Sensio Link-S SE79095 User manual

Sensio House, Unit 7, Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY
www.sensio.co.uk
Technical drawings for illustraon purposes only, Sensio has the right to change any informaon without
prior noce.
Waste Electrical & Electronic Equipment (WEEE)
The symbol on the product, or on the document accompanying the product, the crossed out wheelie
bin symbol, indicates that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collecon point for the recycling of electrical and
electronic waste.
3. Never exceed the total output of a LED driver or receiver.
4. Suitable for furniture lighng.
5. Class III safety extra low voltage (SELV).
1. This product is only suitable for connecng to Sensio LED lights and
ngs.
2. Always read the installaon guide of any product used in conjuncon
with this product.
Safety Instruc�ons
Please read these instrucons carefully before aempng to install this
product. It is advisable to keep these instrucons in a safe place for future
reference.
We recommend that you consult a qualied electrician. All electrical
installaon must be carried out in accordance with current IEE wiring
regulaons (BS7671).
These p
These products must not be modied, if any modicaon are made, it may
invalidate the warranty and may render the product unsafe. These LED
lights operate low voltage (24V).
• Install on smooth at surface(s) only.
• Do not exeed or stretch the cable length of each wire.
• This product is IP20 Rated.
Important Safety Informa�on
Technical Specifica�on
Screwdriver
1 x Instrucons
Manual
2 x Screws
(SE79095 &
SE79195 Only)
Magnet & Reed Switch
( SE79095 & SE79295 Only)
Receiver
(SE79095 & SE79195 Only)
Tools Required
Components
IMPORTANT: Please read these instruc�ons before commencing installa�on and retain for future reference.
INSTALLATION
INSTRUCTIONS
Product Codes:
SE79095 - Link-S - Receiver, Magnet and Reed Switch
SE79195 - Link-S - Receiver
SE79295 - Link-S - Magnet & Reed Switch
Link-S - Receiver, Magnet
and Reed Switch
Lighng Control
Sensio V3
UK Address: Sensio Ltd, Unit 7, Speedwell Road, Castleford, West Yorks, WF10 5PY
EU Rep.: Sensio Lighting Dublin Ltd, The Black Church, St. Mary's Place, Dublin, Ireland, D07 P4AX
Sensio - V4

Technical drawings for illustraon purposes only, Sensio has the right to change any informaon
without prior noce.
Sensio V3
www.sensio.co.uk
Sensio House, Unit 7, Speedwell Road, Whitwood, Castleford, West Yorkshire, WF10 5PY
• Ensure that the power is disconnected prior to cleaning.
• To keep the nish of this product, wipe over with socloth periodically.
• Do not use harsh chemical solvents, this may dis-colour or damage the nish.
• Do not over-ghten screws on the terminal block.
Maintenance & Care
Connect your light to the receiver by inserng
the male-ended JB4 cable into the female-end.
Receiver - Underside View
Synchronizaon BuonSignal LED
To clear the memory of the
receiver, press the
synchronizaon buon with
a sharp object for ve
seconds. The signal LED will
icker once.
2
Move the magnet apart
from the reed switch
and then touch them
again. The signal LED
will icker once when
pairing is complete.
Press the synchronizaon
buon on the underside of
the receiver with a sharp
object. The signal LED will
icker once.
1
Each receiver can connect with up to ve
magn
magnets and reed switches. The recommended
scenario for this setup would be to have a
magnet and reed switch on a series of cabinet
doors. Opening each cabinet door would then
trigger all the lights connected to the receiver.
For example, a series of in-cabinet lights.
E
Each magnet and reed switch can be connect
with up to ve dierent receivers. The
recommended scenario for this setup would be
to install the magnet and reed switch on the
door to a room. Opening the door will then
trigger all the lights connected to the receivers.
For example, all of the lighng in that room.
Opera�on
Driver
Receiver
4
Secure the receiver in posion using the screws
included. Finally, connect the driver to the
mains supply.
Receiver
5
Connect the male-ended cable from the
receiver into the LED Driver.
Driver
Receiver
3
Peel the adhesive backing tape oof the
magnet and sck it into a posion where it will
make contact with the Reid switch when the
doors are closed. Note: The magnet can make
contact with the side of the Reid switch.
Reid
Switch Magnet
Magnet
2
Peel the adhesive backing tape oof the Reid
switch and sck it in your desired locaon.
Note: The product is suitable for installaon in
many scenarios, please ensure that you
measure and plan before installaon.
1
Reid Switch
Installa�on
Link-S - Receiver, Magnet and Reed Switch
If you are installing a Sensio Wireless Magnec
Contact and Receiver with mulple Reid switch-
es and magnets, simply follow stages 1 and 2
for installaon. Once installed, each switch will
trigger the lighng when the two components
break contact.
UK Address: Sensio Ltd, Unit 7, Speedwell Road, Castleford, West Yorks, WF10 5PY
EU Rep.: Sensio Lighting Dublin Ltd, The Black Church, St. Mary's Place, Dublin, Ireland, D07 P4AX
Sensio - V4