Sharp PN-S655 User manual

PN-S655
ENGLISH DEUTSCH FRANÇAIS ESPAÑOL 汉语
РУССКИЙ
LCD MONITOR
LCD FARBMONITOR
MONITEUR LCD
MONITOR LCD
ЖК МОНИТОР
液晶显示器
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
使用说明书
ENGLISH ...... E1
DEUTSCH .....D1
FRANÇAIS .... F1
ESPAÑOL .... S1
РУССКИЙ.....Р1
汉语 ............... C1

Authorised representative responsible for the European Union Community Market
Autorisierter Repräsentant in der Europäischen Union
Représentant autorisé pour le marché de la communauté européenne
Representante autorizado responsable del mercado comunitario de la Unión Europea
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg
IMPORTANT:
To aid reporting in case of loss or theft, please record the
product’s model and serial numbers in the space provided.
The numbers are located in the rear of the product.
Model No.:
Serial No.:
U.S.A. ONLY
FOR CUSTOMERS IN U.K.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW : Earth
BLUE : Neutral
BROWN : Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
•ThewirewhichiscolouredGREEN-AND-YELLOWmustbeconnectedtotheterminalintheplugwhichismarkedbythe
letter Eor by the safety earth or coloured green or green-and-yellow.
•ThewirewhichiscolouredBLUEmustbeconnectedtotheterminalwhichismarkedwiththeletterNor coloured black.
•ThewirewhichiscolouredBROWNmustbeconnectedtotheterminalwhichismarkedwiththeletterLor coloured red.
Ensurethatyourequipmentisconnectedcorrectly.Ifyouareinanydoubtconsultaqualiedelectrician.
“WARNING: THIS APPARATUS MUST BE EARTHED.”

ENGLISH
1E
IMPORTANT INFORMATION
PN-S655
LCD MONITOR
ENGLISH
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER.
NOUSER-SERVICEABLEPARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Thelightningashwitharrowheadsymbol,within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
beofsufcientmagnitudetoconstituteariskof
electric shock to persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
CAUTION: The AC outlet shall be installed near the equipment and shall be easily accessible.
CAUTION: Use the supplied power cord as it is.
Thisproductutilizesuorescenttubescontainingasmallamountofmercury.
Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling
information, please contact your local authorities.

2
E
IMPORTANT INFORMATION (Continued)
WARNING:
FCCRegulationsstatethatanyunauthorizedchangesormodicationstothisequipmentnotexpresslyapprovedbythe
manufacturer could void the user’s authority to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Thisproductutilizestin-leadsolder,anduorescentlampcontainingasmallamountofmercury.Disposalof
these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance:
www.eiae.org,thelamprecyclingorganization:www.lamprecycle.orgorSharpat1-800-BE-SHARP
(For U.S.A. Only)
U.S.A. ONLY
A. Information on Disposal for Users (private households)
1. In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dustbin!
Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper
treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the EU states may return their used electrical and
electronic equipment to designated collection facilities free of charge*. In some countries* your local retailer may also take
back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand
according to local requirements.
Bydisposingofthisproductcorrectlyyouwillhelpensurethatthewasteundergoesthenecessarytreatment,recoveryand
recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due
to inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t
purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and you want to discard it:
Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the
costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection
facilities.
For Spain: Please contact the established collection system or your local authority for take-back of your used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
Attention: Your product is marked with this symbol. It means that used electrical and electronic products
should not be mixed with general household waste. There is a separate collection system for these products.

ENGLISH
3E
DEAR SHARP CUSTOMER
Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your
product, please read the Safety Precautions carefully before using this product.
SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can
resultinelectricshockand/orre.Inordertopreventpotentialdanger,pleaseobservethefollowinginstructionswheninstalling,
operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the
following precautions carefully before using the product.
1. Read instructions — All operating instructions must be read and understood before the product is operated.
2. Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future
reference.
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
4. Follow instructions — All operating instructions must be followed.
5. Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do
not use liquid cleaners or aerosol cleaners.
6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result
in accidents.
 7. Waterandmoisture—Donotusetheproductnearwater.Donotinstalltheproductinaplacewherewatermaysplashonto
it.Becarefulofequipmentwhichdrainswatersuchasanair-conditioner.
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
  Donotcoverorblocktheseventsandopeningssinceinsufcientventilationcancauseoverheatingand/orshortenthelife
of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings.
Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from
resting on them.
10. The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact.BecarefulnottobeinjuredbybrokenglasspiecesincasetheLCDpanelbreaks.
11. Overloading—DonotoverloadACoutletsorextensioncords.Overloadingcancausereorelectricshock.
12. Enteringofobjectsandliquids—Neverinsertanobjectintotheproductthroughventsoropenings.Highvoltageowsin
the product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other
dangerousconditions.Requestaqualiedservicepersontoperformservicing.
IMPORTANT INFORMATION (Continued)
The battery supplied with this product contains traces of Lead.
For EU:
The crossed-out wheeled bin implies that used batteries should not be put to the general household
waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in
accordance with legislation. Please contact your local authority for details on the collection and recycling
schemes.
For Switzerland:
The used battery is to be returned to the selling point.
For other non-EU countries:
Please contact your local authority for correct method of disposal of the used battery.

