Serpent 9*50r User manual

Instruction Manual

2
Congratulations on your newly-acquired Serpent
950R. You have chosen the highest quality, ulti-
mate-performance racecar that is easy to use,
assemble, and set up. As part of the worldwide
team of Serpent drivers, you will also get superior
technical support. Serpent has a tradition of excel-
lence with instruction manuals, and with the new
Serpent 950R manual we have yet again gone a
step further. The new layout has easy to follow
step-by-step assembly instructions and building
tips, richly illustrated with 3D rendered full-color
images. Following the instructions will result in a
well-built, high-performance racecar that will soon
be able to unleash its full potential at the racetrack.
Instructions
This instruction manual has nine sections that will
lead you through the assembly process of your
Serpent 950R. Follow the assembly steps in the
order presented to ensure that no problems occur
during assembly. Each step indicates all the fasten-
ers and small parts used. Bag numbers are also
shown to identify the kit bag that contains the
appropriate parts for the step.
Set-up
In certain assembly steps you need to make basic
adjustments, which will give you a good initial set-
up for your Serpent 950R. Note that fine-tuning the
initial set-up is an essential part of building a high-
performance racecar like your Serpent 950R.
The Set-up Guidelines in Section 9 of this instruc-
tion manual will help you to adjust your Serpent
950R. It is very important to follow these proce-
dures, and be accurate with your adjustments not
only now, but every time you prepare the car for
practicing or racing. This is how the best drivers in
the world do it - simple, straight forward, and accu-
rate!
Exploded views and parts list
The exploded views and parts lists for the Serpent
950R are contained in a separate Reference Guide.
The exploded views show all the parts of a particu-
lar assembly step, together with the Serpent part
number. The parts lists at the end of the Reference
Guide indicate the part number and name of each
part for easy reference when re-ordering.
Safety precautions
Included with your Serpent 950R kit is a document
entitled “Read This First” that covers safety precau-
tions for the assembly and use of this product. We
strongly recommend that you thoroughly read and
understand that document, and follow all the pre-
cautions.
Section Page
1.0 Shock Assembly 4
2.0 Front Assembly 7
3.0 Rear Assembly 12
4.0 Radio Plate Assembly 16
5.0 Radio Plate Mounting 18
6.0 Gearbox Assembly 21
7.0 Centax Assembly 23
8.0 Final Assembly 26
9.0 Set-up Guidelines 29
Introduction
Contents
PERFORMANCE THROUGH EVOLUTION

3
Length after assembly.
Using the manual
Each step contains a variety of numbers, lines, and symbols. The numbers represent the order in which
the parts should be assembled. The lines and symbols are described below.
Line/Symbol Description
Assembly path of one item into another.
Group of items (within lines) should be assembled first.
Direction the item should be moved.
Glue one item to another.
Press/Insert one item into another.
Connect one item to another.
Gap between two items.
OW
Apply graphite grease (GR), threadlock (TL) or Serpent’s One-way Lube
(OW). (items not included).
myTSN.com
The printed instruction manual included with your
Serpent 950R kit is very complete, though due to
continuous product development, more up-to-date
information is provided at our myTSN.com web
portal. This state-of-the-art R/C technology portal
is where Serpent racers from all over the world
meet and exchange their ideas, and share useful
information and experiences about their Serpent
cars.
All information about the Serpent 950R is acces-
sible from the Serpent 950R product page on
myTSN.com. You can access this page by going to
the Products section, then search for the ‘Serpent
950R’ product name.
From the Serpent 950R product page you will find
the very latest information about your Serpent
950R: reports by team drivers and other experts,
tips and tricks, FAQ, forums, setups, image gal-
lery, downloadable files, and even streaming video
of the Serpent 950R on how to further improve the
car. The latest version of the instruction manual
(including team and racer tips, and part lists and
option lists) will be made available as download-
able PDF-files and online viewable pages under ‘i-
Manual’.
So be sure to visit myTSN.com and the Serpent
950R page. There is a world of up-to-date informa-
tion about your Serpent 950R waiting for you, and
it is just a few mouse clicks away! If you are not
yet a member of myTSN, we strongly recommend
that you sign up immediately so you can experi-
ence and enjoy an even wider range of services
from Serpent and other myTSN partners.
www.myTSN.com/Serpent950R

4
Step 1.1 Bag 01
R1
1.9mm
N3
3x6x0.3mm
R2
2.3mm
Y17
12.1x1.6mm
1.0 Shock Assembly
Front shocks: short shock shaft and body
Rear shocks: long shock shaft and body
Remove plastic flashing for smooth
movement of pistons. Tab in upper piston
fits in notches in lower piston
R2
N3
4
R1
Y17
3
2
1
2
1
Step 1.2
Step 1.3
Lubricate shock shaft with shock oil
before inserting in shock body.

