Sharp LC-20S4U-S - 20" LCD TV Operating manual

LC-20S4U-S
SUPPLEMENT
SERVICE MANUAL
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
MODEL LC-20S4U-S
SHARP CORPORATION This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
LCD COLOR TELEVISION
CONTENTS
»IMPORTANT SERVICE SAFETY PRECAUTION .........................................................................................2
»REMOVING OF MAJOR PARTS ..................................................................................................................5
»OVERALL WIRING DIAGRAM .....................................................................................................................8
»SCHEMATIC DIAGRAM
ËMAIN Unit.................................................................................................................................................10
ËANALOG Unit...........................................................................................................................................22
»REPLACEMENT PARTS LIST....................................................................................................................30
»PACKING OF THE SET ..............................................................................................................................39
Page
The LCD panel of this model has been redesigned. With this redesign, the main and analog PWB unit as well
as the LCD panel-related and other mechanical parts have also been modified and these parts are not
interchangeable with those of previous LCD panel models in servicing.
This Supplement covers the modified points from the previous Supplement.
For other technical points, refer to the Service Manual for previous LCD panel model LC-20S4U-S
(S2F1LC20S4US) as well as the Supplement for LC-20S4U-S (S65K1LC20S4US).
The previous LCD panel models and the new model can be identified with the following markings.
•The Bcharacter is added at the end of the model name on the model label.
•The Bcharacter is also added at the end of the model name on the number label (barcode label) of the
packing case.
•The serial product numbers (in the 5th thru 9th digits) are 81112 and on.
OUTLINE
SUPPLEMENT
S05P1LC20S4US

2
LC-20S4U-S
SUPPLEMENT
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012
1
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
1
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
2
1
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
2
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
SAFETY NOTICE
Many electrical and mechanical parts in LCD television
have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by " å"
IMPORTANT SERVICE SAFETY PRECAUTION
ËService work should be performed only by qualified service technicians who are thor-
oughly familiar with all safety checks and the servicing guidelines which follow:
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams .
For continued protection, replacement parts must be
identical to those used in the original circuit.
The use of substitute replacement parts which do not
have the same safety characteristics as the factory
recommended replacement parts shown in this service
manual, may create shock, fire or other hazards.
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks:
1. Inspect all lead dress to make certain that leads are
not pinched, and check that hardware is not lodged
between the chassis and other metal parts in the
receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulation materials, cabinet backs,
adjustment and compartment covers or shields, isolation
resistor-capacitor networks, mechanical insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
•Plug the AC cord directly into a 110~240 volt AC outlet,
and connect the DC power cable into the receiver's DC
jack. (Do not use an isolation transformer for this test).
•Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as electrical conduit or electrical ground
connected to an earth ground.
•Use an AC voltmeter having with 5000 ohm per volt, or
higher, sensitivity or measure the AC voltage drop
across the resistor.
•Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
All checks must be repeated with the AC cord plug
connection reversed. (If necessary, a nonpolarized
adaptor plug must be used only for the purpose of
completing these checks.)
Any reading of 0.75V peak (this corresponds to 0.5 mA.
peak AC.) or more is excessive and indicates a potential
shock hazard which must be corrected before returning
the monitor to the owner.
DVM
AC SCALE
1.5k ohm
10W
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
0.15 µF
TEST PROBE
CAUTION: FOR CONTINUED
PROTECTION AGAINST A RISK OF
FIRE REPLACE ONLY WITH SAME
TYPE F3701 (2.5A, 250V) AND
F3702 (2.0A, 250V) FUSE.
A V

