Sendum PT300D User manual

PT300D QuickStart Guide
Part Number BFA10083 - Verizon
DPB00007 -- 1 --
Welcome
Thanks for choosing the Sendum PT300D
as your Package Tracking solution! The
purpose of this Quick Start Guide is to help
you get your system up and running as
quickly as possible.
Introduction
Your PT300D device (model BFA10083) has
been configured for use with Verizon wireless
service.
Step 1: Get Familiar
PT300D Trackers come in many different
varieties and configurations. Depending on
what you ordered, you may have some, or all,
of the components listed in “Figure 1 - PT300D
Component List”.
To get started working with your new PT300D,
at a minimum you will need the PT300D
Command Module complete with one of the
following:
• a Basic Sensor Pack with the AC Adapter
and Data Cable
• an Advanced Sensor Pack with the AC
Adapter and Data Cable, OR
• the Accessory Pack, complete with the 10k
mAh Battery Pack and Battery Charger
PT300D
Command Module
AC Adapter
P/N: BFA10069
Data Cable
P/N: MCA10017
Accessory Pack
P/N: BFA10077
P/N: BFA10095
Battery Charger
for 10k mAh Battery
P/N: BFA10179
10k mAh
Battery Pack
Advanced Sensor Pack
P/N: BFA10063
Basic Sensor Pack
P/N: BFA10062
Figure 1 - PT300D Component List

PT300D QuickStart Guide
Part Number BFA10083 - Verizon
-- 2 --
Step 2: Charging
Just like with any new mobile device, you’ll
need to charge your battery before you can
start using it. This is normally an overnight
process, or at least six hours. To do this:
• If you are using either the Basic Sensor
Pack or the Advanced Sensor Pack, you can
charge it by connecting it to the AC Adapter
and then plugging the adapter into any
standard electrical receptacle (see “Figure
3 - Charging up a Sensor Pack”.)
• If you are using an Accessory Pack with
the 10K mAh Battery Pack, the process is
similar. Just connect the battery to the AC
adapter and then plug the adapter into
the electrical receptacle (see “Figure 4 -
Charging the 10k mAh Battery Pack”.)
Step 3: Airtime Account
In order for your device to operate and
communicate properly, you need to have a
machine-to-machine (M2M) airtime account
set up. If you don’t have an account, please
contact your wireless provider and provide
them the ‘Device Identifier’ number of your
device.
The Device Identifier is device-specific
serial number found on the back of
the PT300D Command Module (see
“Figure 2 - Locating the PT300D
Device ID”). This identifier is also
known as ESN, MEID, or IMEI.
What’s needed is an M2M airtime account with
SMS texting capability. Typical data plan sizes
are 1 MB, 5 MB, and 10 MB (with the 5 MB
plan being a popular choice).
Device Identifier
PT300D Command
Module
Part Number
Figure 2 - Locating the PT300D Device ID
Sensor Pack
AC Adapter
PT USB Cable
Figure 3 - Charging up a Sensor Pack
Figure 4 - Charging the 10k mAh Battery Pack

PT300D QuickStart Guide
Part Number BFA10083 - Verizon
-- 3 --
Step 4 - Provision
Your Verizon service needs to be provisioned
before you can use your device.
Provisioning is a one-time, secure,
and anonymous process in which
your PT300D links with both your
mobile network and your software
web application to communicate
registration information and initiate
operation of the device.
Provisioning for Verizon
The process for provisioning your device for
Verizon service is simple:
1) Turn on your PT300D (see “1. Turning
on your PT300D” on page 5). This
step initiates communication with both
your wireless network and with Sendum.
2) While communicating, both the Network
and Battery LEDs should go on and off
periodically. See “3. LED Lights and
Status Button” on page 6
3) When complete (about a minute), both
Network and Battery lights will go solid
green (indicating success).
4) Unplug the PT300D Command Module
from your pack. This ensures the device
is power-cycled, a necessary step before
the device can be operational.
5) The final step to provisioning is to make
at least one configuration change for
your device. Please refer to “Step 5 -
Web Access” and “Step 6 - Configure”.
You can also learn the Provisioning
process by watching our video at
www.sendum.com/pt300av

