Seorim Technology SVC-3020 / 41NR (DN) Installation instructions

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
1
MPEG4/JPEG Network Camera
MODEL: SVC-3020 / 41NR (DN), SVC-3020 / 41PR (DN)
Full Manual (English)
Version 1.0

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
2
Warning
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage" within the product's enclosure that may
be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
3
Warning
This equipment has been tested and found to comply with the limits for a Class B Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment can radiate radio frequency
energy therefore, if it is not installed and used in accordance with the instruction, it may cause
harmful interference to radio communication. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment causes harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution
Any changes or modifications in construction of this device which are not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
4
Precautions
1. HEED WARNINGS
Adhere to all warnings on the appliance and in the operating instructions.
2. POWER SOURCES
Operate this equipment only from the type of power source indicated on the label. If you are not
sure of the type of power being used, consult your dealer or local power company.
3. OVERLOADING
Do not overload wall units and extension cords, as this can result in a risk of fire or electric shock.
Frayed power cords, damaged or cracked wire insulation, and broken plugs are dangerous.
Periodically examine the cord and replace it if appearance indicates damage or deteriorated
insulation.
4. POWER PLUG PROTECTION
Route the power supply cords so they cannot be walked on or pinched by items placed upon or
against them.
5. VENTILATION
Do not block the slots or openings of the video server and do not place the equipment on a bed,
soft rug, or other similar surface.
6. ATTACHMENTS
Do not use attachments other than those specifically recommended by the equipment
manufacturer as they may cause hazards.
7. TO PREVENT SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE
If you spill liquid on the unit, consult authorized service personnel. Moisture can damage internal
parts. Do not use this equipment near sources of water.
8. ACCESSORIES
Use only with a manufacturer recommended card, stand, tripod, bracket or table. The equipment
may fall, causing serious injury to a child or adult and serious damage to the appliance.
9. CLEANING THE OUTSIDE SURFACES
Unplug this equipment from the wall outlet before cleaning. Use a damp cloth for cleaning.
10. REQUIRING SERVICE
Unplug the equipment from the wall outlet and request qualified service personnel.
11. SAFETY CHECK
Upon completion of any service or repairs to this equipment, ask the service technician to perform
safety checks to determine that the equipment is in safe operating condition.

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
5
12. IMPORTANT NOTE TO THE INSTALLER
This installation should be made by a qualified service person and should conform to all local
codes. In order to provide this product with protection against risk of unintentional operation by
employees, customers, janitors and cleaners working on the premises, and from falling objects,
building vibrations and similar causes, it is recommended this product be enclosed in the tamper-
resistant lock box. Make sure that the lock box is well ventilated or maintained with an air cooling
system.

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
6
Table of Contents
1. Introduction of SVC-3020................................................................................... 8
1.1. Product Overview........................................................................................ 8
1.2. Basic Function............................................................................................. 8
1.3. Features .................................................................................................... 10
1.4. Packing Contents .......................................................................................11
1.5. System Requirements............................................................................... 12
1.6. System Configuration................................................................................ 13
1.7. Physical Description and Function............................................................. 14
1.7.1. Front View ........................................................................................ 14
1.7.2. Bottom View ..................................................................................................... 14
1.7.3. Rear View ......................................................................................................... 14
2. Basic Setup of SVC-3020................................................................................. 17
2.1. How to Use Lens ...................................................................................................... 15
2.1.1. Using Auto iris Lens ..................................................................................... 20
2.1.2. Using C-Mount Lens .................................................................................... 20
2.1.3. Using CS-Mount Lens ................................................................................. 20
2.2. Installation................................................................................................. 20
2.3. Network Setting of a PC............................................................................ 21
2.3.1. Verifying the network setup status of a user PC............................... 21
2.3.2. Operation of the Web Viewer (URL 192.168.1.10) ........................... 25
3. Configuration of Network Environment.......................................................... 29
3.1. Check-up Network Environment and Installation Type .............................. 29
3.2. Installation without a Router...................................................................... 30
3.2.1. Basic Setup ...................................................................................... 30
3.2.2. DNS Setup ....................................................................................... 33
3.2.3. Ports Setup....................................................................................... 34
3.3. Installation with a Router........................................................................... 35
3.3.1. Network Setup with a Router............................................................ 35
3.3.2 Check the configuration of a ROUTER, SVC-3020 and PC .............. 36
4. Display Mode.................................................................................................... 37
4.1. Initial Log-in Screen................................................................................... 37
4.1.1. Installation of the Web Viewer.......................................................... 37
4.1.2. Initial Log-in Screen of SVC-3020 .................................................... 38
4.2. Live Page .................................................................................................. 38

