Samsung SIR-4260 User manual

High Resolution D/N IR Dome Camera SIR-4260 User’s Manual
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
ENGLISH

This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
◆Do NOT use power sources other than that specified.
◆Do NOT expose this appliance to rain or moisture.
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before operating the camera, confirm the camera model and correct input
power voltage. In order to that you can understand this manual thoroughly,
we will introduce our model description.
n SIR-4260 SERIES
 •NTSCMODEL •PALMODEL
  SIR-4260N  SIR-4260P
n MODEL DESCRIPTION
 •SIR-4260X
_
 •SIGNALSYSTEM
  N→NTSCMODEL
  P→PALMODEL
SIGNALSYSTEM

COLOR DOME CAMERA User’s Manual
4
COLOR DOME CAMERA User’s Manual
5
Contents Features
Indoor Visibility range 16M
IfB/Wmode,IR-LEDislighted,0Luxes'Outdoor
visibilityrange16Mguaranteesisavailable.
IRMODE Function
This function that prevent short distance
saturationincaseofIRLEDislighted,
discrimination of the subject is possible within a
short distance.
Ultra High Sensitivity
Thebuilt-inhighsensitivityCOLORCCD
producesaclearimageevenin0Lux(B/W,
IR-LEDON)orlowerillumination.
DAY&NIGHT(ICR)
This camera has a function that automatically
selects the mode that is appropriate for daytime
ornight-timeconditions.
TheCOLORmodeoperatesindaytimeconditions
to provide optimum colors, and BW mode
operatesinnight-timeconditionstoenhancethe
definition of the image.
SSNR 3 (Samsung Super Noise
Reduction) Function
Thehigh-performanceW-VDSPchip
effectivelyremoveslow-lightgainnoiseand
afterimage to provide clear images even in
dark environments.
High Resolution
Byadoptingadiagonal6mm(1/3")410,000
(NTSC)pixel,470,000(PAL)pixelSONYCCD,
the camera produces clear picture quality with
ahorizontalresolutionof600TVlinesforcolor
andahorizontalresolutionof700TVlinesfor
BW mode.
SSDR
(Samsung Super Dynamic Range)
For images with high contrast between bright
and dark areas from difficult lighting
conditions such as backlighting, this camera
selectively illuminates darker areas while
retaining the same light level for brighter areas
to even out the overall brightness.
DIS (Digital Image Stabilizer)
TheDISfunctioncompensatesforany
camera movement, to produce more stable
pictures.
Communication
RS-485,Coaxialcommunicationmethodsare
supported.
-RS-485Communications
:SamsungTechwin,Pelco-D
-CoaxialCommunications
:PelcoCoaxitron
OSD
Thecamera’sOSDiscomplimentedby12
foreign languages.
-NTSC:Korean,English,French,Spanish,
Japanese,Portuguese
-PAL:English,French,German,Spanish,
Italian,Chinese,Russian,Czech,Polish
• Features ……………………………………………………………… 5
• Warnings & Cautions ………………………………………………… 6
• Precautions…………………………………………………………… 7
• Components and Accessories ……………………………………… 8
• Overview …………………………………………………………… 9
• Installation …………………………………………………………… 10
nInstallation  
nAdjustthepanningandtilting,rotatingwhilewatchingthemonitor  
nAdjustingvarifocallenszoomandfocus 
• Connection ………………………………………………………… 12
nConnectingToMonitor  
nConnectingToPower 
nRS-485communicationcontrol 
nUsingCoaxialCommunications 
• Operating Your Camera ………………………………………… 16
nMenuConfiguration  
nMenuSetup 
·LENS 
·EXPOSURE
·WHITEBALANCE  
·SSDR 
·BACKLIGHT  
·SSNR3  
·DAY/NIGHT 
·SPECIAL 
·EXIT  
• Troubleshooting …………………………………………………… 29
• Specification ……………………………………………………… 30

COLOR DOME CAMERA User’s Manual
6
COLOR DOME CAMERA User’s Manual
7
SamsungTechwincaresfortheenvironmentatallproductmanufacturing
stages to preserve the environment, and is taking a number of steps to provide
customerswith moreenvironment-friendly products.The Eco mark represents
SamsungTechwin’swilltocreateenvironment-friendlyproducts,andindicates
thattheproductsatisfiestheEURoHSDirective.
This information is provided to ensure your safety and to prevent any losses, financial or
otherwise.Pleasereaditcarefullyandusetheproductaccordingly.
Warnings & Cautions
* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as
anaerialladderwhileprovidingafter-salesserviceshallbeatyourexpense.
 *Separatethepowerplugduringathunderstorm.
* This product is only part of a surveillance system. Therefore, we can't compensate for material loss and/or personal
injuries by robbery, fire, natural disaster or something like this type.
Ignoring this information may
result in material loss and/or
serious personal injuries including
death.
Indicates“NeverAllowed.”
Ignoring this information may
result in material loss and/or a
slight injuries.
Indicates“NoDisassembling.”
Warning/Attention/Special Mark Messages
Precautions
Do not install under extreme
temperature conditions.
Use only under temperature conditions between
-10°C and +50°C. Provide good ventilation
when using in high temperature conditions.
Do not install in high humidity
environment.
May lower image quality.
Do not install under unstable
lighting conditions.
Severe lighting changes or flickering may
hinder normal camera operation.
Avoid touching the camera lens.
The lens is the most important component
of the camera. Be careful not to smear it
with fingerprints.
Do not drop the camera or
subject it to physical shock.
May cause a product malfunction.
Never keep the camera face to
strong light directly.
May damage the CCD.

