Sharp XG-SV200X User guide

MODEL
XG-SV100W
XG-SV200X
DATA PROJECTOR
SETUP MANUAL
Connecting Pin Assignments ............................................................ 2
RS-232C Specifications and Commands ......................................... 4
Operating the Projector Using the PJLinkTM Protocol .................. 10
Setting up the Projector Network Environment ............................... 11
1. Connecting the Projector to a Computer ............................................ 12
2. Setting an IP Address for the Computer ............................................. 13
3. Setting up a Network Connection for the Projector ............................ 15
Controlling the Projector via LAN ................................................... 17
Controlling the Projector Using Internet Explorer.................................... 17
Confirming the Projector Status (Status)................................................. 18
Controlling the Projector (Control)........................................................... 18
Setting and Adjusting the Projector (Settings & Adjustments)................ 19
Setting the Security (Network – Security)................................................ 19
Making General Settings for the Network (Network – General)............... 20
Setting for Sending E-mail when an Error Occurs
(Mail – Originator Settings) ............................................................ 20
Setting Error Items and Destination Addresses to which E-mail is to be
Sent when an Error Occurs (Mail – Recipient Settings) ................ 21
Setting Error Items and the URL that are to be Displayed
when an Error Occurs (Service & Support – Access URL)............ 21
Resetting the Lamp Timer of the Projector via LAN ..................... 22
Troubleshooting................................................................................ 24

-2
Connecting Pin Assignments
COMPUTER/COMPONENT 1, 2 input and COMPUTER/COMPONENT output Terminals:
mini D-sub 15 pin female connector
COMPUTER Input/Output COMPONENT Input/Output
Pin No. Signal Pin No. Signal
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Video input (red)
Video input (green/sync on green)
Video input (blue)
Not connected
Not connected
Earth (red)
Earth (green/sync on green)
Earth (blue)
Not connected
GND
Not connected
Bi-directional data
Horizontal sync signal: TTL level
Vertical sync signal: TTL level
Data clock
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
PR (CR)
Y
PB (CB)
Not connected
Not connected
Earth (PR)
Earth (Y)
Earth (PB)
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
HDMI Terminal
Pin No. Name Pin No. Name
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
T.M.D.S. Data 2+
T.M.D.S. Data 2 Shield
T.M.D.S. Data 2–
T.M.D.S. Data 1+
T.M.D.S. Data 1 Shield
T.M.D.S. Data 1–
T.M.D.S. Data 0+
T.M.D.S. Data 0 Shield
T.M.D.S. Data 0 –
T.M.D.S. Clock+
11.
12.
13.
14.
15.
16.
17.
18.
19.
T.M.D.S. Clock Shield
T.M.D.S. Clock–
CEC
Utility
SCL
SDA
DDC/CEC ground
+5V power
Hot plug detection
RS-232C Terminal: D-sub 9 pin male connector of the DIN-D-sub RS-232C adaptor
Pin No. Signal Name I/O Reference
1.
2.
3.
4.
5.
6.
7.
8.
9.
RD
SD
SG
RS
CS
Receive Data
Send Data
Signal Ground
Request to Send
Clear to Send
Input
Output
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
5
10
15
1
11
6
5
10
15
1
11
6
218
19 1
218
19 1
15
69
15
69

-3
RS-232C Cable recommended connection: D-sub 9 pin female connector
Pin No. Signal Pin No. Signal
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
Projector
Pin No.
Computer
Pin No.
4
5
6
4
5
6
USB Terminal: Type B USB connector LAN Terminal: LAN (RJ-45)
Pin No. Signal Name Pin No. Signal Pin No. Signal
1.
2.
3.
4.
VCC
USB–
USB+
SG
USB power
USB data–
USB data+
Signal Ground
1.
2.
3.
4.
TX+
TX–
RX+
5.
6.
7.
8.
