Shark UltraLight POWERFINS HZ600 Series User manual

UltraLight PowerFins™
Corded Stick Vacuum with
Self-Cleaning Brushroll
HZ600 Series
OWNER’S GUIDE

sharkclean.com
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM
1. Inspect power cord and plug for any
damage before use. DO NOT use
vacuum cleaner with a damaged
cord or plug. Turn off all controls
before plugging in or unplugging
the vacuum cleaner. Store your
vacuum cleaner with the power cord
secured around the two cord hooks.
To minimize the risk of power cord
damage, do not allow the motorized
brush roll to ingest the cord. If this
occurs, immediately shut off power
to the vacuum and remove the cord.
2. This appliance has a polarized plug,
if the plug does not fit fully into the
outlet, reverse the plug (one blade is
wider than the other). If it still does
not fit, contact a qualified electrician.
DO NOT force into outlet or try to
modify to fit.
3. Your vacuum cleaner may consist of
a motorized nozzle, wand, hose, and/
or vacuum pod. This device contains
electrical connections, electrical
wiring, and moving parts that
potentially present risk to the user.
4. Use only identical replacement parts.
5. Carefully observe and follow the
instructions provided below to avoid
improper use of the appliance.
DO NOT use the vacuum for any
purpose other than those described
in this manual.
6. Before use, carefully inspect all parts
for any damage. DO NOT use if any
parts are damaged.
7. The use of an extension cord is
NOT recommended.
8. This vacuum cleaner contains
no serviceable parts.
9. This appliance can be used by
persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Cleaning and user maintenance
shall not be made by children. Keep
the appliance and its cord out of
reach of children. DO NOT allow the
appliance to be used by children. DO
NOT allow to be used as a toy. Close
supervision is necessary when used
near children.
10. Always turn off the vacuum cleaner
before connecting or disconnecting
any motorized nozzles or other
accessories.
11. DO NOT handle plug or vacuum
cleaner with wet hands.
12. DO NOT use without filters in place.
13. Only use Shark® branded filters
and accessories.
14. DO NOT damage the power cord:
a) DO NOT pull or carry vacuum
cleaner by the cord or use the
cord as a handle.
b) DO NOT unplug by pulling on
cord. Grasp the plug, not the cord.
c) DO NOT run the vacuum cleaner
over the power cord, close a door
on the cord, pull the cord around
sharp corners, or leave the cord
near heated surfaces.
WARNING
To reduce the risk of fire, electric shock, injury, or property damage, when using
an electrical appliance, basic precautions should always be followed, including
the following:
IMPORTANT SAFETY INSTRUCTIONS
FOR HOUSEHOLD USE ONLY

sharkclean.com
15. DO NOT put any objects into nozzle
or accessory openings. DO NOT use
with any opening blocked; keep free
of dust, lint, hair, and anything that
may reduce airflow.
16. DO NOT use if nozzle or accessory
airflow is restricted. If the air paths or
the motorized floor nozzle become
blocked, turn the vacuum cleaner
off and unplug from electrical outlet.
Remove all obstructions before you
plug in and turn on the unit again.
17. Keep nozzle and all vacuum openings
away from hair, face, fingers,
uncovered feet, or loose clothing.
18. DO NOT use if vacuum cleaner is
not working as it should, or has been
dropped, damaged, left outdoors, or
dropped into water.
19. Use extra care when cleaning
on stairs.
20. DO NOT leave the vacuum cleaner
unattended while plugged in.
21. When powered on, keep the
vacuum cleaner moving over the
carpet surface at all times to avoid
damaging the carpet fibers.
22. DO NOT place vacuum cleaner
on unstable surfaces such as chairs
or tables.
23. Your Shark® vacuum may not
be designed to stand up on its own.
When taking a break from cleaning,
you may need to lean it against
furniture or a wall, or lay it flat
on the floor. Using the vacuum
for an application where the unit
lacks stability may result in
personal injury.
24. DO NOT use to pick up:
a) Liquids
b) Large objects
c) Hard or sharp objects
(glass, nails, screws, or coins)
d) Large quantities of dust (drywall
dust, fireplace ash, or embers).
DO NOT use as an attachment to
power tools for dust collection.
e) Smoking or burning objects
(hot coals, cigarette butts,
or matches)
f) Flammable or combustible
materials (lighter fluid, gasoline,
or kerosene)
g) Toxic materials (chlorine bleach,
ammonia, or drain cleaner)
25. DO NOT use in the following areas:
a) Poorly lit areas
b) Wet or damp surfaces
c) Outdoor areas
d) Spaces that are enclosed and may
contain explosive or toxic fumes
or vapors (lighter fluid, gasoline,
kerosene, paint, paint thinners,
mothproofing substances, or
flammable dust)
26. Turn off all controls before plugging
in or unplugging the vacuum.
27. Unplug from electrical outlet
when not in use and before
any maintenance or cleaning.
28. Hand wash with water only.
Washing with cleaning chemicals
could damage the unit.
29. During cleaning or routine
maintenance, DO NOT cut anything
other than hair, fibers, or string
wrapped around the brushroll.
30. Allow all filters to air-dry completely
before replacing in the vacuum to
prevent liquid from being drawn
into electric parts.
31. Make sure the dust cup and all
filters are in place after routine
maintenance.
32. If provided, secure the power
cord around the two cord hooks
during storage.
SAVE THESE INSTRUCTIONS