COLOR DOME CAMERA User’s Manual
8
COLOR DOME CAMERA User’s Manual
9
Precautions
•Exposure to a spotlightoran object emitting strong lightmaycause smear or
blooming.
•Ensurethatthepowersourcecomplieswithnormalspecificationsbefore
supplying it to the camera.
•IncaseofIRLEDhasbeenlighted,donotlightendirectlyeye.
Notes
❶ SIR-4260

2 Instruction Manual

3
 Ø5 Tapping Screw 4EA 
4 Quick Install Guide

5Wrench

6 Template

7 DC 12V/4A Adaptor 8 POWER CABLE
9
 Installation Video Output Cable
❶
7 8
5
69
2 4
Components and Accessories
4
⓫23
5
❿❾
1
Overview
3
768
Do not expose the camera to
radioactivity.
Radioactivity exposure may damage the
CCD.
Do not expose the camera to
rain or other types of liquids.
Wipe dry any liquids. Liquids may contain
minerals that are corrosive to electronic
components.
Pan Base : control panning angle of camera
Rotate Base : control rotating angle of camera
X3.6 Vari-focal Lens Module
Flush Housing
Pan Base Holding Screws (Color : Ivory) : fix panned position
Video output terminal
RS-485 Control terminal :The detailed decription refers to p14.
Power input terminal
Video Output Terminal to Monitor
Function Setup switch : display the menu on the screen and move the
cursor to four directions to confirm status or after
changing a selected item.
Dome Cover

COLOR DOME CAMERA User’s Manual
10
COLOR DOME CAMERA User’s Manual
11
Installation
Installation
Adjust the panning and tilting, rotating while watching the monitor
1) Remove the dome cover and shield case from the main body by loosening
the three dome cover screws.
2) And then remove the main body from mounting bracket by the four main body screws.
MountingBracket
MainBody(Camera)
DomeCover
73°
-170°
145° 195°
170°
PanBase
Tilt Base
RotateBase
•Theinstallationshouldbedonebyqualifiedservicepersonnelorsysytem
installers.
•Iftheceilingmaterial is not strong enoughtoholdthe installation screws,the
cameramayfalloff.Reinforcetheceilingasneeded.
•Takecarenottodroptheproductduringinstallation.Donotallowanyonetostand
below the installation area.
Notes
1) You can adjust camera to any direction by using Pan, Tilt, Rotate mechanism.
• Pan Base moves by 170° to each side direction and 340° on the whole.
• Tilt Base covers total 146° angle(73°to each side).
• Angle range of Rotate Base is the same as that of Pan Base. But One side
range is 195° and another is 145°
2) Methods of adjustment
• The case of wall installation
 After mounting the camera on a wall, adjusting the panning angle so that the
camera can face the direction to monitor when tilting.
 And then adjust the tilting angle by rotating the tilt base.
 Loosen the rotate base hold screw and adjust rotate base for the best
monitoring.
 Tighten the rotate base hold screw.
• The case of ceiling installation
 After mounting the camera on a ceiling, adjusting the panning angle for better
monitoring area by rotating the pan base.
 And then adjust the tilting angle by rotating the tilt base.
•Whenadjustingtherotatingangle,loosenrotatebaseholdingscrewasfollowing
FigureA.Andthentightenitagain.
•Whenadjustingthetiltingangle,justgripthetiltbaseandadjusttiltingangle.
•Whenadjustingthepanningangle,loosenpanbaseholdingscrewsasthe
followingFigureB.Andthentightenthemagain.
•2LEDsarepanedincaseofcontrolTiltangle(73°)tomaximumbutitisno
difference of visibility range performance.
Notes
•Incaseofadjustingthetilting,donottakethelensforpreventingphysicalshocks.
PleasetaketheTiltBase
RotateBaseHoldingScrew
PanBaseHoldingScrew(Color:Gold) RotateBaseHoldingScrew

