RAB VAN11 User manual

NOTE: It is recommended that fixture be attached securely by drilling through the back of fixture and attaching to mount-
ing surface (hardware not supplied). When drilling fixture, care must be taken to avoid drilling close to ballast or within
1/4" of sides of fixture. All unused entries must be plugged. Use weatherproof silicone sealant to insure proper seal.
. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION
OF THE PRODUCT AND THE HAZARDS INVOLVED. Fixture should not be used in areas with limited ventilation
or high ambient temperatures. Installation should be done by a qualified electrician.
WIRING
IF SUPPLY WIRES ARE LOCATED WITHIN (3) INCHES OF BALLAST, USE WIRE RATED FOR AT LEAST 150°C.
IF SUPPLY WIRES ARE ROUTED AND SECURED MIN. (3) INCHES
AWAY FROM BALLAST, USE WIRE RATED FOR AT LEAST 90°C.
1. Connect the 120v lead from ballast to the black supply lead.
2. Connect the “com” lead to white supply lead.
3. Fixture ground screw must be connected to supply ground.
Thank you for buying RAB lighting fixtures. Our aim is to design the best quality products so you can get the
job done right. We’d like to hear your comments. Call us at 888-RAB-1000, attention Marketing Department.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
RAB Vandalproof fixtures must be wired in accordance with the National Electrical Code and applicable local codes.
Proper grounding is required for safety
WARNING:Make certain power is OFF before installing or maintaining fixture.
LOCATION
Fixture should be ceiling mounted; but should not be recessed.
MOUNTING
For Fluorescent and Incandescent models
where no housing exists:
1. Remove refractor. .
2. Mount reflector to junction box and/or wall surface with
appropriate hardware.
3. Connect fixture leads to supply leads.
4. Install lamps and replace refractor.
For HID models and Fluorescent models with bronze
ballast housing:
1. Remove refractor and reflector plate.
2. Remove knockouts in housing for desired conduit entrance
(see mounting note below)
3. Connect fixture ballast leads to supply leads with wire nuts.
4. Replace socket mounting plate; install lamp and refractor.
TAMPERPROOF SCREWS
RAB Vandalproof fixtures are shipped with both standard screws and tamperproof screws.
For maximum security, insert tamperproof screws into the refractor and tighten with Center Pin Torx Screwdriver
(catalog #Vandriver, not supplied).
VAN11 & 15 INSTALLATION INSTRUCTIONS
®
(+) LINE BLACK
(–) COMMON WHITE
ER
U
T
XI
F
LP
P
U
S Y

THESE INSTRUCTIONS DO NOT COVER ALL DETAILS OR VARIATIONS IN EQUIPMENT, NOR DO THEY PROVIDE FOR EVERY POSSIBLE CONTINGENCY
TO BE MET IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE.
CLEANING
CAUTION: Be sure power is off. Be sure fixture temperature is cool enough to touch.
Clean reflector and lens with a cloth moistened with non-abrasive glass cleaning solution.
TROUBLESHOOTING CHECKLIST
RE-LAMPING
Disconnect power. Make sure fixture and lamp are cool enough to touch.
1. Loosen screws holding refractor.
2. Remove refractor and install lamp.
3. Close refractor and re-install screws.
CAUTION: Prior to installing, check that the lamp is of proper type and wattage. Observe lamp manufacturer’s
recommendations on lamp operation, ballast type and burning positions.
PHOTOEYE INSTALLATION
A photoeye control may be installed in the field.
1. Remove reflector and socket mounting plate.
2. Remove close-up plug on desired side of fixture.
3. Install Photoeye as per diagram.
REPLACEMENT LAMPS:
HID
MUIDOSERUSSERPHGIHEDILAHLATEM
Wattage Catalog # ANSI Wattage Catalog # ANSI
67S53SPHLttaw53011M05HMLttaw05
86S05SPHLttaw0589M07HMLttaw07
26S07SPHLttaw0709M001HMLttaw001
100 watt LHPS100 S54
150 watt LHPS150 S55
FLUORESCENT Minimum
Wattage Type Catalog # Base Type Start Temp.
26 watt Triple fluorescent LCFL26 G24q-3 base 0°F/ -18°C
32 watt Triple fluorescent LCFL32 G24q-3 base 0°F/ -18°C
42 watt Triple fluorescent LCFL42 G24q-4 base 0°F/ -18°C
VAN11 & 15 INSTALLATION INSTRUCTIONS
120 VOLT LEAD
(+) LINE
RED
(–) COMMON LEAD
WHITE
SUPPLY
BLACK
LIGHT
FIXTURE
PHOTOEYE
1. Proper lamp is installed. Lamp is not faulty.
2. Line voltage at the fixture is proper.
3. Fixture is wired properly.
4. Fixture is grounded properly.
INCANDESCENT
Wattage Type Base Type
120 watt 2-60W A-19 Medium
150 watt 2-75W A-19 Medium
Easy Installation & Pr oduct Help
For fixtures with ballast housing on a seperate back box