Y3
3x1.5mm
5
Fill the shock body with shock oil, with the piston at
the bottom.
Bleeding
Let the oil settle and allow the air to escape. Slowly
move the piston up and down to release any trapped
air bubbles. Repeat as necessary until no bubbles
appear.
Grip shock rod at top of exposed threads with side
cutting pliers. Be sure not to damage the shock rod.
Y3
Step 1.4
Step 1.5
Step 1.6
1
2
Lubricate O-ring with shock oil before
sliding onto shock shaft.
Hint: Pre-thread ball-joint with M3
screw for easy assembly

6
4
32
1
hardest
softest
Damping adjustment
Pull the shock shaft all the way out, turn
slightly to lock it in the shock body.
Adjust the shock damping by rotating the
shock shaft CW or CCW to positions 1-4.
Each setting can be felt by a slight “click”.
IMPORTANT! Each pair of front and rear
shocks must have the same damping set-
ting.
Front Shocks: short shocks and springs
Rear Shocks: long shocks and springs
Shock length adjustment
Check the length of the shocks in the
extended, fully locked position.
Front shocks: 67.5mm
Rear shocks: 76.5mm
Adjust shock length with the ball-
joint.
IMPORTANT! Each pair of front and
rear shocks must be the same length.
Line up
notch
Step 1.7
Step 1.8
1
23
4
1
2
2 Holes
3 Holes
4 Holes
5 Holes

7
Y13
10.3x1.8mm
G19
M4x10mm
2.0 Front Assembly
U13
12x18mm
Step 2.1
Step 2.2
1
2
2
3
3
2
2
4
Bag 02, UI,
Tools D938
Bag 03
G19
G19
G19
G19
OW
OW
3
Looser
Default
Tighter
Change the position of BOTH
eccentric hubs to adjust front belt
tension. Both hubs should have
the same position.
E28
3x14mm
1
1
Depending on the set front track width ensure
that there is no excessive play in the drive-
shafts by placing these spacers.
E28
E28
U13 Y13
U13

8
G19
M4x10mm
E11
M3x8mm
B13
3.5x13mm
U6
6x13mm
1.2mm
Step 2.3
Step 2.4
1
2
3
4
3
1
1
2
Bag 04
E11
E11
E11
G19
U6
U6
B13
B13
B13
B13
Bag 05

H16
4x4mm
R5
5mm
R7
7mm
G19
M4x10mm
E10
3x6mm
H16
4x4mm
9
Step 2.5
Step 2.6
Step 2.7
1
2
3
4
5
6
2
1
3
6
1
5
2
Bag 06
Bag 07
R5
R7
H16
H16
R7
G19
G19
H19
H19
E10
H16
H19
4x10mm
Firmly press all eight inserts
into both bulkheads.
1
1
1
Assemble both front lower arms using the indicated steps.
Note the orientation of the inserts,
ensure that the front and back are the
same top and bottom.
4mm
4

E15
3x20mm
H17
4x6mm
E10
3x6mm
P10
2.5x22mm
U14
12x21
10
Step 2.8
Step 2.9
Step 2.10
1
2
2
4
4
3
3
1
2
3
1
1
2
3
5
6
4
Bag 08
Bag 09,10
E15
E15
H17
H17
H16
P10
U14 U14
E10
H16
4x4mm Assemble both front upper arms using the indicated steps.
Press spring into end
of front axle until it
snaps into place.
Assemble both steering blocks using the indicated steps.
4mm
4mm
2mm
1mm
Caster Spacer placement
The left steering block
can be distinguished
by 4 dots.
*Used to set
wheelbase

11
Step 2.11
Step 2.12
1
IMPORTANT! Ensure the front suspension moves up and down freely without binding.
1:1
88.5mm
3.3mm
0.5mm

12
G19
M4x10mm
P10
2.5x22mm
Q14
3x16mm
R5
5mm
B13
3.5x13mm
G19
M4x10mm
H16
4x4mm
P12
3x12mm
3.0 Rear Assembly
Roughen the metal plates with
sandpaper before gluing
U8
6x15mm
U14
12x21mm
U8
6x15mm
Step 3.1 Bag 11,12
Step 3.2 Bag 13,14
1
2
3
4
5
6
7
8
9
10
2
1
4
6
3
10
9
8
7
5
12
13
1
P10
U14
U14
R5
G19
G19
Q14
P10
B13
B13
B13
B13
G19
G19 G19
R5
H16
H16 P12
U8
Q14
P10
R5
5mm
11
Press pins into chassis so
they are flush with bottom
11