3
LC-20S4U-S
SUPPLEMENT
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
1
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
2
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
1
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
2
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans
les téléviseurs de l ' afficharge à cristaux liquides
présentent des caractéristiques spéciales relatives à la
sécurité.
Ces caracténstiques ne sont souvent pas évidentes à vue.
Le degré de protection ne peut pas être nécessairement
augmentée en utilisant des pièces de remplacement
étalonnées pour haute tension, puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel; les
pièces électriques qui présentent ces particularités sont
identifiées par la marque " å" et hachurées dans la liste
des pièces de remplacement et les diagrammes
schématiques .
Pour assurer la protection, ces pièces doivent être
identiques à celles utilisées dans le circuit d'origine.
L'utilisation de pièces qui n'ont pas les mêmes
caractéristiques que les pièces recommandées par
l'usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies ou autres accidents.
DVM
ECHELLE CA
1.5k ohm
10W
0.15 µF
SONDE D'ESSAI
AUX PIECES
METALLIQUES
EXPOSEES
BRANCHER A UNE
TERRE CONNUE
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
ËLa réparation ne peut être effectuée que par un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
1. Pour la sécuritécontinue, n'entreprendre aucune
modification de tout circuit.
2. Débrancher l'alimentation CA avant la réparation.
AVANT DE RENDRE LE RECEPTEUR A
L’UTILISATEUR (Incendie et choc électrique)
Avant de rendre le récepteur à l'utilisateur, effectuer
les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer
que les fils ne soient pas pincés ou qu'un outil ne soit
pas placéentre le châssis et les autres pièces
métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme les
boutons de commande non-métalliques, les isolants,
le dos du coffret, les couvercles ou blindages de réglage
et de compartiment, les réseaux de résistance-capacité,
les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution en
vérifiant la fuite de courant, de la facon suivante:
•Enficher le cordon d’alimentation directement dans une
prise de 110-240V CA, et brancher le câble
d’alimentation CC àla prise CC du récepteur. (Ne pas
utiliser de transformateur d’isolation pour cet essai.)
•A l'aide de deux fils àpinces, brancher une résistance
de 1.5kΩ10 watts en parallèle avec un condensateur
de 0.15µF en série avec toutes les pièces métalliques
exposées du coffret et une terre connue comme une
conduite électrique ou une prise de terre branchée àla
terre.
•Utiliser un voltmètre CA d'une sensibilitéd'au moins
5000Ω/V pour mesurer la chute de tension CA en
travers de la résistance.
•Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au châssis
(antenne, coffret métallique, tête des vis, arbres de
commande et des boutons, écusson, etc.) et mesurer
la chute de tension CA en travers de la résistance.
Toutes les vérifications doivent être refaites après avoir
inverséla fiche du cordon d'alimentation. (Si nécessaire,
une prise d'adpatation non polarisée doit être utilisée
dans le but de terminer ces vérifications.)
La tension de pointe mesurèe ne doit pas dépasser
0.75V (correspondante au courant CA de pointe de
0.5mA). Dans le cas contraire, il y a une possibilitéde
choc électrique qui doit être supprimée avant de rendre
le récepteur au client.
PRECAUTION: POUR LA
PROTECTION CONTINUE
CONTRE LES RISQUES
D'INCENDIE, REMPLACER LE
FUSIBLE PAR UN FUSIBLE DE
MEME TYPE F3701 (2.5A, 250V)
ET F3702 (2.0A, 250V).
A V

4
LC-20S4U-S
SUPPLEMENT
Precautions for using lead-free solder
1 Employing lead-free solder
"All PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on
the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
Example:
2 Using lead-free wire solder
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional
lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend
you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit,
contact our service station or service branch in your area.
3 Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead
solder by 40°C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the
PWB for extended period of time. However, Since the land may be peeled off or the maximum heat-resistance
temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady soldering
condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on
and off the power of the bit as required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after
every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Indicates lead-free solder of tin, silver and copper.
Lead-free wire solder for servicing
Part No. ★Description Code
ZHNDAi123250E J φ0.3mm 250g(1roll) BL
ZHNDAi126500E J φ0.6mm 500g(1roll) BK
ZHNDAi12801KE J φ1.0mm 1kg(1roll) BM
LFa

