Digital Watchdog DWC-V1362DIR User manual

ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
High Resolution
Vandal-Proof Dome Camera
DWC-V1362DIR
08092012

2
PRECAUTIONS
FCC COMPLIANCE
Do not open or modify.
Do not open the case except during maintenence and installation, for it may be dangerous and can
cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of kitchen or a boiler room, as the temperature may rise
to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference. when the equipment is operated in a residential environment. This equipment
generates, uses, and radiates radio frequency energy; and if it is not installed and used in accordance
with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.

TABLE OF CONTENTS
3
Introduction
Installation
Troubleshooting
Warranty Information
Memo 22-23
Specifications
Features
Parts and Descriptions
Dimensions
Inside the Box
Mounting the Camera
Connecting to Monitors
Adjusting the Camera Lens
4
5
6
7
8-12
13
14
17
18-19
20-21
Camera Control Board 16
Adjusting the 3-Axis Gimbal 15

4
FEATURES*
1/3” CCD
570 TV Lines [B&W], 540 TV Lines [Color]
3.3~12mm Varifocal Auto Iris Lens
100ft Range IR with Intelligent Camera Sync
Electronic Day and Night
3D-DNR (3D Digital Noise Reduction)
D-WDR (Digital Wide Dynamic Range)
HME (Highlight Masking Exposure)
SLC (Side Light Compensation)
Programmable Privacy Zones & Motion Detection
AGC / BLC / AWB
Easy Icon Driven OSD Menu with Built-in Joystick
IP66 Certified (Weatherproof)
Auto Sensing 12VDC/24VAC with Line Lock
Secondary Video-BNC Output

5
PART & DESCRIPTIONS*
1
2
3
4
5
6
7
13
12
11
10
9
8
Lens
Video Output Connector - BNC
Power Input Connector
12VDC/ 24VAC Dual Voltage
RS485: BK(D+), WH(D-)
Rubber Band
Black Dome Insert
Bubble Dome
Upper Case
Assembly Screws
T20 M4X16
NPT Plug
Bottom Case
Rubber Pad
Mounting Screws
1
23
4
5
6
7
13
12
11
10
9
8

6
DIMENSIONS IN MILLIMETERS (IN)*
109.6(4.31”)
103.1(4.06”)
41.3
(1.63”)
6.5(0.26”)
145(5.71”)
117.0(4.61”)
125.0(4.92”)
5.0(0.2”)
4.5(0.18”)
91.0(3.58”)
85.0(3.35”)

7
INSIDE THE BOX*
Included with V1 Vandal Dome Camera
1
2
3
4
5
6
7
User Manual
Mounting Template
4 Machine Screws and 4 Dry Wall Anchors
TORX-T20 Hex Key
Double-Sided TORX-T20 Hex Key
L-Key
Secondary Video-BNC Cable
7

8
MOUNTING INSTALLATION INSTRUCTIONS*
Pull wires through and make connections.
Refer to page 13. Use mounting template to
mount camera with drywall mounts and
machine screws.
Adjust the camera (pan, tilt, zoom). See
page 14 for details.
Use the joystick to adjust the OSD menu.
See pages 15-17 for details.
Attach the camera housing to the junction
box using the assembly screws.
1 2
3 4

9
JUNCTION BOX INSTALLATION INSTRUCTIONS*
Check to see all parts are in
the box.
Use the dry wall anchors and
machine screws to mount the
junction box and rubber
gasket to the wall.
Insert wires through the
wall and make the
appropriate connections.
Attach the camera to the
junction box using the
machine screws.
Attach the camera housing
to the junction box using the
assembly screws.
1 2 3
4 5

10
WALL MOUNT INSTALLATION INSTRUCTIONS*
Check to see all parts are in
the box.
Insert the wires from the
camera through the wall
mount housing.
Attach the camera to
the wall mount housing.
Use the mounting template to
make pilot holes. Use the dry
wall anchors and machine screws
to attach the assembly to the wall.
Attach the camera housing
to the fixture.
1 2 3
4 5