4
E
SAFETY PRECAUTIONS (Continued)
14. Repair—Ifanyofthefollowingconditionsoccurs,unplugthepowercordfromtheACoutlet,andrequestaqualiedservice
person to perform repairs.
a. Whenthepowercordorplugisdamaged.
b. Whenaliquidwasspilledontheproductorwhenobjectshavefallenintotheproduct.
c. Whentheproducthasbeenexposedtorainorwater.
d. Whentheproductdoesnotoperateproperlyasdescribedintheoperatinginstructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls
notdescribedintheinstructionscancausedamage,whichoftenrequiresextensiveadjustmentworkbyaqualied
technician.
  e. Whentheproducthasbeendroppedordamaged.
  f. Whentheproductdisplaysanabnormalcondition.Anynoticeableabnormalityintheproductindicatesthattheproduct
needs servicing.
15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement
partsspeciedbythemanufacturer,orthosewiththesamecharacteristicsandperformanceastheoriginalparts.Useof
unauthorizedpartscanresultinre,electricshockand/orotherdanger.
16. Safety checks — Upon completion of service or repair work, request the service technician to
perform safety checks to ensure that the product is in proper operating condition.
17. Wallmounting—Whenmountingtheproductonawall,besuretoinstalltheproductaccordingtothemethod
recommended by the manufacturer.
18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products(includingampliers).
19. Batteries—Incorrectuseofbatteriesmaycausethebatteriestoburstorignite.Aleakybatterymaycorrodetheequipment,
dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:
  •Usethespeciedbatteriesonly.
  •Installthebatterieswithdueattentiontotheplus(+)andminus(-)sidesofthebatteriesaccordingtotheinstructionsinthe
compartment.
  •Donotmixoldandnewbatteries.
  •Donotmixbatteriesofdifferenttypes.Voltagespecicationsofbatteriesofthesameshapemayvary.
  •Replaceanexhaustedbatterywithanewonepromptly.
  •Ifyouwillnotusetheremotecontrolforalongtime,removethebatteries.
  •Ifleakedbatteryuidgetsonyourskinorclothing,rinseimmediatelyandthoroughly.Ifitgetsintoyoureye,batheyour
eyewellratherthanrubbingandseekmedicaltreatmentimmediately.Leakedbatteryuidthatgetsintoyoureyeoryour
clothing may cause a skin irritation or damage your eye.
20. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and
missile launch control in a weapon system.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate counter measures.

ENGLISH
5E
- The TFT color LCD panel used in this monitor is made with
the application of high precision technology. However, there
may be minute points on the screen where pixels never light
or are permanently lit. Also, if the screen is viewed from
an acute angle there may be uneven colors or brightness.
Please note that these are not malfunctions but common
phenomena of LCDs and will not affect the performance of
the monitor.
- Do not display a still picture for a long period, as this could
cause a residual image.
- Never rub or tap the monitor with hard objects.
- Please understand that SHARP CORPORATION bears no
responsibility for errors made during use by the customer or
a third party, nor for any other malfunctions or damage to this
product arising during use, except where indemnity liability is
recognized under law.
- This monitor and its accessories may be upgraded without
advance notice.
- Do not use the monitor where there is a lot of dust, where
humidity is high, or where the monitor may come into contact
withoilorsteam,asthiscouldleadtore.
- Ensure that the monitor does not come into contact with
waterorotheruids.Ensurethatnoobjectssuchaspaper
clipsorpinsenterthemonitorasthiscouldleadtoreor
electric shock.
- Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong
shocks or to strongly vibrate. Causing the monitor to fall or
topple over may damage it.
- Do not use the monitor near heating equipment or in places
where there is likelihood of high temperature, as this may
leadtogenerationofexcessiveheatandoutbreakofre.
The Power Cord
- Do not damage the power cord nor place heavy objects on
it, stretch it or over bend it. Also, do not add extension cords.
Damagetothecordmayresultinreorelectricshock.
- Use only the power cord supplied with the monitor.
- Insert the power plug directly into the AC outlet.
Addinganextensioncordmayleadtoreasaresultof
overheating.
- Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
- Unplug the power cord if it is not used for a long time.
- Do not attempt to repair the power cord if it is broken
or malfunctioning. Refer the servicing to the service
representative.
Initialization
- This monitor can remember e-mail addresses and other data.
Beforetransferringordisposingofthismonitor,initializeall
settings by executing ALL RESET 1. (See Operation guide.)
Executing ALL RESET 2 will not reset e-mail addresses and
similar data.
Manual Scope
-Microsoft,WindowsandInternetExplorerareregistered
trademarks of Microsoft Corporation.
- HDMI, the HDMI LogoandHigh-DenitionMultimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
- Adobe, Acrobat, and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
-ThisproductcomeswithRICOHBitmapFontsproducedand
sold by RICOH COMPANY, LTD.
- All other brand and product names are trademarks or
registered trademarks of their respective holders.
- Language of OSD menu used in this manual is English by
way of example.
- Illustrations in this manual may not exactly represent the
actual product or display.
Fluorescent Tubes
● Theuorescenttubesinthisproducthavealimitedlifetime.
● Becauseofthepropertyofuorescenttubes,thescreen
mayashduringtheinitialperiodofuse.Ifthishappens,
please turn off the main power switch of the monitor and
turnonagainafteratleast5secondstoconrmoperation.
TIPS AND SAFETY INSTRUCTIONS

6
E
Contents
IMPORTANT INFORMATION............................................1
DEAR SHARP CUSTOMER..............................................3
SAFETY PRECAUTIONS..................................................3
TIPS AND SAFETY INSTRUCTIONS ...............................5
Supplied Accessories......................................................7
Part Names .......................................................................7
How to Install the Monitor...............................................9
Mounting precautions...................................................9
Connecting Peripheral Equipment...............................10
Connection with a PC.................................................10
Connection with AV equipment ..................................10
Other terminals...........................................................11
Connecting external speakers....................................11
Connecting multiple monitors.....................................11
Connecting the Power Cord .........................................12
Preparing the Remote Control Unit..............................12
Installing the batteries ................................................12
Remote control operation range.................................12
Removing the Temporary Stand...................................13
Turning Power On/Off....................................................14
Turning on the main power.........................................14
Turning power on/off ..................................................14
Disabling power on/off operations..............................14
Troubleshooting.............................................................15
Specications ................................................................16
This manual contains instructions regarding connection and installation.
For instructions regarding operation, settings, and similar details, refer to the Operation Guide (PNS655_guide_English.pdf)
in the “manual” folder on the included CD-ROM.
Adobe Reader is required in order to view the Operation Guide.

