Sharp Aquos LC-42D~43U User manual

SHAI~~
LC-42D~43U
LC-46D·43U
LC-52D
l43U
LIQUID CRYSTAL TELEVISION
TELI~VISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LiQUIDO
OPERATION MANUAL
MODE D'EMPLOI
MANUAL DE OPERACION
HIGH DEFINITION MULTIMEDIA INTERFACE
LC-46D43U/LC-52D43U
tlLlJT./ [)(]IDOLBVI
HI~H.DEFINITION TELEVISION DIG I TAL
LC-42D43U
AQuas
•
II~i*{§·"i"';i
N0M 1245
~ 1tJ.1Iio.. IMPORTANT :Please read this operation manual before starting operating the equipment.
~y~r IMPORTANTE: Lea este manual de operaci6n antes de comenzar aoperar el equipo.
SHAI~~
LC-42D~43U
LC-46D·43U
LC-52D
l43U
LIQUID CRYSTAL TELEVISION
TELI~VISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LiQUIDO
OPERATION MANUAL
MODE D'EMPLOI
MANUAL DE OPERACION
HIGH DEFINITION MULTIMEDIA INTERFACE
LC-46D43U/LC-52D43U
tlLlJT./ [)(]IDOLBVI
HI~H.DEFINITION TELEVISION DIG I TAL
LC-42D43U
AQuas
•
II~i*{§·"i"';i
N0M 1245
~ 1tJ.1Iio.. IMPORTANT :Please read this operation manual before starting operating the equipment.
~y~r IMPORTANTE: Lea este manual de operaci6n antes de comenzar aoperar el equipo.

LC-42D43U
LC-46D43U
LC-52D43U
LIQUID CRYSTAL TELEVISION
ENGLISH
OPERATION MANUAL
•The illustrations and on-screen displays in this operation
manual are for explanation purposes and may vary slightly from
the actual operations.
•Menu items that are not selectable are grayed out.
•The examples used throughout this manual are based on the
LC-46D43U model.
IMPORTANT:
To aid reporting in case of loss or theft, please record the
N's model and serial numbers in the space provided. The
numbers are located at the rear of the
N.
IModel No
Serial No.:
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
The lightning flash with arrow-head
symbol, within an equilateral triangle,
is intended to alert the user to the
presence
of uninsulated "dangerous
voltage" within the product's
enclosure that may be
of sufficient
magnitude
to constitute arisk of
electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a
triangle
is intended to alert the user
to the presence of important
operating and maintenance
(servicing) instructions
in the
literature accompanying the product.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
(®-1
LC-42D43U
LC-46D43U
LC-52D43U
LIQUID CRYSTAL TELEVISION
ENGLISH
OPERATION MANUAL
•The illustrations and on-screen displays in this operation
manual are for explanation purposes and may vary slightly from
the actual operations.
•Menu items that are not selectable are grayed out.
•The examples used throughout this manual are based on the
LC-46D43U model.
IMPORTANT:
To aid reporting in case of loss or theft, please record the
N's model and serial numbers in the space provided. The
numbers are located at the rear of the
N.
IModel No
Serial No.:
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
The lightning flash with arrow-head
symbol, within an equilateral triangle,
is intended to alert the user to the
presence
of uninsulated "dangerous
voltage" within the product's
enclosure that may be
of sufficient
magnitude
to constitute arisk of
electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a
triangle
is intended to alert the user
to the presence of important
operating and maintenance
(servicing) instructions
in the
literature accompanying the product.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
(®-1

IMPORTANT INFORMATION
CAUTION:
DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND, TRIPOD, BRACKET, OR TABLE.
THE PRODUCT MAY FALL CAUSING SERIOUS PERSONAL INJURY AND SERIOUS DAMAGE TO
THE PRODUCT. USE ONLY WITH A
CART, STAND, TRIPOD, BRACKET, OR TABLE RECOMMENDED
BY THE MANUFACTURER
OR SOLD WITH THE PRODUCT. FOLLOW THE MANUFACTURER'S
INSTRUCTIONS WHEN INSTALLING THE PRODUCT AND USE MOUNTING ACCESSORIES
RECOMMENDED BY THE MANUFACTURER. APRODUCT AND CART COMBINATION SHOULD BE
MOVED WITH CARE. QUICK STOPS, EXCESSIVE FORCE, AND UNEVEN SURFACES MAY CAUSE
THE PRODUCT AND CART COMBINATION TO OVERTURN.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly
approved by the manufacturer could void the user's authority to operate this equipment.
CAUTION:
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded
cables and connectors for connections.
DECLARATION OF CONFORMITY:
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-42D43U/LC-46D43U/LC-52D43U
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RESPONSIBLE PARTY:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
TEL: 1-800-BE-SHARP
For Business Customers: URL http://www.sharpusa.com
INFORMATION:
This equipment has been tested and found to comply with the limits for aClass Bdigital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the
instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not
occur
in aparticular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
follOWing measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment
and receiver.
-Connect the equipment into
an outlet on acircuit different from that to which the receiver is connected.
-Consult the dealer or
an experienced radiofTV technician for help.
"Note to
CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National
Electrical Code that provides gUidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as practical."
This product utilizes tin-lead solder, and fluorescent lamp containing asmall amount of
mercury. Disposal of these materials may be regulated due to environmental
considerations. For disposal or recycling information, please contact your local
authorities, the Electronic Industries Alliance: www.eiae.org, the lamp recycling
organization: www.lamprecycle.org or Sharp at 1-800-BE-SHARP
(For U.S.A. Only)
Trademarks
•Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby
Laboratories.
•"HDMI, the
HDMIIogo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC."
•Products that have earned the ENERGY STAR® are designed to protect the environment through superior energy
efficiency.
@-2
IMPORTANT INFORMATION
CAUTION:
DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND, TRIPOD, BRACKET, OR TABLE.
THE PRODUCT MAY FALL CAUSING SERIOUS PERSONAL INJURY AND SERIOUS DAMAGE TO
THE PRODUCT. USE ONLY WITH A
CART, STAND, TRIPOD, BRACKET, OR TABLE RECOMMENDED
BY THE MANUFACTURER
OR SOLD WITH THE PRODUCT. FOLLOW THE MANUFACTURER'S
INSTRUCTIONS WHEN INSTALLING THE PRODUCT AND USE MOUNTING ACCESSORIES
RECOMMENDED BY THE MANUFACTURER. APRODUCT AND CART COMBINATION SHOULD BE
MOVED WITH CARE. QUICK STOPS, EXCESSIVE FORCE, AND UNEVEN SURFACES MAY CAUSE
THE PRODUCT AND CART COMBINATION TO OVERTURN.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly
approved by the manufacturer could void the user's authority to operate this equipment.
CAUTION:
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded
cables and connectors for connections.
DECLARATION OF CONFORMITY:
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-42D43U/LC-46D43U/LC-52D43U
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RESPONSIBLE PARTY:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
TEL: 1-800-BE-SHARP
For Business Customers: URL http://www.sharpusa.com
INFORMATION:
This equipment has been tested and found to comply with the limits for aClass Bdigital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the
instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not
occur
in aparticular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
follOWing measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment
and receiver.
-Connect the equipment into
an outlet on acircuit different from that to which the receiver is connected.
-Consult the dealer or
an experienced radiofTV technician for help.
"Note to
CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National
Electrical Code that provides gUidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as practical."
This product utilizes tin-lead solder, and fluorescent lamp containing asmall amount of
mercury. Disposal of these materials may be regulated due to environmental
considerations. For disposal or recycling information, please contact your local
authorities, the Electronic Industries Alliance: www.eiae.org, the lamp recycling
organization: www.lamprecycle.org or Sharp at 1-800-BE-SHARP
(For U.S.A. Only)
Trademarks
•Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby
Laboratories.
•"HDMI, the
HDMIIogo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC."
•Products that have earned the ENERGY STAR® are designed to protect the environment through superior energy
efficiency.
@-2

DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years
of trouble-free operation
of your product, please read the Important Safety Instructions carefully before
using this product.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage
if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
However, improper use can result in electric shock
and/or fire. In order to prevent potential danger, please
observe the following instructions when installing, operating and cleaning the product.
To ensure your safety
and prolong the service life
of your Liquid Crystal Television, please read the following precautions carefully
before using the product.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. Apolarized plug has two blades
with one
wider than the other. Agrounding type plug has two blades and athird grounding prong. The
wide blade
or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician
for replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold ~
with the apparatus. When acart is used, use caution when moving the cart/apparatus
combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused
for long periods of time.
14) Refer all servicing
to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally,
or has been dropped.
Additional Safety Information
15) Power Sources- This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the
type of power supply to your home, consult your product dealer or
local
power company. For products intended to operate from battery power, or other sources, refer to the
operating instructions.
16) Overloading-Do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in arisk
of fire or electric shock.
17) Object and Liquid Entry-Never push objects of any kind into this product through openings as they may
touch dangerous voltage points
or short-out parts that could result in afire or electric shock. Never spill
liquid
of any kind on the product.
18) Damage Requiring
Service- Unplug this product from the wall outlet and refer servicing to qualified
service personnel underthe following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an improper adjustment
of other controls may result in damage and will often require extensive work by aqualified technician
to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance -this indicates aneed for service.
19) Replacement
Parts-When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer
or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
20) Safety Check-Upon completion
of any service or repairs to this product, ask the service technician to
perform safety checks
to determine that the product is in proper operating condition.
21) Wall
or ceiling mounting-When mounting the product on awall or ceiling, be sure to install the product
according
to the method recommended by the manufacturer.
@-3
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years
of trouble-free operation
of your product, please read the Important Safety Instructions carefully before
using this product.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage
if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
However, improper use can result in electric shock
and/or fire. In order to prevent potential danger, please
observe the following instructions when installing, operating and cleaning the product.
To ensure your safety
and prolong the service life
of your Liquid Crystal Television, please read the following precautions carefully
before using the product.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. Apolarized plug has two blades
with one
wider than the other. Agrounding type plug has two blades and athird grounding prong. The
wide blade
or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician
for replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold ~
with the apparatus. When acart is used, use caution when moving the cart/apparatus
combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused
for long periods of time.
14) Refer all servicing
to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally,
or has been dropped.
Additional Safety Information
15) Power Sources- This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the
type of power supply to your home, consult your product dealer or
local
power company. For products intended to operate from battery power, or other sources, refer to the
operating instructions.
16) Overloading-Do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in arisk
of fire or electric shock.
17) Object and Liquid Entry-Never push objects of any kind into this product through openings as they may
touch dangerous voltage points
or short-out parts that could result in afire or electric shock. Never spill
liquid
of any kind on the product.
18) Damage Requiring
Service- Unplug this product from the wall outlet and refer servicing to qualified
service personnel underthe following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an improper adjustment
of other controls may result in damage and will often require extensive work by aqualified technician
to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance -this indicates aneed for service.
19) Replacement
Parts-When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer
or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
20) Safety Check-Upon completion
of any service or repairs to this product, ask the service technician to
perform safety checks
to determine that the product is in proper operating condition.
21) Wall
or ceiling mounting-When mounting the product on awall or ceiling, be sure to install the product
according
to the method recommended by the manufacturer.
@-3

IMPORTANT SAFETY INSTRUCTIONS
•Water and Moisture - Do not use this product near water -for example, near abath tub, wash
bowl, kitchen sink, or laundry tub; in awet basement; or near aswimming pool; and the like.
•Stand -Do not place the product on
an unstable cart, stand, tripod or table. Placing the
product on an unstable base can cause the product to fall, resulting in serious personal injuries
as well as damage to the product. Use only acart, stand, tripod, bracket or table recommended
by the manufacturer or sold with the product. When mounting the product on awall, be sure to
follow the manufacturer's instructions. Use only the mounting hardware recommended by the
manufacturer.
•Selecting the location -Select aplace with no direct sunlight and good ventilation.
•Ventilation -The vents and other openings
in the cabinet are designed for ventilation. Do not
&==Jl
cover or block these vents and openings since insufficient ventilation can cause overheating
.'
,
,.
and/or shorten the life of the product. Do not place the product on abed, sofa, rug or other 0
similar suriace, since they can block ventilation openings. This product is not designed for built-
in installation; do not place the product in an enclosed place such as abookcase or rack, unless
proper ventilation is provided or the manufacturer's instructions are followed.
•The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when the
product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in
case the panel breaks.
•Heat -The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
•The Liquid Crystal panel
is avery high technology product with 3,147,264 thin film transistors, giving you fine picture details.
Occasionally, afew non-active pixels may appear on the screen as afixed point of blue, green or red. Please note that this
does not affect the periormance of your prodUCt.
Precautions when transporting the TV
•Be sure to always carry the TV by two people holding it with two hands -one hand on
each side of the
TV.
•Lightning -For added protection for this television equipment during alightning storm, or G~' ~Dfit/ 1/',./"
when it is left unattended and unused for long periods of time, unplug it from the wall outlet .
and disconnect the antenna. This will prevent damage to the equipment due to lightning and
power-line surges.
&---8
•Power Lines -An outside antenna system should not be located in the vicinity of overhead l6:I
power lines or other electric light or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them might be fatal.
@-4
IMPORTANT SAFETY INSTRUCTIONS
•Water and Moisture - Do not use this product near water -for example, near abath tub, wash
bowl, kitchen sink, or laundry tub; in awet basement; or near aswimming pool; and the like.
•Stand -Do not place the product on
an unstable cart, stand, tripod or table. Placing the
product on an unstable base can cause the product to fall, resulting in serious personal injuries
as well as damage to the product. Use only acart, stand, tripod, bracket or table recommended
by the manufacturer or sold with the product. When mounting the product on awall, be sure to
follow the manufacturer's instructions. Use only the mounting hardware recommended by the
manufacturer.
•Selecting the location -Select aplace with no direct sunlight and good ventilation.
•Ventilation -The vents and other openings
in the cabinet are designed for ventilation. Do not
&==Jl
cover or block these vents and openings since insufficient ventilation can cause overheating
.'
,
,.
and/or shorten the life of the product. Do not place the product on abed, sofa, rug or other 0
similar suriace, since they can block ventilation openings. This product is not designed for built-
in installation; do not place the product in an enclosed place such as abookcase or rack, unless
proper ventilation is provided or the manufacturer's instructions are followed.
•The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when the
product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in
case the panel breaks.
•Heat -The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
•The Liquid Crystal panel
is avery high technology product with 3,147,264 thin film transistors, giving you fine picture details.
Occasionally, afew non-active pixels may appear on the screen as afixed point of blue, green or red. Please note that this
does not affect the periormance of your prodUCt.
Precautions when transporting the TV
•Be sure to always carry the TV by two people holding it with two hands -one hand on
each side of the
TV.
•Lightning -For added protection for this television equipment during alightning storm, or G~' ~Dfit/ 1/',./"
when it is left unattended and unused for long periods of time, unplug it from the wall outlet .
and disconnect the antenna. This will prevent damage to the equipment due to lightning and
power-line surges.
&---8
•Power Lines -An outside antenna system should not be located in the vicinity of overhead l6:I
power lines or other electric light or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them might be fatal.
@-4

IMPORTANT SAFETY INSTRUCTIONS
•Outdoor Antenna Grounding -If an outside antenna is connected to the television equipment, be sure the antenna
system is grounded so as to provide some protection against voltage surges and built-up static charges.
Article
810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS
PER
NATIONAL ELECTRICAL CODE, ANSIINFPA 70
NEC -NATIONAL ELECTRICAL CODE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
;--'l........;;::::::.l. GROUNDING CONDUCTORS
(NEC SECTION 810-21)
~~~ GROUND CLAMPS
.,.- POWER SERVICE GROUNDING ELECTRODE
SYSTEM
(NEC ART 250, PART
H)
•To prevent fire, never place any type of candle or flames on the top or near the TV set.
•To prevent fire or shock hazard,
do not expose this product to dripping or splashing.
No objects filled with liquids, such as vases, should be placed on the product.
•To prevent fire or shock hazard, do not place the AC cord under the
TV set or other heavy
items. b
d~ )'
"q
•Turn off the main power and unplug the AC cord from the wall outlet before handling.
•Use asoft cloth and gently wipe the surface of the display panel. Using ahard cloth may
scratch the panel surface. r::
•Use asoft damp cloth to gently wipe the panel when it is really dirty. ~
(It may scratch the panel surface when wiped strongly.)
•
If the panel is dusty, use an anti-static brush, which is commercially available, to clean it.
•To protect the panel,
do not use adirty cloth, liquid cleaners or chemical cloth to clean it,
such materials may damage the panel surface.
•To clean the outer cabinet. use the same method. Do not use liquid or aerosol cleaners.
•Do not display astill picture for along time, as this could cause
an afterimage to remain.
@-5
IMPORTANT SAFETY INSTRUCTIONS
•Outdoor Antenna Grounding -If an outside antenna is connected to the television equipment, be sure the antenna
system is grounded so as to provide some protection against voltage surges and built-up static charges.
Article
810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS
PER
NATIONAL ELECTRICAL CODE, ANSIINFPA 70
NEC -NATIONAL ELECTRICAL CODE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
;--'l........;;::::::.l. GROUNDING CONDUCTORS
(NEC SECTION 810-21)
~~~ GROUND CLAMPS
.,.- POWER SERVICE GROUNDING ELECTRODE
SYSTEM
(NEC ART 250, PART
H)
•To prevent fire, never place any type of candle or flames on the top or near the TV set.
•To prevent fire or shock hazard,
do not expose this product to dripping or splashing.
No objects filled with liquids, such as vases, should be placed on the product.
•To prevent fire or shock hazard, do not place the AC cord under the
TV set or other heavy
items. b
d~ )'
"q
•Turn off the main power and unplug the AC cord from the wall outlet before handling.
•Use asoft cloth and gently wipe the surface of the display panel. Using ahard cloth may
scratch the panel surface. r::
•Use asoft damp cloth to gently wipe the panel when it is really dirty. ~
(It may scratch the panel surface when wiped strongly.)
•
If the panel is dusty, use an anti-static brush, which is commercially available, to clean it.
•To protect the panel,
do not use adirty cloth, liquid cleaners or chemical cloth to clean it,
such materials may damage the panel surface.
•To clean the outer cabinet. use the same method. Do not use liquid or aerosol cleaners.
•Do not display astill picture for along time, as this could cause
an afterimage to remain.
@-5