sharkclean.com
ASSEMBLY
1 2
3
4. For compact storage, hang the handheld
vacuum from the Storage Hook on the wand.
1. Insert Wand into Floor Nozzle.2. Insert Handheld Vacuum into wand.
3. Snap the Onboard Storage Clip onto the
wand, then place accessories in the holder.
Ensure all connections click securely into place.
(Snap)
(Click)
(Click)
4

sharkclean.com
SETTINGS
NOTE: Press the floor select button to toggle between Bare Floor and Carpet settings.
NOTE: For deep cleaning per ASTM F 608 (embedded dirt in carpets) please use the Carpet setting.
NOTE: Select Carpet for stuck-on dust and debris.
Power Button
Press the Power button to begin
vacuuming. Press again to turn o power.
Slide the floor select button to setting
II to clean carpets. In this setting, the
brushroll spins faster to pick up debris
below the surface ofyour carpets.
CONTROLS
The control panel is located on top of
the handheld vacuum.
POWER BUTTON
Slide the floor select button to setting
I to clean bare floors and small area
rugs. The brushroll spins slowly in
this setting.
BARE FLOOR SETTING CARPET SETTING

sharkclean.com
CLEANING MODES
NOTE: All accessories are compatible with both the wand and the handheld vacuum.
To clean floors, step on floor nozzle
and tilt handheld vacuum back.
To clean stairs or other narrow spaces,
attach the handheld vacuum to the
floor nozzle.
FLOOR MODE
STAIR CLEANING
For more reach, detach the wand. Stand
the vacuum upright, step on the Foot Pedal
on the side of the nozzle, and pull up the
wand to detach.
ABOVE-FLOOR WITH WAND
To detach the handheld vacuum, press
the Wand Release button and lift
the handheld vacuum o the wand.
Great for cleaning stairs, furniture, and
countertops.
ABOVE-FLOOR HANDHELD

sharkclean.com
STORAGE MODE
HANDHELD STORAGE HOOK
Press the Wand Release button near the top
of the wand to detach the handheld vacuum.
Align the Catch on the side of the handheld
vacuum with the Storage Hook on the wand,
then hang the handheld vacuum from the hook.
Wrap the cord around the two cord hooks.
Start with the top hook, and leave a little
slack in the cord.
Storage
Hook