COLOR DOME CAMERA User’s Manual
12
COLOR DOME CAMERA User’s Manual
13
1) Unlock the zoom(or the focus) handle to release it
2) Adjust the zoom(or the focus) handle by moving it to WIDE(NEAR) or TELE (FAR) position.
3) After adjustment, tighten the zoom(or the focus) handle, taking care that the
adjusted position does not change.
Zoom Handle
Focus Handle
Installation
Adjusting varifocal lens zoom and focus
Connection
Connection
Connecting to Monitor
CCTVCamera
Intermediate Endmonitor
Monitor
CCTVCamera
Please connect the video output
terminal located on the back of the
camera to the monitor.
• The connection method varies
depending on the type of monitor
and accessories. Please refer to
the user's manual for each
instrument.
• Please turn off the power when
connecting.
• Please select Hi-Z on the 75Ω/Hi-Z
switch for the intermediate video
TV set and select 75Ω for the
Intermediate device as shown in
the picture below.
Connecting to Power
The recommended adaptor specification
for SIR-4260 is DC 12V/4A.
Please check the standard power
requirement before connecting to power.
• As shown in the table above, voltage decreases as the wire gets longer.
Therefore use of an excessively long adaptor output line for connection to the
camera may affect the performance of the camera.
Standardvoltageforcameraoperation:DC12V±10%,AC24V±10%
There may be some deviation in voltage drop depending on the type of wire and the
manufacturer.
Whentheresistancevalueofcopperwireisat[20°C(68°F)]
•Pleasemustbeusedadaptorthatmeetsthestandardrequirement.
•Pleaseconnectthepowerafterinstallation.
Notes
Copperwiresize(AWG)
#24(0.22㎟) #22(0.33㎟) #20(0.52㎟) #18(0.83㎟)
Resistancevalue(Ω/m) 0.078 0.050 0.030 0.018
Voltagedrop(V/m) 0.028 0.018 0.011 0.006

COLOR DOME CAMERA User’s Manual
14
COLOR DOME CAMERA User’s Manual
15
RS-485 communication control
Using a RS-485 communication, it will be able to control the OSD menu at the
SAMSUNG TECHWIN System Controller or DVR.
(1) The case which it controls from the PC
Using a RS-485 converter, It connects to RS-485 control cable outside
camera and serial cable
EX) SERIAL PORT OF THE PC(COM1) → SERIAL CABLE → RS-485 CONVERTER →
RS-485 CONTROL CABLE
Connecting to RS-485 Control Cable
CONTROL CABLE SPEC
WHITE (TRX+) RS-485+
BLCAK (TRX-) RS-485-
Connection
•Whenyouconstructexternalcontrolsystemsforacameracontrol,pleaseuseto
theSAMSUNGTECHWINPROTOCOLorPELCO-DPROTOCOL.
•WhenyouconnectingtoRS-485controlcable,pleasepeelofftheouterskininside
theRS-485controlcable.
•IncaseofSCC-101connection,changecommunicationmodeto8-E-1at
Communicationconfigurationmenu.(Formoreinformation,refertoSCC-101
manual.)
Notes
* RS-485 Communication establishment initial value
485 Control Board Connection Port RS-485 Control Port
 
 
Item Camera ID BAUD RATE UART MODE RET PKT
Initial value 19600 8-NONE-1 ENABLE
(2)The case which it controls from the DVR or System Controller
It connects the RS-485 control cable in the connection terminal of 485 control
boards which are connected with the DVR or System Controller.
• Coaxial Communications System
• OSD Control method
Matrix/DVR
Using Coaxial Communications
Controller Button Camera Button
IRIS OPEN SET KEY
JOYSTICK UP UP KEY
JOYSTICK DOWN DOWN KEY
JOYSTICK LEFT LEFT KEY
JOYSTICK RIGHT RIGHT KEY
Distance Recommended Cable Specification
300m 3C2V(RG-59/U)
450m 5C2V(RG-6/U)
600m 7C2V(RG-11/U)
– Video Cable
The camera's video output port is connected to the monitor with a BNC coaxial cable,
shown below : If the distance between the camera and the monitor exceeds the
recommended maximum, please use an auxiliary video amp.
•Ifthecameraiscontrolledthroughcoaxialcommunication,pleaseuseavideoamp
intendedforcoaxialcommunications.Regularvideoampsdonottransfercoaxialsignals.
Notes
WHITE (TRX+) BLACK (TRX
-
)

