Shademaker SB BASE WEIGHT Series User manual

13401 Brooks Drive
Baldwin Park, CA 91706
p 626.338.8810
f 626.338.8816
[email protected]
shademakerusa.com
©2018 Shademaker. All rights reserved. SMOM-BASEPLATE-0118

Steel Base Plate Includes:
A - Bolts (4)
B - Feet (4)
C-
Steel Base Plate (1)
(Square or Round)
Required:
Hexagon Wrench
Two-person team
21
BASE ASSEMBLY
STEP 1
Remove top lid of packaging. Remove all 4 corner packaging materials from steel base plate
corners/edges (Fig. 1) while still inside box. Attach 4 feet to holes located underneath steel
base (Fig. 2) and push firmly to secure into place. Using a two-person team, lift edge of steel
base plate (Fig. 3) and turn over so steel plate base is right side up. Gently lift steel base
plate and place in desired location (Fig. 4). NOTE: Will be difficult to move once in place.
AB
C
STEP 2
For additional steel base plates, repeat Step 1 (feet are optional). Lift steel base plate and
place on top of 1st steel base plate (Fig. 5). NOTE: Make sure countersunk holes line up with
threaded holes on lower plate (Fig. 6)! Bolts will only fit one way. Attach 4 bolts into 4 large
holes (Fig. 7). Tighten with hexagon wrench (Fig. 8).
(Fig. 1) (Fig. 2)
(Fig. 4)
(Fig. 3)
STEP 3
For additional steel base plates, repeat Step 2 (feet are optional). Make sure to line up holes
and secure with bolts accordingly (Fig. 9).
You are now ready to install internal stem or adapter plate onto base! For warranty
information, please visit www.shademakerusa.com.
(Fig. 5)
(Fig. 7) (Fig. 8)
(Fig. 6)
(Fig. 9)
(Square Steel Base Shown)

Steel Base Plate Includes:
A - Bolts (4)
B - Feet (4)
C-
Steel Base Plate (1)
(Square or Round)
Required:
Hexagon Wrench
Two-person team
21
BASE ASSEMBLY
STEP 1
Remove top lid of packaging. Remove all 4 corner packaging materials from steel base plate
corners/edges (Fig. 1) while still inside box. Attach 4 feet to holes located underneath steel
base (Fig. 2) and push firmly to secure into place. Using a two-person team, lift edge of steel
base plate (Fig. 3) and turn over so steel plate base is right side up. Gently lift steel base
plate and place in desired location (Fig. 4). NOTE: Will be difficult to move once in place.
AB
C
STEP 2
For additional steel base plates, repeat Step 1 (feet are optional). Lift steel base plate and
place on top of 1st steel base plate (Fig. 5). NOTE: Make sure countersunk holes line up with
threaded holes on lower plate (Fig. 6)! Bolts will only fit one way. Attach 4 bolts into 4 large
holes (Fig. 7). Tighten with hexagon wrench (Fig. 8).
(Fig. 1) (Fig. 2)
(Fig. 4)
(Fig. 3)
STEP 3
For additional steel base plates, repeat Step 2 (feet are optional). Make sure to line up holes
and secure with bolts accordingly (Fig. 9).
You are now ready to install internal stem or adapter plate onto base! For warranty
information, please visit www.shademakerusa.com.
(Fig. 5)
(Fig. 7) (Fig. 8)
(Fig. 6)
(Fig. 9)
(Square Steel Base Shown)

13401 Brooks Drive
Baldwin Park, CA 91706
p 626.338.8810
f 626.338.8816
[email protected]
shademakerusa.com
©2018 Shademaker. All rights reserved. SMOM-BASEPLATE-0118