5
LC-20S4U-S
SUPPLEMENT
REMOVING OF MAJOR PARTS
1. Remove the stand cover fixing screws (1 pc.)
2. Remove the stand fixing screws (4 pcs.).
3. Remove the carrying handle fixing screws (4 pcs.).
4. Remove the terminal covers (left and right).
5. Remove the terminal screws (6 pcs.).
6. Remove the cabinet B fixing screws (8 pcs.).
7. Remove the cabinet B after opening from the direction of an arrow.
8. Remove the stand angle fixing screws (3 pcs.).
9. Disconnect all the connectors from all the PWBs.
3
6
4
4
5
5
5
5
7
1
2
Cabinet B
Carrying Handle
Cabinet A
Terminal Cover (R)
Terminal Cover (L)
Stand
Stand Cover
P6706
P6705
P6704
P6703
P6702
SC3401 P3701
P3702
P3402 P3401
CN1
SC4051 SC6701
SC2001 SC4052
SC701
P4001
8
9
9
9
9
9
9
9
9
9
9
SC1201
Operation PWB
Stand Angle
Main PWB
R/C, LED PWB Inverter PWB
Analog PWB

6
LC-20S4U-S
SUPPLEMENT
10. Remove the 3 lock screws from the main PWB, and undo the claws a and b. Detach the main PWB by lifting the
area around the claws and pulling the PWB out.
11. Remove the 3 lock screws from the analog PWB, and undo the claws c and d. Detach the chassis frame (right)
from the analog PWB by pulling out the terminals. In the same way, undo the claws e and f, and detach the
chassis frame (left) from the analog PWB by pulling out the terminals.
Note: When detaching the main PWB and analog PWB, be careful not to break the PWB-fixing claws.
12. Remove the operation PWB fixing screws (5 pcs.)
13. Remove the inverter PWB fixing screws (2 pcs.)
14. Remove the R/C, LED PWB fixing screws (2 pcs.)
15. Remove the 3 lock screws each from the right and left speakers and take out both the speakers.
10
10
11
12
13
15
14
15
a
b
c
d
f
e
e
Inverter PWB
Main PWB
Analog PWB
Operation PWB
Chassis Frame (L)
Chassis Frame (R)
Speaker (R)
R/C, LED PWB
Speaker (L)

7
LC-20S4U-S
SUPPLEMENT
»Precautions in handling the LCD panels
1. Work in a clean room (with humidities below 50%).
2. Be sure to wear an anti-static armband.
3. Handle the panels on an electro-conductive mat.
4. Be careful not to fall, shake and shock the panels.
16. Detach the back shield.
17. Remove the 5 lock screws from the bezel and detach the bezel.
Note: Carefully undo the hooks in the four directions.
18. Detach the LCD panel from the backlight case.
Note1: Carefully undo the hooks in the four directions.
Note2: Do not remove the LCD panel from the panel chassis. Be careful not to touch the LCD panel's glass faces,
driver IC, PWBs and other components with bare hands. (Otherwise defects may be caused in the production
line.)
19. Remove the diffusion sheets (top), lens sheet, diffusion sheet (bottom) and diffusion plate.
Note: Fit the diffusion plate and sheets tightly in the backlight casing.
If set out of position, the panel may get cracked.
20. Detach the lamp unit from the backlight case.
Diffusion Plate
(PSLDK2553TPZZ)
Diffusion Sheet (Bottom)
(PSLDK2554TPZZ)
Diffusion Sheet (Top), x2
(PSLDK2567TPZZ)
Lens Sheet
(POFMA0220TPZZ)
Back shield
(PSLDMA810WJN1)
16
Back light Case
(LHLDZ3104TPZA)
Lamp Unit, x5
(RLMPC2401TPZZ)
17
20
19
18
17
17
Bezel
(LANGK3261TPZA)
20" LCD Panel

