Sentera Controls FIMX8 Service manual

FIMX8 AIR FILTER MONITOR
Mounting and operating instructions

www.sentera.eu
MIW-FIMX8-EN-000 - 06 / 09 / 2023 2 - 90
FIMX8 AIR FILTER MONITOR
Table of contents
SAFETY AND PRECAUTIONS 3
PRODUCT DESCRIPTION 4
ARTICLE CODES 4
INTENDED AREA OF USE 4
TECHNICAL DATA 4
STANDARDS 4
OPERATIONAL DIAGRAM 5
MOUNTING INSTRUCTIONS IN STEPS 5
VERIFICATION OF INSTALLATION 7
OPERATING INSTRUCTIONS 8
TRANSPORT AND STORAGE 9
WARRANTY AND RESTRICTIONS 9
MAINTENANCE 9

www.sentera.eu
MIW-FIMX8-EN-000 - 06 / 09 / 2023 3 - 90
back to the table of contents
FIMX8 AIR FILTER MONITOR
SAFETY AND PRECAUTIONS
Read all the information, the datasheet, Modbus map, mounting and operating
instructions and study the wiring and connection diagram before working with the
product. For personal and equipment safety, and for optimum product performance,
make sure you entirely understand the content before installing, using or maintaining
this product.
For safety and licensing (CE) reasons, unauthorised conversion and/ or modifications
of the product are inadmissible.
e product should not be exposed to abnormal conditions, such as extreme
temperatures, direct sunlight or vibrations. Long-term exposure to chemical
vapours in high concentration can affect the product performance. Make sure the
work environment is as dry as possible; avoid condensation.
All installations shall comply with local health and safety regulations and local
electrical standards and approved codes. is product can only be installed by
an engineer or a technician who has expert knowledge of the product and safety
precautions.
Avoid contact with energised electrical parts. Always disconnect the power supply
before connecting, servicing or repairing the product.
Always verify that you apply appropriate power supply to the product and use
appropriate wire size and characteristics. Make sure that all the screws and nuts
are well tightened and fuses (if any) are fitted well.
Recycling of equipment and packaging should be taken into consideration and these
should be disposed of in accordance with local and national legislation/regulations.
In case there are any questions that are not answered, please contact your
technical support or consult a professional.

www.sentera.eu
MIW-FIMX8-EN-000 - 06 / 09 / 2023 4 - 90
back to the table of contents
FIMX8 AIR FILTER MONITOR
PRODUCT DESCRIPTION
FIMX8 are filter monitors for observation of air filters in HVAC systems. eir purpose
is to provide information on filter status and notify on the level of clogging. ey can
be equipped with one or two differential pressure sensors to measure the pressure
drop on both sides of the filter. e pressure difference shows how clogged the filter
is. e internet connection is based on the integrated Sentera Internet Gateway
(SIG-M-2 or SIGWM). Via SenteraWeb measurements can be monitored and Modbus
registers can be reset.
ARTICLE CODES
Article code Monitoring of Wi-Fi Ethernet LAN
connection
FIM18-1K0-WF 1 filter
yes
no
FIM28-1K0-WF 2 filters no
FIM18-1K0-EW 1 filter yes
FIM28-1K0-EW 2 filters yes
INTENDED AREA OF USE
■Online monitoring of air filters in HVAC systems using SenteraWeb
TECHNICAL DATA
■Power supply: 85—264 VAC / 50—60 Hz
■Maximum current consumption: 25 mA
■1 or 2 differential pressure channels with built-in digital high resolution differential
pressure sensor
■Data transmission to and from the Internet via standard Ethernet or Wi-Fi
■Firmware updates via internet (SenteraWeb) or Wi-Fi
■LED indications
■Implemented MQTT protocol
■Configurable filter warning and filter alarm pressure
■Clogged filter notifications are sent by SenteraWeb via SMS or email
■Operating ambient conditions:
►Temperature: -5—65 °C
►Rel. humidity: < 95 % rH (non-condensing)
■Storage temperature: -20—70 °C
STANDARDS
■EMC Directive 2014/ 30/EC:
►EN 61000-6-2:2005 Electromagnetic compatibility (EMC) - Part 6-2: Generic standards
- Immunity for industrial environments Amendment AC:2005 to EN 61000-6-2
►EN 61000-6-3:2007 Electromagnetic compatibility (EMC) - Part 6-3: Generic
standards - Emission standard for residential, commercial and light-industrial
environments Amendments A1:2011 and AC:2012 to EN 61000-6-3
►EN 61326-1:2013 Electrical equipment for measurement, control and laboratory
use - EMC requirements - Part 1: General requirements
►EN 55011:2009 Industrial, scientific and medical equipment - Radio-frequency
disturbance characteristics - Limits and methods of measurement Amendment
A1:2010 to EN 55011
►EN 55024:2010 Information technology equipment - Immunity characteristics -
Limits and methods of measurement

