ShadeTree 20'x40' Heavy-Duty, Fire-Resistant Event Tent... User manual

SHADE TREE™ 20'x40' Heavy-Duty, Fire-Resistant
Event Tent w/Sidewalls - 500g/m2 PVC Fabric

Shade Tree 20’ x 40’ PVC Tent Part List
No.
Measurement
Table Description
Graph
Quantity
#1
62”
Galvanized Pole w/ 2
connectors
28
# 2
76”
Galvanized Pole w/ 2
connectors
62
57.5”
Reinforcement Bar for
horizontal connector
14
30”
Reinforcement Bar for
vertical connector
7

Shade Tree 20’ x 40’ PVC Tent Part List
No.
Joint Description
Graph
Quantity
A
120º 3 Way Joint
4
B
120º 4 Way Joint
10
A1
120º 3 Way Joint
w/tab
2
B1
120º 4 Way Joint
w/tab
5
A2
Straight 3 Way Joint
w/tab
4
B2
Straight 4 Way Joint
w/tab
10
C
90º 3 Way Joint
(foot plate)
4
D
180º 3 Way Joint
(foot plate)
10
E
2 Way Joints for front
and back door
4

Frame Assembly

To assemble the canopy frame, you will need to start by collecting the following
poles and connectors:
Part
Quantity
#1 Pole
28
#2 Pole
24
A Connector
4
A1 Connector
2
A2 Connector
4
B Connector
10
B1Connector
5
B2 Connector
10

Assembly Instructions
1) Start by assembling the top peak of the canopy frame with #2 poles, A1 connectors, and B1 connectors. (A1
connectors need to be positioned on the ends as shown in the diagram above.)
2) Connect the #1 poles to A1 and B1 connectors on one side.
3) Attach an A2 connector to the outside #1 pole. Then add #2 pole horizontally to the A2 connector and
connect a B2 connector to pole #1. (A2 connectors need to be positioned on the ends as shown in diagram
above.)
4) Attach an A connector on the end of #1 poles at the corners. Then attach a #2 pole horizontally and attach a
B connector on the end. Repeat steps until you reach the other corner. Complete by attaching an A
connector at the corner.
5) To finish the other side repeat steps 2 through 4.

Support Bar Installation

To assemble the support bars, you will need to start by collecting the following parts:
Parts
Quantity
Short Bolts with Nuts
28
57.5” reinforcement bar
14
30” reinforcement bar
7
6) Attach a 57.5” reinforcement bar to each A2 connector. Then connect the rest of the 57.5” reinforcement
bars to each B2 connector using a nut and bolt. (You will not want to tighten the nuts and bolts until all are
installed)
7) Attach one end of each 30” reinforcement bar to each A1 and B1 connector using a nut and bolt.
8) Bringing the ends of the three bars together, connect using a nut and bolt.
9) Once everything is connected, tighten all nuts and bolts.

Assembling Leg Poles
10) Attach # 2 poles to 2 of the outside corners (A connectors)
11) Attach # 2 poles to all B connectors on the same side as used in step 10.

Attach Canopy to Roof
12) Drape canopy over entire roof structure.
13) Using the bungee balls, connect the canopy to the poles from inside the tent.

Final Leg Pole Assembly
14) Repeat steps 10 & 11 for installing the remainder of the leg poles.
15) Attach a C connector to each #2 pole
16) On the long sides of the tent, install a D connector to each #3 pole. Install a #2 pole between each
connector
17) On the short sides, install a #2 pole to each C connector. To connect the poles in the center, install an E
connector locking each #2 pole into the connector.

Attaching Sidewalls and End Walls
18) Hold sidewalls in place while using bungee balls to attach the panels to the poles.