98
LC-20S4U-S
SUPPLEMENT
121110987654321
A
B
C
D
E
F
G
H
OVERALL WIRING DIAGRAM

1110
LC-20S4U-S
SUPPLEMENT
121110987654321
A
B
C
D
E
F
G
H
SCHEMATIC DIAGRAM
ËMAIN Unit-1/6

1312
LC-20S4U-S
SUPPLEMENT
121110987654321
A
B
C
D
E
F
G
H
ËMAIN Unit-2/6

1514
LC-20S4U-S
SUPPLEMENT
121110987654321
A
B
C
D
E
F
G
H
ËMAIN Unit-3/6

1716
LC-20S4U-S
SUPPLEMENT
121110987654321
A
B
C
D
E
F
G
H
ËMAIN Unit-4/6

1918
LC-20S4U-S
SUPPLEMENT
121110987654321
A
B
C
D
E
F
G
H
ËMAIN Unit-5/6

2120
LC-20S4U-S
SUPPLEMENT
121110987654321
A
B
C
D
E
F
G
H
ËMAIN Unit-6/6

2322
LC-20S4U-S
SUPPLEMENT
121110987654321
A
B
C
D
E
F
G
H
ËANALOG Unit-1/4

2524
LC-20S4U-S
SUPPLEMENT
121110987654321
A
B
C
D
E
F
G
H
ËANALOG Unit-2/4

2726
LC-20S4U-S
SUPPLEMENT
121110987654321
A
B
C
D
E
F
G
H
ËANALOG Unit-3/4

2928
LC-20S4U-S
SUPPLEMENT
121110987654321
A
B
C
D
E
F
G
H
ËANALOG Unit-4/4

Ref. No. Part No. ★Description Code Ref. No. Part No. ★Description Code
30
LC-20S4U-S
SUPPLEMENT
★ MARK: SPARE PARTS-DELIVERY SECTION ★ MARQUE: SECTION LIVRAISON DES PIECES DERECHANGE
PARTS LIST
PARTS REPLACEMENT
Replacement parts which have these special safety characteristics iden-
tified in this manual ; electrical components having such features are
identified by åand shaded areas in the Replacement Parts Lists and
Schematic Diagrams. The use of a substitute replacement part which
does no have the same safety characteristic as the factory recommended
replacement parts shown in this service manual may create shock, fire
or other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the fol-
lowing informations.
1. MODEL NUMBER 2. REF. NO.
3. PART NO. 4. DESCRIPTION
in USA: Contact your nearest SHARP Parts Distributor to order. For
location of SHARP Parts Distributor, Please call Toll-Free;
1-800-BE-SHARP
LISTE DES PIECES
CHANGE DES PIECES
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques sp
éleciales de s élecurit éle, sont identifi élees dans ce manuel : les pi`eces
élelectriques qui pr élesentent ces particularit éles, sont rep éler élee
par la marque ået sont hachur élees dans les listes de pi`eces et dans
les diagrammes sch élematiques.
La substitution d'une pi`ece de rechange par une autre qui ne pr éLesente
pas les m éoemes caract éLeristiques de s élecurit éle que la pi`ece
recommand élee parl'usine et dans ce manuel de service, peut provoquer
une éLelectrocution, un incendie ou toutautre sinistre.
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit rapidement et correctement remplie,
veuillez fournir les renseignements suivants.
1. NUMERO DU MODELE 2. NO. DE REF
3. NO. DE PIECE 4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Canada Limited
