Sensaphone IMS-4010E User manual

IMS–4000™
SENSAPHONE®
LIT-0172 SENSAPHONE®
IMS-4010E
Dry Contact Node
User’s Manual

2
Every effort has been made to ensure that the information in this document is complete, accurate
and up-to-date. Sensaphone assumes no responsibility for the results of errors beyond its control.
Sensaphone also cannot guarantee that changes in equipment made by other manufacturers, and referred
to in this manual, will not affect the applicability of the information in this manual.
Copyright © 2011 by Sensaphone
First Edition, version 1.2, January 2020
Written and produced by Sensaphone
Please address comments on this publication to:
Sensaphone
901 Tryens Road
Aston, PA 19014
Sensaphone is a registered trademark of Phonetics, Inc.

3
Important Safety Instructions
Your IMS-4010E has been carefully designed to give you years of safe, reliable performance. As with all electrical
equipment, however, there are a few basic precautions you should take to avoid hurting yourself or damaging the
unit:
• Read the installation and operating instructions in this manual carefully. Be sure to save it for future refer-
ence.
• Read and follow all warning and instruction labels on the product itself.
• To protect the IMS-4010E from overheating, make sure all openings on the unit are not blocked. Do not place on
or near a heat source, such as a radiator or heat register.
• Do not use your IMS-4010E near water, or spill liquid of any kind into it.
• Be certain that your power source matches the rating in the specications of this manual. If you’re not sure of the
type of power supply to your facility, consult your dealer or local power company.
• Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by
persons walking on it.
• Do not overload wall outlets and extension cords, as this can result in the risk of re or electric shock.
• Never push objects of any kind into this product through ventilation holes as they may touch dangerous voltage
points or short out parts that could result in a risk of re or electric shock.
• To reduce the risk of electric shock, do not disassemble this product, but return it to Sensaphone Customer Ser-
vice, or another approved repair facility, when any service or repair work is required. Opening or removing covers
may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the unit
is subsequently used.
• If anything happens that indicates that your IMS-4010E is not working properly or has been damaged, unplug it
immediately and follow the procedures in the manual for having it serviced. Return the unit for servicing under
the following conditions:
1. e power cord or plug is frayed or damaged.
2. Liquid has been spilled into the product or it has been exposed to water.
3. e unit has been dropped, or the enclosure is damaged.
4. e unit doesn’t function normally when you’re following the operating instructions.
• To reduce the risk of re or injury to persons, read and follow these instructions:
Use only the specified type and size batteries.
Do not dispose of the batteries in a fire. The cell may explode. Check with local codes for possible special disposal
instructions.
Do not open or mutilate batteries. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may
be toxic if swallowed.
Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, brace-
lets, and keys. The battery or conductor may overheat and cause burns.
Remove main power before replacing the batteries.

4
3 YEAR LIMITED WARRANTY
PLEASE READ THIS WARRANTY CAREFULLY BEFORE USING THE PRODUCT.
THIS LIMITED WARRANTY CONTAINS SENSAPHONE’S STANDARD TERMS AND CONDITIONS. WHERE
PERMITTED BY THE APPLICABLE LAW, BY KEEPING YOUR SENSAPHONE PRODUCT BEYOND THIRTY (30) DAYS
AFTER THE DATE OF DELIVERY, YOU FULLY ACCEPT THE TERMS AND CONDITIONS SET FORTH IN THIS LIMITED
WARRANTY.
