Sencor SSB 4450BS User manual

SSB 4450BS
EN User Manual 2.1CH Soundbar with built-in subwoofers
CZ Uživatelská příručka 2.1CH Soundbar svestavěnými subwoofery
SK Používateľská príručka 2.1CH Soundbar so vstavanými subwoofermi
HU Felhasználói kézikönyv 2.1CH Soundbar beépített mélysugárzókkal
PL Podręcznik użytkownika 2.1-kanałowy soundbar z wbudowanymi
subwooferami

2 EN
EN
2023 08/2023
CONGRATULATIONS ON YOUR PURCHASE OF THIS HOME SOUNDBAR. IT FEATURES
ADVANCED DESIGN, MODERN APPEARANCE, RICH SOUND AND EASY OPERATION.
Safety Instructions
This product has been designed with the utmost safety in mind. Use this appliance
only according to the instructions inthis user'smanual. Do not disassemble this device,
otherwise you are exposed to the risk of electric shock. If any damage to this product
occurs, please have this product repaired by aqualified service technician.
Power
Power supply of this unit must be match the serial plate data. Avoid damaging the AC
power cord by pulling, twisting, breaking or pinching it with sharp or heavy objects. To
fully disconnect the unit from the power supply, pull the power cord out of the wall socket.
Placing Objects
Do not place any objects on this device. Damage to the unit may result. Due to operating
vibrations, objects may fall or be damaged.
Heat Source
Keep this unit away from radiant and contact heat sources such as stoves or direct
sunlight.
Water and Humidity
Do not use this unit in humid environment, e.g. in bathrooms, kitchens, etc. Avoid spilling
or contact withwater andother liquids. Do not place vases or pots on the unit.
Cleaning
Prior to cleaning, please disconnect power first. For cleaning, don’t use liquid detergents or
caustic liquids - just clean the unit with asoft cloth.
Connecting Other Devices
Ensure that the power is disconnected before connecting cables from other devices to this
unit. Otherwise damage to the unit or personal injury might occur.
Faults to Be Repaired
If any of the following problems occurs, please disconnect power to the unit and contact
aqualified service technician.
A. Power cord or plug is damaged.
B. Liquids or other foreign objects have penetrated inside the product.
C. the appliance was exposed to rain or water.
D. This unit has fallen on the ground from abig height.
E. Burns can be smelled from the product inside.

EN 3
EN
2023 08/2023
Maintenance
Do not attempt to repair the appliance yourself. By removing the cover, you are exposed
to arisk of electric shock. If needed, please contact aqualified service technician.
Note:
Before using this product, read these instructions carefully and keep it well for future
use.
Unit Location
The soundbar extends the sound capabilities of conventional systems. When used
together with the visual experience, place it as close as possible below the screen,
symmetrical to the centre of the screen. The front speakers should face as directly as
possible towards the listening position. Remember that rich sound means forced vibrations
of the surroundings andthe device itself. Avoid placing any items in the vicinity that
may rattle or vibrate. Keep the gap between the soundbar and the screen at least afew
millimetres.
Two types of placement are possible: on apad and mounted on awall.
Placing the Unit on the Pad
The soundbar pad must be straight andsolid. The size of the feet is optimised for the
correct sound of the subwoofers, do not cover them or put any other objects under the
soundbar, whether soft (textiles) or hard.
Placing the Unit on the Wall
Caution:
the included installation elements are suitable for solid walls with reliable contact
of dowels. If these elements are not sufficient, replace them with other, separately
purchased ones, which will secure the fixed location. Wall mounting is more
difficult to install. It is essential that the anchorage of the load-bearing screws is
absolutely solid. Please consultan expert. Do not place any objects on the fixed
unit.