sharkclean.com
AVAILABLE ACCESSORIES
ACrevice Tool
This slim tool is great for cleaning in tight
spaces, between couch cushions, and in
hard-to-reach areas. A longer crevice tool is
available at sharkaccessories.com.
BPet Crevice Tool
This versatile, slender 8" tool removes pet hair
from hard-to-reach spaces like corners, stairs,
and between couch cushions.
CUpholstery Tool
Picks up pet hair, dust, and large debris from
mattresses, couches, curtains, and other
delicate upholstered fabrics.
DDusting Brush
This brush dusts and cleans delicate surfaces.
Great for use on fans, blinds, lampshades,
and keyboards.
EPet Multi-Tool
A single convertible tool for cleaning tough pet
messes two ways: use the sti bristle brush to
clean stuck-on debris, or take o the bristles to
reveal an upholstery tool perfect for removing
stubborn pet hair and large piles of debris.
FDuster Crevice Tool
Two cleaning tools in one. The crevice tool
gives you extended reach to clean in tight
spaces, while the soft brush is ideal for dusting
delicate surfaces.
GAnti-Allergen Dust Brush
This brush features nylon fiber bristles specifically
designed for removing fine dust and allergen
particles from the most delicate surfaces.
HSelf-Cleaning Pet Power Brush
Tackles pet hair and ground-in dirt from above-
floor areas like carpeted stairs and upholstery,
while actively removing hair wrap as it cleans.
IPrecision Duster
This flexible tube features a micro-duster crevice
tool on the end for cleaning around delicate
objects and in dicult-to-reach spots like car
interiors and computer keyboards.
JUnder-Appliance Wand
Clean under and behind hard-to-move
appliances and furniture with this adjustable 36"
tool. Flip the extension piece over to clean the
underside of appliances.
KOnboard Storage Clip
This removable clip attaches to your vacuum.
The clip can store up to two accessories at a
time while you clean.
LAccessory Bag (Large, 32cm x 70 cm)
This convenient accessory storage bag
measures 32 cm x 70 cm and fits the Under-
Appliance Wand. Smaller size available at
sharkaccessories.com
NOTE: Not all accessories come with all units. For a list of the accessories included with this model, see the top
inside flap of the box. To order additional accessories, visit sharkaccessories.com.
B
A
D
F
J
H
C
E
G
I
K L

sharkclean.com
MAINTENANCE
EMPTYING THE DUST CUP
Press the Wand Release button and lift o
the handheld vacuum.
To remove the dust cup from the handheld
vacuum, press the two Dust Cup Release
buttons at the same time and slide out
the dust cup.
To reinstall, push the lid closed, then insert
the front end of the dust cup into the
handheld vacuum first, then the back end,
until it clicks into place.
Hold the dust cup over the trash. Press the
Empty button and pull open the dust cup lid
until it clicks and locks in the open position.
Gently tap the cone-shaped screen inside the
dust cup to knock dust and debris into the trash.
Empty the dust cup each time you vacuum and periodically during cleaning, when debris in the dust cup
reaches the MAX fill line.
IMPORTANT: Unplug the vacuum before performing any maintenance.
(Click)

sharkclean.com
Regularly rinse and replace the filters to maintain your vacuum's suction power.
To prevent damage from cleaning chemicals, rinse filters with cold water only. Do not use soap. Allow all filters to
air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn into electronic parts.
MAINTENANCE
CLEANING FILTERS
IMPORTANT: Unplug the vacuum before performing any maintenance.
PRE-MOTOR FILTERS POST-MOTOR FILTER
REPLACEMENT FILTERS
With the dust cup detached, press the Filter
Access buttons on both sides of the back of
the dust cup, then pull out the filter housing.
Pull the foam filter out of the housing, then
lift out the felt filter by the pull tab.
The Pre-Motor Filters should be washed
once a month.
To access the post-motor filter, press the
release latch on the filter cover on the
handheld vacuum. Remove the cover and
lift out the filter.
The Post-Motor Filter should be washed
once every 9 months.
NOTE: The pre-motor filters should be replaced every 2.5 years. The post-motor filter should be replaced every 3 years.
Replacement Pre-Motor Filter Kit
XFFKHZ2000
Replacement Post-Motor Filter
XPMFHZ2000

sharkclean.com
CHECKING FOR BLOCKAGES
MAINTENANCE
Remove the handheld vacuum from the
wand and check all dust cup intake openings
for debris or blockages.
Detach the wand and check it for blockages.
CHECK HANDHELD CHECK WAND
Detach the wand, then tilt the floor nozzle
Debris Intake back and check openings for
blockages.
CHECK FLOOR NOZZLE