IN ADDITION, WHERE PERMITTED BY THE APPLICABLE LAW, YOUR INSTALLATION AND/OR USE OF THE
PRODUCT CONSTITUTES FULL ACCEPTANCE OF THE TERMS AND CONDITIONS OF THIS LIMITED WARRANTY
(HEREINAFTER REFERRED TO AS “LIMITED WARRANTY OR WARRANTY”). IF YOU DO NOT AGREE TO THE TERMS
AND CONDITIONS OF THIS WARRANTY, INCLUDING ANY LIMITATIONS OF WARRANTY, INDEMNIFICATION
TERMS OR LIMITATION OF LIABILITY, THEN YOU SHOULD NOT USE THE PRODUCT AND SHOULD RETURN IT
TO THE SELLER FOR A REFUND OF THE PURCHASE PRICE. THE LAW MAY VARY BY JURISDICTION AS TO THE
APPLICABILITY OF YOUR INSTALLATION OR USE ACTUALLY CONSTITUTING ACCEPTANCE OF THE TERMS AND
CONDITIONS HEREIN AND AS TO THE APPLICABILITY OF ANY LIMITATION OF WARRANTY, INDEMNIFICATION
TERMS OR LIMITATIONS OF LIABILITY.
1. WARRANTOR: In this Warranty, Warrantor shall mean “Dealer, Distributor, and/or Manufacturer.”
2. ELEMENTS OF WARRANTY: This Product is warranted to be free from defects in materials and craftsmanship with only the
limitations and exclusions set out below.
3. WARRANTY AND REMEDY: Three-Year Warranty — In the event that the Product does not conform to this warranty at any
time during the time of three years from original purchase, warrantor will repair the defect and return it to you at no charge.
This warranty shall terminate and be of no further effect at the time the product is: (1) damaged by extraneous cause such as
fire, water, lightning, etc. or not maintained as reasonable and necessary; or (2) modified; or (3) improperly installed; or (4) mis-
used; or (5) repaired or serviced by someone other than Warrantors’ authorized personnel or someone expressly authorized by
Warrantor’s to make such service or repairs; (6) used in a manner or purpose for which the product was not intended; or (7) sold
by original purchaser.
LIMITED WARRANTY, LIMITATION OF DAMAGES AND DISCLAIMER OF LIABILITY FOR DAMAGES: THE
WARRANTOR’S OBLIGATION UNDER THIS WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT OF THE
PRODUCT, AT THE WARRANTOR’S OPTION AS TO REPAIR OR REPLACEMENT. IN NO EVENT SHALL WARRANTORS
BE LIABLE OR RESPONSIBLE FOR PAYMENT OF ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL AND/OR PUNITIVE
DAMAGES OF ANY KIND, INCLUDING BUT NOT LIMITED TO ANY LABOR COSTS, PRODUCT COSTS, LOST
REVENUE, BUSINESS INTERRUTPION LOSSES, LOST PROFITS, LOSS OF BUSINESS, LOSS OF DATA OR INFORMATION,
OR FINANCIAL LOSS, FOR CLAIMS OF ANY NATURE, INCLUDING BUT NOT LIMITED TO CLAIMS IN CONTRACT,
BREACH OF WARRANTY OR TORT, AND WHETHER OR NOT CAUSED BY WARRANTORS’ NEGLIGENCE. IN
THE EVENT THAT IT IS DETERMINED IN ANY ADJUDICATION THAT THE LIMITED WARRANTIES OF REPAIR
OR REPLACEMENT ARE INAPPLICABLE, THEN THE PURCHASER’S SOLE REMEDY SHALL BE PAYMENT TO THE
PURCHASER OF THE ORIGINAL COST OF THE PRODUCT, AND IN NO EVENT SHALL WARRANTORS BE LIABLE OR
RESPONSIBLE FOR PAYMENT OF ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL AND/OR PUNITIVE DAMAGES
OF ANY KIND, INCLUDING BUT NOT LIMITED TO ANY LOST REVENUE, BUSINESS INTERRUTPION LOSSES, LOST
PROFITS, LOSS OF BUSINESS, LOSS OF DATA OR INFORMATION, OR FINANCIAL LOSS, FOR CLAIMS OF ANY
NATURE, INCLUDING BUT NOT LIMITED TO CLAIMS IN CONTRACT, BREACH OF WARRANTY OR TORT, AND
WHETHER OR NOT CAUSED BY WARRANTORS’ NEGLIGENCE.