www.sentera.eu
MIW-FIMX8-EN-000 - 06 / 09 / 2023 5 - 90
back to the table of contents
FIMX8 AIR FILTER MONITOR
■LVD directive 2014/35/EU:
►EN 60529:1991 Degrees of protection provided by enclosures (IP Code)
Amendment AC:1993 to EN 60529
►EN 62311:2008 Assessment of electronic and electrical equipment related to
human exposure restrictions for electromagnetic fields (0 Hz - 300 GHz)
►EN 60950-1:2006 Information technology equipment - Safety - Part 1: General
requirements Amendments AC:2011, A11:2009, A12:2011, A1:2010 and A2:2013
to EN 60950-1
■Radio equipment directive 2014/53/EU
►EN 300 328 V2.1.1 Wideband transmission systems; Data transmission
equipment operating in the 2,4 GHz ISM band and using wide band modulation
techniques; Harmonised Standard covering the essential requirements of article
3.2 of Directive 2014/53/EU
■ETSI EN 301 489-1 V2.1.1 (2017-02) Electromagnetic Compatibility (EMC) standard
for radio equipment and services; Part 1: Common technical requirements;
Harmonised Standard covering the essential requirements of article 3.1(b) of
Directive 2014/53/EU and the essential requirements of article 6 of Directive
2014/ 30/EU
■ETSI EN 301 489-17 V3.1.1 (2017-02) Electromagnetic Compatibility (EMC)
standard for radio equipment and services; Part 17: Specific conditions for
Broadband Data Transmission Systems; Harmonised Standard covering the
essential requirements of article 3.1(b) of Directive 2014/53/EU
■RoHs Directive 2011/65/EC
►EN IEC 63000:2018 Technical documentation for the assessment of electrical
and electronic products with respect to the restriction of hazardous substances
OPERATIONAL DIAGRAM
Filter warning level
IR2 (IR6*)
Input
register
values
1
1
0
Dierential
pressure
* For product versions FIM28-1K0-WF and FIM28-1K0-EW
Filter alarm level
IR3 (IR7*)
MOUNTING INSTRUCTIONS IN STEPS
Before you start mounting the unit, read carefully “Safety and Precautions”.
Choose a smooth surface for installation (awall, panel, etc.) and follow these steps:
1. Unscrew the front cover of the enclosure to remove it.
2. Attach the enclosure to the surface with suitable fasteners, taking into account
the mounting dimensions in Fig. 1 and the correct mounting position shown in
Fig. 2 below.

www.sentera.eu
MIW-FIMX8-EN-000 - 06 / 09 / 2023 6 - 90
back to the table of contents
FIMX8 AIR FILTER MONITOR
Fig. 1 Mounting dimensions Fig. 2 Mounting position
64 mm
139,7 mm
83,8 mm
97,7 mm
F2
F2 +
F1
F1 +
Correct Incorrect
F2
F2 +
F1
F1 +
F2
F2 + F1 F1 +
F2
F2 +
F1
F1 +
3. Put back the front cover and secure it with the screws.
4. Connect the nozzles to the duct (see Fig. 3). Depending on the application, you
must use a specific connection set such as Sentera’s PSET-PVC-200 or PSET-
QF-200 as indicated in Fig. 3 below.
Fig. 3 Connecting with accessories
Application: Measuring differential pressure [Pa] or volume flow [m³/h]
using PSET-PVC
SenteraWeb
5. Insert the power cord in the power socket.
6. Activate the power supply.