4 EN
EN
2023 08/2023
Remote Control and Battery
Safety Precautions for Batteries
Always use batteries properly. Pay attention to the correct polarity (plus and minus) of
the inserted batteries. Use non-rechargeable batteries. Do not recharge non-rechargeable
batteries, disassemble the batteries and do not throw them in fire. Do not use different
types of batteries together or new batteries with old ones. Do not leave damaged or
discharged batteries in the remote. If the remote control is not to be used for an extended
period of time, remove the batteries to prevent it from damage by electrolyte leakage.
If the remote control is not working correctly or its operational range is reduced, change
all batteries for new ones. If electrolyte leakage occurs, first clean the battery case, then
replace the batteries with new ones.
Functions and Specifications
• Length: 37‘‘
• Supports Bluetooth 5.3, range 10 m.
• 2.1CH Soundbar with built-in subwoofers
• Digital volume control
• Fully functional remote control
• HDMI ARC
• Optical audio input
• Aux In (3.5 mm audio input)
• Playback from USB
Package Contents:
• Soundbar
• Remote control
• Power cable, 1 pc
• Accessories for wall mounting
• User guide
• 3.5 mm cable for RCA 1 pc
• Batteries for remote control

EN 5
EN
2023 08/2023
Connection Points:
1. Power port AC 100–240 V: Connecting to themains voltage.
2. AUX input: Auxiliary audio input from MP3/phone/set-top box device.
3. HDMI ARC
4. Optical Input
5. USB: Audio input from USB memory device.
Buttons on the Side of the Appliance:
6. : Press to turn the soundbar on/off, then press to switch to different audio sources.
7. : Press to reduce the volume
8. : Press to increase the volume
9. : Long press to disconnect the Bluetooth function, short press to play/pause.

6 EN
EN
2023 08/2023
Remote Control
Functions and Controls
1. : Power on/off
2. : Switching inputs (Bluetooth, Aux, Optical, HDMI, USB)
3. VOL+: Press to increase the sound volume
4. : Previous track (only works in USB andBT mode).
5. MUSIC: Select Music mode.
6. MOVIE: Select Movie mode.
7. Bass+: Select Bass+: Press to increase the bass effect.
8. 3D: Select the 3D EQ effect.
9. Bass-: Press to reduce the bass effect.
10. : Mute mode
11. Reset: Hold down the button for more than 3 seconds to restore the factory default
settings.
12. : Short press for playback/pause (only works in USB andBT mode). Long press to
disconnect Bluetooth.
13. : Next track (only works in USB andBT mode).
14. VOL-: Press to decrease the sound volume.
15. NEWS: Select the Messages mode.
16. Treble+: Press to increase the effect of the high tones.
17. Treble-: Press to reduce the effect of the high tones

EN 7
EN
2023 08/2023
Remote Control Instructions
Use the controller up to amaximum distance of about 7 m. Do not use the remote control
within the reach of an intense light source such as sunlight. Point the remote control at
the sensor (display). Avoid shocks, ingress of water, liquids andmoisture. Do not allow
pets to play with theremote control. Do not disassemble it.
Turning the Power On and Off
1. Plug the power cord into one side of the AC IN on the soundbar and the other side
into an AC outlet. When the soundbar is connected to the main power outlet, the unit
will be in standby mode with the LED display “--” illuminated.
2. Turn on the soundbar by briefly pressing the button on the soundbar or on the remote
control, then it will automatically enter the Bluetooth mode.
3. Press and hold the button on the soundbar or remote control for 2 seconds to turn the
unit off, and if you want to turn the unit off completely, unplug the main plug from the
main power outlet.
Mode Selection
MOVIE – mode optimised for movies anddramatic arts. It slightly widens the stereo base
and slightly harmonically emphasises the speech band.
MUSIC – music playback mode. It purely transmits stereo channels without harmonic
andspatial adjustment.
NEWS – amode optimised for the spoken word. Significantly reduces the noise andnoise
frequency band for the best speech intelligibility.
3D – space emphasis mode. It can be switched on or off independently of the above
modes. Indication on the display “3d”.
Selection of Inputs
Press the “ ” button on the soundbar or press the “MODE” button on the remote control
to select BT, AUX, OPTICAL, HDMI ARC. The selected input is briefly shown by the
display text.
Sound Playback via BT Connection
1. Turn on the soundbar, it will automatically switch to the Bluetooth mode, or if it
is inanother mode, short press the “ ” button on the soundbar or “MODE” on
the remote control to switch it to the Bluetooth mode. The LED display will show
aflashing “bt”.
2. Activate the pairing function on your phone or other compatible device andchoose
“SSB4450BS” using the BT connection.
3. After successful pairing, the small “bt” symbol will permanently appear on the LED
display. You can then play music on the soundbar from the phone or other compatible
device that you have paired.