13
B13
3.5x13mm
E11
3x8mm
G19
M4x10mm
E11
3x8mm
NN4
3.2x9x0.1mm
1.3mm
47.5mm
1:1
H13
3x12mm
H19
4x10mm
H22
4x20mm
H16
4x4mm
Use the special tool supplied
to install the alu pivot ball
into the wishbone ball-point.
Important! Ensure the rear suspension
moves up and down freely without binding.
Do not overtighten the anti-roll bar mounting
screws.
Step 3.3 Bag 15,16
Step 3.4 Bag 17
1
3
2
3
1
2
3
4
4
4
H22
E10
H19
E11
H13
G19
G19
B13
B13
B13
B13
E11
E11 NN4
NN4
1
56
7
8
9
10
11
12
13
14
H16
4
2
E10
3x6mm
Screw setscrew H22 into the
wishbone ball joint until no
more than 11mm of the set-
screw remains visible

14
P10
2.5x22mm
G21
M4x16mm
18.6mm
17.6mm
Rear
Front
U14
12x21mm
Step 3.5 Bag 18,19
Step 3.6
1
2
1
U14
U14
P10
G21
2
4
3
5
Assemble both rear hubs using the indicated steps.
Press spring into end
of rear axle until it
snaps into place.

15
E10
3x6mm
E15
3x20mm
E13
3x12mm
E14
3x16mm
R2
2.3mm
Step 3.7 Bag 20
Step 3.8 Bag 21
2
1
4
4
3
11
3
1
2
2
3
4
E15
E15
G11
E10
E10
E13
R2
E13
R2
E14
E14
G11
3x8mm

16
C5
2.5x8mm
E11
3x8mm
4.0 Radio Plate Assembly
The number on the servo arm corresponds
to the number of teeth.
23 - Sanwa / KO / JR
24 - Hitec
25 - Futaba
Step 4.1 Bag
22,23,24
Step 4.2 Bag 25
1
2
3
4
5
1
3
6
2
5
4
7
E28
C5
E11
E28
E28
E28
E28
E28
R4
E10
E11 E10
E11
E11
3x8mm
E28
3x14mm
R4
4mm
Steering Servo
Output gear of steering servo must be
towards the FRONT of car.
Throttle Servo
Output gear of throttle servo must
be towards the REAR of car.
Throttle Linkage
42.4mm
Steering Linkage
46.5mm
1:1
1:1
Ensure free movement of part
E10
3x6mm

17
E28
3x14mm
G19
M4x10mm
E13
3x12mm
E11
3x8mm
Step 4.3
Step 4.4
Step 4.5 Bag 26
Note. For clockwise circuits with mostly
right hand corners the fuel tank lid nip-
ple should be placed on the right side of
the lid and the grubscrew on the opposite
side. The opposite is true for anti clock-
wise tracks with mostly left hand corners.
Important! Check that the fuel line and
pressure line are free from debris and not
blocked
3
1
2
1
2
3
4
1
5
5
2
G19
G19 G19
G19
E13
E13
E11
E11
H9
E28
H9
3x4mm
Securely attach receiver to mounting plate.

18
5.0 Radio Plate Mounting
G19
M4x10mm
Step 5.1 Bag 27
Step 5.2
1
2
3
45
1
3
4
2
G19
G19 G19
G19
G19
G19
G19
G19
G19
G19
G19
G19
G19
G21
G19
G19
G19
G19
G21
G19
G19
G19
M4x10mm
G21
M4x16mm
Steering
linkage
Servo saver
Securely attach a AAA 5-cell receiver
battery pack to the battery tray.
Note: Serpent offers the pre-built
5-Cell battery set (#902126) for the
Serpent 950R. For more information,
see the appropriate product page on
myTSN.com

19
H17
4x6mm
Step 5.3
Step 5.4 Bag 28
1
2
2
1
2
2
H17
H17
Alternative: Serpent offers the #902160 Push-Rod Front
Suspension Set as an alternative suspension system for the
950R. For more information, see the appropriate product
page on myTSN.com.

20
G19
M4x10mm
LM4
M4
P13
3x13.8mm
R5
5mm
Step 5.5
Step 5.6
1
2
2
LM4
LM4
LM4
G19
G19
G19
G19
G19
A13
A13
G19
M4x10mm
A13
3.5x13mm