Phone [phone]
Ref. No. Part No. ★Description Code Ref. No. Part No. ★Description Code
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
DUNTKD234FE21 – MAIN Unit —
DUNTKD084WE06 – ANALOG Unit —
Note: The R/C, LED unit, inverter unit have only their part
numbers changed. There is no change in the Schematic
Diagram, Printed Wiring Board Assemblies and Parts List.
DUNTKD085WE06 – R/C,LED Unit —
RUNTKA124WJN1 – INVERTER Unit —
LCD PANEL
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDENTLY.
RLCUCA022WJZZ J 20" LCD Panel Unit Ass'y CT
DUNTKD234FE21
MAIN Unit
INTEGRATED CIRCUITS
C701 RH-iXA828WJZZY J BD9300FV-FE2 AH
IC702 RH-iXA828WJZZY J BD9300FV-FE2 AH
IC703 RH-iXA828WJZZY J BD9300FV-FE2 AH
IC705 RH-iXA828WJZZY J BD9300FV-FE2 AH
IC801 RH-iXB150WJZZQ J R8A66605A02FP BG
IC802 VHiPQ018EH1-1Y J PQ018EH01ZPH AF
IC1101 VHiBD8133FV-1Y J BD8133FV-E2 AS
IC1201 RH-iXB075WJZZQ J LR38875 AX
IC1202 VHiFSA4157+-1Y J FSA4157P6X AE
IC1703 VHiNJM2147M-1Y J NJM2147M-TE1 AF
IC2001 RH-iXA630WJZZQ J M30622MWP-245F AV
IC2003 VHiSi3010KM-1Y J SI-3010KM-TL AF
IC2006 VHiPST3229N1EY J PST3229 AD
IC2009 VHiBR24L32F-1Y J BR24L32F-WE2 AG
IC2010 VHiPST3229N1EY J PST3229 AD
IC2011 VHiPQ1L333M-1Y J PQ1L333M2SP AD
TRANSISTORS
Q705 VSUML2N++++-1Y J UML2N AC
Q706 VSUML2N++++-1Y J UML2N AC
Q708 VSUML2N++++-1Y J UML2N AC
Q709 VSUML1N++++-1Y J UML1N AC
Q710 VSUML1N++++-1Y J UML1N AC
Q711 VSUML2N++++-1Y J UML2N AC
Q712 VSRTQ035P02-1Y J RTQ035P02 AD
Q713 VSRTQ035P02-1Y J RTQ035P02 AD
Q715 VSRHP020N06-1Y J RHP020N06 AD
Q716 VSRHP020N06-1Y J RHP020N06 AD
Q802 VSFMMT718//-1Y J FMMT718 AE
Q803 VS2SC3928AR-1Y J 2SC3928AR AB
Q1107 VS2SA1037KQ-1Y J 2SA1037KQ AA
Q1108 VSDTC114EE/-1Y J DTC114EE AB
Q1701 VS2SA1037KQ-1Y J 2SA1037KQ AA
Q1702 VSDTC144EE/-1Y J DTC144EE AA
Q1703 VS2SA1036K/-1Y J 2SA1036K AC
Q1706 VS2SC3928AR-1Y J 2SC3928AR AB
Q1710 VSDTC144EE/-1Y J DTC144EE AA
Q1711 VS2SA1037KQ-1Y J 2SA1037KQ AA
Q1712 VSFMMT718//-1Y J FMMT718 AE
Q1713 VSDTC144EE/-1Y J DTC144EE AA
Q2005 VSDTC114YE/-1Y J DTC114YE AB
Q2019 VSDTC114EE/-1Y J DTC114EE AB
Q2020 VS2SA1037KQ-1Y J 2SA1037KQ AA
Q2021 VSDTC144EE/-1Y J DTC144EE AA
Q2022 VSDTA144EE/-1Y J DTC144EE AA
DIODES
D701 VHDRB051L40-1Y J Diode AD
D702 VHDRB051L40-1Y J Diode AD
D703 VHDRB051L40-1Y J Diode AD
D704 VHDSFPB56//2EY J Diode AC
D706 VHDRF071M2S-1Y J Diode AD
D708 VHDRB160M40-1Y J Diode AC
D709 VHD1SS355//-1Y J Diode AB
D801 VHDDAN222//-1Y J Diode AA
D1703 VHDDAN222//-1Y J Diode AA
D1706 VHDDAN222//-1Y J Diode AA
D1708 VHDRB521S30-1Y J Diode AC
D1709 VHDDAN222//-1Y J Diode AA
D2002 VHDDAN202K/-1Y J Diode AB
D2007 VHDRB491D++-1Y J Diode AD
PACKAGED CIRCUITS
X801 RCRSCA097WJZZY J Crystal, 54MHz AG