Supplied accessories
Make sure the following accessories are provided with the product.
Page 9Page 9Page 8
Page 8Page 8Page 8
•LC-46D43U/LC-52D43U
Page 7
•LC-42D43U
Page 7
SHAR~
~
•Always use the AC cord supplied with the W .
•AC cord enclosed
in this product is for 11 0-125V. In using it on the 125-240VAC, please consult to the following.
SHARP ELECTRONICS CORPORATION, LATIN AMERICA GROUP
6100 Blue Lagoon Drive, Suite 150, Miami, Florida 33126, U.S.A.
@-6
Supplied accessories
Make sure the following accessories are provided with the product.
Page 9Page 9Page 8
Page 8Page 8Page 8
•LC-46D43U/LC-52D43U
Page 7
•LC-42D43U
Page 7
SHAR~
~
•Always use the AC cord supplied with the W .
•AC cord enclosed
in this product is for 11 0-125V. In using it on the 125-240VAC, please consult to the following.
SHARP ELECTRONICS CORPORATION, LATIN AMERICA GROUP
6100 Blue Lagoon Drive, Suite 150, Miami, Florida 33126, U.S.A.
@-6

QUICK REFERENCE
•Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
•Before performing work spread cushioning over the
base area to lay the 1V on. This will prevent it from being damaged.
~
•Attach the stand in the correct direction.
•Be sure to follow the instructions. Incorrect installation of the stand may result
in the TV falling over.
@·7
CD Insert the stand into the openings on the
bottom of the
TV.
®Insert and tighten the 4long screws into
the 4 holes on the rear of the
TV.
Hexkey-®~
I
BJmm
• To detach the stand, perform the steps in reverse order.
BJmm
• To detach the stand, perform the steps in reverse order.
~~ii ,~,~
CD Set the post for the stand unit onto the box.
®Attach the base to the post.
@Insert and tighten the 4short screws into
the 4 holes on the bottom of the base.
Attach the
two supporting posts for the stand
unit onto the base using the box for the stand
unit as shown below.
(Close-up of the upper side of the stand unit)
•LC-46D43U1LC-52D43U
Confirm that there are 10 screws (6 short
screws and 4long screws) supplied with the 1V.
//_::=- .. a ~ %@J
?' /.' "'.-®.~.,I~
. / .. ?~~~~
~,,~~~p
'-/'''~ t
t .
~'PJ Hex key
Short screw r
1Insert each of the protrusions on the two
supporting posts into the openings on the
upper side of the base.
2Insert and tighten the 6short screws with
the hex key (supplied with the product)
in the
order of
CD, ®and @ .
•LC-42D43U
Confirm that there are 8screws (4 short screws
and 4long screws) supplied with the
TV.
QUICK REFERENCE
•Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
•Before performing work spread cushioning over the
base area to lay the 1V on. This will prevent it from being damaged.
~
•Attach the stand in the correct direction.
•Be sure to follow the instructions. Incorrect installation of the stand may result
in the TV falling over.
@·7
CD Insert the stand into the openings on the
bottom of the
TV.
®Insert and tighten the 4long screws into
the 4 holes on the rear of the
TV.
Hexkey-®~
I
BJmm
• To detach the stand, perform the steps in reverse order.
BJmm
• To detach the stand, perform the steps in reverse order.
~~ii ,~,~
CD Set the post for the stand unit onto the box.
®Attach the base to the post.
@Insert and tighten the 4short screws into
the 4 holes on the bottom of the base.
Attach the
two supporting posts for the stand
unit onto the base using the box for the stand
unit as shown below.
(Close-up of the upper side of the stand unit)
•LC-46D43U1LC-52D43U
Confirm that there are 10 screws (6 short
screws and 4long screws) supplied with the 1V.
//_::=- .. a ~ %@J
?' /.' "'.-®.~.,I~
. / .. ?~~~~
~,,~~~p
'-/'''~ t
t .
~'PJ Hex key
Short screw r
1Insert each of the protrusions on the two
supporting posts into the openings on the
upper side of the base.
2Insert and tighten the 6short screws with
the hex key (supplied with the product)
in the
order of
CD, ®and @ .
•LC-42D43U
Confirm that there are 8screws (4 short screws
and 4long screws) supplied with the
TV.

QUICK REFERENCE
Ventilation &Cleaning Tips
Keep your AQUaS television in awell ventilated area and make sure not to place it by aheat source or use near
water. The
AQUaS television is designed for AC use only and should be used with supplied AC cord.
Clean the screen
by spraying asoft lint free cloth (supplied) with water to lightly moisten. Gently ~ ~,;c .. '<,
wipe and avoid pressing on the screen. To clean the outer cabinet, use the same method. Do D- l~
not use liquid or aerosol cleaners. -
The screen
is glass and can be scratched or broken when dropped or impacted.
STOP! To safely remove the AQUOS television from the box
•It's best to use 2people to remove the AQUaS television for stability.
•Lift
onto installation location as the diagram illustrates.
QUICK INSTALLATION TIPS
Attach your antenna to the back of the AQUaS
television. (See page 13.)
Connect the AC plug for the AQUaS television
into
the AC outlet.
W
'---·
: I __ t.
.. , .~
.. .....-,
,, __ ~ .•• o
-- -- ~
~
'------l,'r---c::::J3 "lAC outlet I
•Place the 1V close to the AC outlet, and keep the power
plug within reach.
How to turn on the AQUaS television for the
first time.
A) Press POWER on the AQUaS television.
, __ ~_VO_l _+ _c:::::::J_V_CH_A __ 9_UT __ ~_rnl_
POWER
B) The paWER indicator on the front of the
AQUaS television lights GREEN.
,J
POWER SlEEP OPe
o0 eI 0 0
BED
•TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH UN-INSULATED PARTS OF ANY CABLES
WITH THE AC CORD CONNECTED.
_-I-----=::=:J~
Place the Ferrite core in the space indicated in
the below figure and bundle the cords properly
with cable
clamps and acable tie.
Ferrite core
POWER indicator
BED
•Speakers cannot be detached from the 1V .
• 1V angle cannot be adjusted.
@-8
QUICK REFERENCE
Ventilation &Cleaning Tips
Keep your AQUaS television in awell ventilated area and make sure not to place it by aheat source or use near
water. The
AQUaS television is designed for AC use only and should be used with supplied AC cord.
Clean the screen
by spraying asoft lint free cloth (supplied) with water to lightly moisten. Gently ~ ~,;c .. '<,
wipe and avoid pressing on the screen. To clean the outer cabinet, use the same method. Do D- l~
not use liquid or aerosol cleaners. -
The screen
is glass and can be scratched or broken when dropped or impacted.
STOP! To safely remove the AQUOS television from the box
•It's best to use 2people to remove the AQUaS television for stability.
•Lift
onto installation location as the diagram illustrates.
QUICK INSTALLATION TIPS
Attach your antenna to the back of the AQUaS
television. (See page 13.)
Connect the AC plug for the AQUaS television
into
the AC outlet.
W
'---·
: I __ t.
.. , .~
.. .....-,
,, __ ~ .•• o
-- -- ~
~
'------l,'r---c::::J3 "lAC outlet I
•Place the 1V close to the AC outlet, and keep the power
plug within reach.
How to turn on the AQUaS television for the
first time.
A) Press POWER on the AQUaS television.
, __ ~_VO_l _+ _c:::::::J_V_CH_A __ 9_UT __ ~_rnl_
POWER
B) The paWER indicator on the front of the
AQUaS television lights GREEN.
,J
POWER SlEEP OPe
o0 eI 0 0
BED
•TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH UN-INSULATED PARTS OF ANY CABLES
WITH THE AC CORD CONNECTED.
_-I-----=::=:J~
Place the Ferrite core in the space indicated in
the below figure and bundle the cords properly
with cable
clamps and acable tie.
Ferrite core
POWER indicator
BED
•Speakers cannot be detached from the 1V .
• 1V angle cannot be adjusted.
@-8

