Senect VIS-LED-AK-SC User manual

Alarm lamp with horn
MANUAL

Type
2
Type
Product name:
SENECT®Alarm lamp with horn
Type:
VIS-LED-AK-SC
Art.-No.:
3210
Producer:
SENECT GmbH & Co. KG
An 44 –Nr. 11
76829 Landau / Germany
Important note:
Please read this manual carefully and store it so that you can use
it later. Read the warning and safety notes attentive.
More information and latest software releases or documents can
be downloaded from:
www.senect.de
Further information, application descriptions and answers to
frequently asked questions can be also found on the SENECT
Forum:
http://forum.senect.de
© SENECT GmbH & Co. KG - FW 00.90

Table of contents
3
Table of contents
Type............................................................................................... 2
Table of contents........................................................................... 3
Used symbols and wording ........................................................... 4
General Security Notes.................................................................. 5
Intended use.................................................................................. 6
Getting started .............................................................................. 6
Scope of delivery ....................................................................... 6
Note........................................................................................... 6
Installation and start-up............................................................ 7
Tone selection table .................................................................... 10
Technical data ............................................................................. 12
Information about the correct disposal ...................................... 13
Guarantee.................................................................................... 13

Used symbols and wording
4
Used symbols and wording
DANGER!
Warning of life threatening
dangers.
WARNING!
Warning of possible life
threatening and / or severe
irreversible injuries.
ATTENTION!
Warning of possible medium
or slight injury.
ATTENTION!
Follow the notes to avoid
damage of equipment
NOTE!
Further information for the
use of the device!
ATTENTION!
Warning of electrical shock.

General Security Notes
5
General Security Notes
The alarm lamp is an electric device designed for visually and
acoustically alarming the user of the SENECT control units in
case of the occurrence of a user-defined alarm.
Since it is an electric product the common
prerequisites for a safe instrument usage must be
fulfilled. Ensure that all cables are installed safely
so that no obstacles for persons are built and all. Mount all
cables and electric devices protected against direct
environmental impacts like overheating by direct sunlight
and water. Even if the product is protected against spray
water, the product´s lifetime will be elongated, if it is
mounted on a protected place.
The operating temperature of the device must be between
minus 25°C and plus75°C.
The device is designed to be operated by professional users.
It can be also operated by children over the age of 8 years
and persons with limited physical, sensorial or cognitive
ability, if they are supervised, trained in the operation of the
device, able to operate the device safely and if they
understand potential risks resulting from the operation. It is
for children or persons with limited physical, sensorial or

Intended use
6
cognitive ability not allowed to perform any maintenance
works.
Please store this manual. We suggest the storage a copy of
the manual in the vicinity of the device.
Technical and optical changes of this manual are subject to
alterations.
Intended use
The alarm lamp is an electric device designed for visually and
acoustically alarming the user of the SENECT control units in
case of the occurrence of a user-defined alarm.
The alarm lamp is developed for the use in industrial
aquaculture applications.
Getting started
Scope of delivery
o1 x Alarm lamp with horn
o1 x Manual
Note
Please check directly after delivery, that the
package is not destroyed or damaged or was
opened before. Please check also, that all parts as

Getting started
7
listed above are included. If anything is missing or broken,
please contact us as soon as possible within 14 days.
Unfortunately, we cannot accept later information of
damage, which happened during the transport.
Installation and start-up
Mount the alarm lamp at a place in the vicinity of
your control unit where you can see it best.
To mount the alarm lamp, the upper part of the
housing must be opened by rotating this part against the
bottom part.
1. Loosen calbe gland
2. Remove screw
3. Open by rotating

Getting started
8
In the bottom part, there are several deepening where
mounting holes can be drilled. Mount the bottom part with
screws through these holes on the desired location.
You can now also select the desired tone type and adjust the
loudness.
Close the housing, tighten the cable gland and insert back the
screw.
Connect the green plug of the alarm lamp to one of the
SENECT controllers actuator output ports („OUT“).
Select the function „Alarm“ for this output port in the menu
of the controller. Now, the alarm lamp will be switched on in
case the controller detects an alarm. You can define the
alarm setting at each sensor under „Alarm thresholds“.
Selecting the tone
Loudness control

Getting started
9
Getting started –short version
1. Open housing by removing the screw, loosening the
cable gland and rotation of the two housing parts.
2. Drill holes through the bottom part.
3. Mount the bottom part.
4. Select tone type and loudness.
5. Close the housing.
6. Connect cable to controller (actuator plug „OUT“).
7. Select the function „Alarm“ this ouput port.
Now, the alarm lamp is ready to be used.