RX–
51
96
51
96
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
•
Note
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
•
Note
43
12
43
12
8... 18 ... 1
Connecting Pin Assignments

-4
RS-232C Specifications and Commands
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross
type, commercially available) to the projector. (See page 25 of the projector's operation manual for
connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard. Parity bit: None
Baud rate*: 9,600 bps / 38,400 bps / 115,200 bps Stop bit: 1 bit
Data length: 8 bits Flow control: None
*Set the projector's baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code.
After the projector processes the command from the computer, it sends a response code to the
computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4 Return code (0DH)
Command 4-digit Parameter 4-digit
Response code format
Normal response
Problem response (communication error or incorrect command)
OK Return code (0DH) E R R Return code (0DH)
Info
When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds
after the power has been turned on, and then transmit the commands.
After sending an input selection or picture adjustment command and then receiving an “OK” response
code, the projector may take some time to process the command. If a second command is sent while the
projector is still processing the first command, you may receive an “ERR” response code. If this happens,
try resending the second command.
When more than one code is being sent, send each command only after the response code for the
previous command from the projector is verified.
“POWR????”, “TABN _ _ _ 1”, “TLPS _ _ _ 1”, “TPOW _ _ _ 1”, “TLPN _ _ _ 1”, “TLTT _ _ _ 1”,
“TLTM _ _ _ 1”, “TLTL _ _ _ 1”, “TNAM _ _ _ 1”, “MNRD _ _ _ 1”, “PJN0 _ _ _ 1”
− When the projector receives the special commands shown above:
* The on-screen display will not disappear.
* The “Auto Power Off” timer will not be reset.
− The special commands are available for applications that require continuous polling.
•
•
•
•
If an underbar (_) appears in the parameter column, enter a space.
If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under
Control Contents.
•
•
Note

-5
Commands
Example: When turning on the projector, make the following setting.
Computer Projector
POWR___1
o
m
OK
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Power On P O W R ___1 OK or ERR OK
Off P O W R ___0 OK OK or ERR
Status POWR????1 0
Projector Condition T A B N ___10:Normal
1: Temp High
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
0: Normal
1: Temp High
2: Fan Error
4: Cover Open
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
64:
Temp Abnormally High
Lamp Status T L P S ___1 0: Off, 1: On, 2: Retry
3: Waiting, 4: Lamp Error
0: Off, 4: Lamp Error
Power Status T P O W ___1 1: On, 2: Cooling 0: Standby
Quantity T L P N ___11
Usage Time(Hour) T L T T ___1 0 – 9999(Integer)
Usage Time(Minute) T L T M ___1 0, 15, 30, 45
Life(Percentage) TLTL___1 0% – 100%(Integer)
Name Model Name Check T N A M ___1XGSV100W/XGSV200X
Model Name Check M N R D ___1 XG-SV100W/XG-SV200X
Projector Name Setting 1
(First 4 characters) *1
PJN1****OKorERR
Projector Name Setting 2
(Middle 4 characters) *1
PJN2****OKorERR
Projector Name Setting 3
(Last 4 characters) *1
PJN3****OKorERR
Projector Name Check P J N 0 ___1ProjectorName
Input Change COMPUTER1 I R G B ___1 OK or ERR ERR
COMPUTER2 *2 I R G B ___2 OK or ERR ERR
HDMI I R G B ___3 OK or ERR ERR
S-VIDEO I V E D ___1 OK or ERR ERR
VIDEO I V E D ___2 OK or ERR ERR
InputRGBCheck IRGB????
