Selmo PAD User manual

The PAD is a small reliable heating control
system available for towel radiators.
The device is safe and reliable thanks to a
comprehensive internal protection of the
heating element against overheating or dry
run.
PAD is available in two colours: white
(RAL90 ) and chromed.16
A light ring informs the user when the
heating element is being powered.
PAD can be directly activated through a
switch or it can be remote-controlled via a
control unit that activates the heating
element according to user needs.
The device is available with different sizes
of electric resist : 300W, 600W andor
1000W.
By means of an internal sensor, the
temperature of the towel radiator is
maintained constant
“PAD”
EN
Release 04- 2017August
Electronic control for towel radiators
Comfort technology division
Selmo
Selmo Electronic
Via Pacinotti, 24 - 35030 Rubano www.selmo.it(PD) Italy- Tel [phone], Fax [phone] -
Selmo Electronic
Via Pacinotti, 24 - 35030 Rubano www.selmo.it(PD) Italy- Tel [phone], Fax [phone] -

Technical characteristics
Product
Applications
Insulation class
IP level
Electronic control for towel radiators
Towel radiators
Class I
IP64
Maximum power See table below
Supply voltage 230VAC 50Hz
Warranty 2 years
ABS-VO
CECertification mark
Case
Environmental directives
89/336/EEC
WEEE, RoHS
Electromagnetic compatibility
On/Off light ring indicatorBLUE
Connection to mains 3 Cables (Neutral, Earth, Li e)n
Available colours White (RAL 901 ); Chromed.6
Status light indications
Maximum temp. of the thermal fuse 152°C
Notes for the use :
The device is controlled
externally. It is necessary to
insert a switch or a control unit
between the heating element
and the safety devices.
The manufacturer reserves the
right to make any changes to the
product aimed at improving the
device described in this manual,
at any time, and without prior
warning.
Temperature Limit °C 90 90 100
Power (W) 300 600 1000
Heating lementE
Thread for fastening
on the radiator
Plastic overC
Blue light ring for
On/Off indication
Power cord
“PAD”
EN
Release 04- 2017August
Electronic control for towel radiators
Comfort technology division
Selmo
Selmo Electronic
Via Pacinotti, 24 - 35030 Rubano www.selmo.it(PD) Italy- Tel [phone], Fax [phone] -
Selmo Electronic
Via Pacinotti, 24 - 35030 Rubano www.selmo.it(PD) Italy- Tel [phone], Fax [phone] -

Installation Guide
To be used by installer
•Disconnect the device from power supply before proceeding with installation.
•Protect the device with a 30mA RCD circuit breaker.
•Disconnect the device from power supply before proceeding with installation.
•Protect the device with a 30mA RCD circuit breaker.
NO
SI
(1)
(2)
(3) (4)
1.Lower the plastic cover at the base of the heating element,insert the heating element in the
threaded opening located on the bottom part of the radiator.
2.Securely fasten the electric resistance to the body of the towel radiator with a 22mm wrench.
3.Raise the plastic cover to cover the fixing area.
4.Tilt the radiator as in fig. 3, making sure that the opening on top of the radiator is located on
the highest side. WARNING. Do not lean the radiator on the electronic control!
5.Fill the radiator with the specific liquid.
6.Put the radiator back in vertical position and check the internal level of the liquid (fig. 4).
7.Ensure a proper fastening of the heating element in the radiator.
8.Connect the device to mains and start heating (the top opening of the radiator must remain
open!).
9.Set the maximal temperature and check the level of the internal liquid.
-Due to thermal expansion the liquid could brim over the radiator.
R- emove the exceeding liquid (be careful to avoid burns!) in order to keep the
thermostat dry and avoid the liquid reaching the border.
10.When the level of the liquid stops growing wait for additional 5 minutes then stop heating.
11.If necessary, top up the radiator before the liquid
cools down (keep the temperature of the internal
liquid checked all the time).
12.Close the top opening of the radiator with the
appropriate cap.
13.Hook the radiator to the wall.
14.Connect the device to the mains.
“PAD”
EN
Release 04- 2017August
Electronic control for towel radiators
Comfort technology division
Selmo
Selmo Electronic
Via Pacinotti, 24 - 35030 Rubano www.selmo.it(PD) Italy- Tel [phone], Fax [phone] -
Selmo Electronic
Via Pacinotti, 24 - 35030 Rubano www.selmo.it(PD) Italy- Tel [phone], Fax [phone] -

DISPOSAL
This product may not be treated as ordinary household waste. It has to be disposed in proper waste collection
sites. In case of replacement it shall be returned to .Towelrads
Such an end-of-life treatment of the product will preserve the environment and will reduce consumption of natural
resources.
This symbol applied to the present product indicates the obligation to bring it to a proper waste collection site, in
order to let it be disposed according to 2002/96 / CE (RAEE - WEEE) directives.
Acessory
Accessory 1 : To allow a mixed usage of the
SMART device, connect the T-
piece to the towel radiator, insert
the Pad device into the vertical
manifold of the T-piece and
connect the return line of the
heating circuit to the orthogonal
connector of the T-piece.
Available Colors: White, Chrome.
“PAD”
EN
Release 04- 2017August
Electronic control for towel radiators
Comfort technology division
Selmo
Selmo Electronic
Via Pacinotti, 24 - 35030 Rubano www.selmo.it(PD) Italy- Tel [phone], Fax [phone] -
Selmo Electronic
Via Pacinotti, 24 - 35030 Rubano www.selmo.it(PD) Italy- Tel [phone], Fax [phone] -