMX Address (note, if fixture is UNLOCKED, hit [OK] to change DMX address).
b. Fixture Hours (displays fixture operating hours since last reset).
c. Fixture Power (displays Max Power Limit setting (in Watts), Present Power consumed by fixture (in
Watts), and Hours of Use).
d. Fixture Status (displays current operational temperature, LED status, and fan speed setting).
Step 2. Press LEFT or RIGHT arrow buttons to scroll through status screens.
Step 3. Press [ESC] at anytime to access Main Menu.

Installation & User’s Manual PLPROFILE1 MKII LED Luminaires
16 OPERATION AND PROGRAMMING
3. Menu Structure
Note: See "To navigate and access menu settings/selections:" on page 15 to learn how to access menus. To save
changes, hit [OK]. Press [ESC] to cancel any changes you made.
MAIN MENU
Save a Preset
Sub Menu Options Comments
Select Preset to Save - (Option)
Scrolls and sets current user-defined
color mix to various recallable presets
in the fixture using arrow buttons.
Note: To edit a current (set) preset,
see Edit Presets.
Off Users can:
• Save the current settings (look) to
a specific recallable Preset in the
fixture’s memory.
• Edit the levels (values) for Red,
Green, Blue, White, and Intensity
values (in percent%) by using the
arrow buttons. Once the values
are adjusted, the preset is saved
as desired.
*Only intensities may be stored on
White Color Temperature presets.
RGBW in these presets cannot be
edited or changed.
Scratch Pad
Warm White*
Cool White*
Day Light*
Preset X (5 through 31)
Continued next page
LCD Display /
Menu System

Menu Structure 17
PLPROFILE1 MKII LED Luminaires Installation & User’s Manual
Menu Structure (continued)
Edit a Preset
Sub Menu Options Comments
Select Preset to Edit - (Option)
Selects a current preset and outputs
the preset, so preset can be edited.
Note: To save a specific look of the
fixture, see Save Presets.
For additional information, refer to
"Presets" on page 19.
Off
Users can:
• Edit the current settings (look) to a
specific recallable Preset in the fix-
ture’s memory.
• Edit the values for Red, Green,
Blue, White, and Intensity values
(in percent%) by using the arrow
buttons.
• Once the values are adjusted, the
"Save Preset" menu option
appears to save the edits.
NOTES:
*Only intensities may be stored on
White Color Temperature presets.
RGBW in these presets cannot be
edited or changed.
**If a Calibrated Preset's Color Mix is
changed (5 thru 25), an asterisk '*' is
appended to the end of the name to
indicate that it has been modified.
This only happens if the name
matches the original calibrated name,
stored in EEPROM. This does not
happen if the Intensity is changed,
only the color mix.
Scratch Pad
Warm White*
Cool White*
Day Light*
Preset X (5 through 31)**
Note: When DMX512 signal is present, Edit a Preset option will not appear in menu structure.
Color Mixer
Sub Menu Options Comments
Select Color or Intensity to Adjust -
(Option)
Red
Users can:
• Edit Red, Green, Blue, White, and
Intensity values (in percent%) by
using the arrow buttons.
• Once the values are adjusted,
press [OK] to save the edits to
scratch pad.
Green
Blue
White
Intensity
Note: When DMX512 signal is present, Color Mix option will not appear in menu structure.
Continued next page
Continued from previous page
Settings
Sub Menu Options Comments
SETTINGS - (Option)
Scrolls and sets the various fixture
settings using arrow buttons.
See "Settings" on page 19 for details.

Installation & User’s Manual PLPROFILE1 MKII LED Luminaires
18 OPERATION AND PROGRAMMING
Menu Structure (continued)
4. Security
Unwanted changes to the Fixture's Configuration or Setting can be controlled by locking the fixture’s menu.
PLPROFILE1 MKII LED Luminaires are shipped with a default numeric PIN code of "0000" (four zeros). Users may
set their own PIN code (four-digit number) via Settings > General > Set PIN. When setting a PIN code, write it
down and keep it in a secure location. Note, Selecon does not have records of PIN codes established by users or
owners.
Note: Contact Selecon technical support if a unit is locked and the PIN code is lost for instructions on how to reset
luminaire.
Note: If the Fixture is locked when it is powered down the fixture will remain in the locked state when powered up.
Locking Fixture
To lock the fixture:
Step 1. At Main Menu, press [MENU] and scroll to Lock Fixture. Note, default PIN is "0000" (four zeros).
Step 2. Press [OK].
Step 3. Enter four-digit, user-selectable, PIN code.
Step 4. Use [LEFT ARROW] or [RIGHT ARROW] keys to highlight "YES", press [OK] or [ESC] twice to cancel
action.
Step 5. Fixture is now locked if locking process was not canceled as described in previous step.
Continued from previous page
Lock Fixture
Sub Menu Options Comments
Enter PIN Lock / Are you sure?
Use arrow buttons to make selection.
Press [OK] to accept. Note, a PIN
code must be established (set) in
order to lock a fixture. Locking the
fixture will disable access to changing
menu settings. For details, refer to
"Security" on page 18.
Fixture Status
Sub Menu Options Comments
LED Status Information
Scrolls through the various levels.
Depending on the arrow button
pressed, the screens may appear in a
different order that shown in
"Options".
LED 1
Displays LED’s current status (in
percentage%) of Intensity, Red,
Green, Blue, and White elements of
the LED). Fan Speed, operational
LED junction temperature, power
settings.
Levels
Displays DMX levels for each LED
element (Red, Green, Blue, and
White) and total power.
Normalize Colors
Sub Menu Options Comments
Normalize Colors Adjustment of RGBW Intensities
Allows for fine adjustments to color
intensities for near perfect color
matching.