sharkclean.com
MAINTENANCE
NOTE: For best performance, keep the Soft Roller clean with regular maintenance.
To minimize the risk of power cord damage, DO NOT run the vacuum over the power cord.
If this occurs, immediately shut o power to the vacuum and remove the cord from the
brushroll or nozzle.
1. DO NOT pull or carry vacuum cleaner by
the cord or use cord as a handle.
2. DO NOT unplug by pulling on the cord.
Grasp the plug, not the cord.
3. DO NOT close the door on the cord.
4. DO NOT pull the cord around sharp
corners.
5. DO NOT leave the cord near heated
surfaces.
CORD MAINTENANCE
Clean o any debris on the brushroll. Check the Debris intake and clear away any dirt
or blockages. To close the cover, push down
until it clicks into place.
NOZZLE MAINTENANCE
DEBRIS WRAPPED
AROUND BRUSHROLL
SELF-CLEANING BRUSHROLL
If you run over a hard or sharp object or notice a noise change while vacuuming, check for
blockages or objects caught in the brushroll.
If some fibers remain wrapped around the brushroll after continued use, clear them from the
brushroll.
DEBRIS BEHIND BRUSHROLL

sharkclean.com
TROUBLESHOOTING
For all other issues, visit sharkclean.com/support.
Power cord caught in brushroll or floor nozzle.
• To minimize the risk of power cord damage, DO NOT run the vacuum over the power cord. If this
occurs, immediately shut o power to the vacuum and remove the cord from the brushroll or nozzle.
• Inspect power cord and plug for any damage before use. DO NOT use vacuum cleaner with a
damaged cord or plug. Turn o all controls before plugging in or unplugging the vacuum cleaner.
Store your vacuum cleaner with the power cord secured around the two cord hooks.
Vacuum is not picking up debris. No suction or light suction.
See Maintenance section for more information.
• Empty the dust cup. Check filters to see if they need cleaning. Follow instructions for rinsing and
completely air-drying the filters before reinstalling them.
• Clear any blockages in the nozzle, wand, handheld vacuum, or accessories. See Checking for Blockages
section for more information.
• If any string, hair, or carpet fibers remain wrapped around the brushroll after continued use, carefully
clear them away.
• Remove any blockages from the debris intake in the floor nozzle. Pinch the tabs on the bottom of the
nozzle to open the cover, and lift up the intake tube. Clear blockages, then push the tube down and
press the nozzle cover closed.
Vacuum lifts area rugs.
• Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges.
• Turn o the unit to disengage the brushroll. To restart, press the power button on the handle.
NOTE: Clean area rugs in Bare Floor mode or with accessories. See Available Accessories section.
Vacuum turns o on its own or the indicator light flashes red.
If your vacuum overheats, the thermostat will automatically turn o the motor. Perform the following steps
to restart:
1. Turn o the vacuum and unplug it.
2. Empty the dust cup and clean the filters. See Emptying the Dust Cup and Cleaning Filters sections.
3. Check for blockages in the wand, floor nozzle, handheld vacuum, inlet openings, and accessories.
4. Reassemble the entire vacuum and ensure all parts click into place.
5. Allow unit to cool for a minimum of 60 minutes.
6. Plug in vacuum and turn it on.
Handheld vacuum is warm.
Due to the strong suction power of the vacuum, it is normal for the area around the filter exhaust to
become warm during and after use. Turn o the vacuum and wait 10 minutes for it to cool down. If it
still feels warm, clean the pre-motor and post-motor filters. See Maintenance section for filter cleaning
instructions.