Ref. No. Part No. ★Description Code Ref. No. Part No. ★Description Code
31
LC-20S4U-S
SUPPLEMENT
DUNTKD234FE21
MAIN Unit (Continued)
X2001 RCRSC0032TAZZY J Crystal, 32.768kHz AG
FILTER AND COILS
FL2001 RFiLZA003WJPZY J Filter AD
L701 RCiLPA154WJZZY J Coil AE
L702 RCiLPA154WJZZY J Coil AE
L703 RCiLPA154WJZZY J Coil AE
L802 VPCNN220J2R9NY J Peaking 22µH AB
L1702 VPCNN470J5R4NY J Peaking 47µH AB
L1703 VPCUN100KR42NY J Peaking 10µH AB
TRANSFORMER
T701 RTRNWA141WJZZY J Transformer AG
CAPACITORS
C703 VCKYCY1EF104ZY J 0.1 25V Ceramic AA
C704 VCKYCY1EB333KY J 0.033 25V Ceramic AA
C705 VCKYCY1EB333KY J 0.033 25V Ceramic AA
C706 VCKYCY1EB333KY J 0.033 25V Ceramic AA
C707 VCKYCY1EB333KY J 0.033 25V Ceramic AA
C708 VCKYCY1EF104ZY J 0.1 25V Ceramic AA
C710 VCKYCY1HB332KY J 3300p 50V Ceramic AA
C711 VCCCCY1HH102JY J 1000p 50V Ceramic AB
C713 VCCCCY1HH102JY J 1000p 50V Ceramic AB
C714 VCCCCY1HH331JY J 330p 50V Ceramic AA
C715 VCCCCY1HH330JY J 33p 50V Ceramic AA
C719 VCCCCY1HH151JY J 150p 50V Ceramic AA
C720 VCCCCY1HH330JY J 33p 50V Ceramic AA
C721 VCCCCY1HH101JY J 100p 50V Ceramic AA
C722 VCCCCY1HH101JY J 100p 50V Ceramic AA
C723 VCCCCY1HH181JY J 180p 50V Ceramic AA
C724 VCKYTV1EB473KY J 0.047 25V Ceramic AB
C725 VCKYCY1EB123KY J 0.012 25V Ceramic AA
C726 VCKYCY1EF104ZY J 0.1 25V Ceramic AA
C727 VCKYCY1EB123KY J 0.012 25V Ceramic AA
C728 RC-KZA109WJZZY J 10 16V Ceramic AC
C729 RC-KZA109WJZZY J 10 16V Ceramic AC
C730 RC-KZA109WJZZY J 10 16V Ceramic AC
C731 VCKYCY1HB272KY J 2700p 50V Ceramic AA
C732 VCKYCY1EB223KY J 0.022 25V Ceramic AA
C733 VCCCCY1HH102JY J 1000p 50V Ceramic AB
C734 VCCCCY1HH102JY J 1000p 50V Ceramic AB
C735 RC-KZA101WJZZY J 10 6.3V Ceramic AC
C736 RC-KZA101WJZZY J 10 6.3V Ceramic AC
C737 RC-KZA110WJZZY J 10 25V Ceramic AD
C738 RC-KZA108WJZZY J 10 10V Ceramic AC
C739 RC-KZA108WJZZY J 10 10V Ceramic AC
C741 VCKYCY1HB562KY J 5600p 50V Ceramic AA
C742 VCEASX1CN106MY J 10 16V Electrolytic AC
C744 RC-KZA215WJZZY J 1 50V Ceramic AC
C745 RC-KZA109WJZZY J 10 16V Ceramic AC
C749 RC-KZA109WJZZY J 10 16V Ceramic AC
C801 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C802 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C803 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C804 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C805 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C806 VCKYCY1CB104KY J 0.1 16V Ceramic AB
C807 VCKYCY1CB104KY J 0.1 16V Ceramic AB
C808 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C809 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C810 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C811 VCKYCY1CB104KY J 0.1 16V Ceramic AB
C812 VCKYCY1CB104KY J 0.1 16V Ceramic AB
C813 VCKYCY1EB333KY J 0.033 25V Ceramic AA
C814 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C815 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C816 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C817 VCKYCY1HB104KY J 0.1 50V Ceramic AA
C818 VCKYCY1CB104KY J 0.1 16V Ceramic AB
C819 VCKYCY1HB104KY J 0.1 50V Ceramic AA
C820 VCKYCY1CB104KY J 0.1 16V Ceramic AB
C821 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C822 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C823 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C824 VCKYCY1HB104KY J 0.1 50V Ceramic AA
C825 VCKYCY1CB104KY J 0.1 16V Ceramic AB
C826 VCKYCY1HB104KY J 0.1 50V Ceramic AA