ENGLISH
7E
Supplied Accessories
If any component should be missing, please contact your dealer.
 Liquid Crystal Display: 1
 Remote control unit: 1
 Power cord: 1
 R-6 battery (“AA” size): 2
 CD-ROM(UtilityDiskforWindows):1
 Operation manual: 1
 Stand hole protection cover: 2
* Sharp Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
Part Names
nFront view
1
2 543
6
1. LCD panel
2. Remote control sensor (See page 12.)
3. Power LED (See page 14.)
4. Power switch (See page 14.)
5. Input switch (See Operation guide.)
6. Temporary Stand (See page 13.)
TIPS
• Useapointedobjectsuchasapentiptopressthe
switches at the front of the monitor.

8
E
Part Names
nRear view
19
18
20
1 4 8 9 10 11
5
6 12 1314 15
7
2 3
16
17
1. PC/AV output terminal (DVI-D) (See page 11.)
2. PC1 input terminal (DVI-D) (See page 10.)
AV1 input terminal (DVI-D) (See page 10.)
3. PC2 input terminal (HDMI) (See page 10.)
AV2 input terminal (HDMI) (See page 10.)
4. PC3 input terminal (Mini D-sub 15 pin) (See page 10.)
5. PC4 input terminals (BNC) (See page 10.)
6. AV3 input terminals (BNC) (See page 10.)
7. AV5 input terminal (BNC) (See page 10.)
8. AV4 input terminal (S) (See page 10.)
9. LAN terminal (See page 11.)
10. RS-232C output terminal (D-sub 9 pin) (See page 11.)
11. RS-232C input terminal (D-sub 9 pin) (See page 11.)
12. PC/AV audio output terminals (See page 11.)
13. AV audio input terminals (See page 10.)
14. PC audio input terminal (See page 10.)
15. External speaker terminals (See page 11.)
16. Main power switch (See page 14.)
17. AC input terminal (See page 12.)
18. Handles
19. Vents
20. Hooks
nRemote control unit
1
2
3
4
5
6
9
8
7
1. Signal transmitter
2. POWER button (See page 14.)
3. MUTE button (See Operation guide.)
4. VOL +/- buttons (See Operation guide.)
BRIGHT +/- buttons (See Operation guide.)
Cursor control ( / / / ) buttons
5. DISPLAY button (See Operation guide.)
6. MODE button (See Operation guide.)
7. INPUT button (See Operation guide.)
8. MENU button (See Operation guide.)
9. SIZE button (See Operation guide.)

ENGLISH
9E
How to Install the Monitor
Mounting precautions
• Sincethemonitorisheavy,consultyourdealerbefore
installing, removing or moving the monitor.
• Wheninstalling,removingormovingthemonitor,ensure
that this is carried out by at least 2 people.
• Whenmovingthemonitor,besuretoholditwiththe
handles both on the rear and the unit bottom. Do not hold
the LCD panel. This may cause product damage, failure, or
injury.
• Installthemonitorwiththesurfaceperpendiculartoalevel
surface. If necessary, the monitor may be tilted up to 20
degrees.
• Mountingthemonitoronthewallrequiresspecialexpertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this
work yourself. Our company will bear no responsibility
for accidents or injuries caused by improper mounting or
mishandling.
• Thismonitorshouldbeusedatanambienttemperature
between 32°F (0°C) and 104°F (40°C). Provide
enough space around the monitor to prevent heat from
accumulating inside.
U
n
i
t:
i
nc
h
[
cm
]
1-3/8 [3.5]
1-
15/16
[5]
1-
15/16
[5]
1-15/16 [5]
11-13/16 [30]
• Ifitisdifficulttoprovidethismuchspaceforanyreason
such as the installation of the monitor inside a housing, or if
the ambient temperature may be outside of the range of 32
°F (0°C) to 104°F (40°C), install a fan in the housing or take
other measures to keep the ambient temperature within the
required range.
• Donotblockanyventilationopenings.Ifthetemperature
inside the monitor rises, this could lead to a malfunction.
• Aftermounting,itisrecommendedtotakesomemeasures
to prevent the monitor from falling down. Secure the
monitor by fastening the hooks at the top of the monitor to a
wall or a pillar with strong cord and brackets (not included).
• Donotplacethemonitoronadevicewhichgeneratesheat.
• Thismonitorisxedtothetemporarystandwhenshipped
from the factory. Please note that this stand is for temporary
use only until the monitor is properly mounted.
• Besuretouseastandorawall-mountbracketdesignedor
designated for mounting the monitor.
• Thismonitorisdesignedtobeinstalledonaconcretewall
or pillar. Reinforced work might be necessary for some
materials such as plaster / thin plastic board / wood before
starting installation.
This monitor and bracket must be installed on a wall which
can endure at least 4 times or more the weight of the
monitor. Install by the most suitable method for the material
and the structure.