COLOR DOME CAMERA User’s Manual
16
COLOR DOME CAMERA User’s Manual
17
Operating Your Camera
MAIN MENU
LENS DC
EXPOSURE BRIGHTNESS
 SHUTTER  AGC 
SENS-UP RETURN
WHITE BALANCE ATW
 OUTDOOR  INDOOR 
MANUAL  AWC→SET
SSDR OFF
 ON
BACKLIGHT OFF
 BLC  HLC
SSNR3 OFF
 ON
DAY/NIGHT COLOR
 B/W  AUTO
SPECIAL
IMAGE ADJ.  CAM TITLE  SYNC
MOTION DET  PRIVACY  DIS
COMM ADJ  LANGUAGE  RETURN
EXIT SAVE
 NOT SAVE  RESET
Menu Configuration
Use the Function Setup switch whithin the camera.
FunctionSetupswitch
Menu Setup
1. Press the Function Setup switch.
• Main setup menu is displayed on the monitor screen.
2. Select a desired function using the Function Setup switch.
• Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4. To finish the setting, select ‘EXIT’ and press the Function Setup switch.
Selectthefunctionusing
theFunctionSetupswitch.
Changethestatususing
theFunctionSetupswitch.
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
7.DAY/NIGHT AUTO
8.SPECIAL
9.EXIT SAVE
•Anitemwiththe icon also has sub menus. To select a sub menu, select an
itemwiththeiconandpresstheFunctionSetupswitch.
•Anitemwiththe---iconisunavailableduetofunctionsettings.
Notes
MAIN MENU
1.LENS DC
2.EXPOSURE
Using this function, you can control the screen brightness.
1. When the SETUP menu screen is displayed, selectLENSby using the Function Setup
switch so that the arrow indicatesLENS.
2. DC : Select Auto Iris Lens. You can adjust the minimum shutter and maximum value of
ESC shutter mode when DC Lens mode is selected.
LENS
3. Each Lens mode has sub menu items as listed below.
- Brightness : Adjusts the video brightness.
- IRIS SPEED : Adjusts the Iris control speed of the DC lens. If the control speed is too
slow or fast, please use this menu to adjust the speed.
- FOCUS ADJ. : To adjust the DC lens focus correctly, you must activate the Focus Settings
mode under each lens menu. Activate the Focus Settings mode, adjust the
lens focus, and then deactivate the settings mode.
•IfcolorrollingoccurswhenusingaDClens,setShuttertoFixed(---).
•Somelensesmaynotworkproperly,dependingonthesettingoftheBRIGHTNESSLEVEL.
Notes
ThisoperatinginstructionhasbeenwrittenoutasstandardbyF/WVersion1.0.

COLOR DOME CAMERA User’s Manual
18
COLOR DOME CAMERA User’s Manual
19
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
EXPOSURE
1. When the SETUP menu screen is displayed, selectEXPOSUREby using the Function
Setup switch so that the arrow indicatesEXPOSURE.
2. Select a desired mode using the Function Setup switch.
Operating Your Camera
•WhenyouuseaDClens,settheshuttermodetofixed(---)ifcolorrollingoccurs.
•WhentheSHUTTERissettoMANUALorA.FLKmode,SENS-UPwillbedisabled.
Notes
AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen -
but the higher the noise.
- OFF : Deactivates the AGC function.
- LOW : Allows automatic gain control from 5.3dB to 32dB.
- HIGH : Allows automatic gain control from 5.3dB to 37dB.
SENS-UP : When it is night or dark, the camera automatically detects the light level
and maintains a clear picture if this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO : Activates the SENS-UP function.
SHUTTER : You can select the shutter.
- A.FLK : Select this when you experience picture flicker, which can happen when
there is a clash with the frequency of the installed lighting.
- --- : Shutter speed is fixed at 1/60sec(1/50sec)
- MANUAL : You can control shutter speed manually.
(NTSC MODEL : 1/60~1/120,000, PAL MODEL : 1/50~1/120,000)
- ESC : Select this to control the shutter speed automatically. If ESC is selected, the
shutter speed is automatically controlled depending on the ambient
illumination of the subject.
EXPOSURE SETUP
1.BRIGHTNESS 25
2.SHUTTER ---
3.AGC HIGH
4.SENS-UP OFF
5.RETURN
•IfyoupresstheFunctionSetupswitchin‘AUTO’mode,Youcanadjustbrightness
byincreasingordecreasingtheshutterspeed.(x2~x512)
•Notethatthehigherthezoomlevel,thebrighterthescreen,butthemorelikelyit
isthatanafter-imagewillappear.
•Although Noise, Spots, andWhitish symptoms may occur in SENS-UP operation
when the zoom level is increased, this is normal.
Notes
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select ‘White Bal.’ by using the Function
Setup switch so that the arrow indicates ‘White Bal.’ .
2. Select a desired mode using the Function Setup switch.
White Balance (White Bal.)
Select one of the following 5 modes, as appropriate for your purpose.
ATW : Select this when the color temperature is between 1,700˚K and 11,000˚K.
OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K.
(sodium light inclusion)
INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K.
MANUAL : Select this to fine-tune White Balance manually. Set White Balance first
by using the ATW or AWC mode. After that switch to MANUAL mode,
fine-tune the White Balance and then press the Function Setup switch.
AWC SET : To find the optimal luminance level for the current environment, point
the camera towards a sheet of white paper and press the Function Setup
switch. If the environment changes, readjust it.
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
RETURN : Select this to save the changes in the EXPOSURE menu and return to the
SETUP menu.
•WhiteBalancemaynotworkproperlyunderthefollowingconditions.Inthiscase
selecttheAWCmode.
❶ When the color temperature of the environment surrounding the subject is out
of the control range (e.g. clear sky or sunset).
2When the ambient illumination of the subject is dim.
3If the camera is directed towards a fluorescent light or is installed in a place
where illumination changes dramatically, the White Balance operation may
become unstable.
Notes