1: COMPUTER1, 2: COMPUTER2,
3: HDMI, ERR
ERR
Input Video Check I V E D ? ? ? ? 1: S-VIDEO, 2: VIDEO or ERR ERR
Input Mode Check I M O D ? ? ? ? 1: RGB, 2: VIDEO ERR
InputCheck ICHK????1:COMPUTER1,
2: COMPUTER2, 3: HDMI,
4: S-VIDEO, 5: VIDEO
ERR
Volume Volume(0 – 60) V O L A __**OKorERR ERR
Volume up/down(-10 – +10) V O U D _***OKorERR ERR
Keystone Vertical -80 – +80 K E Y S _***OKorERR ERR
KEYV_***OKorERR ERR
Horizontal -60 – +60 K E Y H _***OKorERR ERR
AV Mute On I M B K ___1 OK or ERR ERR
Off I M B K ___0 OK or ERR ERR
Freeze On F R E Z ___1 OK or ERR ERR
Off F R E Z ___0 OK or ERR ERR
Auto Sync Start A D J S ___1 OK or ERR ERR
Resize COMPUTER1 Normal R A S R ___1 OK or ERR ERR
16:9 R A S R ___2 OK or ERR ERR
Native R A S R ___3 OK or ERR ERR
Full R A S R ___5 OK or ERR ERR
Border (XG-SV200X only) R A S R ___6 OK or ERR ERR
Area Zoom R A S R __10OKorERR ERR
V-Stretch R A S R __11OKorERR ERR
COMPUTER2 Normal R B S R ___1 OK or ERR ERR
16:9 R B S R ___2 OK or ERR ERR
Native R B S R ___3 OK or ERR ERR
Full R B S R ___5 OK or ERR ERR
Border (XG-SV200X only) R B S R ___6 OK or ERR ERR
Area Zoom R B S R __10OKorERR ERR
V-Stretch R B S R __11OKorERR ERR
RS-232C Specifications and Commands

-6
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Resize HDMI Normal R C S R ___1 OK or ERR ERR
16:9 R C S R ___2 OK or ERR ERR
Native R C S R ___3 OK or ERR ERR
Full R C S R ___5 OK or ERR ERR
Border (XG-SV200X only) R C S R ___6 OK or ERR ERR
Area Zoom R C S R __10OKorERR ERR
V-Stretch R C S R __11OKorERR ERR
S-VIDEO Normal R A S V ___1 OK or ERR ERR
16:9 R A S V ___2 OK or ERR ERR
Border (XG-SV200X only) R A S V ___3 OK or ERR ERR
Area Zoom R A S V __10OKorERR ERR
V-Stretch R A S V __11OKorERR ERR
VIDEO Normal R B S V ___1 OK or ERR ERR
16:9 R B S V ___2 OK or ERR ERR
Border (XG-SV200X only) R B S V ___3 OK or ERR ERR
Area Zoom R B S V __10OKorERR ERR
V-Stretch R B S V __11OKorERR ERR
ALL Reset ALRE___1 OK or ERR ERR
COMPUTER1 INPUT Picture Mode Standard R A P S __10OKorERR ERR
Presentation RAPS__11OKorERR ERR
Movie RAPS__12OKorERR ERR
Game RAPS__13OKorERR ERR
sRGB RAPS__14OKorERR ERR
Contrast -30 – +30 R A P I _* * * OK or ERR ERR
Bright -30 – +30 R A B R _* * * OK or ERR ERR
Red -30 – +30 R A R D _* * * OK or ERR ERR
Blue -30 – +30 R A B E _* * * OK or ERR ERR
Color -30 – +30 R A C O _* * * OK or ERR ERR
Tint -30 – +30 R A T I _* * * OK or ERR ERR
Sharp -30 – +30 R A S H _* * * OK or ERR ERR
CLR Temp -2 – +2 R A C T __**OKorERR ERR
BrilliantColor™ 0 – +2 R A W E ___* OK or ERR ERR
DNR Off R A N R ___0 OK or ERR ERR
Level 1 R A N R ___1 OK or ERR ERR
Level 2 R A N R ___2 OK or ERR ERR