QUICK REFERENCE
If the remote control fails to operate TV functions, replace the batteries in the remote control unit.
1Open the battery cover. 2Insert
two "AAA" size batteries
(supplied with the product). 3Close the battery cover.
•Place the batteries with their terminals
corresponding to the (+)and (- )
indications
in the battery compartment.
Improper use of batteries can result
in chemical leakage or explosion. Be sure to follow the instructions below.
•Do not mix batteries of different types. Different types of batteries have different characteristics.
•Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical
leakage
in old batteries.
•Remove batteries as soon as .hey are worn out. Chernicals that leak from batteries that come
in contact with skin can cause a
rash. If you find any chemical leakage, wipe thoroughly with acloth.
•The batteries supplied with this product may have ashorter life expectancy due to storage conditions.
•
If you will not be using the remote control unit for an extended period of tirne, rernove batteries from it.
.-
Remote control sensor
dPOWER SLEEP ope )
00 0 0
&
I .. '"
17' (5m) II .
30°'----
30°
I30°
~
~
!U
:::
:~
.. II ..
~
~
~
.:
g C.~~T:; =8: I
SOURCE LIGHT
(38 ®
8 G 8
REC
000
8 8 @ID
If the POWER indicator on the AQUOS television still does not light up, press TV POWER
on the remote control to turn the power on.
IMPORTANT:
IF THE UNIT DOES NOT POWER ON -UNPLUG THE AQUOS TELEVISION FROM THE OUTLET AND REPEAT
THE INSTALLATION STEPS.
IMPORTANT:
The POWER indicator on the AQUOS television should light GREEN indicating you have
power
to the AQUOS television.
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT US AT 1-800-BE-SHARP.
Please refer
to the BASIC ADJUSTMENT SETTINGS SECTION for EZ Setup and basic channel setup functions
and USING EXTERNAL EQUIPMENT SECTION for other device connections
(DVD, VCR, AUDIO, etc.) in your
AQUOS operation manual.
@- 9
QUICK REFERENCE
If the remote control fails to operate TV functions, replace the batteries in the remote control unit.
1Open the battery cover. 2Insert
two "AAA" size batteries
(supplied with the product). 3Close the battery cover.
•Place the batteries with their terminals
corresponding to the (+)and (- )
indications
in the battery compartment.
Improper use of batteries can result
in chemical leakage or explosion. Be sure to follow the instructions below.
•Do not mix batteries of different types. Different types of batteries have different characteristics.
•Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical
leakage
in old batteries.
•Remove batteries as soon as .hey are worn out. Chernicals that leak from batteries that come
in contact with skin can cause a
rash. If you find any chemical leakage, wipe thoroughly with acloth.
•The batteries supplied with this product may have ashorter life expectancy due to storage conditions.
•
If you will not be using the remote control unit for an extended period of tirne, rernove batteries from it.
.-
Remote control sensor
dPOWER SLEEP ope )
00 0 0
&
I .. '"
17' (5m) II .
30°'----
30°
I30°
~
~
!U
:::
:~
.. II ..
~
~
~
.:
g C.~~T:; =8: I
SOURCE LIGHT
(38 ®
8 G 8
REC
000
8 8 @ID
If the POWER indicator on the AQUOS television still does not light up, press TV POWER
on the remote control to turn the power on.
IMPORTANT:
IF THE UNIT DOES NOT POWER ON -UNPLUG THE AQUOS TELEVISION FROM THE OUTLET AND REPEAT
THE INSTALLATION STEPS.
IMPORTANT:
The POWER indicator on the AQUOS television should light GREEN indicating you have
power
to the AQUOS television.
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT US AT 1-800-BE-SHARP.
Please refer
to the BASIC ADJUSTMENT SETTINGS SECTION for EZ Setup and basic channel setup functions
and USING EXTERNAL EQUIPMENT SECTION for other device connections
(DVD, VCR, AUDIO, etc.) in your
AQUOS operation manual.
@- 9

Contents
IMPORTANT INFORMATION 1
Trademarks 2
DEAR SHARP CUSTOMER 3
IMPORTANT SAFETY INSTRUCTIONS 3
Supplied accessories 6
QUICK REFERENCE 6
Attaching the stand 6
Contents 10
Part names
11
lV (Front) 11
lV (Rear/Top) 11
Remote control unit 12
Preparation 13
Using the remote control unit.. 13
Cautions regarding the remote control unit.. .. 13
Antennas 13
Connecting aBlu-ray disc player, HD-DVD player,
DVD player or a
DigitallV STB (Air or Cable) ... 14
Connecting aVCR, game console
or camcorder 14
Using Digital Audio Output 14
Connecting HDMI equipment 15
Connecting aPC 15
PC compatibility chart 15
Watching TV 16
Turning on the power 16
Turning off the power 16
Initial setup 17
Simple button operations for
changing channels 18
Simple button operations for
changing volume/sound 19
Setting MTS/SAP stereo mode 20
Setting Digital broadcasting audio mode 20
Basic adjustment settings 21
Menu operation buttons 21
On-Screen Display 21
Menu items for lV/INPUT 1/2/3 22
Menu items for HDMI/PC-IN 22
EZ Setup 23
Channel Setup 23
Antenna Setup -DIGITAL 24
Favorite channel setting 25
Picture adjustments 26
OPC setting 26
Advanced picture adjustments 27
Color Temperature 27
Black 27
I/P Setting 27
Film
Mode (3:2 pull-down) 27
3D-Y/C 27
Monochrome 27
Range of OPC 27
Sound adjustment 28
Surround 28
Power Control 29
Digital Setup 29
Audio Setup 29
@- 10
Using external equipment 30
Displaying an external equipment image 30
Input Select 30
Displaying an image from HDMI equipment.. 31
Input Skip 31
Useful adjustment settings 32
Auto Sync. adjustment
(for Analog PC input mode only) 32
Fine Sync. adjustment 32
Language setting 33
Image position 33
Reset 33
Input Label. 34
Sleep Timer 34
View Mode for 4:3 Programs 35
View Mode for HD Programs 35
View Mode (for PC input mode) 36
Advanced Option settings 37
Audio Only 37
Digital Noise Reduction 37
Output Select 37
Color System 37
Program Title Display 37
AV MODE 38
Input Signal (for Analog PC input mode only) 38
Closed Captions and Digital Closed Captions 39
Caption Setup 40
Secret number setting for parental control 41
Parental control (setting V-CHIP level) 43
How to temporarily release
the V-CHIP BLOCK 46
Reactivating the temporarily released
V-CHIP BLOCK 46
Other viewing options 47
Freezing images 47
Presetting remote control function 47
Appendix 51
Removing the stand 51
Setting the lV on the wall 51
Troubleshooting 52
Troubleshooting-Digital broadcasting 52
Specifications.................................... 53
Optional accessory 53
Information on the software license for this
product 55
Calling for Service 56
LIMITED WARRANTY 56
Dimensional drawings
•The dimensional drawings for the LCD 1V set are shown on
the inside back cover.
Contents
IMPORTANT INFORMATION 1
Trademarks 2
DEAR SHARP CUSTOMER 3
IMPORTANT SAFETY INSTRUCTIONS 3
Supplied accessories 6
QUICK REFERENCE 6
Attaching the stand 6
Contents 10
Part names
11
lV (Front) 11
lV (Rear/Top) 11
Remote control unit 12
Preparation 13
Using the remote control unit.. 13
Cautions regarding the remote control unit.. .. 13
Antennas 13
Connecting aBlu-ray disc player, HD-DVD player,
DVD player or a
DigitallV STB (Air or Cable) ... 14
Connecting aVCR, game console
or camcorder 14
Using Digital Audio Output 14
Connecting HDMI equipment 15
Connecting aPC 15
PC compatibility chart 15
Watching TV 16
Turning on the power 16
Turning off the power 16
Initial setup 17
Simple button operations for
changing channels 18
Simple button operations for
changing volume/sound 19
Setting MTS/SAP stereo mode 20
Setting Digital broadcasting audio mode 20
Basic adjustment settings 21
Menu operation buttons 21
On-Screen Display 21
Menu items for lV/INPUT 1/2/3 22
Menu items for HDMI/PC-IN 22
EZ Setup 23
Channel Setup 23
Antenna Setup -DIGITAL 24
Favorite channel setting 25
Picture adjustments 26
OPC setting 26
Advanced picture adjustments 27
Color Temperature 27
Black 27
I/P Setting 27
Film
Mode (3:2 pull-down) 27
3D-Y/C 27
Monochrome 27
Range of OPC 27
Sound adjustment 28
Surround 28
Power Control 29
Digital Setup 29
Audio Setup 29
@- 10
Using external equipment 30
Displaying an external equipment image 30
Input Select 30
Displaying an image from HDMI equipment.. 31
Input Skip 31
Useful adjustment settings 32
Auto Sync. adjustment
(for Analog PC input mode only) 32
Fine Sync. adjustment 32
Language setting 33
Image position 33
Reset 33
Input Label. 34
Sleep Timer 34
View Mode for 4:3 Programs 35
View Mode for HD Programs 35
View Mode (for PC input mode) 36
Advanced Option settings 37
Audio Only 37
Digital Noise Reduction 37
Output Select 37
Color System 37
Program Title Display 37
AV MODE 38
Input Signal (for Analog PC input mode only) 38
Closed Captions and Digital Closed Captions 39
Caption Setup 40
Secret number setting for parental control 41
Parental control (setting V-CHIP level) 43
How to temporarily release
the V-CHIP BLOCK 46
Reactivating the temporarily released
V-CHIP BLOCK 46
Other viewing options 47
Freezing images 47
Presetting remote control function 47
Appendix 51
Removing the stand 51
Setting the lV on the wall 51
Troubleshooting 52
Troubleshooting-Digital broadcasting 52
Specifications.................................... 53
Optional accessory 53
Information on the software license for this
product 55
Calling for Service 56
LIMITED WARRANTY 56
Dimensional drawings
•The dimensional drawings for the LCD 1V set are shown on
the inside back cover.