10
E
Connecting Peripheral Equipment
Caution
• Besuretoturnoffthemainpowerswitchanddisconnect
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the
equipment to be connected.
• Becarefulnottomixuptheinputterminalwiththeoutput
terminal when connecting cables. Mixing up the input and
output terminals may cause malfunctions and the other
problems.
Connection with a PC
Video input
PC1 input terminal PC2 input terminal
HV
RGB
PC3 input terminal PC4 input terminals
Audio input
PC audio input terminal
• Useacommerciallyavailablesignalcable(DVI-D24pin)
for the PC1 input terminal. Set DVI SELECT of INPUT
SELECT on the OPTION menu to PC1 DVI-D when using
the PC1 input terminal. (See Operation guide.)
• UseacommerciallyavailableHDMIcable(conformingto
the HDMI standard) for the PC2 input terminal. Set HDMI
SELECT of INPUT SELECT on the OPTION menu to PC2
HDMI when using the PC2 input terminal. In addition,
select the audio input terminal to be used in HDMI AUDIO
SELECT of INPUT SELECT on the OPTION menu. (See
Operationguide.)WhenDIGITALisselected,connectionto
the PC audio input terminal is unnecessary.
• Useacommerciallyavailablesignalcable(MiniD-sub
15 pin) for the PC3 input terminal.
• Useacommerciallyavailablesignalcable(BNC)forthe
PC4inputterminals.SetBNCSELECTofINPUTSELECT
ontheOPTIONmenutoPC4RGBwhenusingthePC4
input terminals. (See Operation guide.)
• Useacommerciallyavailableaudiocable(ministereojack)
for the PC audio input terminal. Use an audio cable without
resistance.
TIPS
• Imagesmaynotbedisplayedproperlydependingonthe
computer (graphics board) to be connected.
• Ascreenwith1920x1080resolutionmaynotbedisplayed
correctly on PC4. In this case, check the settings of your
computer (graphics board) to verify that input signals
conformtospecicationsofthismonitor.(Seepage17.)
• IfthereisacheckboxtodisableEDIDindisplaycontrol
panel, check it when using PC4.
• UsetheautomaticscreenadjustmentwhenaPCscreenis
displayedforthersttimeusingPC3orPC4,orwhenthe
setting of the PC is changed. (See Operation guide.)
The screen is adjusted automatically when SELF ADJUST
in the OPTION menu is set to ON. (See Operation guide.)
Connection with AV equipment
Video input
Cr/Pr Y Cb/Pb
AV1 input
terminal AV2 input terminal AV3 input terminals
AV4 input terminal AV5 input terminal
Audio input
AV audio input terminals
• Useacommerciallyavailablesignalcable(DVI-D24pin)
for the AV1 input terminal. Set DVI SELECT of INPUT
SELECT on the OPTION menu to AV1 DVI-D when using
the AV1 input terminal. (See Operation guide.)
• UseacommerciallyavailableHDMIcable(conformingto
the HDMI standard) for the AV2 input terminal. Set HDMI
SELECT of INPUT SELECT on the OPTION menu to
AV2 HDMI when using the AV2 input terminal. In addition,
select the audio input terminal to be used in HDMI AUDIO
SELECT of INPUT SELECT on the OPTION menu. (See
Operationguide.)WhenDIGITALisselected,connectionto
the AV audio input terminal is unnecessary.
• Useacommerciallyavailablecomponentcable(BNC)
fortheAV3inputterminals.SetBNCSELECTofINPUT
SELECT on the OPTION menu to AV3 COMPONENT when
using the AV3 input terminals. (See Operation guide.)
• UseacommerciallyavailableS-videocablefortheAV4
input terminal.
• Useacommerciallyavailablevideocable(BNC)forthe
AV5 input terminal.
• Useacommerciallyavailableaudiocable(RCA)fortheAV
audio input terminals.
• TheAV1/AV2inputterminalsarecompatiblewiththevideo
signals below:
1920 x 1080 p @ 50/59.94/60 Hz
1920 x 1080 i @ 50/59.94/60 Hz
1280 x 720 p @ 50/59.94/60 Hz
720 x 576 p @ 50 Hz
720 x 480 p @ 59.94/60 Hz
640 x 480 p @ 59.94/60 Hz
• TheAV2inputterminalisalsocompatiblewiththevideo
signals below:
1920 x 1080p @ 24Hz
720(1440) x 576i @ 50Hz
720(1440) x 480i @ 59.94/60Hz
• TheAV3inputterminalsarecompatiblewiththevideo
signals below:
1080p @50/60Hz, 1080i @50/60Hz, 720p @50/60Hz,
576p @50Hz, 576i @50Hz, 480p @60Hz, 480i @60Hz

