Sharp EL-1611E User manual

OPERATION MANUAL
MANUAL DE MANEJO
HASZNÁLATI ÚTMUTATÓ
EL-1611E
ELECTRONIC PRINTING CALCULATOR
CALCULADORA IMPRESORA ELECTRÓNICA
SZALAGOS ASZTALI KALKULÁTOR
ENGLISH .................................................................... Page 1
CALCULATION EXAMPLES ...................................... Page 34
ESPAÑOL ................................................................... Página 12
EJEMPLOS DE CÁLCULOS ...................................... Página 34
MAGYAR .................................................................... Oldal 23
PÉLDASZÁMÍTÁSOK ................................................ Oldal 35

1
Page
OPERATING CONTROLS ......................................................... 2
INK ROLLER REPLACEMENT ................................................. 3
PAPER ROLL REPLACEMENT ................................................ 5
POWER SUPPLY ...................................................................... 7
ERRORS ................................................................................... 9
SPECIFICATIONS ..................................................................... 10
RESETTING THE UNIT ............................................................ 11
CALCULATION EXAMPLES ..................................................... 34
EURO CURRENCY RATES ...................................................... 40
Thank you for your purchase of the SHARP electronic printing
calculator, model EL-1611E.
To insure trouble-free operation of your SHARP calculator, we
recommend the following:
1. The calculator should be kept in areas free from extreme
temperature changes, moisture, and dust.
2. A soft, dry cloth should be used to clean the calculator. Do not
use solvents or a wet cloth.
3. Since this product is not waterproof, do not use it or store it
where fluids, for example water, can splash onto it. Raindrops,
water spray, juice, coffee, steam, perspiration, etc. will also
cause malfunction.
4. If service should be required, use only a SHARP servicing
dealer, a SHARP approved service facility or SHARP repair
service.
5. If you pull out the power cord to cut electricity completely or
replace the batteries, the presently stored tax rate will be
cleared.
6. This product, including accessories, may change due to
upgrading without prior notice.
ENGLISH
OPERATIONAL NOTES CONTENTS

2
OPERATING CONTROLS

POWER ON KEY / CLEAR / CLEAR ENTRY KEY:
Clear – This key also serves as a clear key for the calculation
register and resets an error condition.
Clear entry – When pressed after a number and before a
function, clear the number.
POWER OFF KEY:
When this key is pressed, the power is turned off.
PRINT KEY:
To save paper you can only print what is displayed, even in
non-print mode.
Pressing after the entry of a number will print the entry
with the symbol “#” even in non-print mode.
Pressing will insert a separator into a number entry such
as a code, date, etc. Separators are displayed as a period
and dashes but printed as periods.
MEMORY + KEY / PRINT ON / OFF KEY:
Pressing selects print mode or non-print mode.
Cause the calculator to operate in a display / print or display
only mode, depending upon the calculator’s present state.
“P” on the display: Print mode.
“NP” on the display: Non-print mode.
MEMORY – KEY / DECIMAL SELECTION KEY:
Pressing sets the number of decimal places in the
result.
“F” on the display:
The answer is displayed in the floating decimal system.
“3, 2, 1, 0” on the display:
Presets the number of decimal places in the answer.
“A” on the display (Add mode):
The decimal point in addition and subtraction entries is
automatically positioned to the 2nd digit from the lowest
digit of entry number. Use of the add mode permits
addition and subtraction of numbers without entry of the
decimal point. Use of , and will automatically
override the add mode and decimally correct answers will
be printed.
CONVERSION KEY (TO THE EURO CURRENCY) :