COLOR DOME CAMERA User’s Manual
20
COLOR DOME CAMERA User’s Manual
21
Operating Your Camera
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
SSDR (Samsung Super Dynamic Range)
SSDR illuminates darker areas of an image while retaining the same light level for brighter areas
to even out the overall brightness of images with high contrast between bright and dark areas.
SSDROFF
1. When the SETUP menu screen is displayed, select ‘SSDR’ by using the switch so that
the arrow indicates ‘SSDR’.
2. Use the switch to change the SSDR level according to the contrast between bright
and dark areas.
SSDRON
BACKLIGHT
Unlike conventional cameras, the SIR-4260 is designed so that it delivers a distinctive
subject and background at the same time, even when the subject is in backlight, by
adopting a proprietary W-V DSP chip.
1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Function
Setup switch so that the arrow indicates ‘BACKLIGHT’.
2. Select a desired mode using the Function Setup switch depending on the camera purpose.
BLC : Enables a user to directly select a desired area from a picture, and to view the
area more clearly.
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
BLCON BLCOFF
HLC (High Light Compensation) :
If the scene contains extremely brightly light areas such as; from car headlight, the
light can mask out much of the on-screen detail. Using Samsung Techwin's HLC
feature to remove exceptionally brightly light areas allows details such as car
number plates to become visible.
- LEVEL : Adjust level of the HLC function.
- LIMIT : Enable to change the operating condition.
- MASK COLOR/TONE : Change the color / transparency of the masking area.
(Black, Red, Blue, Cyan, Magenta)
- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced
HLCMASKINGAREA
HLCON HLCOFF
OFF : Not being used
3. Select a desired mode using the Function Setup switch and press the SET button.
Select ‘BLC’ to adjust the area to be
enhanced then adjust the level.
HLC : Enable the user to change the level,
limit, mask color/tone and area.

COLOR DOME CAMERA User’s Manual
22
COLOR DOME CAMERA User’s Manual
23
Operating Your Camera
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select ‘SSNR’ by using the Function
Setup switch so that the arrow indicates ‘SSNR’ .
2. Select a desired mode using the Function Setup switch.
OFF : Deactivates SSNR. Noise is not reduced.
ON : Activates SSNR so that noise is reduced.
SSNR3
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
7.DAY/NIGHT AUTO
3. Set the SSNR mode to ‘ON’ and press the Function Setup switch. Then you can
adjust the noise reduction level.
•YoucannotsettheSSNRto‘ON’or‘OFF’whentheAGCmodeoftheEXPOSURE
menuis‘OFF’.
•WhenadjustingthenoisereductionlevelintheSSNRmode,rememberthatthe
higher the level set, the more the noise level will be reduced, as will the
brightness of the image.
Notes
•For effectivelicense plate observation,it needsminimumillumination and fast shutter
speedfasterthan1/200sec.
•BecausetherecanbeadifferenceintheeffectivenessofHLCaccordingtotheamountof
lightareainthescreen,optimizetheinstallationangleforthebestHLCperformance.
• Whendark,theHLCisonlyactivatedwhenabrightlightexceedingaspecificsize.inNIGHTONLYmode.
• TheHLCisnotactivatedindaylightorwhenbrightlightisnotpresentatnight.inNIGHTONLYmode.
Notes
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Function
Setup switch so that the arrow indicates ‘DAY/NIGHT’ .
DAY/NIGHT
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
7.DAY/NIGHT AUTO
8.SPECIAL
2. Select a desired mode using the Left and Right buttons according to the picture display
you want.
AUTO:
The mode is switched to ’Color‘ in a normal
environment, but switches to ’B/W‘ mode when
ambient illumination is low.To set up the switching
time for AUTO mode, press the Function Setup
switch. You can turn on or off the burst signal on
B/W mode.
- DWELL TIME : You can select the duration time about
changing the day/night mode. 
5s, 7s, 10s, 15s, 20s, 30s, 40, 60s
- DURATION : You can select brightness of illumination
about changing the day/night mode.
AUTO SETUP MODE
▶DURATION FAST
DWELL TIME 5SEC
Press SET to Return
COLOR : The picture is always displayed in color.
B/W : The picture is always displayed in black and white.
-BURST MODE :You can turn on or off the burst signal on
B/W mode.
- IR MODE :
When IR LED is turned on in B/W, the objects
can be clearly identified due to the function
that decreases screen saturation of objects within a short distance.
· TOP/DOWN/LEFT/RIGHT : Adjust the range according to the location of objects.
- IR LEVEL : Select LOW when objects appears within a short distance or select
HIGH when objects appears within a long distance on the screen.