C827 VCKYCY1HB104KY J 0.1 50V Ceramic AA
C828 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C829 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C830 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C831 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C832 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C833 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C834 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C835 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C836 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C837 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C838 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C839 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C840 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C841 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C842 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C843 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C844 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C845 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C846 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C847 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C848 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C849 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C850 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C851 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C852 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C853 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C854 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C855 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C856 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C857 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C858 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C859 VCKYCZ1AB333KY J 0.033 10V Ceramic AB
C860 RC-KZA101WJZZY J 10 6.3V Ceramic AC
C861 RC-KZA101WJZZY J 10 6.3V Ceramic AC
C862 RC-KZA101WJZZY J 10 6.3V Ceramic AC
C863 VCKYCY1HB104KY J 0.1 50V Ceramic AA
C864 VCKYCY1HB104KY J 0.1 50V Ceramic AA
C865 VCCCCY1HH5R0CY J 5p 50V Ceramic AA
C866 VCCCCY1HH5R0CY J 5p 50V Ceramic AA
C867 RC-KZA101WJZZY J 10 6.3V Ceramic AC
C872 VCEASX0JN227MY J 220 6.3V Electrolytic AC
C874 VCKYCZ1AB104KY J 0.1 10V Ceramic AB
C875 VCKYCY1HB103KY J 0.01 50V Ceramic AA
C876 VCKYCY1HB102KY J 1000p 50V Ceramic AA
C877 VCEASX0JN476MY J 47 6.3V Electrolytic AC
C878 VCKYCY1AF105ZY J 1 10V Ceramic AC
C886 VCEASY1CN477MY J 470 16V Electrolytic AD
C887 VCKYCY1HB103KY J 0.01 50V Ceramic AA
C1101 RC-KZA101WJZZY J 10 6.3V Ceramic AC
C1102 VCKYCY1EF104ZY J 0.1 25V Ceramic AA
C1103 RC-KZA110WJZZY J 10 25V Ceramic AD
C1104 VCKYCY1EF104ZY J 0.1 25V Ceramic AA
C1105 RC-KZA111WJZZY J 1 25V Ceramic AC
C1106 RC-KZA111WJZZY J 1 25V Ceramic AC
C1107 VCKYCY1HB102KY J 1000p 50V Ceramic AA
C1108 VCKYCY1HB102KY J 1000p 50V Ceramic AA
C1109 VCKYCY1EF104ZY J 0.1 25V Ceramic AA
C1132 RC-KZA109WJZZY J 10 16V Ceramic AC
C1201 VCKYCY1HB103KY J 0.01 50V Ceramic AA
C1202 VCKYCY1HB103KY J 0.01 50V Ceramic AA
C1203 VCKYCY1HB103KY J 0.01 50V Ceramic AA
C1204 VCKYCY1HB103KY J 0.01 50V Ceramic AA
C1205 VCKYCY1HB103KY J 0.01 50V Ceramic AA
C1206 RC-KZA108WJZZY J 10 10V Ceramic AC
C1207 RC-KZA108WJZZY J 10 10V Ceramic AC
C1208 VCKYCY1HB104KY J 0.1 50V Ceramic AA
C1209 VCKYCY1HB104KY J 0.1 50V Ceramic AA