ENGLISH
11 E
Connecting Peripheral Equipment
Other terminals
PC/AV audio output terminals
• AudiofromtheequipmentconnectedtotheAVaudioinput
terminals or PC audio input terminal is output. Connect to
the audio input terminals of the connected equipment using
a commercially available audio cable (RCA).
• Theaudiooutputvariesdependingontheinputmode
selection. (See Operation guide.)
• Thevolumelevelcanbeadjustedusingthevolume
adjustment. (See Operation guide.)
• SelectingFIXEDof“AUDIOOUTPUT”fromtheOPTION
menuxesthevolumeofsoundoutputfromtheaudio
output terminals. (See Operation guide.)
• AudiosignalsoutputfromthePC/AVaudiooutputterminals
cannot be adjusted using the AUDIO menu.
PC/AV output terminals
Video signals from PC1 and AV1 can be output to external
device. Use this terminal when you connect multiple monitors
in a daisy chain via DVI cable (commercially available). (See
the description on the right.)
Outputting images encoded with HDCP requires an HDCP-
compatible external device.
Images cannot be output in the following situations:
- In PC2/AV2 input mode
-WhenPIPSOURCEinthePIP/PbyPMenuissettoPC2
HDMI or AV2 HDMI
RS-232C input/output terminals
You can control the monitor from a PC by connecting a
commercially available RS-232 straight cable between this
terminal and the PC. (See Operation guide.)
LAN terminal
You can control the monitor from a PC on a network by
connecting a commercially available LAN cable between this
terminal and a network. (See Operation guide.)
Connecting external speakers
Besuretouseexternalspeakerswithanimpedanceof6Ω
andaratedinputofatleast7W.
(1) (2)
1.Whilepushingthetab,insertthetipofthecable.
2. Release the tab.
TIPS
• Besuretoconnectthe+and-terminalsandtheleftand
right speakers properly.
• Avoidshortcircuitingthe+and-terminals.
Connecting multiple monitors
You can connect multiple monitors (up to 5 monitors) in a
daisy chain by using the PC1/AV1 input terminals and PC/AV
output terminals of this monitor.
Connection example
shows the signal flow
PC/AV output
terminal PC1/AV1 input terminals
Digital signal (DVI) cables
(commercially available)
ToPCdigitalRGBoutputterminal
First monitor Second monitor
TIPS
• Thelengthofthesignalcablesorsurroundingenvironment
may affect the image quality.
• Thescreenmaynotdisplayproperlywhenusingterminals
other than PC1/AV1 for the input mode. In this case, turn
off the power to all the monitors connected in a daisy chain
and then turn the power on again.
• WhenconnectingmonitorsinadaisychainsetAUTO
INPUT CHANGE to OFF.

12
E
Installing the batteries
1. Press the cover gently and slide it in the direction of the
arrow.
2. See the instructions in the compartment and put in the
suppliedbatteries(R-6(“AA”size)x2)withtheirplus(+)
and minus (-) sides oriented correctly.
3. Close the cover.
TIPS
• Thesuppliedbatteries(R-6(“AA”size)x2)maybecome
exhausted faster depending on the storage condition. It is
recommended that you replace them with new batteries
(commerciallyavailable)earlierthanspecied.
• Ifyouwillnotusetheremotecontrolforalongtime,
remove the batteries.
• Usemanganeseoralkalinebatteriesonly.
Remote control operation range
The operation range of the remote control unit is approx. 16.4
feet (5 m) at an angle of approx 10° from the center to the
top/bottom/right/left of the remote control sensor.
10°
16.4 feet (5 m)
16.4 feet (5 m)
16.4 feet (5 m)
Remote control sensor
10°
TIPS
• Donotexposetheremotecontrolunittoshockbydropping
or stepping on it. This could lead to a malfunction.
• Donotexposetheremotecontrolunittoliquids,anddonot
place it in an area with high humidity.
• Theremotecontrolunitmaynotworkproperlyiftheremote
control sensor is under direct sunlight or strong lighting.
• Objectsbetweentheremotecontrolunitandtheremote
control sensor may prevent proper operation.
• Replacethebatterieswhentheyrunlowasthismay
shorten the remote control’s operation range.
• Ifauorescentlightisilluminatedneartheremotecontrol
unit, it may interfere with proper operation.
• Donotuseitwiththeremotecontrolofotherequipment
such as air conditioner, stereo components, etc.
Preparing the Remote Control Unit
Connecting the Power Cord
Caution
• Donotuseapowercordotherthantheonesuppliedwith
the monitor.
1. Turn off the main power switch.
2. Plug the power cord (supplied) into the AC input terminal.
3. Plug the power cord (supplied) into the AC power outlet.
AC input terminal
2
1
Main power switch
For power
outlet
Power cord (Supplied)
3

ENGLISH
13 E
Removing the Temporary Stand
Prepare wall-hanging brackets or a stand to mount the monitor unit. Read the manual for the brackets or stand for the proper
mounting procedure. (The screw holes for mounting brackets (M10 x 4 holes) are provided on the rear of the monitor.)
Caution
• Themonitorisheavy.Makesuretohandlethemonitorwithatleast2people.
• Thismonitorisxedtothetemporarystandwhenshippedfromthefactory.Pleasenotethatthisstandisfortemporaryuse
only until the monitor is properly mounted.
• Thetemporarystandisspecicallydesignedforthismonitor.Donotuseforotherdevices.
1. Hold the monitor with the handles to prevent it
fromfallingdown,andremovethestandxing
screws (4).
2. Lift the monitor by holding it with the handles and
the underside of the unit.
3. Whentheinstallationiscomplete,attachthe
included stand hole protection covers, using the
supplied screws.
(1) Fold the sheet perpendicularly with the
adhesive side inward.
(2) Remove the adhesive cover and attach the
sheet to the monitor.
1
2
Screws Screws