www.sentera.eu
MIW-FIMX8-EN-000 - 06 / 09 / 2023 7 - 90
back to the table of contents
FIMX8 AIR FILTER MONITOR
7. Connect the internet gateway to the internet via Wi-fi or via a LAN cable. If you
want to connect the FIMX8 to your internet router via cable, you can do so via
the Ethernet connection, using a standard network cable - Fig. 4.
Fig. 4 Connections
NOTE For sensor calibration and Modbus registers reset procedures, see section
“Operating instructions”.
Optional settings
To assure correct communication, the NBT needs to be activated in only two devices
on the Modbus RTU network. If necessary, enable the NBT resistor via 3SModbus or
Sensistant (Holding register 9).
Example 1 Example 2
RX
ТX
NBT
NBT
Slave 2
Master
Slave n
Slave 1
Slave 2
Slave 1
RX
ТX
NBT
NBT
Master
Slave n
NOTE On a Modbus RTU network, two bus terminators (NBTs) need to be activated.
For the complete Modbus register data, refer to the product Modbus Register
Map, which is a separate document attached to the article code on the website
and contains the registers list. Products with earlier firmware versions may not be
compatible with this list.
NOTE
VERIFICATION OF INSTALLATION
After supplying the unit and when the unit is measuring the filter status, the LED(s)
on the enclosure should blink three times, even if the LED brightness is set to ‘0’ via
holding register 31.

www.sentera.eu
MIW-FIMX8-EN-000 - 06 / 09 / 2023 8 - 90
back to the table of contents
FIMX8 AIR FILTER MONITOR
e green LED1 inside the enclosure lights up to indicate successful connection to the
internet. If connecting to the internet is unsuccessful, the red LED3 on the printed
circuit board lights up. e SIG-M-2 or SIGWM gateway is integrated in the unit, so if
you need further information, consult the SIG-M-2 or SIGWM documentation on our
website. For further details on LED indications, please see Fig. 5 and Fig. 6 below.
NOTE For more information, refer to the product datasheet - Settings and indications.
Fig. 5 LED indication connection to the Internet
Fig. 6 LED indications on cover
FIM18-1K0-X X FIM28-1K0-XX
Green Pressure level is lower than specified filter warning level.
Yellow Pressure level is higher than specified filter warning level but lower
than filter alarm level.
Red Pressure level is higher than filter alarm level.
Pink No communication with pressure sensor.
Bootloader mode: LED F1 is alternately blinking blue and green. It blinks red
during programming.
ATTENTION e status of the LEDs can be checked only when the unit is energised. Take the
relevant safety measures!
ATTENTION LED intensity can be adjusted between 0 and 100 % with a step of 10 % according
to the value set in Holding register 31.
OPERATING INSTRUCTIONS
Calibration procedure:
1. Disconnect the nozzles and make sure they are not clogged.
2. Write “1” in holding register 20 to calibrate sensor 1. If your product version has
two sensors, to calibrate the second one write ‘1’ in Holding register 30.

www.sentera.eu
MIW-FIMX8-EN-000 - 06 / 09 / 2023 9 - 90
back to the table of contents
FIMX8 AIR FILTER MONITOR
ATTENTION Make sure the nozzles are disconnected and free.
Internet connection reset button
Both the EW and WF product versions feature Wi-Fi connection. e EW version also
features LAN connection. By pressing the button in Fig. 7 below you will reset the
Ethernet LAN module in product versions FIM18-1K0-EW and FIM28-1K0-EW. e
same button in the FIM18-1K0-WF and FIM28-1K0-WF product versions will reset
the Wi-Fi module.
Fig. 7 Internet connection reset button
Reset tact switch for Wi-Fi (for both EW and WF versions)
In case of connection problems or to stop Wi-Fi connection: press reset tact switch
shown in Fig. 8 below and hold it until the blue LED on the Wi-Fi module lights up.
When the LED goes out, Wi-Fi connection is broken. If necessary, you can reconnect
to any network via the SenteraWeb configuration page: http://192.168.1.123.
Fig. 8 Reset tact switch for Wi-Fi
TRANSPORT AND STORAGE
Avoid shocks and extreme conditions; stock in original packing.
WARRANTY AND RESTRICTIONS
Two years from the delivery date against defects in manufacturing. Any modifications
or alterations to the product after the date of publication relieve the manufacturer
of any responsibilities. e manufacturer bears no responsibility for any misprints or
mistakes in this data.
MAINTENANCE
In normal conditions this product is maintenance-free. If soiled, clean with a dry or
damp cloth. In case of heavy pollution, clean with a non-aggressive product. In these
circumstances the unit should be disconnected from the supply. Pay attention that
no fluids enter the unit. Only reconnect it to the supply when it is completelydry.