Level 3 R A N R ___3 OK or ERR ERR
Picture Reset R A R E ___1 OK or ERR ERR
SignalType Auto IASI___0 OK or ERR ERR
RGB I A S I ___1 OK or ERR ERR
YPbPr I A S I ___2 OK or ERR ERR
Audio Input Audio 1 R A A I ___1 OK or ERR ERR
Audio 2 R A A I ___2 OK or ERR ERR
COMPUTER2 INPUT Picture Mode Standard R B P S __10OKorERR ERR
Presentation R B P S __11OKorERR ERR
Movie R B P S __12OKorERR ERR
Game R B P S __13OKorERR ERR
sRGB R B P S __14OKorERR ERR
Contrast -30 – +30 R B P I _* * * OK or ERR ERR
Bright -30–+30 RBBR_* * * OK or ERR ERR
Red -30 – +30 R B R D _* * * OK or ERR ERR
Blue -30 – +30 R B B E _* * * OK or ERR ERR
Color -30 – +30 R B C O _* * * OK or ERR ERR
Tint -30 – +30 R B T I _* * * OK or ERR ERR
Sharp -30 – +30 R B S H _* * * OK or ERR ERR
CLR Temp -2 – +2 R B C T __**OKorERR ERR
BrilliantColor™ 0 – +2 R B W E ___* OK or ERR ERR
DNR Off R B N R ___0 OK or ERR ERR
Level 1 R B N R ___1 OK or ERR ERR
Level 2 R B N R ___2 OK or ERR ERR
Level 3 R B N R ___3 OK or ERR ERR
PictureReset RBRE ___1 OK or ERR ERR
Signal Type Auto I B S I ___0 OK or ERR ERR
RGB I B S I ___1 OK or ERR ERR
YPbPr I B S I ___2 OK or ERR ERR
Audio Input Audio 1 R B A I ___1 OK or ERR ERR
Audio 2 R B A I ___2 OK or ERR ERR
RS-232C Specifications and Commands

-7
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
HDMI INPUT Picture Mode Standard R C P S __10OKorERR ERR
Presentation R C P S __11OKorERR ERR
Movie R C P S __12OKorERR ERR
Game R C P S __13OKorERR ERR
sRGB R C P S __14OKorERR ERR
Contrast -30 – +30 R C P I _***OKorERR ERR
Bright -30 – +30 R C B R _***OKorERR ERR
Red -30 – +30 R C R D _***OKorERR ERR
Blue -30 – +30 R C B E _***OKorERR ERR
Color -30 – +30 R C C O _***OKorERR ERR
Tint -30 – +30 R C T I _***OKorERR ERR
Sharp -30 – +30 R C S H _***OKorERR ERR
CLR Temp -2 – +2 R C C T __**OKorERR ERR
BrilliantColor™ 0 – +2 R C W E ___* OK or ERR ERR
DNR Off R C N R ___0 OK or ERR ERR
Level 1 R C N R ___1 OK or ERR ERR
Level 2 R C N R ___2 OK or ERR ERR
Level 3 R C N R ___3 OK or ERR ERR
Picture Reset R C R E ___1 OK or ERR ERR
Signal Type Auto I C S I ___0 OK or ERR ERR
RGB I C S I ___1 OK or ERR ERR
YPbPr I C S I ___2 OK or ERR ERR
Audio Input Audio 1 R C A I ___1 OK or ERR ERR
Audio 2 R C A I ___2 OK or ERR ERR
HDMI R C A I ___3 OK or ERR ERR
Dynamic
Range
Auto H M C D ___0 OK or ERR ERR
Standard H M C D ___1 OK or ERR ERR
Enhanced H M C D ___2 OK or ERR ERR
S-VIDEO INPUT Picture Mode Standard V A P S __10OKorERR ERR
Presentation VAPS__11OKorERR ERR
Movie VAPS__12OKorERR ERR
Game VAPS__13OKorERR ERR
Contrast -30 – +30 V A P I _***OKorERR ERR
Bright -30 – +30 V A B R _***OKorERR ERR