14
E
Turning Power On/Off
Caution
• TurnonthemonitorrstbeforeturningonthePCor
playback device.
Turning on the main power
Main power switch
Whenthemainpowerswitchisoff,themonitorcannotbe
turnedonusingthePOWERbuttonontheremotecontrolunit.
Turning power on/off
PressthePOWERbuttontoturnthepowerON/OFF.
INPUT
Power LED
Status of a power LED Status of the monitor
Green lighting Power “On”
Orange lighting Power “Off” (Standby mode)
Greenashing Input signal standby mode
(input using a PC)
Caution
• WhenswitchingthemainpowerswitchorthePOWER
button off and back on, always wait for at least 5 seconds.
A short interval may result in a malfunction.
TIPS
• Ifthemonitorisintheinputsignalstandbymodeandyou
pressthePOWERbuttonontheremotecontrolunit,the
monitor enters standby mode.
• Youcanturnon/offthemonitorbypressingthepower
switch of the monitor.
• SettingtheSCHEDULEashesthepowerLEDalternately
in red and orange in standby mode.
• WhenSTANDBYMODEissettoSTANDARD,startuptime
can be reduced. Note, however that, more power will be
consumed in standby mode.
nDate/time setting
• Ifthetimehasyettobesetwhenthemonitorisrstturned
on, the date/time setting screen appears. Set the date and
time.
DATE/TIME SETTING
SET
CANCEL
08
//
OK···[MENU]
20 01
/ 01 / 00 00 :
::
1. Press , , or to select the date and
time, and press or to change the numerical
values.
2. Select SET and then press
MENU
.
• Besuretosetthedateandtime.
• Thedate/timesettingscreenwillcloseautomaticallyifno
operation is performed for about 15 seconds. The date
and time can be set using DATE/TIME SETTING from
the OPTION menu when the date/time setting screen
disappears.
TIPS
• Set the date in “Year/Month/Day” order.
• Set the time on a 24-hour basis.
• The clock stops after the power-off status continues for
approximately 1 week.* The date/time setting screen
appearsatpower-on.Besuretosetthedateandtime.
(* This is a guide. The power-off status that stops the clock
depends on the status of the monitor.)
Disabling power on/off operations
Power on/power off operations can be disabled in order to
protect the monitor from an accidental power off. Set the
ADJUSTMENT LOCK in FUNCTION menu to “2”. (See
Operation guide.)

ENGLISH
15 E
Troubleshooting
Beforecallingforrepairservices,makesurefollowingchecks
for possible remedies to the encountered symptoms.
There is no picture or sound.
• Isthepowercorddisconnected?(Seepage12.)
• Isthemainpowerswitchsetto“OFF”?(Seepage14.)
• Isthemonitorinstandbymode(thepowerLEDilluminating
inorange)?(Seepage14.)
• Makesurecorrectinputmodeisselected.(SeeOperation
guide.)
• Ifanyexternalequipmentisconnected,makesurethe
equipment is operating (playing back).
Remote control does not work.
• Arethebatteriesinsertedwithpolarity(+,-)aligned?(See
page 12.)
• Arethebatteriesexhausted?(Seepage12.)
• Pointtheremotecontrolunittowardthemonitor’sremote
control sensor. (See page 12.)
• Isthemenudisplayhiddenorisoperationdisabled?(See
Operation guide.)
Sound from left and right speakers is reversed.
Sound is heard from only one side.
• Areaudiocablesconnectedproperly?(Seepages10and
11.)
• Makesureaudiocablesforexternalspeakersare
connected properly: left and right cables may be reversed
or one of the two cables may not be connected. (See page
11.)
• CheckthesettingofBALANCEforAUDIOmenu.(See
Operation guide.)
There is a picture but no sound.
• Isthesoundmuted?
• Makesurethevolumeisnotsettominimum.
• IsthePCaudiocable(commerciallyavailable)connected?
• Areaudiocablesconnectedproperly?
• Istheaudiosignalinputproperlytotheaudioinputterminal
correspondingtotheselectedvideoinputterminal?
• WhenPC2orAV2isused,isthesettingofHDMIAUDIO
SELECTcorrect?(SeeOperationguide.)
Unstable video.
• Thesignalmaybeincompatible.
• TrytheautomaticscreenadjustmentwhenthePC3input
terminal or PC4 input terminals is used.
PC1 or AV1 does not appear properly.
• IsthesettingofDVISELECTcorrect?(SeeOperation
guide.)
• Istheinputsignalcompatiblewiththismonitor?(Seepages
10 and 17.)
• Turnoffthepowertotheconnectedequipmentandthen
turn the power on again.
• Ifthemonitorsareconnectedinadaisychain,turnoffthe
power to all the monitors connected in a daisy chain and
then turn the power on again.
PC2 or AV2 does not appear properly.
• IsthesettingofHDMISELECTcorrect?(SeeOperation
guide.)
• IstheHDMIcableHDMIstandardcompliant?Themonitor
will not work with cables that are not standard compliant.
• Istheinputsignalcompatiblewiththismonitor?(Seepages
10 and 17.)
PC4 or AV3 does not appear properly.
•
IsthesettingofBNCSELECTcorrect?(SeeOperationguide.)
• Istheinputsignalcompatiblewiththismonitor?(Seepages
10 and 17.)
Control buttons do not work.
There is no picture.
• Somekindofloadnoisesfromoutsidemightinterferewith
normal operation. Turn off the power and turn it on after
waiting at least 5 seconds, and then check the operation.
The input mode changes automatically.
• WhentheAUTOINPUTCHANGEisONandnosignal
is present in a selected input mode, the AUTO INPUT
CHANGE automatically changes the selected mode to a
mode where a video signal is present.
The input mode may change in the following cases:
-Whenacomputerisinstandbymode.
-Whenvideoplayisstoppedwithaplaybackdevice.
Power LED ashes red.
“STATUS [xxxx]” appears in the corner of the screen.
• Hardwarehasaproblem.Turnoffthemonitorandrequest
repair from your SHARP dealer.
(WhenSTATUSALERTissettoOSD&LED.Thisvaries
depending on the setting.)
When “AUTO DIMMING” is displayed.
• Whentheinternaltemperatureofthemonitorrises
excessively, the brightness of the backlight automatically
decreases in order to prevent a further temperature rise. If
you attempt to use to adjust the brightness while
the monitor is in this state, “AUTO DIMMING” is displayed
and you cannot change the brightness.
• Removethecauseoftheexcessivetemperaturerise.
The monitor sometimes makes a cracking sound.
• Youmayhearcrackingsoundfromthemonitor.This
happens when the cabinet slightly expands and contracts
according to change in temperature. This does not affect
the monitor’s performance.
The Power LED is ashing in red and green alternately.
When “TEMPERATURE” is displayed in the corner of the
screen.
• Whentheinternaltemperatureofthemonitorrises
excessively, the brightness of the backlight decreases
automatically in order to prevent high-temperature-
relatedproblems.Whenthisoccurs,“TEMPERATURE”is
displayedonthescreenandthePowerLEDashesred
andgreenalternately.(WhenTEMPERATUREALERTis
settoOSD&LED.Thisvariesdependingonthesetting.)
• Iftheinternaltemperaturerisesfurther,themonitor
automatically enters standby mode. (The Power LED
continuesashingredandgreenalternately.)
• Removethecauseoftheexcessivetemperaturerise.
- If the monitor enters standby mode due to a rise in
temperature, to return to normal display, turn the power
switch off and then back on again. The monitor, however,
will enter standby mode again if the cause of the
temperature rise is not eliminated. (See page 9.)
- Check whether the monitor is placed at a location where
a quick rise in temperature is likely. Internal temperature
rises quickly if the vents on the monitor are blocked.
- Internal temperature rises quickly if dust accumulates
inside the monitor or around the vents. Remove dust if
possible. Ask Sharp dealer about removing internal dust.