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
7
4.2.1. Screen Mode.................................................................................... 39
5. Admin Setting Mode......................................................................................... 41
5.1. General Setting ......................................................................................... 41
5.2. Encoder Setting......................................................................................... 42
5.3. Event Setting............................................................................................. 44
5.4. Network Setting......................................................................................... 48
5.5. Service Setting .......................................................................................... 49
5.5. Service Setting .......................................................................................... 50
5.6. Interface Setting ........................................................................................ 51
5.7. Motion Detect Setting................................................................................ 54
5.8. User Setting............................................................................................... 55
APPENDIX A. Connection Diagrams .................................................................. 56
APPENDIX B.Technical Specification of SVC-3020........................................... 58
APPENDIX C. Troubleshooting ........................................................................... 60

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
8
1. Introduction of SVC-3020
1.1. Product Overview
• About SVC-3020
The Intelligent Network Camera SVC-3020 provides advanced solutions for viewing, recording and
retrieving video over computer networks, including the Internet. The SVC-3020 compresses Video,
and then transmits the compressed video over computer networks at speeds up to 30 fps (25fps in
PAL). Additionally, SVC-3020 provides audio and alarm information from the remote site.
SVC-3020 has one audio input and one alarm input. The user can listen to the remote site with the
audio input. The SVC-3020 features are accessible through the Camera browser, allowing users to
access and control their systems anytime from virtually anywhere.
1.2. Basic Function
• Real time MPEG-4 compression
When the analog video is input, the video is compressed in the MPEG-4 format. The MPEG-4 is an
optimal compressing engine that compresses video files to reduce the size of memory. More video
files could be saved when saving from remote areas.
• Dual Codec (MPEG4 / JPEG) Support
SVC-3020 can encode analog video in either MPEG4 or JPEG. When you wish to get more vivid
image regardless of network bandwidth, JPEG format is recommended. SVC-3020 support both still
image and video in JPEG
• Stable system operation
Along with the Linux operating system, which is optimal for the embedded system, the hardware
watch-dog is used to enhance the system’s safety. The increase in the safety of the system makes
network service stable.
• User Access Control
The SVC-3020 server performs an access control check to verify whether the user is authorized.
If the user is not registered, the access to the 4 channel video server is blocked. Only the user with
the administrator right can set the default values and carry out the PTZ motions of the video server.
Users without the administrator right (observer) can only monitor.

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
9
• IP Filtering
SVC-3020 can block the access from a particular IP address through IP filtering. Only the IP
addresses recognized by the user can access the video server.
• Embedded Motion Detection function
SVC-3020 has an embedded sensor system that detects movements. The user can setup the
motion detection mode on the viewer. The observing areas of motion and sensitivity can be
regulated according to the user’s need. The user can also install various types of sensors
additionally (ex. Heat/shock/alarm sensor etc.), being connected with the video server.
• E-mail and FTP transmission
SVC-3020 sends images to the designated E-mail address or FTP Server when an alarm is raised or
movements are detected. Even when the user is not in the course of monitoring, the system notifies
the situation to the user automatically.
• Easy Firmware Update through Network
SVC-3020 users can easily enhance the functions of the system through network Firmware-Update
without having to pay additional expenses.
• Multi Viewer (16 Channel viewer) Software
In order to maximize the performance of the SVC-3020 video server, a Multi Viewer software is
provided free of charge with other accessories. The software should be installed in a user PC. It is
capable of connecting at most 16 analog cameras and has a set of convenient features such as
presetting, emergency recording and so forth. For example, recording starts automatically according
to the preset time and in case of emergency, it starts with a single click. Also, when playing, you can
fast-forward and fast-reverse at a high speed, which is 32 times faster than the normal playing speed.

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
10
1.3. Features
Network Board
NTSC : D1 (704 X 480) at 30 fps / PAL : D1 (704 X 576) at 25 fps
Monitor live video transmitted in real-time
- Remote monitoring up to 120 fps live video
- MPEG4/JPEG
- Low network bandwidth requirement
Simultaneous video and audio signal transmission
- Bi-directional Audio
- Monitoring voices and background sounds over a single connection
Built-in Web Server and Network Interface
Power over Ethernet
No PC Needed for Operation - Standalone Unit
Linux Based Operating System
Embedded Motion Detection function
SVC-3020 has an embedded sensor system that detects movements.
The observing areas of motion and sensitivity can be regulated according to the user's need.
Supports network environments
- Ethernet or Fast Ethernet interface
Easy Firmware Update through Network
- Firmware Update at remote sites is possible through Network
E-mail and FTP transmission
- SVC-3020 sends images to the designated E-mail address or FTP Server when an alarm
is raised or movements are detected.
Digital sensor TTL input
Alarm output
RS485 interface for Pan, Tilt and Zoom control
- Functions can be set remotely using an exclusive application