sharkclean.com
The Five (5) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja
Operating LLC. Warranty coverage applies to the original owner and to the original product only and is
not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period
of five (5) years from the date of purchase when it is used under normal household conditions and
maintained according to the requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
1. The original unit and/or non-wearable components deemed defective, in SharkNinja’s sole discretion,
will be repaired or replaced up to five (5) years from the original purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the
receipt date of the replacement unit or the remainder of the existing warranty, whichever is later.
SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
1. Normal wear and tear of wearable parts (such as foam filters, HEPA filters, pads, etc.), which require
regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered
by this warranty. Replacement parts are available for purchase at sharkaccessories.com.
2. Any unit that has been tampered with or used for commercial purposes.
3. Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling,
failure to perform required maintenance (e.g., not cleaning the filters), or damage due to mishandling
in transit.
4. Consequential and incidental damages.
5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused
in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the
repair is performed by a repair person not authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal household conditions within the warranty
period, visit sharkclean.com/support for product care and maintenance self-help. Our Customer Service
Specialists are also available at 1-800-798-7398 to assist with product support and warranty service options,
including the possibility of upgrading to our VIP warranty service options for select product categories.
SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of
$25.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-800-798-7398 to initiate a warranty claim. You will need the receipt as proof of purchase.
A Customer Service Specialist will provide you with return and packing instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other rights that vary from state to
state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so
the above may not apply to you.
FIVE (5) YEAR LIMITED WARRANTY

sharkclean.com
TECHNICAL SPECIFICATIONS
Voltage: 120V~, 60Hz
Watts: 680W
RECORD THIS INFORMATION
Model Number: ������������������������
Date Code: ����������������������������
Date of Purchase: ����������������������
(Keep receipt)
Store of Purchase: ����������������������
REGISTER YOUR PURCHASE
registeryourshark.com
Scan QR code using
mobile device
TIP: The model number is on the rating label
behind the dust cup.
TIP: The date code is on one of the prongs
of the power cordplug.
Benefits of registering your product and
creating an account:
• Get easier, faster product support and
access to warranty information
• Access troubleshooting and product care
instructions
• Be among the first to know about
exclusive product promotions

© 2021 SharkNinja Operating LLC. SHARK is a registered trademark of SharkNinja Operating LLC.
POWERFINS is a trademark of SharkNinja Operating LLC.
HZ600Series�IB�E�MP�210416
PRINTED IN CHINA
PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
This Owner’s Guide is designed to help you get a complete understanding of your new Shark
Ultralight PowerFins™ Corded Stick Vacuum with Self-Cleaning Brushroll.
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7
sharkclean.com
Illustrations may dier from actual product. We are constantly striving to improve our products;
therefore the specifications contained herein are subject to change without notice.
For SharkNinja U.S. Patent information, visit sharkninja.com/uspatents

UltraLight PowerFins™
Corded Stick Vacuum with
Self-Cleaning Brushroll
Aspirateur-balai à fil ultraléger
PowerFins™avec brosse
rotative autonettoyante
Aspiradora vertical de varilla
con cable UltraLight PowerFins™
con cepillo giratorio de
autolimpieza
HZ600 Series • Série • Serie
OWNER’S GUIDE
GUIDE DE L’UTILISATEUR
GUÍA DEL PROPIETARIO

sharkclean.com
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM
1. Inspect power cord and plug for any
damage before use. DO NOT use
vacuum cleaner with a damaged
cord or plug. Turn off all controls
before plugging in or unplugging
the vacuum cleaner. Store your
vacuum cleaner with the power cord
secured around the two cord hooks.
To minimize the risk of power cord
damage, do not allow the motorized
brush roll to ingest the cord. If this
occurs, immediately shut off power
to the vacuum and remove the cord.
2. This appliance has a polarized plug,
if the plug does not fit fully into the
outlet, reverse the plug (one blade is
wider than the other). If it still does
not fit, contact a qualified electrician.
DO NOT force into outlet or try to
modify to fit.
3. Your vacuum cleaner may consist of
a motorized nozzle, wand, hose, and/
or vacuum pod. This device contains
electrical connections, electrical
wiring, and moving parts that
potentially present risk to the user.
4. Use only identical replacement parts.
5. Carefully observe and follow the
instructions provided below to avoid
improper use of the appliance.
DO NOT use the vacuum for any
purpose other than those described
in this manual.
6. Before use, carefully inspect all parts
for any damage. DO NOT use if any
parts are damaged.
7. The use of an extension cord is
NOT recommended.
8. This vacuum cleaner contains
no serviceable parts.
9. This appliance can be used by
persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Cleaning and user maintenance
shall not be made by children. Keep
the appliance and its cord out of
reach of children. DO NOT allow the
appliance to be used by children. DO
NOT allow to be used as a toy. Close
supervision is necessary when used
near children.
10. Always turn off the vacuum cleaner
before connecting or disconnecting
any motorized nozzles or other
accessories.
11. DO NOT handle plug or vacuum
cleaner with wet hands.
12. DO NOT use without filters in place.
13. Only use Shark® branded filters
and accessories.
14. DO NOT damage the power cord:
a) DO NOT pull or carry vacuum
cleaner by the cord or use the
cord as a handle.
b) DO NOT unplug by pulling on
cord. Grasp the plug, not the cord.
c) DO NOT run the vacuum cleaner
over the power cord, close a door
on the cord, pull the cord around
sharp corners, or leave the cord
near heated surfaces.
WARNING
To reduce the risk of fire, electric shock, injury, or property damage, when using
an electrical appliance, basic precautions should always be followed, including
the following:
IMPORTANT SAFETY INSTRUCTIONS
FOR HOUSEHOLD USE ONLY