Red -30 – +30 V A R D _***OKorERR ERR
Blue -30 – +30 V A B E _***OKorERR ERR
Color -30 – +30 V A C O _***OKorERR ERR
Tint -30 – +30 V A T I _***OKorERR ERR
Sharp -30 – +30 V A S H _***OKorERR ERR
CLR Temp -2 – +2 V A C T __**OKorERR ERR
BrilliantColor™ 0 – +2 V A W E ___* OK or ERR ERR
DNR Off V A N R ___0 OK or ERR ERR
Level 1 V A N R ___1 OK or ERR ERR
Level 2 V A N R ___2 OK or ERR ERR
Level 3 V A N R ___3 OK or ERR ERR
Picture Reset V A R E ___1 OK or ERR ERR
Audio Input Audio 1 V A A I ___1 OK or ERR ERR
Audio 2 V A A I ___2 OK or ERR ERR
VIDEO INPUT Picture Mode Standard V B P S __10OKorERR ERR
Presentation V B P S __11OKorERR ERR
Movie V B P S __12OKorERR ERR
Game V B P S __13OKorERR ERR
Contrast -30 – +30 V B P I _***OKorERR ERR
Bright -30 – +30 V B B R _***OKorERR ERR
Red -30 – +30 V B R D _***OKorERR ERR
Blue -30 – +30 V B B E _***OKorERR ERR
Color -30 – +30 V B C O _***OKorERR ERR
Tint -30 – +30 V B T I _***OKorERR ERR
Sharp -30 – +30 V B S H _***OKorERR ERR
CLR Temp -2 – +2 V B C T __**OKorERR ERR
BrilliantColor™ 0 – +2 V B W E ___* OK or ERR ERR
DNR Off V B N R ___0 OK or ERR ERR
Level 1 V B N R ___1 OK or ERR ERR
Level 2 V B N R ___2 OK or ERR ERR
Level 3 V B N R ___3 OK or ERR ERR
Picture Reset V B R E ___1 OK or ERR ERR
Audio Input Audio 1 V B A I ___1 OK or ERR ERR
Audio 2 V B A I ___2 OK or ERR ERR
RS-232C Specifications and Commands

-8
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Clock -150 – +150 I N C L * * * * OK or ERR ERR
Phase -30 – +30 I N P H _* * * OK or ERR ERR
H-position -150–+150 IAHP****OKorERR ERR
V-position -60 – +60 I A V P _* * * OK or ERR ERR
Fine Sync Adjustment Reset I A R E ___1 OK or ERR ERR
Overscan On O V S N ___1 OK or ERR ERR
Off O V S N ___0 OK or ERR ERR
OSD Display On I M D I ___1 OK or ERR ERR
Off I M D I ___0 OK or ERR ERR
Video System Auto M E S Y ___1 OK or ERR ERR
PAL M E S Y ___2 OK or ERR ERR
SECAM M E S Y ___3 OK or ERR ERR
NTSC4.43 M E S Y ___4 OK or ERR ERR
NTSC3.58 M E S Y ___5 OK or ERR ERR
PAL-M M E S Y ___6 OK or ERR ERR
PAL-N M E S Y ___7 OK or ERR ERR
PAL-60 M E S Y ___8 OK or ERR ERR
Background Logo I M B G ___1 OK or ERR ERR
Blue I M B G ___3 OK or ERR ERR
None I M B G ___4 OK or ERR ERR
Eco+Quiet On T H M D ___1 OK or ERR ERR
Off T H M D ___0 OK or ERR ERR
Auto Sync On A A D J ___1 OK or ERR ERR
Off A A D J ___0 OK or ERR ERR
Auto Power Off On A P O W ___1 OK or ERR ERR
Off A P O W ___0 OK or ERR ERR
Auto Restart On A R E S ___1 OK or ERR ERR
Off A R E S ___0 OK or ERR ERR
STANDBY Mode Standard M O U T ___1 OK or ERR ERR
Eco M O U T ___0 OK or ERR ERR
PRJ Mode Reverse On I M R E ___1 OK or ERR ERR