Tone selection table
10
Tone selection table
DIP-
Positions
Description
Frequency
[Hz]
Time
Pattern
Application
000000
Up- and
downswelling
150 to
1000 to
150
10 s –40 s
–10 s
Hoechst
000001
alternating
800 & 970
2 Hz
BS Fire
000010
Upswing
800 to
970
7 Hz
BS Fire
000011
Upswing
800 to
970
1 Hz
BS Fire
000100
Permanent
sound
2850
Steady
000101
Upswing
2400 to
2850
7 Hz
000110
Upswing
2400 to
2850
1 Hz
000111
Upswing
300to
1200
3 s
increasing,
0.5 s
silence,
repetition
Netherlands
Fire
(NEN2575)
001000
Downswelling
1200 to
500
1 Hz
German
Fire (DIN
33404)
001001
Alternating
2400 &
2850
2 Hz
001010
Interrupted
970
0.5 Hz
001011
Alternating
800 & 970
1 Hz
001100
Interrupted
2850
0.5 Hz
001101
Interrupted
970
0.8 Hz
001110
Permanent
sound
970
Steady
PFEER toxic
gas
001111
Alternating
554 & 440
100 ms –
400 ms
France Fire
(NFS 32-
001)
010000
Interrupted
660
3.3 Hz
Sweden Air
Raid

Tone selection table
11
010001
Interrupted
660
0.28 Hz
Sweden
local
warning
010010
Interrupted
660
0.05 Hz
Sweden
pre-mess
010011
Permanent
sound
660
Steady
Sweden all
clear
010100
Alternating
554 & 440
0.5 Hz
Sweden
turn out
010101
Interrupted
660
1 Hz
Sweden
general
010110
Interrupted
2850
4 Hz
Pelican
crossing
010111
Upswing
800 to
970
50 Hz
BS fire
011000
Upswing
2400 to
2850
50 Hz
011001
Interrupted
970
3 x 500 ms
pulse, 1.5
s pause
ISO 8021
011010
Interrupted
2850
3 x 500 ms
pulse, 1.5
s pause
ISO 8021
011011
Permanent
sound
4000
Steady
ISO 8021
011100
Alternating
800 & 970
2 Hz
BS Fire
011101
Alternating
990 & 650
2 Hz
BS Fire
011110
Alternating
510 & 610
2 Hz
BS Fire
011111
Upswing
300 to
1200
1 Hz
100000
Permanent
sound
4000
Steady
BS Fire
100001
Permanent
sound
990
Steady
100010
Interrupted
990
1 Hz
100011
Permanent
sound
510
Steady
100100
Interrupted
510
1 Hz
100101
Permanent
sound
850
Steady

Technical data
12
Technical data
Dimensions housing:
Ø 90 x 97 / 108 mm
Material:
ABS
Cable length:
5 m
Voltage:
24 V DC
Power consumption:
1,2 W
Temperature range:
-25°C to +70°C
Ingress protection:
IP65

Information about the correct disposal
13
Information about the correct disposal
Your device is well packed at delivery. Please
dispose the packaging material accordingly to the
regulations in your country.
Do not throw the product in the casual litter bin. Make sure
you are informed about the local disposal regulations and
dispose your product accordingly. Alternatively, you can also
send the product back to the producer.
The SENECT GmbH & Co. KG is member of the Stiftung
Elektro-Altgeräte Register and the products are registered
(WEEE-Reg.-Nr.: DE37193510).
Guarantee
Please check at delivery of your device, that all
parts are delivered completely and that they
function correctly. In case of any claims, contact us
immediately per email or phone ([email protected] or +49-
6341 - 95 95 210). Please describe your claim as detailed as
possible so that we can provide a solution as fast as possible.
The product has a guarantee of 1 year and a warranty of 2
years. Furthermore, the § 377 HBG (German law) is valid.