sharkclean.com
15. DO NOT put any objects into nozzle
or accessory openings. DO NOT use
with any opening blocked; keep free
of dust, lint, hair, and anything that
may reduce airflow.
16. DO NOT use if nozzle or accessory
airflow is restricted. If the air paths or
the motorized floor nozzle become
blocked, turn the vacuum cleaner
off and unplug from electrical outlet.
Remove all obstructions before you
plug in and turn on the unit again.
17. Keep nozzle and all vacuum openings
away from hair, face, fingers,
uncovered feet, or loose clothing.
18. DO NOT use if vacuum cleaner is
not working as it should, or has been
dropped, damaged, left outdoors, or
dropped into water.
19. Use extra care when cleaning
on stairs.
20. DO NOT leave the vacuum cleaner
unattended while plugged in.
21. When powered on, keep the
vacuum cleaner moving over the
carpet surface at all times to avoid
damaging the carpet fibers.
22. DO NOT place vacuum cleaner
on unstable surfaces such as chairs
or tables.
23. Your Shark® vacuum may not
be designed to stand up on its own.
When taking a break from cleaning,
you may need to lean it against
furniture or a wall, or lay it flat
on the floor. Using the vacuum
for an application where the unit
lacks stability may result in
personal injury.
24. DO NOT use to pick up:
a) Liquids
b) Large objects
c) Hard or sharp objects
(glass, nails, screws, or coins)
d) Large quantities of dust (drywall
dust, fireplace ash, or embers).
DO NOT use as an attachment to
power tools for dust collection.
e) Smoking or burning objects
(hot coals, cigarette butts,
or matches)
f) Flammable or combustible
materials (lighter fluid, gasoline,
or kerosene)
g) Toxic materials (chlorine bleach,
ammonia, or drain cleaner)
25. DO NOT use in the following areas:
a) Poorly lit areas
b) Wet or damp surfaces
c) Outdoor areas
d) Spaces that are enclosed and may
contain explosive or toxic fumes
or vapors (lighter fluid, gasoline,
kerosene, paint, paint thinners,
mothproofing substances, or
flammable dust)
26. Turn off all controls before plugging
in or unplugging the vacuum.
27. Unplug from electrical outlet
when not in use and before
any maintenance or cleaning.
28. Hand wash with water only.
Washing with cleaning chemicals
could damage the unit.
29. During cleaning or routine
maintenance, DO NOT cut anything
other than hair, fibers, or string
wrapped around the brushroll.
30. Allow all filters to air-dry completely
before replacing in the vacuum to
prevent liquid from being drawn
into electric parts.
31. Make sure the dust cup and all
filters are in place after routine
maintenance.
32. If provided, secure the power
cord around the two cord hooks
during storage.
SAVE THESE INSTRUCTIONS

sharkclean.com
ASSEMBLY
4. For compact storage, hang the handheld
vacuum from the Storage Hook on the wand.
1. Insert Wand into Floor Nozzle.2. Insert Handheld Vacuum into wand.
3. Snap the Onboard Storage Clip onto the
wand, then place accessories in the holder.
Ensure all connections click securely into place.
(Snap)
(Click)
(Click)