Part names
,----------- Remote control sensor
J
--------OPC sensor*
..•. P0
1
WER SL~'LE_P _OP_C _
I 0--- OPC indicator**
SLEEP indicator**
------ POWER indicator**
()
,
III
••• 0·"
.--dJ
R!m
*OPC: Optical Picture Control (See page 26.)
**See page 16 for 1V status indicator.
POWER button
INPUT button
AC INPUT terminal
Channel buttons
(CHV//\)
Volume
buttons
(vOL-I+)~
f~====::: ~I== ==,~I====, ~Il
DIGI AL AUDIO OUTPUT
terminal
INPUT 1terminals
INPUT 2terminals
AUDIO terminals (INPUT
5)
Antenna/Cable in
HDMI terminal (INPUT 5)
PC Nterminals (INPUT 6)
HDMI terminal (INPUT 4)
COMPO·
NENT
,------ INPUT 3terminals
(i) AUDIO
~=~I
@) @) 5I
~
DIGITAL
@AUDIO I
OUTPUT
VIDEO VIDEO Y
@)@)@)
LL Pa
@)@)@)
AUDIO AUDIO PR
@)@)@)
R R
VIDEO y
@)@)
LL Pa
A~ S~ ~~
@)@)@)
R
~
ry~
S-VIDEO
L..- AUDIO OUTPUT terminals
@- 11
Part names
,----------- Remote control sensor
J
--------OPC sensor*
..•. P0
1
WER SL~'LE_P _OP_C _
I 0--- OPC indicator**
SLEEP indicator**
------ POWER indicator**
()
,
III
••• 0·"
.--dJ
R!m
*OPC: Optical Picture Control (See page 26.)
**See page 16 for 1V status indicator.
POWER button
INPUT button
AC INPUT terminal
Channel buttons
(CHV//\)
Volume
buttons
(vOL-I+)~
f~====::: ~I== ==,~I====, ~Il
DIGI AL AUDIO OUTPUT
terminal
INPUT 1terminals
INPUT 2terminals
AUDIO terminals (INPUT
5)
Antenna/Cable in
HDMI terminal (INPUT 5)
PC Nterminals (INPUT 6)
HDMI terminal (INPUT 4)
COMPO·
NENT
,------ INPUT 3terminals
(i) AUDIO
~=~I
@) @) 5I
~
DIGITAL
@AUDIO I
OUTPUT
VIDEO VIDEO Y
@)@)@)
LL Pa
@)@)@)
AUDIO AUDIO PR
@)@)@)
R R
VIDEO y
@)@)
LL Pa
A~ S~ ~~
@)@)@)
R
~
ry~
S-VIDEO
L..- AUDIO OUTPUT terminals
@- 11

Part names
~
•When using the remote control unit, point it at the 1V
•••
5~H •••
•••
6-~ ••• ~t-17
-; INPUT FlASIiBACK ~
7 --+-----. .-,;...-- 18
i
, VOLGH t
8 ~ SURRO.UNOI IM.UT,-E ~ __ 19
9 --::-} -; i 20
~ FREEZE MENU ~
10 -----'-(-. e:--;,-"-- 21
t ~-~ ~
i I. >--:!:-' - 22
EXIT q9 TURN !
11 ----:,.....-. e----:-- 23
~~ 24
-_~ .... __ ~_~ ... ~_ ~ """1"5
~ . -,- FAii_
E
'..,.., :...;;.1_- 25
1, : , SLEEP AUDIO AV MOO€ CC :' i
I, T-- -,,- ----',' i,:'-' -- 26
~:' ;, ~
12 t:J
i -,. ~
~
1 TV POWER: Switch the 1V power on or enters
standby. (See page 16.)
2DISPLAY: Display the channel information.
3SOURCE POWER: Turns the power
of the external
equipment on and off.
4External
equipment operational buttons: Operate
the external equipment.
5 0 - 9: Set the channel. (See page 18.)
6 • (DOT): (See pages
18 and 49.)
7INPUT: Select a
lV input source. (lV, INPUT 1,
INPUT 2, INPUT 3, INPUT 4, INPUT 5, INPUT 6) (See
pages
30 and 31.)
8VOL +I
-: Set the volume. (See page 19.)
9SURROUND: Select Surround settings. (See page
19.)
10 FREEZE: Set the still image. Press again to return to
normal screen. (See page 47.)
11 EXIT: Turn off the menu screen.
12 SLEEP: Set the sleep timer. (See page 34.)
13 AUDIO: Selects the MTS/SAP or the audio mode
during multi-channel audio broadcasts. (See page 20.)
14 FUNCTION: Switches the remote control for lV,
CBUSAT, VCR, DVD and AUDIO operation. Indicator
lights up for the current mode. (See pages 47 to 50
for details.)
*To enter the code registration mode, you need to
press FUNCTION and DISPLAY at the same time.
15 LIGHT -li-: When pressed all buttons on the remote
control unit will light. The lighting will turn off if no
operations are performed within about 5seconds.
This button is used for performing operations
in low-
light situations.
16 VIEW MODE: Select the screen size. (See pages 35
and 36.)
17 ENT: Jumps to achannel after selecting with the 0-9
buttons.
18 FLASHBACK: Return to the previous channel or
external input mode. (See page 18.)
19 CHA/V: Select the channel. (See page 18.)
20 MUTE: Mute the sound. (See page 19.)
21 MENU: Display the menu screen.
22 J;./T / .... /~/ENTER: Select adesired item on the
screen.
23 RETURN: Return to the previous menu screen.
24 FAVORITE CH
A, B,
C, 0: Select 4preset favorite channels in 4
different categories. (See page 25 for details.)
While watching, you can toggle the selected channels
by pressing
A, B, Cand D.
25 FAVORITE: Set the favorite channels. (See page 25.)
26 CC: Display captions from aclosed-caption source.
(See page 39.)
27 AV MODE: Select an audio or video setting.
(When the input source is
lV, INPUT 1, 2 or 3:
STANDARD, MOVIE, GAME, USER, DYNAMIC (Fixed),
DYNAMIC. When the input source
is INPUT 4, 5 or 6:
STANDARD, MOVIE, GAME, PC, USER, DYNAMIC
(Fixed), DYNAMIC) (See page 38.)
16
-";",.-15
f
~
1
'---~',,-- 27
I
'j
1
\
. ~
,
~
14
't:'"~- ... ,".- -< ... -
t: .
•
r
1
i---
REG
.; ---
<-
-I
•
j
~
.,
._---
4
2
-~~~:::;-,
3--':-----.,
13 ------''---'
@- 12
Part names
~
•When using the remote control unit, point it at the 1V
•••
5~H •••
•••
6-~ ••• ~t-17
-; INPUT FlASIiBACK ~
7 --+-----. .-,;...-- 18
i
, VOLGH t
8 ~ SURRO.UNOI IM.UT,-E ~ __ 19
9 --::-} -; i 20
~ FREEZE MENU ~
10 -----'-(-. e:--;,-"-- 21
t ~-~ ~
i I. >--:!:-' - 22
EXIT q9 TURN !
11 ----:,.....-. e----:-- 23
~~ 24
-_~ .... __ ~_~ ... ~_ ~ """1"5
~ . -,- FAii_
E
'..,.., :...;;.1_- 25
1, : , SLEEP AUDIO AV MOO€ CC :' i
I, T-- -,,- ----',' i,:'-' -- 26
~:' ;, ~
12 t:J
i -,. ~
~
1 TV POWER: Switch the 1V power on or enters
standby. (See page 16.)
2DISPLAY: Display the channel information.
3SOURCE POWER: Turns the power
of the external
equipment on and off.
4External
equipment operational buttons: Operate
the external equipment.
5 0 - 9: Set the channel. (See page 18.)
6 • (DOT): (See pages
18 and 49.)
7INPUT: Select a
lV input source. (lV, INPUT 1,
INPUT 2, INPUT 3, INPUT 4, INPUT 5, INPUT 6) (See
pages
30 and 31.)
8VOL +I
-: Set the volume. (See page 19.)
9SURROUND: Select Surround settings. (See page
19.)
10 FREEZE: Set the still image. Press again to return to
normal screen. (See page 47.)
11 EXIT: Turn off the menu screen.
12 SLEEP: Set the sleep timer. (See page 34.)
13 AUDIO: Selects the MTS/SAP or the audio mode
during multi-channel audio broadcasts. (See page 20.)
14 FUNCTION: Switches the remote control for lV,
CBUSAT, VCR, DVD and AUDIO operation. Indicator
lights up for the current mode. (See pages 47 to 50
for details.)
*To enter the code registration mode, you need to
press FUNCTION and DISPLAY at the same time.
15 LIGHT -li-: When pressed all buttons on the remote
control unit will light. The lighting will turn off if no
operations are performed within about 5seconds.
This button is used for performing operations
in low-
light situations.
16 VIEW MODE: Select the screen size. (See pages 35
and 36.)
17 ENT: Jumps to achannel after selecting with the 0-9
buttons.
18 FLASHBACK: Return to the previous channel or
external input mode. (See page 18.)
19 CHA/V: Select the channel. (See page 18.)
20 MUTE: Mute the sound. (See page 19.)
21 MENU: Display the menu screen.
22 J;./T / .... /~/ENTER: Select adesired item on the
screen.
23 RETURN: Return to the previous menu screen.
24 FAVORITE CH
A, B,
C, 0: Select 4preset favorite channels in 4
different categories. (See page 25 for details.)
While watching, you can toggle the selected channels
by pressing
A, B, Cand D.
25 FAVORITE: Set the favorite channels. (See page 25.)
26 CC: Display captions from aclosed-caption source.
(See page 39.)
27 AV MODE: Select an audio or video setting.
(When the input source is
lV, INPUT 1, 2 or 3:
STANDARD, MOVIE, GAME, USER, DYNAMIC (Fixed),
DYNAMIC. When the input source
is INPUT 4, 5 or 6:
STANDARD, MOVIE, GAME, PC, USER, DYNAMIC
(Fixed), DYNAMIC) (See page 38.)
16
-";",.-15
f
~
1
'---~',,-- 27
I
'j
1
\
. ~
,
~
14
't:'"~- ... ,".- -< ... -
t: .
•
r
1
i---
REG
.; ---
<-
-I
•
j
~
.,
._---
4
2
-~~~:::;-,
3--':-----.,
13 ------''---'
@- 12