WITHOUT WAIVING ANY PROVISION IN THIS LIMITED WARRANTY, IF A CIRCUMSTANCE ARISES WHERE
WARRANTORS ARE FOUND TO BE LIABLE FOR ANY LOSS OR DAMAGE ARISING OUT OF MISTAKES, NEGLIGENCE,
OMISSIONS, INTERRUPTIONS, DELAYS, ERRORS OR DEFECTS IN WARRANTORS’ PRODUCTS OR SERVICES, SUCH
LIABILITY SHALL NOT EXCEED THE TOTAL AMOUNT PAID BY THE CUSTOMER FOR WARRANTORS’ PRODUCT
AND SERVICES OR $250.00, WHICHEVER IS GREATER. YOU HEREBY RELEASE WARRANTORS FROM ANY AND ALL
OBLIGATIONS, LIABILITIES AND CLAIMS IN EXCESS OF THIS LIMITATION.
INDEMNIFICATION AND COVENANT NOT TO SUE: YOU WILL INDEMNIFY, DEFEND AND HOLD HARMLESS
WARRANTORS, THEIR OWNERS, DIRECTORS, OFFICERS, EMPLOYEES, AGENTS, SUPPLIERS OR AFFILIATED
COMPANIES, AGAINST ANY AND ALL CLAIMS, DEMANDS OR ACTIONS BASED UPON ANY LOSSES, LIABILITIES,
DAMAGES OR COSTS, INCLUDING BUT NOT LIMITED TO DAMAGES THAT ARE DIRECT OR INDIRECT,
INCIDENTAL, SPECIAL OR CONSEQUENTIAL, AND INCLUDING ATTORNEYS FEES AND LEGAL COSTS, THAT MAY
RESULT FROM THE INSTALLATION, OPERATION, USE OF, OR INABILITY TO USE WARRANTORS’ PRODUCTS AND
SERVICES, OR FROM THE FAILURE OF THE WARRANTORS’ SYSTEM TO REPORT A GIVEN EVENT OR CONDITION,
WHETHER OR NOT CAUSED BY WARRANTORS’ NEGLIGENCE.
YOU AGREE TO RELEASE, WAIVE, DISCHARGE AND COVENANT NOT TO SUE WARRANTORS, THEIR OWNERS,
DIRECTORS, OFFICERS, EMPLOYEES, AGENTS, SUPPLIERS OR AFFILIATED COMPANIES, FOR ANY AND ALL

5
LIABILITIES POTENTIALLY ARISING FROM ANY CLAIM, DEMAND OR ACTION BASED UPON ANY LOSSES,
LIABILITIES, DAMAGES OR COSTS, INCLUDING BUT NOT LIMITED TO DAMAGES THAT ARE DIRECT OR INDIRECT,
INCIDENTAL, SPECIAL OR CONSEQUENTIAL, AND INCLUDING ATTORNEYS FEES AND LEGAL COSTS, THAT MAY
RESULT FROM THE INSTALLATION, OPERATION, USE OF, OR INABILITY TO USE WARRANTORS’ PRODUCTS AND
SERVICES, OR FROM THE FAILURE OF THE WARRANTORS’ SYSTEM TO REPORT A GIVEN EVENT OR CONDITION,
WHETHER OR NOT CAUSED BY WARRANTORS’ NEGLIGENCE, EXCEPT AS NECESSARY TO ENFORCE THE EXPRESS
TERMS OF THIS LIMITED WARRANTY.
