Seymour Z-2510 Operating manual

DIRECTIONS:
*To complete the Universal Water Blend can, ater reducible paint must be added.
*To complete the Universal Solvent Blend can, solvent based paint must be added.
1. Wear safety glasses.
2. Detach the clear plastic plunger attachment from the top of the cap.
3. Slide open the Fill One door, then firmly press the plunger attachment and mate it with the plunger. Ma e
sure the nipple is facing down.
4. Remove the clear plastic cap from the top of the fill can. Press the metal reservoir cup onto the top of the
can. Slide the cap into the metal reservoir cup, pressing down so that it mates with the bottom of the cup.
5. Pour filtered paint to the reservoir cup, leaving a 1/4 inch gap (6mm) at the top unfilled. Overfilling will
cause paint to spill out during the filling process.
6. Place the reservoir and can into the filling machine, eeping them connected at all times.
Slide the brim of the reservoir cup into the reservoir slot. Rotate the blac base countercloc wise to snug the
connection between the can and cup. Do not overtighten base.
7. Close the door, then begin cran ing the handle until it reaches its lowest position.
8. Cran the handle in the reverse direction until it reaches its highest position.
9. Open the door, loosen the blac base plate, and remove the can/cup from the machine. Separate the
metal reservoir cup from the can. Separate the plastic cap from the reservoir by hand or by pressing the cup
down on a wor surface, which will release the cap.
10. Insert sprayhead using a slight twisting motion with the spray nozzle pointing away from you.
11. Sha e can vigorously for 30 seconds to mix the contents.
12. Invert the can and spray for 3 seconds to clear the valve and sprayhead. Place cap bac on the can.
13. To fill more cans with the same paint, repeat steps 1 thru 12.
Note: Since this aerosol can is incomplete ithout the addition of paint, the custom packer
assumes all responsibility for completing the filling operation as ell as the performance of the
finished product (including long term can stability).
Z-2510 Fill One Machine
This is a unique aerosol can filling machine that
lets you effortlessy fill pre-charged cans by hand.
Extremely reliable---no more replacing fatigued o-
rings and washers. The unique cap lets you avoid
messy prep and cleanup while leaving you with the
actual color inside the cap for easy reference. This
is a must have tool for paint stores and
contractors.

Using either the solvent or water blend can,
detach the clear plastic plunger attachment
from the top of the cap.
Slide open the Fillon door, then firmly
press the plunger attachment into the
plunger. Make sure the nipple is facing
down.
Remove the clear plastic cap from the top of the
fill can. Press the metal reservoir cup on top of
the can with the smallest opening resting on the
top of the fill can. Slide the cap into the metal
reservoir cup, so that it mates with the bottom of
the cup. Using your inde finger, press the bottom
of the plastic cap into the bottom of the reservoir
cup to ensure a snug fit.
Press the metal reservoir cup down firmly
onto the top of the spray can. The two
components should lock together and
stay connected.
Pour filtered paint to the reservoir cup,
leaving a quarter inch gap at the top
unfilled. Overfilling will cause paint to
spill out during the filling process.

Gently place the reservoir and can into the filling machine, keeping them
connected at all times. Slide the brim of the reservoir cup into the reservoir
slot. Rotate the black base counterclockwise to snug the connection
between the can and cup. Close door.
Close the door, then begin cranking the handle until it reaches its lowest
position, then crank the handle in the reverse direction until it reaches its
highest position. Open the door, loosen the black base plate, and remove
the can/cup from the machine. Separate the metal reservoir cup from the
can.
Separate the plastic cap from
the reservoir. Disconnect metal
reservoir cup from the top of
the can.
Insert sprayhead using a slight twisting motion with
the spray nozzle pointing away from you. Shake can
vigorously for 30 seconds to mi the contents. Invert
the can and spray for 3 seconds to clear the valve
and sprayhead. Place cap back on the can. To fill
more cans with the same paint, repeat all steps.