Preparation
• 0.
'.C:~l!ti~ris .. ~egardin9 ttl~~~~~t~9Pr1~~ol: Uijl~_
• Do not expose the remote control unit to shock. In addition, do not expose the remote
control unit to liquids, and do not place in an area with high humidity.
•
Do not install or place the remote control unit under direct sunlight. The heat may cause
deformation of the remote control unit.
•The remote control unit may not work properly
if the remote control sensor on the 1V is
under direct sunlight or strong lighting. In such cases, change the angle of the lighting or
the 1V, or operate the remote control unit closer to the remote control sensor.
Use the remote control unit by pointing it towards the remote control sensor on the
TV. Objects between the remote control unit and the remote control sensor may
prevent proper operation.
To enjoy aclearer picture, use
an outdoor antenna. The following is abrief explanation of the types of connections
that are used for acoaxial cable.
If your outdoor antenna uses a75-ohm coaxial cable with an F-type connector,
plug it into the antenna terminal at the rear of the
TV set.
1. A75-ohm system is generally around cable with F-type
connector that can easily be attached to aterminal
without tools (Commercially available).
F-type connector
I
----~m 75-ohm coaxial cable (round)
2. A 3OG-ohm system is aflat "twin-lead" cable that can be
attached to a75-ohm terminal through a300/75-ohm
adapter (Commercially available).
c=====~==>== 3OG-ohm twin-lead cable (flat)
~ F-type connector should be finger-
~ tightened only.
When connecting the
RF cable to the TV set, do not
tighten F-type connector with tools.
If tools are used, it may cause damage to your TV
set. (The breaking of internal circuit, etc.)
X
D~'""' F-type connector
_----- 17
~---- '¥ \"
"-
75-ohm coaxial cable
Connecting Antenna Cable
G) Cable without a CATV
converter
Home Antenna
terminal (75-ohm)
iiii
Ca
•b 'e;,,;TV .. Ie.a .. d-' .. " -------- ~ ~~\==<J
Coaxial cable
(commefclally available)
® VHF/UHF antenna
300-ohm twin-lead cable (1Iat)
Home Antenna
75-ohm coaxial cable (round) terminal (75-ohm)
---------~ ~~\==<J
CoaxIal cable
(commerCially available)
• Connect the antenna cable
to the TV using one of the
methods in the illustration
as shown (G), ®, @ or@).
3OOf75·ohm adapter
(commercially available)
To 1V antenna
terminal
300-ohm
twin-lead cable Combiner
\
(commerCially
available)
3OO-ohm twin-lead cable} I
~====~=-IN ouri-, ------~1Xl}
or
i:=:~ ==7S===oo==hm=,c=o.=xia===, c=lia~
VHF UHF
At><TENNA ANTENNA
@ Separate VHF/UHF
antenna
@ Combination VHF/
UHF antenna
@)- 13
Preparation
• 0.
'.C:~l!ti~ris .. ~egardin9 ttl~~~~~t~9Pr1~~ol: Uijl~_
• Do not expose the remote control unit to shock. In addition, do not expose the remote
control unit to liquids, and do not place in an area with high humidity.
•
Do not install or place the remote control unit under direct sunlight. The heat may cause
deformation of the remote control unit.
•The remote control unit may not work properly
if the remote control sensor on the 1V is
under direct sunlight or strong lighting. In such cases, change the angle of the lighting or
the 1V, or operate the remote control unit closer to the remote control sensor.
Use the remote control unit by pointing it towards the remote control sensor on the
TV. Objects between the remote control unit and the remote control sensor may
prevent proper operation.
To enjoy aclearer picture, use
an outdoor antenna. The following is abrief explanation of the types of connections
that are used for acoaxial cable.
If your outdoor antenna uses a75-ohm coaxial cable with an F-type connector,
plug it into the antenna terminal at the rear of the
TV set.
1. A75-ohm system is generally around cable with F-type
connector that can easily be attached to aterminal
without tools (Commercially available).
F-type connector
I
----~m 75-ohm coaxial cable (round)
2. A 3OG-ohm system is aflat "twin-lead" cable that can be
attached to a75-ohm terminal through a300/75-ohm
adapter (Commercially available).
c=====~==>== 3OG-ohm twin-lead cable (flat)
~ F-type connector should be finger-
~ tightened only.
When connecting the
RF cable to the TV set, do not
tighten F-type connector with tools.
If tools are used, it may cause damage to your TV
set. (The breaking of internal circuit, etc.)
X
D~'""' F-type connector
_----- 17
~---- '¥ \"
"-
75-ohm coaxial cable
Connecting Antenna Cable
G) Cable without a CATV
converter
Home Antenna
terminal (75-ohm)
iiii
Ca
•b 'e;,,;TV .. Ie.a .. d-' .. " -------- ~ ~~\==<J
Coaxial cable
(commefclally available)
® VHF/UHF antenna
300-ohm twin-lead cable (1Iat)
Home Antenna
75-ohm coaxial cable (round) terminal (75-ohm)
---------~ ~~\==<J
CoaxIal cable
(commerCially available)
• Connect the antenna cable
to the TV using one of the
methods in the illustration
as shown (G), ®, @ or@).
3OOf75·ohm adapter
(commercially available)
To 1V antenna
terminal
300-ohm
twin-lead cable Combiner
\
(commerCially
available)
3OO-ohm twin-lead cable} I
~====~=-IN ouri-, ------~1Xl}
or
i:=:~ ==7S===oo==hm=,c=o.=xia===, c=lia~
VHF UHF
At><TENNA ANTENNA
@ Separate VHF/UHF
antenna
@ Combination VHF/
UHF antenna
@)- 13