Off I M R E ___0 OK or ERR ERR
Invert On I M I N ___1 OK or ERR ERR
Off I M I N ___0 OK or ERR ERR
Language English M E L A ___1 OK or ERR ERR
Deutsch M E L A ___2 OK or ERR ERR
Español M E L A ___3 OK or ERR ERR
Nederlands M E L A ___4 OK or ERR ERR
Français M E L A ___5 OK or ERR ERR
Italiano M E L A ___6 OK or ERR ERR
Svenska M E L A ___7 OK or ERR ERR
ME L A ___8 OK or ERR ERR
Português M E L A ___9 OK or ERR ERR
ME L A __10OKorERR ERR
ME L A __11OKorERR ERR
ME L A __12OKorERR ERR
ME L A __13OKorERR ERR
polski M E L A __14OKorERR ERR
Türkçe M E L A __15OKorERR ERR
ME L A __16OKorERR ERR
Magyar M E L A __17OKorERR ERR
TiӃng ViӋtME L A __18
OK or ERR ERR
Audio Out FAO A O U T ___1 OK or ERR ERR
VAO A O U T ___2 OK or ERR ERR
InternalSpeaker On ASPK___1 OK or ERR ERR
Off ASPK___0 OK or ERR ERR
RGB Frequency Check Horizontal T F R Q ___1 kHz(***.* or ERR) ERR
Vertical T F R Q ___2 Hz(***.* or ERR) ERR
Fan Mode Normal H L M D ___0 OK or ERR ERR
High H L M D ___1 OK or ERR ERR
Treble -30 − +30 A A T E _***OKorERR ERR
Bass -30 − +30 A A B A _***OKorERR ERR
WallColor Off WLCO _ _ _ 0OKorERR ERR
Blackboard WLCO _ _ _ 1OKorERR ERR
Whiteboard WLCO_ _ _ 2OKorERR ERR
COMPUTER2 Select *3 Input R B S E _ _ _ 0 OK or ERR ERR
Monitor Output R B S E _ _ _ 1 OK or ERR ERR
DLP®LinkTM Off 3 D E N _ _ _ 0 OK or ERR ERR
On 3 D E N _ _ _ 1 OK or ERR ERR
DLP®LinkTM Invert 3 D I V _ _ _ 1 OK or ERR ERR
RS-232C Specifications and Commands

-9
CONTROL CONTENTS COMMAND PARAMETER
RETURN
Power ON Standby mode
(or 30-second startup time)
Video Setup 0 IRE V I S U _ _ _ 0 OK or ERR ERR
7.5 IRE V I S U _ _ _ 1 OK or ERR ERR
Closed Caption
(For Americas only)
Off C L C A _ _ _ 0 OK or ERR ERR
CC1 C L C A _ _ _ 1 OK or ERR ERR
CC2 C L C A _ _ _ 2 OK or ERR ERR
LENS Focus(-255-+255) LNFO****OKorERR ERR
Zoom(-255-+255) LNZO****OKorERR ERR
VerticalLensShift(-800-+800)*6 LNSH****OKorERR ERR
LNUD****OKorERR ERR
HorizontalLensShift(-800-+800)*6 LNLR****OKorERR ERR
Lens Shift Center *6 L N P D _ _ _ 1 OK or ERR ERR
ROTATE*4 -800−+800 SVLR****OKorERR ERR
Rotate Indicator *4 On S V B L ___1 OK or ERR ERR
Off S V B L ___0 OK or ERR ERR
MEMORY Save(1-8) LNSV****OKorERR ERR
Load(1-8)*6 LNLO****OKorERR ERR
Clear(1-8) LNCR****OKorERR ERR
Mute On LNMM___1OKorERR ERR
Off LNMM___0OKorERR ERR
Lock On LNML___1OKorERR ERR
Off LNML___0OKorERR ERR
Reset Network Setting L N R E _ _ _ 1 OK or ERR OK or ERR
Restart Network L R E S _ _ _ 1 OK or ERR OK or ERR
LampTimerReset*5 LPRE0001ERR OKorERR
*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.
*2 When “COMPUTER2 Select” is set to “Monitor Output”, you may receive an “ERR” response code.
