Sensio SIGMA S-BEND FLEXIBLE STRIP User manual

IMPORTANT: please read these instructions before commencing installation and retain for future reference.
INSTALLATION
INSTRUCTIONS
SIGMA SBEND
FLEXIBLE STRIP
CODE: SE10255C0/W0
Safety instructions
1. Before commencing installation or maintenance, please clear
the surrounding area of any trip hazards or sharp objects.
2. This product is only suitable for connecting to a 24V DC supply.
3. The light should be mounted onto a secure, clean surface
using the instructions provided.
4. Never exceed the total output of the LED Driver.
5. Suitable for furniture lighting.
6. If an LED expires the tting must be replaced.
Waste Electrical & Electronic Equipment (WEEE)
The symbol on the product, or on the document accompanying the product, the crossed out wheelie bin
symbol, indicates that this product may not be treated as household waste. Instead it shall be handed over to
the applicable collection point for the recycling of electrical and electronic waste.
Please read these instructions carefully before attempting to
install this product. It is advisable to keep these instructions in a
safe place for further reference.
We recommend that you consult a qualied electrician. All
electrical installations must be carried out in accordance with
current IEE wiring regulations (BS7671).
These products must not be modied, if any modications are
made it may invalidate the warranty and may render the product
unsafe. These LED lights operate low voltage (24V).
Do not wire the individual LED light ttings directly to the mains.
This tting is for indoor use only (IP20 rated).
• If in doubt installation must be carried out by a
qualied electrician
• Install on smooth at surface(s) only
• The strip can be cut and reconnected every 100mm
• The wattage is 18W per 5m reel
• In order to run this product you will need a 2.5m driver
connection cable (SE101080)
• Class III safety extra low voltage (SELV)
Components Tools Required
Important safety information
Scissors 6mm Drill Bit Power DrillFitting Instructions1x Sigma Flexible Strip

SIGMA SBEND FLEXIBLE STRIP
Maintenance & Care
• As the LEDs are exposed on this tting you should not wipe the item or expose it to liquids / cleaning agents.
Sensio, Unit 7, Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY
www.sensio.co.uk
80 °
Installation
1 2
Measure the length of each area to which the strip is
to be installed.
If the strip is to be cut to length ensure you only cut
along the indicated cut line. These points are every
100mm along the strip so cut at the closest possible
point.
Connect the driver connection cable (SE101080) to
the end of the strip by carefully inserting the strip
and rmly closing the cap. Ensure the + and – points
on the strip and cable match.
3
If you are running the strip around a corner please
ensure that you adhere to the following;
• The angle between the surface and the strip being
pulled should not exceed 20 degrees.
• Minimum bending diameter is 6cm (2.36in).
4
Ensure the surface the strip is being applied to is
clean. Remove the paper protecting the adhesive
on the back of the strip, position the strip carefully
ensuring it is straight and rmly press into place.
Plug the connector on the end of the cable into the
24V LED driver distribution block. Ensure the wattage
of the LED driver is not exceeded. Finally, connect the
driver to the mains supply.
5 6
Accessories
SE101080
2.5M Driver Connection Cable
*This item is required to run the
Sigma exible strip
SE100750
1.5M Inter-connecting Cable
If more than a single length of Sigma is to be powered, this can be achieved either by connecting the strips
together using either the inter-connecting clip, corner connector or inter-connecting lead (whichever is most
suitable), or by using a driver connection cable on each strip running these back to the driver.
SE100050
End Cap / Inter-connecting clip
Technical drawings are for illustrative purposes only. Sensio has the right to change any information without prior notice.
Make sure you check all hole cut outs before work commences.
Corner Application