8 EN
EN
2023 08/2023
4. Use the volume buttons on the soundbar or on the remote control to adjust the
volume according to your requirements.
5. If you wish, you can change the sound settings using the relevant buttons on the
remote control.
Note:
This soundbar has the memory of the last function used; after being turned on again, it
will use the last mode again before being turned off.
Aux Input (3.5 mm)
Requires 3.5 mm audio cable.
1. Connect a3.5 mm audio cable to the Aux In input on the unit andto the audio
output/headphone jack on the audio device.
2. Turn on the soundbar andpress the “ ” button on the soundbar or use the “MODE”
switch to select the Aux in mode. The LED display shows AUX.
3. Use the controls on the connected device to select andplay the sound. Make sure
that the volume on the connected device is audible at the start of playback.
Connecting the TV via HDMI Cable (Not Included) HDMI
ARC
HDMI offers excellent sound andpicture quality. This is the easiest way to connect
multimedia devices to thesoundbar.
1. Press the “ ” button on the soundbar or the “MODE” button on the remote control to
select the HDMI mode.
2. Use an HDMI cable (not included) to connect to aTV with an HDMI ARC port, making
sure the HDMI ARC function is enabled on the TV and the digital output is set to
PCM.
3. Use the volume buttons on the TV remote to change the volume of the Soundbar.
Optical Input
Requires an audio source withan optical audio output and adigital optical audio cable
(not included).
1. Use adigital optical audio cable to connect the optical input on the soundbar to the
optical output on the audio source (TV, amplifier, etc.).
2. Turn on the soundbar and press the Optical button on the remote control or Source on
the soundbar to select Optical mode. The LED display shows “OPT”.
3. On the connected audio source (TV, amplifier, etc.), make sure that the sound setting
is set to PCM or Optical Audio.
4. The sound played through the connected sound source (TV, amplifier, etc.) should now
be heard through the speaker.

EN 9
EN
2023 08/2023
Important Tips for Optical Sound:
• Use the correct optical audio cable andmake sure that it is firmly inserted in the
sockets of thepower supply and the soundbar.
• The optical audio output is activated from the audio source (red light should be visible
on the optical socket). Inthe source settings menu, it can be marked as S/PDIF.
• The optical output of the source should be set to PCM output, not Dolby Digital.
USB Playback
Briefly press the button to turn on the soundbar, insert the USB into the USB port and
the soundbar will start playing music on the USB drive, briefly press “ ” to play/pause
the music. MP3 music is played from theroot directory of the inserted USB disc.
Troubleshooting
Problems Solution
Bluetooth connection pairing
cannot be completed
Soundbar is still paired withthe previous mobile
device. Disable Bluetooth on the previous mobile
device. Only then search again for available devices
and pair again with the SSB 4450BS.
Bluetooth playback volume is
low
Check the volume settings on both the soundbar and
the mobile device and set both to an appropriate
value.
Short Bluetooth connection
distance
There is abarrier between mobile devices and the
Bluetooth device. Remove obstacles.
The Bluetooth connection is not
stable
Remove obstacles between mobile devices and
thesoundbar
Shorten the distance between the soundbar
andmobile devices.
Silent playback when connected
via Bluetooth
Check the Bluetooth volume setting on the mobile
device.