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
11
Image Module
▶SVC-3020
Sensitivity: 00.5Lux @40IRE, F1.2.
1/3" New Structure Super HAD Interline Transfer CCD
Digital signal processing
Superior color reproduction and very low smear
Very low noise picture quality at all illumination
▶SVC-3020-DN
Sensitivity: 0.003Lux @40IRE, built-in lens.
100x sensitivity enhancement by combination of DSS
Enhanced sharpness compensation.
Max. sense up by slow shutter is selectable to 16x/32x
Very low noise and superior picture quality.
Vari-Focal dc drive auto iris lens.
1.4. Packing Contents
SVC-3020 (DN)
MPEG4/JPEG Network Camera
UTP Cross LAN Cable CD-ROM with manual and
software
DC Adapter(12V/1A) Bracket
C-Mount Lens Adapter
Screw(3), Six Angle Wrench
Power Cable

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
12
1.5. System Requirements
Operating System : Microsoft Windows® 2000 or Windows® XP
CPU : Intel® Pentium®Ⅳ1.6Ghz or faster
RAM : 512MB or higher
VGA : AGP, Video RAM 64MB or higher
Web Browser : Internet Explorer version 6.0 or higher
Direct-X : 8.x or higher
INPUT Voltage : DC 12V / 1A
Operating Temperature: 0℃~ 50℃(32~122℉)
Humidity: 20~80% RHG, Non-Condensing

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
13
1.6. System Configuration

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
14
1.7. Physical Description and Function
1.7.1. Front View
1.7.2. Bottom View

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
15
1.7.2. Rear View
① SETTING SWITCH
▶SVC-3020
Left Right
N/A N/A N/A
FL Flickerless ON Flickerless OFF
BLC Backlight Compensation Control
OFF Backlight Compensation Control ON
ALC – ELC Auto Light Control Mode
Using Auto Iris Lens
Shutter speed 1/60
Electronic Light Control Mode
Shutter Speed 1/60~1/10,000
changeable

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
16
▶SVC-3020-DN
Left Right
DSS
Day & Night OFF Day & Night ON
D/H – D/L
* FL (Japanese
Type)
DSS Speed High
* Flickerless ON
(Japanese Type)
DSS Speed Low
* Flickerless OFF
(Japanese Type)
BLC Backlight Compensation Control
OFF Backlight Compensation Control ON
ALC – ELC Auto Light Control Mode
Using Auto Iris Lens
Shutter speed 1/60
Electronic Light Control Mode
Shutter Speed 1/60~1/10,000
changeable
② VIDEO OUT : 1Vp-p Composite, 1Channel
③ MIC. : Microphone
④ AUDIO OUT : MONO Audio Output, 1Channel
⑤ ALARM : TTL Level, Out
⑥ SENSOR : TTL Level, In
⑦RS-485 : Port for P/T/Z control.
⑧ POWER: DC12V / 1A
⑨ RESET : Initial state which is factory default
⑩ NETWORK CONNECTOR(and PoE) : RJ-45 Ethernet Connector and socket can also be used
to Power over Ethernet
⑪ ETHERNET LED : Left LED – Yellow (Link) / Right LED – Green (Act)
⑫ ACTIVATION LED :
⑬ POWER LED : Power Supply status displays (Red LED on)
⑭ DC LEVEL CONTROLLER :

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
17
2. Basic Setup of SVC-3020
2.1. How to use Lens
2.1.1. Using Auto iris Lens
1. Please peel off about 8mm of the outer skin of the auto iris lens cable.
2. Please about 2mm of the outer skin of the insulated conductor inside the lens cable.
3. Please remove the cover of the auto iris lens connection plug and solder the lens cable to the
connector pin in the plug.
Lens
- Lenses are sold separately. Lenses such as an auto iris lens, CS-Mount lens and C-mount
lens can be used.
*Note*
. Please keep the lens clean.
. Any foreign objects and finger marks on the lens can cause inferior image quality in low light
level conditions.

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
18
* SVC-3020 supports only DC iris Lens
4. Please replace the auto iris les connection plug cover and take off the CCD protection cap, and
then attach the auto iris lens to the camera by screwing it in clockwise.
5. Please insert the connection plug that is connected to the auto iris lens cable into the auto lens
connector, which is located on the side of the camera.
2.1.2. Using C-Mount Lens
Please take off the CCD protection cap and attach the C-Mount lens to the camera by screwing it in
clockwise.

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
19
2.1.3. Using CS-Mount Lens
1. Please take off the CCD protection cap and C-Mount adaptor.
2. Please attach the CS-Mount lens to the camera by screwing it in clockwise.
*Note*
- Please use the specified lens connection parts as shown in the picture below. The use of
the wrong sized parts of the wrong size may cause damage to the inside of the camera or
result in poor fitting.
- Use of a lens which is too heavy affects the balance of the camera and may cause a
malfunction. Please use a lens that weighs less than 450g.

DUAL CODEC MPEG4 NETWORK CAMERA SVC-3020 (DN) FULL MANUAL
20
2.2. Installation
•If you use Network LAN Card in your PC, you can connect the server directly to a PC with a Cross
LAN Cable provided in the package.
• On the assumption that both the user PC and SVC-3020 are used under static IP, and SVC-3020
is directly connected with the user PC or Local Network, the installation procedure is to be:
Picture 2.2 Rear View
②
③
④
①