EXCLUSIVE WARRANTY: THE LIMITED WARRANTY OR WARRANTIES DESCRIBED HEREIN CONSTITUTE THE SOLE
WARRANTY OR WARRANTIES TO THE PURCHASER. ALL IMPLIED WARRANTIES ARE EXPRESSLY DISCLAIMED,
INCLUDING: THE WARRANTY OF MERCHANTIBILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR USE
AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND THE WARRANTY OF NON-INFRINGEMENT
AND/OR ANY WARRANTY ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
It must be clear that the Warrantors are not insuring your premises or business or guaranteeing that there will not be damage to
your person or property or business if you use this Product. You should maintain insurance coverage sufficient to provide com-
pensation for any loss, damage, or expense that may arise in connection with the use of products or services, even if caused by
Warrantors’ negligence. The warrantors assume no liability for installation of the Product and/or interruptions of the service due
to strikes, riots, floods, fire, and/or any cause beyond Seller’s control, further subject to the limitations expressed in any License
Agreement or other Agreement provided by Warrantors to purchaser.
The agreement between the Warrantors and the Purchaser, including but not limited to the terms and conditions herein shall not
be governed by the Convention for the International Sale of Goods. Where applicable, the Uniform Commercial Code as adopted
by the State of Delaware shall apply.
4. PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: In the event that the Product does not conform to this
warranty, the Product should be shipped or delivered freight prepaid to a Warrantor with evidence of original purchase.
5. LEGAL REMEDIES AND DISCLAIMER: Some jurisdictions may not allow, or may place limits upon, the exclusion and/or
limitation of implied warranties, incidental damages and/or consequential damages for some types of goods or products sold to
consumers and/or the use of indemnification terms. Thus, the exclusions, indemnification terms and limitations set out above
may not apply, or may be limited in their application, to you. If the implied warranties can not be excluded, and the applicable
law permits limiting the duration of implied warranties, then the implied warranties herein are to be limited to the same duration
as the applicable written warranty or warranties herein. The warranty or warranties herein may give you specific legal rights that
will depend upon the applicable law. You may also have other legal rights depending upon the law in your jurisdiction.
6. CHOICE OF FORUM AND CHOICE OF LAW: In the event that a dispute arises out of or in connection with this Limited
Warranty, then any claims or suits of any kind concerning such disputes shall only and exclusively be brought in either the Court
of Common Pleas of Delaware County, Pennsylvania or the United States District Court for the Eastern District of Pennsylvania.
Regardless of the place of contracting or performance, this Limited Warranty and all questions relating to its validity, interpre-
tation, performance and enforcement shall be governed by and construed in accordance with the laws of the State of Delaware,
without regard to the principles of conflicts of law.
Effective date 04/01/2009
PHONETICS, INC. d.b.a. SENSAPHONE
901 Tryens Road
Aston, PA 19014
Phone: [phone] Fax: [phone]
www.sensaphone.com

6
DRY CONTACT NODE
DESCRIPTION
The IMS-4000E Dry Contact Node provides eight dry contact inputs (normally open/normally closed) and works in conjunction
with the IMS Host. The device communicates with the IMS-4000E Host via its Ethernet connection. No Dry Contact Bridges are
required when using this device. The unit uses four AA rechargeable NiMH batteries (included) for power backup in the event
of a power failure. Both main power and battery charge are monitored and can be programmed to trip alarms as well. The unit
comes in a black plastic enclosure with tabs for wall mounting. Rubber feet are also included for placement on a shelf/desktop.
Package Contents:
(1) IMS-4010E Dry Contact Node w/Batteries installed
(1) 12VDC Power Supply
(1) CAT5 Ethernet Cable
(1) DB9 Null Serial Cable
(1) Sensaphone Screwdriver
(4) Plastic drywall anchors
(4) #6 Metal tapping screws
(4) Rubber feet
DEVICE LAYOUT
The Dry Contact Node is powered by a 9VDC power supply. The device communicates to an IMS-4000E Host using its Ethernet
port (10/100). The network settings must be configured using the serial port and a terminal emulation program (9600, 8, n,1).
