Courtyard Creations KFS777U- User manual

BOLT CAP
BACK ASSEMBLY
SEAT ASSEMBLY
LEFT ARM
RIGHT ARM
BOLT M6*65
BOLT M6*16
1
2
3
4
5
6
7
9
8
10
13
12
11
14
1
1
1
1
2
4
6
1
1
KFS777U-CS02-1
KFS777U-CS04-6
KFS777U-CS01-2
KFS777U-CS01-3
17C33A0706001Y4
WASHER d6.5*D13*1.0 6
17FA05040301-Y4
18000337004
PARTS LIST
PART
NO. MATERIAL CODE PART Q’ TY PART NO. MATERIAL CODE PART Q’ TY
FIGURE 1
Attention:
Make sure that each bolt needed for all steps matches the
corresponding figure to ensure proper assembly.
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
Step 1:
Place the back assembly (#1) onto a non-abrasive surface,
such as a carpet. Insert the back assembly (#1) into the seat
assembly (#2). See Figure 1.
SEAT CUSHION
PILLOW
61K777UJ00001BA
61K777UC00001BA
PAGE 1 OF 2
STOP DON’T RETURN TO STORE!
Use the correct bolts as indicated. Do not tighten any of the bolts until the chair is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings
required.
Keep children away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
!
!
!
!
!
COURTYARD CREATIONS INC.
1
1
22
17C33A0755001Y4
KFS777U-WM
17C02A0755131Y4 BOLT M6*14 2
18000337006 BOLT CAP M6 2
17KAA0101----Y4
17KAA0201----Y4
HEX.KEY WRENCH 4MM
HEX.KEY WRENCH 6MM
1
1

Cleaning and Maintenance
• Wash frame parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach, acid, or other solvents
on the frame parts.
•Cushions may be washed on the surface only by using mild soap and water or commercial foaming upholstery cleaner if
necessary. If washed, rinse well and hang to dry. Do not machine wash or dry.
•We recommend the use of furniture covers when not in use.
•Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of your bench.
•In order to prolong the life and beauty of your bench, we recommend that it be stored in a dry and protected area during off
season periods.
FIGURE 2 FIGURE 3
FIGURE 4 FIGURE 5
Step 4:
Fasten both the left arm (#3) and the right arm (#4) to the
back assembly (#1) by using bolts (#7). Make sure that all of
the bolts have been tightened completely and cover them with
bolt caps (#9 and #10). See Figure 4.
Step 5:
Place the pillow (#13) and the cushion (#14) onto the bench.
Secure the cushions to the bench by using the plastic clamps.
See Figure 5.
Note:
The labels marked “L” and “R” on the arms (#3 and #4) should
coincide with Figure 3 to ensure proper assembly.
16
#6 BOLT M6*16
1
34
123
L
2
6
68
8
10
10
4
R
14
13
Step 2:
At the rear of the seat, fasten the seat assembly (#2) to the
back assembly (#1) by using bolts (#5) and washers (#8).
Keep the bolts loose. See Figure 2.
5
9
8
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTYDURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THESTORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
Step 3:
Fasten both the left arm (#3) and the right arm (#4) to the seat
assembly (#2) by using bolts (#6) and washers (#8). Keep the
bolts loose. See Figure 3.
STOP DON’T RETURN TO STORE!
PAGE 2 OF 2
#5 BOLT M6*65
65
7
9
#7 BOLT M6*14
14