COLOR DOME CAMERA User’s Manual
24
COLOR DOME CAMERA User’s Manual
25
Operating Your Camera
• YoucannotcontroltheDAY/NIGHTmenuwhenAGCintheEXPOSUREmenuis‘OFF’.Atthistime,
theexchangebetweenDAYmodeandNIGHTmodeoperatesaslikeselecting‘COLOR’mode.
Notes
1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function Setup
switch so that the arrow indicates ‘SPECIAL’.
SPECIAL
MAIN MENU
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.SSDR OFF
5.BACKLIGHT OFF
6.SSNR3 ON
7.DAY/NIGHT AUTO
8.SPECIAL
9.EXIT SAVE
SPECIAL
1. IMAGE ADJ
2. CAM TITLE OFF
3. SYNC INT
4. MOTION DET OFF
5. PRIVACY OFF
6. DIS OFF
7. COMM ADJ
8. LANGUAGE ENGLISH
9. RETURN
2. Select a desired mode using the Function Setup switch.
IMAGE SETUP
1. V-REV OFF
2. H-REV OFF
3. D-ZOOM OFF
4. FONT COLOR WHITE
5. SHARPNESS ON
6. MONITOR LCD
7. RETURN
IMAGE ADJ. :
1) When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the Function
Setup switch so that the arrow indicates ’IMAGE ADJ‘.
2) Select a desired mode using the Function Setup switch.
•V-REV : You can flip the picture vertically on the screen.
•H-REV : You can flip the picture horizontally on the screen.
• D-ZOOM : You can use a digital zoom of x1 ~ x16.
• FONT COLOR :
You can change the OSD font color. (White, Yellow, Green, Red, Blue)
•SHARPNESS :
As you increase this value, the picture outline becomes stronger and clearer. Adjust
this value appropriately depending on the sharpness of the picture.
•Monitor : Please change the settings value of video
appropriate to your monitor.
- LCD : Please select this menu item when using an LCD monitor.
- CRT : Please select this menu item when using a CRT monitor.
- USER : Please use this menu item when using a monitor
other than standard ones. You can change the
gamma, PED level, and color gain in the sub menus.
•RETURN : Select this to save the settings for the IMAGE ADJ. menu and to return to
the SETUP menu.
* The brightness of illumination is changeable
by installed environment.
Color →B/W B/W →Color
Fast 2.5 lux 5 lux
Slow 1 lux 10 lux
CAM TITLE : If you enter a title, the title will appear on the monitor.
1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the
arrow indicates ‘CAM TITLE’.
2) Set it to ‘ON’ by using the Function Setup switch.
•WhentheV-REVorH-REVmodeisenabled,thetextonthescreendoesnotflip.
•IfyouincreasetheSHARPNESSleveltoohigh,thepicturemaybecomedistorted
or noise may appear.
Notes