Preparation
~
VIDEO VIDEO Y
S-VIOEO
0-
When using composite cable (commercially
available).
VCR/Game console/
Camcorder
AVCR, game console, camcorder and other
audiovisual equipment can be conveniently connected
using the INPUT 1to 3terminals.
When using S-VIDEO cable (commercially
available).
You can use the INPUT 1, INPUT 2or INPUT 3
terminals when connecting to aBlu-ray disc player,
HD-DVD player, DVD player, aDigital TV STB (Air or
Cable) and other audiovisual equipment.
When using composite cable (commercially
available).
You can connect many types of external equipment to
your
TV like aBlu-ray disc player, HD-DVD player, DVD
player, VCR, Digital TV tuner, HDMI equipment, game
console or camcorder. To view external source images,
select the input source from INPUT on the remote
control unit or on the
TV. (See pages 30 and 31.)
Ii.nm
•To protect equipment, always turn off the TV before
connecting any external equipment.
•Please read the relevant operation manual (Blu-ray disc
player, etc.) carefully before making connections.
•
If your Blu-ray disc player offers achoice of output formats,
please select
nop for use with this TV.
COMPO·
NENT
VIDEO VIDEO II VIDEO ~y
@ IL IIL~ P,
L @"~I-----!~~I"o~
:@ !:J1A~ Pe
~!!.-R----l_---.J
COMPO·
NENT
VIDEO VIDEO
~
VIDEO Y
@@
,I,@ ,
P,
@
AUDIO
I AUDIO AUDIO
Pe
@@
RRR
Blu-ray disc player/HD-DVD player/
DVD player/Digital TV STB
AUDIO
R·AUDIQ-L
ANT/CABLE
External audio
devices
Optical fiber cable
(commercially available)
~
•The S-VIDEO terminal takes priority over the video
terminals. (INPUT 3only)
VCR/Game console/
Camcorder
·.·;Q~i~~rfjig~t.aIAudio .putput· ..
It is possible to output audio through the DIGITAL
AUDIO OUTPUT terminal. (See page 29 for details.)
PCM audio outputs from the terminal.
Component
video cable
(commercially
available)
Audio cable
(commercially available)
I
Y~ I
,.... .. lB
l
'@ p,~ lillI __
AUDIO @.......... '"
-... .. I@PR@I
etii ......... -'"
-' I
Blu-ray disc player/HD-
DVD player/ DVD player/
Digital TV STB
When using component cable. (INPUT 1 or 2)
@)- 14
Preparation
~
VIDEO VIDEO Y
S-VIOEO
0-
When using composite cable (commercially
available).
VCR/Game console/
Camcorder
AVCR, game console, camcorder and other
audiovisual equipment can be conveniently connected
using the INPUT 1to 3terminals.
When using S-VIDEO cable (commercially
available).
You can use the INPUT 1, INPUT 2or INPUT 3
terminals when connecting to aBlu-ray disc player,
HD-DVD player, DVD player, aDigital TV STB (Air or
Cable) and other audiovisual equipment.
When using composite cable (commercially
available).
You can connect many types of external equipment to
your
TV like aBlu-ray disc player, HD-DVD player, DVD
player, VCR, Digital TV tuner, HDMI equipment, game
console or camcorder. To view external source images,
select the input source from INPUT on the remote
control unit or on the
TV. (See pages 30 and 31.)
Ii.nm
•To protect equipment, always turn off the TV before
connecting any external equipment.
•Please read the relevant operation manual (Blu-ray disc
player, etc.) carefully before making connections.
•
If your Blu-ray disc player offers achoice of output formats,
please select
nop for use with this TV.
COMPO·
NENT
VIDEO VIDEO II VIDEO ~y
@ IL IIL~ P,
L @"~I-----!~~I"o~
:@ !:J1A~ Pe
~!!.-R----l_---.J
COMPO·
NENT
VIDEO VIDEO
~
VIDEO Y
@@
,I,@ ,
P,
@
AUDIO
I AUDIO AUDIO
Pe
@@
RRR
Blu-ray disc player/HD-DVD player/
DVD player/Digital TV STB
AUDIO
R·AUDIQ-L
ANT/CABLE
External audio
devices
Optical fiber cable
(commercially available)
~
•The S-VIDEO terminal takes priority over the video
terminals. (INPUT 3only)
VCR/Game console/
Camcorder
·.·;Q~i~~rfjig~t.aIAudio .putput· ..
It is possible to output audio through the DIGITAL
AUDIO OUTPUT terminal. (See page 29 for details.)
PCM audio outputs from the terminal.
Component
video cable
(commercially
available)
Audio cable
(commercially available)
I
Y~ I
,.... .. lB
l
'@ p,~ lillI __
AUDIO @.......... '"
-... .. I@PR@I
etii ......... -'"
-' I
Blu-ray disc player/HD-
DVD player/ DVD player/
Digital TV STB
When using component cable. (INPUT 1 or 2)
@)- 14

PC
Preparation
You can use the INPUT 4or INPUT 5terminal when connecting HOMI equipment.
Heml HOM! cable
~ d Olfi!~ __ (_co_m_l_ne_r_ci_al_ly_a_Va_ila_b_le_) -.lUiii~~~W.
~~;='iiiiiiiiiiii~
HOMI equipment
~
•When using an HDMI-DVI conversion cable, input the audio signal to AUDIO terminal of INPUT 5.
•When receiving an incompatible signal, such as 1080p, the message below appears without the image on the screen.
For an incompatible video signal: "An incompatible video signal has been received. Check the output device settings."
For an incompatible audio signal: "An incompatible audio signal has been received. Check the output device settings."
",9~pn~Qt~n~cr~c
When connecting to aPC with an analog RGB terminal. (INPUT 6)
RGB cable
i~ __ (_c_o_m_m_e_r_C_ia_IIY_a_Va_i_la_b_le_) __
I
@~<?----;:-:::-==::-:==--gQ~~iiiiiiiOW
o 3.5 mm stereo minijack
cable (commercially available)
When connecting to aPC with an HOMI terminal. (INPUT 4 or 5)
Heml HOMI cable
ID d Om~~ __ (c_o_m_m_e_rc_ia_lly_a_V_a_ila_b_le) __ t;;~WJltUJ,
~~
PC
~
•The HDMI terminals only support digital signal.
'PC,compatibility chart .'
.'. ~- .- .-. .,.
It is necessary to set the PC correctly to display XGA and WXGA signal. Refer to page 38 to set PC input signals,
PC Resolution Horizontal Frequency Vertical Frequency VESA Standard
720 x 400 31.5 kHz 70 Hz
--
VGA
31.5 kHz
60 Hz 0
640 x 480 37.9 kHz 72 Hz
0
37.5 kHz
75 Hz 0
35.1 kHz 56 Hz
0
SVGA
800 x 600
37.9 kHz 60 Hz
0
PC 48.1 kHz 72 Hz
0
46.9 kHz 75 Hz
0
48.4 kHz
60 Hz 0
XGA 1024 x 768 56.5 kHz
70 Hz
0
600 kHz 75 Hz
0
WXGA
1360 x 768 47.7 kHz 60 Hz
0
DOC is a registered trademark of Video Electronics Standards Association.
Power Management is a registered trademark of Sun Microsystems, Inc.
VGA and XGA are registered trademarks of International Business Machines Corp.
@)- 15
PC
Preparation
You can use the INPUT 4or INPUT 5terminal when connecting HOMI equipment.
Heml HOM! cable
~ d Olfi!~ __ (_co_m_l_ne_r_ci_al_ly_a_Va_ila_b_le_) -.lUiii~~~W.
~~;='iiiiiiiiiiii~
HOMI equipment
~
•When using an HDMI-DVI conversion cable, input the audio signal to AUDIO terminal of INPUT 5.
•When receiving an incompatible signal, such as 1080p, the message below appears without the image on the screen.
For an incompatible video signal: "An incompatible video signal has been received. Check the output device settings."
For an incompatible audio signal: "An incompatible audio signal has been received. Check the output device settings."
",9~pn~Qt~n~cr~c
When connecting to aPC with an analog RGB terminal. (INPUT 6)
RGB cable
i~ __ (_c_o_m_m_e_r_C_ia_IIY_a_Va_i_la_b_le_) __
I
@~<?----;:-:::-==::-:==--gQ~~iiiiiiiOW
o 3.5 mm stereo minijack
cable (commercially available)
When connecting to aPC with an HOMI terminal. (INPUT 4 or 5)
Heml HOMI cable
ID d Om~~ __ (c_o_m_m_e_rc_ia_lly_a_V_a_ila_b_le) __ t;;~WJltUJ,
~~
PC
~
•The HDMI terminals only support digital signal.
'PC,compatibility chart .'
.'. ~- .- .-. .,.
It is necessary to set the PC correctly to display XGA and WXGA signal. Refer to page 38 to set PC input signals,
PC Resolution Horizontal Frequency Vertical Frequency VESA Standard
720 x 400 31.5 kHz 70 Hz
--
VGA
31.5 kHz
60 Hz 0
640 x 480 37.9 kHz 72 Hz
0
37.5 kHz
75 Hz 0
35.1 kHz 56 Hz
0
SVGA
800 x 600
37.9 kHz 60 Hz
0
PC 48.1 kHz 72 Hz
0
46.9 kHz 75 Hz
0
48.4 kHz
60 Hz 0
XGA 1024 x 768 56.5 kHz
70 Hz
0
600 kHz 75 Hz
0
WXGA
1360 x 768 47.7 kHz 60 Hz
0
DOC is a registered trademark of Video Electronics Standards Association.
Power Management is a registered trademark of Sun Microsystems, Inc.
VGA and XGA are registered trademarks of International Business Machines Corp.
@)- 15