All IMS devices must be configured with a static IP address. The unit also includes a power led and a power switch. See the fig-
ure below:
1. 12VDC power jack
2. RS232 Serial port
3. Ethernet port
4. Power led
5. Power switch
6. Input terminal strip
7. Dip Switches (bottom of enclosure)
SERIAL PORT
The RS-232 serial port is used to configure the network settings. The port is DB9 male DTE and operates at 9600 baud, 8 data
bits, no parity, and 1 stop bit. A DB9 female–female null modem cable is required to configure the network settings.
RJ-45 10/100BASE-T ETHERNET PORT
This jack is for connecting to your network so that the IMS-4010E Dry Contact Node can communicate with the IMS-4000E
Host. Two LEDs are provided to indicate Link Status (green) and Receive Data status (yellow).
POWER SWITCH
The power switch connects main power and battery power to the system. In the event that main power fails, the backup battery
will automatically power the device.
SENSOR INPUTS
The eight sensor inputs connect to your normally-open or normally-closed dry contacts. You may need to loosen the screw ter-
minals before inserting the wire. Be sure to strip at least 1/2” (1.27cm) of insulation from the wires before inserting them into
the terminal strip. Do not over-tighten the screw terminals.

7
DIP SWITCHES
The inputs must be configured as either normally open or normally closed using the dip switches located on the bottom of the
enclosure. The switches are numbered 1-8 corresponding to the 8 inputs. The OFF position is for Normally-Open (default) and
the ON position is for Normally-Closed. A pen or small screwdriver can be used to move the dip switches.
O N
1 2 3 4 5 6 7 8
Dip switches on bottom of enclosure
INSTALLATION
The device can be either wall mounted or rest on a shelf or tabletop. The enclosed screws and drywall anchors can be used for
wall mounting. Drill holes as shown below and insert the drywall anchors, then attach the enclosure with the screws.
3.5
6.75
NETWORK CONFIGURATION
The IMS-4010E Dry Contact Node has a serial port on the side which is used to configure network settings. A dumb terminal
or terminal emulation software is required to get online and set up the configuration. The port is male DTE, so a DB9 female–
female null modem cable will be required. Terminal communication settings must be set to:
• 9600 baud, no parity, 8 data bits, 1 stop bit, no flow control
To get online with the device, connect your terminal to the serial port and press <RETURN>. A menu will appear which will
guide you through the setup.
Sensaphone IMS-4000E Node Unit Version: 1.4.7
Main Menu
1. Display Network configuration
2. Configure Network settings
3. Reset to factory defaults
4. Reboot
5. Logout
Enter option->
To display the present Network Configuration settings, select Option 1. To program the Network settings, select Option 2. Note
that the Dry Contact Node must have network visibility of the Host for the IMS-4000E system to function properly. For Network
changes to take effect you must reboot the unit

8
(Option 4). A typical sample is shown below:
Network Configuration
Physical Address 00:07:F9:00:10:18
Parent Host IP address 10.1.2.47 (Connected)
Node IP Address 10.1.4.17
Subnet Mask 255.255.255.0
Default Gateway 10.1.4.1
DNS Server 10.1.2.111
Node name 48th Floor Chicago
Ethernet Mode Auto
Allow remote configuration Y
Press any key to return to main menu
NOTE: You can remotely reconfigure the Node network settings using the IMS-4000E ConsoleView software if the Allow
Remote Configuration option is set to Y. However, the Node must initially be configured via the serial port before any remote
configuration is possible.
Option 3 will reset the Node to factory default settings. All programming and network settings will be deleted.
Option 4 will reboot the system. You must reboot for new Network settings to take effect.
Option 5 will logout without rebooting.
NETWORK CONFIGURATION DEFINITIONS
Parent Host IP Address: This is the IP address of the IMS-4000E Host that this Node is associated with.
Node IP Address: This is the IP address assigned to the IMS-4000E on your network. This address is provided by you or your
network administrator. It is formatted as a standard dotted decimal number.