COLOR DOME CAMERA User’s Manual
26
COLOR DOME CAMERA User’s Manual
27
Operating Your Camera
5) Enter a title, move the cursor to ‘POS’ and press
the Function Setup switch. The entered title
appears on the screen. Select the position to
display the title on the screen by using the
Function Setup switch and press the Function
Setup switch. When the position is determined,
select ‘END’ and press the Function Setup switch
to return to the SPECIAL menu.
FRONT DOOR
•WhentheCAMTITLEmenuis‘OFF’,notitlewillbedisplayedonthemonitorscreeneven
if you enter one.
•OnlyEnglishisavailableinthismode.
•If you move the cursor to CLR and press the Function Setup switch, all the letters are
deleted. To edit a letter, change the cursor to the bottom left arrow and press the Function
Setupswitch.Movethecursoroverthelettertobeedited,movethecursortotheletterto
beinsertedandthenpresstheFunctionSetupswitch.
Notes
SYNC : In areas where the supply is at 60Hz, you can
synchronize the output phase of multiple cameras
using the power synchronization function (Line-
Lock) without using a synchronization signal
generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
• Press the Function Setup switch.
• You can select a desired phase from 0 to 359 when select 'phase'.
•WhenusingACpowerat60Hzfrequency,youcanusetheL/Ltypesynchronization.
•WhenthepowerisDC12V,theSYNCmenuisfixedtothe‘INT’mode.
Notes
MOTION DET :
This product has a feature that allows you to observe
movement of objects in 8 different areas on the screen,
and the words 'MOTION DETECTED' appear on the screen
when movement is detected.
you can monitor activity more efficient.
1 ) When the SPECIAL menu screen is displayed, press the
Function Setup switch so that the arrow indicatesMOTION DET.
2) Set up the mode using the Function Setup switch.
- SENSITIVITY : You can select up to 8 MD areas.When SENSITIVITY number is high, motion
detection sensitivity is increased to recognize even small movement.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- FILLSET : Fills in a selected MD area. Fills in a selected MD area. The color of filling is
sequentially selected as brown, orange, blue, cyan, yellowish green, yellow
and red.
- RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu.
PRIVACY : Mask an area you want to hide on the screen.
3) Press the Function Setup switch.
4) Use the Function Setup switch to move
to a desired letter and select the letter
by pressing the Function Setup switch.
Repeat this to enter multiple letters.
You can enter up to 15 letters.
PRIVACY AREA SETUP
1. AREA AREA1
2. MODE OFF
3. MASK COLOR GREEN
4. MASK TONE 1
5. TOP 39
6. BOTTOM 79
7. LEFT 13
8. RIGHT 51
9. RETURN
1)  When the SPECIAL menu screen is displayed, press the Function Setup switch so that
the arrow indicates ‘PRIVACY’.
2)  Set up the mode using the Function Setup switch.
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
CLR POS END

COLOR DOME CAMERA User’s Manual
28
COLOR DOME CAMERA User’s Manual
29
Operating Your Camera
COMM ADJ (Communication Adjustment) :
This function sets up the camera communication status when controlling the camera
through an external control device.
1) When the SPECIAL menu screen is displayed, press the Function Setup switch
so that the arrow indicates ‘COMM ADJ’.
2) Set up the mode using the Function Setup witch.
- AREA SEL :You can select up to 12 PRIVACY areas.
- MODE : Determines whether to use the area selected in the AREA SEL.
- MASK COLOR : Determine area color. You can select Green, Red, Blue, Black,White, Gray.
- MASK TONE : Adjust the brightness of MASK COLOR.
- TOP/BOTTOM/LEFT/RIGHT :Adjust the size and position of the selected area.
- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.
- CAM ID :Determines the camera's identification
number (between 0 and 255).
- BAUD RATE :You can select 2400/4800/9600/19200
/38400/57600 bps.
- UART MODE : You can select NONE, EVEN or ODD
for the parity bits.
- RET PKT : Determines whether to send a command back to the controller device when
a communication control command is sent to the camera.
- DISP CAM ID : Display camera title on top left corner of the screen.
* Initial value of communication adjustment
Item Camera ID BAUD RATE UART MODE PET PKT
Initial value 19600 8-NONE-1 ENABLE
Select a desired EXIT mode using the Left and Right buttons depending on the camera purpose.
- SAVE : Save the current settings and exit the MAIN SETUP menu.
- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.
- RESET : Resets the camera settings to the factory defaults. Language and Monitor
settings are not initialized.
LANGUAGE : You can select the menu language according to your requirements.
RETURN : Select this to save the SPECIAL menu settings and return to the MAIN
SETUP menu.
EXIT
Troubleshooting
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
● Nothing appears on the screen.
▶ Check that the power cord and line connectionbetween the camera and monitor are
fixed properly.
▶ Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
● The image on the screen is dim.
▶ Is lens stained with dirt? Clean your lens with soft, clean cloth.
▶ Set the monitor to proper condition.
▶ If the camera is exposed to too strong light, change the camera position.
● The image on the screen is dark.
▶Adjust the contrast feature of the monitor.
▶If you have an intermediate device, set the 75Ω/ Hi-z properly.
● The camera is not working properly, and the surface of the camera is hot.
▶Check that you have properly connected the camera to an appropriate power source.
● The SENS-UP function does not work.
▶Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’.
● The Motion Detection function does not work.
▶Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’.
● Color is not correct.
▶Check the setting of WHITE BAL SETUP menu .
● The screen flickers continually.
▶Check that direction of camera turns toward the Sun.
● When coaxial communication is not available:
▶ Make sure that the camera and monitor are installed within the recommended distance.
▶Use the video amplifier equivalent to coaxitron if the recommended installation
distance is exceeded.
•AstheDISfunctionusesthedigitalzoomthecamera'sresolutionwilldecrease.
•DISdoesn’toperatewhenbackgroundilluminationistoolow.
•DISdoesn’toperatewhenobjectpatternismonotonicaslikeskyorwhitewall.
Notes
DIS (Digital Image Stabilizer) :
This function mitigates any picture movement due to external factors such as wind.

