Sensio SE9080HD User manual

1 x Fitting Instructions
HD LED
In-CabInEt
LIgHt wItH
IR SEnSoR
CODE: SE9080HD
Components
Important safety information
Tools required
INSTALLATION
INSTRUCTIONS
IMPORTANT: please read these instructions before commencing installation and retain for future reference.
1 x SE9080HD HD LED In-Cabinet Light
with mounting bracket and cable
Please read these instructions carefully before attempting to install
this product. It is advisable to keep these instructions in a safe place
for further reference.
We recommend that you consult a qualified electrician.
All electrical installations must be carried out in accordance
with current IEE wiring regulations (BS7671).
These products must not be modified, if any modifications are
made, it may invalidate the warranty and may render the product
unsafe. These LED lights operate low voltage (24V).
Do not wire the individual LED light fittings directly to the mains.
This product is for indoor use only. Keep out of moisture and use
only in dry rooms.
• If in doubt installation must be carried out by a qualified
electrician.
• Install on smooth flat surface(s) only.
• The Wattage of this product is 2W. Make sure that
the LED driver used with these fittings has an adequate
max wattage.
• We recommend using a SE40553 15W LED Driver with this fitting.
You will be able to run a maximum of 3 fittings per driver.
•for more fittings, use the SE40555 15W 24V LED Driver. You will
be able to run a maximum of 6 fittings per driver.
Safety instructions
1. Before commencing installation or maintenance, isolate the main
electrical supply for the appropriate circuit at the fuse board.
2.
This product requires a 24V LED driver which is only
suitable for connecting to a 240V 50Hz supply.
3. The light should be mounted onto a secure surface.
4. Position lights where they will not be exposed to steam
or splashes etc.
5. Suitable for furniture lighting.
6. When the lamp expires the fitting must be replaced.
7. Class III safety extra low voltage (SELV).
Waste Electrical & Electronic Equipment (WEEE)
The Symbol on the product, or on the document accompanying the product, the crossed out
wheelie bin symbol, indicated that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic waste.
Power DrillPZ1 Screw Bit10mm
Drill Bit
Pencil

Installation
Operation
Maintenance & Care
Once fixed the SE9080HD light
is activated on the opening
of the cabinet door. The IR
sensor detects that the door
is no longer in its path and
activates the light.
HD LED In-CabInEt LIgHt
wItH IR SEnSoR
• Ensure that the power is disconnected prior to cleaning.
• To keep the finish of this product, wipe over with soft cloth periodically.
• Do not use harsh chemical solvents, it may dis-colour or damage the finish.
7
Finally wire the LED driver to 240V mains supply
or 13A plug top.
5
Re-attach the light unit to the bracket once
fixed.
Taking the bracket, mark-up
the positions for the screw
holes in the cabinet.
3
Secure the bracket with
2 screws tightly to the inside
of the cabinet.
4
Unclip the bracket from the back of the
light fitting.
2
Unit 7 Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY
www.sensio.co.uk
Technical drawings for illustration purposes only, Sensio has the right to change any information
without prior notice. Make sure you check all hole cut outs before work commences.
2
6
Plug the white connector into the 24V LED
driver distributor block. Beware not to exceed
the wattage of the LED driver, the max wattage
will be displayed on the 24V LED driver and on
the light unit fitting it will display the wattage
requirement.
Drill hole in bottom of cabinet and feed
cable through.
1