Subnet Mask: This is the subnet mask which distinguishes the portion of the IP address that is the network ID from the portion
that is the station ID.
Default Gateway: A TCP/IP network must have a gateway to communicate beyond the LAN identified by the network ID. A
gateway is a computer or router that is connected to two different networks and can move TCP/IP data from one to the other. If
your TCP/IP network has more than one LAN, or if you are connecting to the Internet, you will need to know the
IP address of the gateway that will transfer TCP/IP data in and out of your LAN. A single LAN that is not connected to other
LANs does not require a gateway setting.
DNS Server: The DNS server is used to translate site names into actual numeric network addresses. Enter the IP address of the
DNS server for your network.
Node Name: This name will appear in the IMS-4000E ConsoleView Software. In systems with many Nodes, the Name is useful
for identifying one node from another.
Ethernet Mode: The unit defaults to Compatibility Mode, which means it will try connecting to the network using 100Mbps half
duplex, and if it is unsuccessful it will then try 10Mbps half-duplex. Other settings are available to force the device to either 10
or 100Mbps. An Auto setting is also available which will attempt a full duplex connection, however, this may not be compatible
with certain network hubs/switches.
PROGRAMMING
The IMS-4010E Dry Contact Node will appear in the IMS-4000E ConsoleView Software as a Node device below the Host. Refer
to the IMS-4000E User’s Manual for sensor programming instructions.

9
BATTERY BACKUP
The Dry Contact Node is designed to use rechargeable batteries only. The device includes (4) AA nickel metal hydride (NiMH)
2600mAhr rechargeable batteries. The batteries will keep the device operating for approximately seven hours in the event of a
power failure. The unit will maintain proper charging of the batteries while power is on. Do not install alkaline batteries - they
will damage the device and leak. The batteries should be replaced every 4-5 years.
To replace the batteries, turn off the power switch and remove the cover. Remove the old batteries from the battery holder with a
small screwdriver. Install the new NiMH rechargeable batteries following the polarity markings in the battery holder. Re-attach
the top cover and turn on the power switch. Allow up to 48 hours to charge a new set of batteries.
SPECIFICATIONS
Number of Inputs 8
Input Type AC Power, Backup Battery
Ethernet 10/100 Base-T, 10/100Mbps
Serial Port 9600Bps (N, 8, 1) for network configuration
Local Indicators Power LED, Ethernet LEDs
Operating Temperature 32° to 122° F (0° to 50° C)
Operating Humidity 5 to 90 % RH non-condensing
Power Consumption 2.5W
Power Requirements
IMS-4010E 120VAC 60Hz/9-12VDC 300mA (min) Power Supply
IMS-4010E-INT 90-260VAC 50/60Hz 9-12VDC 300mA (min) Multi-plug Power Supply
Battery Backup Four AA NiMH Rechargeable Batteries, 2000mAHr or higher (included)
Dimensions 7.3” x 5.5” x 1.5” (18.5 x 13.9 x 3.8 cm)
Weight 2lbs (.9kg)
RETURNING AN IMS UNIT FOR REPAIR
In the event that any of your Sensaphone IMS-4000E units do not function properly, we suggest that you do the following:
1) Record your observations regarding the individual unit’s malfunction.
2) Call the Technical Service Department at 610.558.2700 prior to sending the unit to Sensaphone for repair.
If the unit must be sent to Sensaphone for Servicing, please do the following:
1) Unplug the power supply.
2) Disconnect all cables, inputs and wiring.
3) Carefully pack the unit to avoid damage in transit. Use the original container (if available) or a sturdy shipping box.
4) To avoid shipping delays, you must include the following information :
a) Your name, address and telephone number.
b) A note explaining the problem.
5) Ship your package to the address below:
SERVICE DEPARTMENT
SENSAPHONE®
901 Tryens Road
Aston, PA 19014
6) Ship prepaid and insured via UPS or US Mail to ensure a traceable shipment with recourse for damage or replacement.