PT300D QuickStart Guide
Part Number BFA10083 - Verizon
-- 4 --
Step 5 - Web Access
1) Once you have an airtime account in
place and with your device successfully
provisioned, please open up your web
browser and go to Sendum’s web portal
(called Findum™) at
findum.sendum.com
2) If you already have a Findum account
in place and you ordered your new
product with the same email address,
your new PT300D device will have been
automatically added to your existing
account. Just log in using that email
address and your existing password.
3) If you are new to Findum, a new Findum
account would have been created for
you as a part of the purchase process.
The username for this new account is the
email address that you used, or specified,
during purchasing. To obtain a password
for this account, please go to findum.
sendum.com and click the “Forgot your
Password” link. Then just log into Findum
using your email address and your new
password. For a demo of this process,
please visit
www.sendum.com/getpassword
Step 6 - Configure
For complete information and tutorials on how
to use your PT300D trackers within Findum,
please refer to the detailed Findum Help Guide.
Once you are logged into Findum, the guide is
accessible by clicking the Help link in the upper
left hand corner of any Findum page.
Note that when first get your new tracker, you
will have to configure your device with an
Assisted Location, Autonomous Location, or
Sensor Reports interval before the device will
report data.
To access the Device Configuration page within
Findum, click the Devices menu item on the
left side, choose your device, then click the
Configuration tab.
Step 7 - View your Data
Once your PT300D has been configured, you
will be able to track location, gather data, and
view reports.
Figure 5 - Viewing Device Data in Findum

PT300D QuickStart Guide
Part Number BFA10083 - Verizon
-- 5 --
Sensor Pack
AC Adapter
Data Cable
PT300D
Command
Module
PT300D
Command
Module
Sensor Pack with
sufficient battery charge
PT300D
Command
Module
Accessory Pack
10K mAh Battery Pack
with sucient charge
Figure 6 - Turning the PT300D on by connecting it
with a charged Sensor Pack
Figure 7 - Turning the PT300D on by connecting it
with a Sensor Pack being charged
Figure 8 - Turning the PT300D on by connecting it
with an Accessory Pack and a charged
10K mAH Battery Pack
Appendix
1. Turning on your PT300D
You can turn on (i.e. power up) your PT300D by
connecting the command module to a Sensor
or Accessory Pack.
To make the connection, simply push the
command module into the pack until you hear
a click sound. Once connected, ensure the
Charger LED is ON. The color will be either red
or green.
When connecting any type of Sensor
or Accessory Pack to the Command
Module, always make sure the
connection is solid and that you hear
the confirming “Click” sound.

PT300D QuickStart Guide
Part Number BFA10083 - Verizon
Sendum Wireless Corporation
4500 Beedie Street, Burnaby, BC V5J 5L2
www.sendum.com
-- 6 --
2. Turning off your PT300D
To turn off (or power down) your PT300D,
simply unplug the PT300D Command Module
from your Sensor or Accessory Pack.
To do this, squeeze the two tabs on the side of
the command module, then pull the module
straight out of the pack.
3. LED Lights and Status Button
SENDUM
Status
Button
Charger
Battery
Network
LED Indicators:
PT300/
PT300D
Sensor or
Accessory
Pack
4. LED Light Indications
LED Status Description
Network
Green Device in carrier coverage
area
Green
(Blinking)
Device is in Aircraft
Transmission Suppression
Mode
Red Device out of carrier
coverage area
Red
(Blinking)
Device is in Coverage Sleep
Mode
Battery
Green Sensor Pack charge level
near full (80%+)
Red Sensor Pack needs
recharging
Red
(Blinking)
Sensor Pack charge level
good (approximately
20-80%)
Charger
Red Sensor Pack is charging
Green Sensor Pack charging is
complete