16
E
Specications
nProduct Specications
Model PN-S655
LCD element 65" wide (163.9 cm diagonal) ASV low-reflection black TFT LCD
Max. resolution (pixels) 1920 x 1080
Max. colors 16.77 M colors (8 bits/color)
Pixel pitch 0.744 mm (H) x 0.744 mm (V)
Viewing angle 176°right/left/up/down(contrastratio≥10)
Screen active area inch (mm) 56-1/4 x 31-5/8 (1428 x 804)
Computer input signal Digital (DVI 1.0 standard-compliant), AnalogRGB(0.7Vp-p)[75Ω]
Sync signal Horizontal/vertical separate (TTL: positive/negative), Sync-on-green,
Composite sync (TTL: positive/negative)
Video color system PAL, PAL-60, SECAM, NTSC (3.58 MHz), NTSC (4.43 MHz)
Plug and play VESADDC2B
Power management VESA DPMS, DVI DMPM
Input terminals PC/AV Digital DVI-D 24 pin (HDCP compatible) x 1
HDMI x 1
PC Analog Mini D-sub 15 pin, 3 rows x 1
BNC*1*2 x 1
Audio 3.5 mm mini stereo jack x 1
AV Composite video BNCx1
S-video x 1
Component BNC(Y, Cb/Pb, Cr/Pr)*1 x 1
Audio RCA pin (L/R) x 1
Serial (RS-232C) D-sub 9 pin x 1
Output terminals PC/AV Digital DVI-D 24 pin x 1
Audio RCA pin (L/R) x 1
Serial (RS-232C) D-sub 9 pin x 1
Speaker 7W+7W[6Ω]
LAN terminal 10BASE-T/100BASE-TX
Power requirement AC 100 V - 240 V, 50/60 Hz
Operating temperature 32°F to 104°F (0°C to 40°C)
Operating humidity 20% to 80% (no condensation)
Power consumption 480W(Inputsignalwaitingmode:14W*3,Standbymode:2.0W*4)
Dimensions inch (mm) Approx. 61-7/8 x 4-15/16 x 36-5/16 (1,572 x 126 x 923) (excluding protrusions)
Weight lbs. (kg) Approx. 136.7 (62) (excluding the temporary stand)
*1 Cannot be used simultaneously.
*2 Does not support plug and play.
*3 WhenAUTOINPUTCHANGEissettoOFF.
*4 WhenSTANDBYMODEissettoLOWPOWER,LANandSCHEDULEarenotused.WhenSTANDBYMODEissettoSTANDARD,14W.
Asapartofourpolicyofcontinuousimprovement,SHARPreservestherighttomakedesignandspecicationchangesforproductimprovement
withoutpriornotice.Theperformancespecicationguresindicatedarenominalvaluesofproductionunits.Theremaybesomedeviationsfrom
these values in individual units.
nPower management
ThismonitorconformstoVESADPMSandDVIDMPM.Bothyourvideocardandcomputermustsupportthesamestandardin
order for the monitor’s power management function to work.
DPMS: Display Power Management Signaling
DPMS Screen
Power
consumption
Hsync Vsync
ON STATE Display 480W Yes Yes
STANDBY No
display 14W*
No Yes
SUSPEND Yes No
OFF STATE No No
DMPM: Digital Monitor Power Management
DMPM Screen Power
consumption
Monitor ON Display 480W
Active OFF No display 14W*
* WhenAUTOINPUTCHANGEissettoOFF.