3
CONVERSION KEY (TO A NATIONAL CURRENCY) /
CONVERSION RATE SETTING KEY:
You can set the exchange rate by pressing . (A
maximum of 6 digits excluding the decimal point can be
stored as the exchange rate.)
2nd FUNCTION KEY:
To use the functions shown above the keys, such as “DEC”,
press the key first. (When the key is pressed,
“2nd” will appear at the top of the display.)
Example: To change decimal place setting from F to 2
,
PAPER FEED KEY:
When pressed, the paper tape advances.
DISPLAY:
F: Floating decimal mode :Euro Currency Symbol
3, 2, 1, 0: Preset decimal mode :
National Currency Symbol
A: Add mode M: Memory
P: Print mode –: Minus
NP: Non-print mode E: Error
2nd: functions are available
•For illustration purposes, all the relevant symbols are visible in
the display above. However, in actual use, this would never
happen.
If printing is blurry even when the ink roller is in the proper position,
replace the roller.
Ink roller: Type EA-772R
WARNING
APPLYING INK TO WORN INK ROLLER OR USE OF
UNAPPROVED INK ROLLER MAY CAUSE SERIOUS
DAMAGE TO PRINTER.
1) Turn the power off.
2) Remove the printer cover. (Fig. 1)
3) Hold the top of the ink roller and remove the roller by pulling it
toward you and then upward. (Fig. 2)
INK ROLLER REPLACEMENT

4
Fig. 1 Fig. 2 Fig. 3
Cleaning the printing mechanism
If the print becomes dull after long time usage, clean the
printing wheel according to the following procedures:
1) Remove the printer cover and the ink roller.
2) Install the paper roll and feed it until it comes out of the front of
the printing mechanism.
3) Put a small brush (like a tooth brush) lightly to the printing
wheel and clean it by pressing .
4) Put back the ink roller and the printer cover.
Note: •Do not rotate the printing mechanism manually, this may
damage the printer.
4) Install the new ink roller in the correct position. Make sure that
the roller is securely in place. (Fig. 3)
5) Put back the printer cover.

5
PAPER ROLL REPLACEMENT
Never insert paper roll if torn. Doing so will cause paper to jam. Always cut leading edge with scissors first.
♦When using the paper that is less than or equals to 25 mm (31/32") in outside diameter:
Paper roll : Type EA-7100P
STEP 1 STEP 2 STEP 3
STEP 4
leading edge
Paper
cutter
Note: Paper tape replacement rolls are available where the EL-1611E calculator is sold.

6
♦When using the paper that is 12mm (15/32") in inside diameter and up to 80mm (3-5/32") in outside diameter:
Caution: •Never use the supplied paper (25 mm (31/32") in outside
diameter) in the holder.
•When replacing the paper, touching the inside of the
printer may damage it.
•The calculator has a free-paper mechanism. When
drawing out the paper tape, pull it straight forward on the
paper cutter side.
STEP 1 STEP 2 STEP 3 STEP 4
Paper holder
STEP 5 STEP 6

7
5. After the replacement, press and in this order to clear
the calculator.
When the batteries are correctly installed “0.” will be displayed.
(If the display is blank, displays any other symbol or the keys
become inoperative, remove the batteries and install them
again. Press and in this order and check the display
again.)
Note: Due to solvent leakage of the battery, keeping a used
battery in the battery compartment may result in damage to
the calculator. Remove a used battery promptly.
This calculator operates on dry batteries.
The calculator can also be operated on AC power through use of
an AC adaptor.
BATTERY OPERATION
If the display becomes dim or the printer stops before or during
printing, the batteries should be replaced.
Battery: Heavy-duty manganese battery AA (or R6) ×4
1. Turn off power by pressing .
2. Remove the battery cover by sliding it in the direction of the
arrow on the cover.
3. Replace the batteries. Be sure that the “+” and “–” marks on the
battery correspond to the “+” and “–” marks in the calculator.
Always put back the 4 batteries at the same time.
4. Put back the battery cover.
POWER SUPPLY
Battery cover

8
AC POWER OPERATION (OPTION)
AC adaptor: Model EA-28A
When the AC adaptor is connected to the calculator, the power
source is automatically switched over from dry batteries to AC
power source.
HOW TO CONNECT THE AC ADAPTOR
Make sure that you turn the calculator’s power off when connecting
or disconnecting the AC adaptor.
To connect the AC adaptor, follow steps ➀and ➁.
To disconnect the AC adaptor, simply reverse the procedure.
Notes: •When the calculator is not in use, be sure to remove the
adaptor from the calculator and the wall outlet.
•Never use any other AC adaptor except EA-28A.
CAUTION
Use of other than the AC adaptor EA-28A may apply improper
voltage to your SHARP calculator and will cause damage.
AC adaptor
connecting
terminal
This optional AC adaptor is not available in some regions.
Please ask your Sharp dealer for details.