10 EN
EN
2023 08/2023
Specifications
Product name SSB 4450BS
RMS output power 25W*2+25W*2 RMS
AC/DC adapter 100–240V~50/60Hz
Speaker frequency 50Hz–15KHz
Included Soundbar, remote control, AC power cord, 3.5 mm cable
to RCA, user guide, wall mounting screws
Weight 3.5 kg
Dimensions Soundbar: 960*131*71 mm
Bluetooth Version 5.3
 Maximum Transmitter Power 100mW @ 2.4GHz–2.4835GHz
 Codec SBC
 Profiles A2DP/AVRCP

EN 11
EN
2023 08/2023
INSTRUCTIONS AND INFORMATION ON THE DISPOSAL OF DISCARDED
PACKAGING MATERIALS
Take the packaging material to acollection yard for disposal.
DISPOSAL OF DISCARDED ELECTRICAL AND ELECTRONIC
EQUIPMENT
This symbol on the product, accessory or packaging indicates that the product
must not be treated as normal household waste. Please dispose of this product
in acollection yard designated for the recycling of electrical and electronic
equipment. In some EU countries or in some European countries, you can
return your products to your local retailer when you buy an equivalent new
product. By disposing of this product properly, you are helping to protect
valuable natural resources and prevent the potential negative environmental
and human health impacts that could result from improper waste disposal.
Please contact your local authority or the nearest waste collection yard for
further details. Improper disposal of this type of waste may be subject to alegal
fine.
For companies in the European Union
If you need to dispose of electrical or electronic equipment, ask your dealer or supplier for
the necessary information.
Disposal in countries outside the European Union
If you wish to dispose of this product, please ask the Ministry or your dealer for the
necessary information on the correct disposal method.
The product meets the EU requirements.
FAST ČR, a.s. hereby declares that the radio device type SSB 4450BS conforms to the
2014/53/EU directive.
For full version of the EU declaration of conformity, please refer to
www.sencor.eu website.
Text, design and technical data are subject to change without notice and we reserve the
right to make changes.
The original version is in Czech.
Manufacturer’saddress: FAST ČR, a.s., USanitasu 1621, Říčany CZ-251 01

12 EN
EN
2023 08/2023
EN Warranty conditions
Warranty card is not apart of the device packaging.
This product is warranted for the period of 24 months from the date of purchase to the end-user. Warranty
is limited to the following conditions. Warranty is referred only to the customer goods using for common
domestic use. The claim for service can be applied either at dealer’sshop where the product was bought, or
at below mentioned authorized service shops. The end-user is obligated to set up aclaim immediately when
the defects appeared but only till the end of warranty period. The end user is obligated to cooperate to certify
the claiming defects. Only completed and clean (according to hygienic standards) product will be accepted.
In case of eligible warranty claim the warranty period will be prolonged by the period from the date of claim
application till the date of taking over the product by end-user, or the date the end-user is obligated to take it
over. To obtain the service under this warranty, end-user is obligated to certify his claim with duly completed
following documents: receipt, certificate of warranty, certificate of installation.
This warranty is void especially if apply as follows:
Defects which were put on sale.
Wear-out or damage caused by common use.
The product was damaged by unprofessional or wrong installation, used in contrary to the applicable
instruction manual, used in contrary to legal enactment and common process of use or used for another
purpose which has been designed for.
The product was damaged by uncared-for or insufficient maintenance.
The product was damaged by dirt, accident of force majeure (natural disaster, fire, and flood).
Defects on functionality caused by low duality of signal, electromagnetic field interference etc.
The product was mechanically damaged (e.g. broken button, fall).
Damage caused by use of unsuitable media, fillings, expendable supplies (batteries) or by unsuitable
working conditions (e.g. high temperatures, high humidity, quakes).
Repair, modification or other failure action to the product by unauthorized person.
End-user did not prove enough his right to claim (time and place of purchase).
Data on presented documents differs from data on products.
Cases when the claiming product cannot be indentified according to the presented documents (e.g. the
serial number or the warranty seal has been damaged).
Manufacturer:
FAST ČR, a.s., U Sanitasu 1621, Říčany 251 01, Czech Republic
Visit www.sencor.com for detailed information about authorized service centers.
The original version of the instructions is in the Czech language, other language versions are made by the
appropriate translation.

FAST ČR, a.s., USanitasu 1621, Říčany CZ-251 01