COLOR DOME CAMERA User’s Manual
30
COLOR DOME CAMERA User’s Manual
31
SIR-4260N SIR-4260P
ELECTRICAL
Input Voltage DC 12V / AC 24V
Power Consumption Max 4.5W (LED ON)
VIDEO
Imaging Device 1/3 inch, Diagonal 6mm Super HAD CCD
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Scanning System 2:1 Interlace
Synchronization Internal /Line-Lock
Frequency H : 15.734KHz V:59.54Hz H: 15.625KHz V: 50.00Hz
Horizontal Resolution COLOR : 600TVL, B/W : 700TVL
Min. Illumination 0.15 Lux(50IRE, No SENS-UP) / 0.0003Lux(SENS-UP) / 0Lux (IR-LED ON)
S/N (Y Signal) 52dB (Weight On, AGC Off)
Video Output CVBS : 1.0Vp-p, 75Ω composite
LENS
Zoom Ratio 3.6x (Manual)
Focus Length 2.8 ~ 10.0mm (F1.2)
Angular Field of View H : 94.4°(Wide) ~ 28°(Tele) / V : 69.2°(Wide) ~ 21°(Tele)
IR LED (Distance) 10EA (16m)
PAN / TILT / ROTATE
Pan / Tilt / Rotate Range 0° ~ 340° / 0° ~ 146° / 0° ~ 340°
OPERATIONAL
Electronic Shutter Speed ESC, Fixed, FLK, Manual (1/60 ~ 1/120k) ESC, Fixed, FLK, Manual (1/50 ~ 1/120k)
On Screen Display
NTSC : Korean,English,Japanese,Spanish,French,Portuguese
PAL : English,French,German,Spanish,Italian,Chinese,Russian,Polish,Czech
SSDR On / Off (Level adjustable)
Backlight Compensation BLC / HLC / OFF
Day & Night COLOR / BW / AUTO (ICR)
Gain Control Low / High / Off
White Balance ATW / Manual / AWC / Outdoor / Indoor (1,700°K ~ 11,000°K)
SENS-UP (frame Integration) Auto /Off (Selectable x2 ~ x512)
Motion Detection On / Off (8 Programmable zones)
Privacy Masking On / Off (12 Programmable zones)
3D Noise Filter (SSNRIII) On / Off (Level adjustable)
Digital Zoom On / Off (x1 ~ x16)
Digital Image Stabilization(DIS) On / Off
Camera Title Off / On (Displayed 15 Characters)
Sharpness On / Off (Level adjustable)
Flip / Mirror On / Off
Communication Coaxial, RS-485
Protocol Coaxial(Pelco), RS-485(STW, Pelco-D)
ENVIRONMENTAL
Operating Temperature / Humidity -10°C ~ +50°C / 30% ~ 80% RH
Storage Temperature / Humidity -20°C ~ +60°C / 20% ~ 90% RH
MECHANICAL
Water Resistance IP66
Dimension Ø148 x 126 mm
Weight 1.3Kg
Specifications
The specification for this product may change without prior notice for product improvement.
DECLARATION OF CONFORMITY
ApplicationofCouncilDirective(s) 89/336/EEC
Manufacturer'sName SAMSUNGTECHWINCO.,LTD
Manufacturer'sAddress SAMSUNGTECHWINCO.,LTD
 42,SUNGJU-DONGCHANGWON-CITY,
 KYUNGNAM,KOREA,641-716
EuropeanRepresentativeName
EuropeanRepresentativeAddress
EquipmentType/Environment CCTVCamera
ModelName SIR-4260P
BeginningSerialNO. C10S7010007
YearofManufacture 2009.07.01
Conformanceto EN50081-1:1992
 EMC-Directive89/336EECand92/31/EEC
 EN50130-4:1996
We, the undersigned, hereby declare that the equipment specified above conforms
totheaboveDirective(s).
Manufacturer SAMSUNGTECHWINCO.,LTD LegalRepresentativeinEurope
Signature  Signature
FullName BONJENGGU FullName
Position QUALITYCONTROLMANAGER Position
Place CHANGWON,KOREA Place
Date 2009.07.01 Date

P/No. : Z6809-0107-01A
VAN 09. 07
www.samsungtechwin.com
www.samsungcctv.com
•SAMSUNG TECHWIN CO., LTD.
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703
TEL : [phone]~8 FAX : [phone]
•SAMSUNG TECHWIN EUROPE CO., LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : [phone] FAX : [phone]
•SAMSUNG TECHWIN AMERICA Inc.
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : [phone] FAX : [phone]
www.samsungcctvusa.com
SALES NETWORK