Watching TV
Simple operations for watching a lV program
c:::::::::J c:::::::::J
01
- VOL +vCH A. INPUT
POWER _
POWER
IJ
POWER SLEEP
Of'C
0 0 000
Press POWER on the lV, or TV POWER on the
remote control unit.
•POWER indicator (Green): The TV is on. (After afew
seconds, a
window appears with sound.)
~
•The initial setup starts when the TV powers on for the first
time. If the TV has been turned on before, the
EZ Setup will
not be invoked. See page
23 for performing EZ Setup from
the Setup menu.
_I_---J~-
Press POWER on the lV, or TV POWER on the
remote control unit.
•The TV enters standby and the image on the screen
disappears.
•The POWER indicator on the TV turns off.
POWER '- ope Indicator
indicator
SLEEP indicator
~
•If you are not going to use this TV for along period of time,
be sure to remove the AC cord from the AC outlet.
•Weak electric
power is still consumed even when the TV is
turned off.
TV POWER (On/Standby)
TV status indicator (POWER)
"Off" is selected in OPC setting
•See page
26 for details.
TV status indicator (Ope)
"On" or "On: Display" is selected in OPC setting Lighting (Green)
Lights off
Lighting (Green)
Lights off
ON
Standby
(ViEW"\
~
AUDIO
o
FUNCTION
o
LIGHT
@)
8
o
8 G
REC
o0
8 8
TV TV VCR
(J CB~SAT D~D
SOURCE
88
TV status indicator (SLEEP)
"Off" is selected in SLEEP setting Lights off
"30", "60", "90"
or "120" is selected in SLEEP setting Lighting (Red)
•See page
34 for details.
@- 16
Watching TV
Simple operations for watching a lV program
c:::::::::J c:::::::::J
01
- VOL +vCH A. INPUT
POWER _
POWER
IJ
POWER SLEEP
Of'C
0 0 000
Press POWER on the lV, or TV POWER on the
remote control unit.
•POWER indicator (Green): The TV is on. (After afew
seconds, a
window appears with sound.)
~
•The initial setup starts when the TV powers on for the first
time. If the TV has been turned on before, the
EZ Setup will
not be invoked. See page
23 for performing EZ Setup from
the Setup menu.
_I_---J~-
Press POWER on the lV, or TV POWER on the
remote control unit.
•The TV enters standby and the image on the screen
disappears.
•The POWER indicator on the TV turns off.
POWER '- ope Indicator
indicator
SLEEP indicator
~
•If you are not going to use this TV for along period of time,
be sure to remove the AC cord from the AC outlet.
•Weak electric
power is still consumed even when the TV is
turned off.
TV POWER (On/Standby)
TV status indicator (POWER)
"Off" is selected in OPC setting
•See page
26 for details.
TV status indicator (Ope)
"On" or "On: Display" is selected in OPC setting Lighting (Green)
Lights off
Lighting (Green)
Lights off
ON
Standby
(ViEW"\
~
AUDIO
o
FUNCTION
o
LIGHT
@)
8
o
8 G
REC
o0
8 8
TV TV VCR
(J CB~SAT D~D
SOURCE
88
TV status indicator (SLEEP)
"Off" is selected in SLEEP setting Lights off
"30", "60", "90"
or "120" is selected in SLEEP setting Lighting (Red)
•See page
34 for details.
@- 16

Watching TV
When you turn on the TV for the first time, it will automatically memorize the broadcasting channels where you live.
Perform the following steps before you press TV POWER on the remote control unit.
1. Insert the batteries into the remote control unit. (See page 9.)
2. Connect the antenna cable to the TV. (See page 13.)
3. Plug in the AC cord to the AC outlet. (See page 8.)
EXIT e-----) RETURN
O~O
Press .... /~ to select "Air" or "Cable".
Press ENTER to enter the setting.
Example
When "Cable" is selected in Antenna
setting:
Press Ji../~ to select "Analog &Digital Search
Start" to search both analog and digital
broadcasts or "Analog Search Start" to search
only analog broadcasts, and then press
ENTER.
When "Air" is selected
in Antenna setting:
Press .... /~ to select "Start", and then press
ENTER.
•The Channel search will start automatically.
To exit the Channel search screen, select "Cancel",
and then press ENTER.
Example
~
Channel search
Channel auto search makes the TV look for all
channels viewable in the set area.
FREEZE MENU
O~O
8e8
Antenna setting
Make sure what kind of connection is made with your
TV when selecting "Air" or "Cable".
Language setting
Select from among 3languages: English, French and
Spanish.
Press
JiJ~ to select the desired language
listed on the screen, and then press ENTER.
•
Air ANALOG
~
AudiO MONO
ItaD
• If no channel is found, confirm the type of connection made
with your
TV and try EZ Setup again. (See page 23)
@-17
Watching TV
When you turn on the TV for the first time, it will automatically memorize the broadcasting channels where you live.
Perform the following steps before you press TV POWER on the remote control unit.
1. Insert the batteries into the remote control unit. (See page 9.)
2. Connect the antenna cable to the TV. (See page 13.)
3. Plug in the AC cord to the AC outlet. (See page 8.)
EXIT e-----) RETURN
O~O
Press .... /~ to select "Air" or "Cable".
Press ENTER to enter the setting.
Example
When "Cable" is selected in Antenna
setting:
Press Ji../~ to select "Analog &Digital Search
Start" to search both analog and digital
broadcasts or "Analog Search Start" to search
only analog broadcasts, and then press
ENTER.
When "Air" is selected
in Antenna setting:
Press .... /~ to select "Start", and then press
ENTER.
•The Channel search will start automatically.
To exit the Channel search screen, select "Cancel",
and then press ENTER.
Example
~
Channel search
Channel auto search makes the TV look for all
channels viewable in the set area.
FREEZE MENU
O~O
8e8
Antenna setting
Make sure what kind of connection is made with your
TV when selecting "Air" or "Cable".
Language setting
Select from among 3languages: English, French and
Spanish.
Press
JiJ~ to select the desired language
listed on the screen, and then press ENTER.
•
Air ANALOG
~
AudiO MONO
ItaD
• If no channel is found, confirm the type of connection made
with your
TV and try EZ Setup again. (See page 23)
@-17

Watching TV
Method 1
Using CH A/Von the remote control unit or on the
N.
Method 2
CD Press FLASHBACK to switch to the previously
tuned channel.
®Press FLASHBACK again to switch back to the
currently tuned channel.
~
•FLASHBACK will not work if no channel has been
changed after the 1V is turned on.
Method 3
Using remote control buttons 0-9, • (DOT) to select
channels for VHF/UHF/CAN/DIGITAL.
To select a3-digit channel number
(e. g., Channel 115):
To select a 1
or 2-digit channel number
(e. g., Channel 5):
~
•When selecting a1-digit channel number, it is not
necessary to press 0before the number.
•When you enter 0-9 only, channel selection will be made if
there is no operation within afew seconds.
Press 5~ENT
-~-
POWER
®
®
®
€V
®
@
@@J)
INPUT FLASHBACK
00
TV TV VCR AUDIO
goo
0
</Ie~ CBl/SAT DVD
FUNCTION
pO 0 0 °
SOURCE
LIGHT
S8
@)
B
CE)
8
REC
C!)
0 0
8
(3 @ID
MODE
- VOL +v CH AINPUT
You can change channels in several ways.
VOL CH
SURROUNo(J. fJ ./;; .•• ~ MUTE
°- (jJ °Press 1
~ 1 ~5~ENT
FREEZE MENU
0c::::I:::::>0
8@8
EXIT e-----') RETURN
O~O
-FAVORITE CH -
0®@@
AQuas
To select a4-digit channel number
(e. g., Channel 22.1):
Press 2 ~2~ • (DOT) ~ 1 ~ENT
-~-~-~-~-
~
•When you enter 0-9 only, channel selection will be made if
there is no operation within afew seconds.
• If you push "0" by itself, nothing will happen.
•Complete the above steps within afew seconds.
•When you enter
0-9 and • (DOT), channel selection will be
made if there
is no operation within afew seconds.
@>- 18
Watching TV
Method 1
Using CH A/Von the remote control unit or on the
N.
Method 2
CD Press FLASHBACK to switch to the previously
tuned channel.
®Press FLASHBACK again to switch back to the
currently tuned channel.
~
•FLASHBACK will not work if no channel has been
changed after the 1V is turned on.
Method 3
Using remote control buttons 0-9, • (DOT) to select
channels for VHF/UHF/CAN/DIGITAL.
To select a3-digit channel number
(e. g., Channel 115):
To select a 1
or 2-digit channel number
(e. g., Channel 5):
~
•When selecting a1-digit channel number, it is not
necessary to press 0before the number.
•When you enter 0-9 only, channel selection will be made if
there is no operation within afew seconds.
Press 5~ENT
-~-
POWER
®
®
®
€V
®
@
@@J)
INPUT FLASHBACK
00
TV TV VCR AUDIO
goo
0
</Ie~ CBl/SAT DVD
FUNCTION
pO 0 0 °
SOURCE
LIGHT
S8
@)
B
CE)
8
REC
C!)
0 0
8
(3 @ID
MODE
- VOL +v CH AINPUT
You can change channels in several ways.
VOL CH
SURROUNo(J. fJ ./;; .•• ~ MUTE
°- (jJ °Press 1
~ 1 ~5~ENT
FREEZE MENU
0c::::I:::::>0
8@8
EXIT e-----') RETURN
O~O
-FAVORITE CH -
0®@@
AQuas
To select a4-digit channel number
(e. g., Channel 22.1):
Press 2 ~2~ • (DOT) ~ 1 ~ENT
-~-~-~-~-
~
•When you enter 0-9 only, channel selection will be made if
there is no operation within afew seconds.
• If you push "0" by itself, nothing will happen.
•Complete the above steps within afew seconds.
•When you enter
0-9 and • (DOT), channel selection will be
made if there
is no operation within afew seconds.
@>- 18