ENGLISH
17 E
nCompatible signal timing (PC)
VESA
Wide
US TEXT
Sun
Screen resolution Hsync Vsync Dot frequency Digital
640 × 480
800 × 600
848 × 480
1024 × 768
1152 × 864
1280 × 768
1280 × 960
1280 × 1024
1360 × 768
1400 × 1050
1600 × 1200*1
1680 × 1050
1920 × 1200*1
1280 × 720
1920 × 1080
720 × 400
1024 × 768
1152 × 900
1280 × 1024
1600 × 1000
31.5kHz
37.9kHz
37.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
31.0kHz
48.4kHz
56.5kHz
60.0kHz
67.5kHz
47.8kHz
60.3kHz
60.0kHz
64.0kHz
80.0kHz
47.7kHz
65.3kHz
75.0kHz
65.3kHz
74.0kHz
44.7kHz
66.3kHz
67.5kHz
31.5kHz
48.3kHz
53.6kHz
56.6kHz
61.8kHz
71.8kHz
71.7kHz
81.1kHz
68.6kHz
60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
60Hz
70Hz
75Hz
75Hz
60Hz
75Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
60Hz
70Hz
60Hz
66Hz
70Hz
66Hz
76.2Hz
67.2Hz
76Hz
66Hz
25.175MHz
31.5MHz
31.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz
33.75MHz
65.0MHz
75.0MHz
78.75MHz
108.0MHz
79.5MHz
102.25MHz
108.0MHz
108.0MHz
135.0MHz
85.5MHz
121.75MHz
162.0MHz
146.25MHz
154.0MHz
74.4MHz
148.5MHz
148.5MHz
28.3MHz
64.13MHz
70.4MHz
74.25MHz
94.88MHz
108.23MHz
117.01MHz
134.99MHz
135.76MHz
Yes
Yes
Yes
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
-
-
-
-
Analog(PC3/PC4)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
DVI(PC1) HDMI(PC2)
Yes
Yes
Yes
-
Yes
Yes
Yes
-
Yes
Yes
Yes
Yes
-
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
-
-
-
-
-
-
-
*1 Displays a reduced image.
* All are compliant only with non-interlaced.
* Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input.
* The frequency values for the Sun are reference values.
Specications
nDimensional Drawings
Note that the values shown are approximate values.
13/16 [20]
Opening height
(31-3/4 [807])
Opening width (56-3/8 [1432])
Unit: inch [mm]
61-7/8 [1572]
4-15/16
[126] 1/4 [7]
58-7/16 [1485]
33-7/8 [860]
13/16 [20]
36-5/16 [923]
3-3/8 [85] 3-3/8 [85]
25-9/16 [650]
17-5/16 [440]
15-1/2 [393]
Screw holes for
mounting brackets
(M10 x 4 holes)
23-7/16 [595]
6-1/8 [155]
 Whenmountingthemonitor,readthemanualofthebracketsorstandfortheirmountingprocedure.Thescrewholesfor
mounting brackets (M10 x 4 holes) are provided on the rear of the monitor.
Note that screw hole depth of the monitor is 13/16 inch (20 mm). Loose holding may cause the product to fall, resulting in
serious personal injuries as well as damage to the product. The screw and hole should come together with over 3/8 inch (10
mm) length of thread. Use the bracket which applied UL1678 standard, and which can endure at least 4 times or more the
weight of the monitor.

18
E
Specications
nDDC (plug and play)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters
isexchangedbetweenthetwo.ThisfunctioncanbeusedifthecomputersupportsDDCandithasbeenconguredtodetect
plug-and-play monitors.
ThereareseveraltypesofDDC,dependingonthecommunicationmethodused.ThismonitorsupportsDDC2B.
nPC1/AV1 input terminal pins
(DVI-D24 pin)
No. Function No. Function
1 TMDS data 2- 13 N.C.
2TMDSdata2+ 14 +5V
3 TMDS data 2/4 shield 15 GND
4 N.C. 16 Hot-plug detection
5 N.C. 17 TMDS data 0-
6 DDC clock 18 TMDSdata0+
7 DDC data 19 TMDS data 0/5 shield
8 N.C. 20 N.C.
9 TMDS data 1- 21 N.C.
10 TMDSdata1+ 22 TMDS clock shield
11 TMDS data 1/3 shield 23 TMDSclock+
12 N.C. 24 TMDS clock-
nPC3 input terminal pins
(Mini D-sub 15 pin)
No. Function No. Function
1 Red video signal input 9 +5V
2 Green video signal input 10 GND
3Bluevideosignalinput 11 N.C.
4 N.C. 12 DDC data
5 GND 13 Hsync signal input
6 GND for red video signal 14 Vsync signal input
7GND for green video signal 15 DDC clock
8 GND for blue video signal
nPC/AV output terminal pins
(DVI-D24 pin)
No. Function No. Function
1 TMDS data 2- 13 N.C.
2TMDSdata2+ 14 +5V
3 TMDS data 2/4 shield 15 GND
4 N.C. 16 Hot-plug detection
5 N.C. 17 TMDS data 0-
6 DDC clock 18 TMDSdata0+
7 DDC data 19 TMDS data 0/5 shield
8 N.C. 20 N.C.
9 TMDS data 1- 21 N.C.
10 TMDSdata1+ 22 TMDS clock shield
11 TMDS data 1/3 shield 23 TMDSclock+
12 N.C. 24 TMDS clock-
nPC2/AV2 input terminal pins
(HDMITM Connector)
No. Function No. Function
1TMDSdata2+ 11 TMDS clock shield
2 TMDS data 2 shield 12 TMDS clock-
3 TMDS data 2- 13 CEC
4TMDSdata1+ 14 N.C.
5 TMDS data 1 shield 15 SCL
6 TMDS data 1- 16 SDA
7TMDSdata0+ 17 DDC/CEC GND
8 TMDS data 0 shield 18 +5V
9 TMDS data 0- 19 Hot-plug detection
10 TMDSclock+
nRS-232C input terminal pins
(D-sub 9 pin)
No. Function No. Function
1 N.C. 6 N.C.
2 Transmitted data 7 N.C.
3 Received data 8 N.C.
4 N.C. 9 N.C.
5 GND
nRS-232C output terminal pins
(D-sub 9 pin)
No. Function No. Function
1 N.C. 6 N.C.
2 Received data 7 N.C.
3 Transmitted data 8 N.C.
4 N.C. 9 N.C.
5 GND