*3 When “COMPUTER2” is selected in the INPUT list, “COMPUTER2 Select” cannot be set to “Monitor
Output”.
*4 This command can send only when the ceiling-mount rotating module (AN-SV100T: commercially available)
is connected to the projector.
*5 The Lamp Timer Reset command is available only in standby mode.
*6 If the lens cover is not correctly attached, you may receive an “ERR” response code.
RS-232C Specifications and Commands

-10
Operating the Projector Using the PJLinkTM Protocol
The projector conforms with the PJLinkTM standard Class 1.
The commands to be used in controlling the projector by the PJLinkTM protocol are as
shown below.
CONTROL CONTENTS COMMAND RETURN
Power Control Off P O W R _ 0 OK or ERR3
On P O W R _ 1 OK or ERR3
Power Status Query P O W R _ ? 0: Standby Mode
1: Power On
2: Standby (Cooling)
3: Power On (Warming up)
Input List Query I N S T _ ? 11 12 21 22 31
Input Change COMPUTER1 I N P T _ 1 1 OK or ERR3
COMPUTER2 I N P T _ 1 2 OK or ERR3
HDMI I N P T _ 3 1 OK or ERR3
S-VIDEO I N P T _ 2 1 OK or ERR3
VIDEO I N P T _ 2 2 OK or ERR3
Input Status Query I N P T _ ? 11: COMPUTER1
12: COMPUTER2
31: HDMI
21: S-VIDEO
22: VIDEO
or ERR3
AV Mute Off A V M T _ 3 0 OK or ERR3
On A V M T _ 3 1 OK or ERR3
AV Mute Status Query A V M T _ ? 30: Off
31: On
or ERR3
Lamp Query L A M P _ ? 1st Number: Lamp Usage Time (Hour)
2nd Number: 0: Lamp Off 1: Lamp on
Error Condition Query E R S T _ ? 1st Byte: Fan Error Status
2nd Byte: Lamp Error Status
3rd Byte: Temp. Error Status
4th Byte: Cover Open Status
5th Byte: Not Used, Return 0
6th Byte: Other Error Status
0: No Error Detected
1: Warning
2: Error Detected
Projector Name Query * N A M E _ ? Projector Name
Manufacture Name Query I N F 1 _ ? SHARP
Pruduct Name Query I N F 2 _ ? XG-SV100W/XG-SV200X
Other Information Query I N F O _ ? Not used
Class Information Query C L S S _ ? 1
* You can set “Projector Name” at “Making General Setting for the Network (Network-General)” on page 20.
PJLinkTM Authentication:
The password to be used for PJLinkTM is the same as the one you have set in “Setting the Security (Network-
Security)” (page 19). When operating without authentication, do not set a password.
PJLinkTM Compliant:
This product conforms with the PJLink standard Class 1 and all Class 1 commands are implemented.
This product confirms with the PJLink standard specification version 1.00.
For additional information, visit “http://pjlink.jbmia.or.jp/english/”.

-11
Setting up the Projector Network Environment
This section describes the basic procedure for using the projector via the network.
If the network is already constructed, the projector's network settings may need to be
changed. Please consult your network administrator for assistance with these settings.
You can make network settings both on the projector and on the computer. The following
procedure is for making settings on the computer.
Network settings on the computer
Connect a LAN cable (Category 5, cross-over type) between the computer and projector.
LAN cable
(commercially available)
1. Connecting the projector to a computer
Page 12
Adjust the IP settings of the computer to enable one-to-one communications with the projector.
Temporarily change
the computer's IP
address.
2. Setting an IP address for the computer
Pages 13, 14
Adjust the projector network settings to conform to your network.
Use Internet Explorer
(version 6.0 or later)
to make various
projector settings.
3. Setting up a network connection for the projector
Pages 15, 16
Microsoft®, Windows®and Windows Vista®are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
PJLink is a registered trademark or an application trademark in Japan, the United States, Canada, E.U.,
China and/or other countries/regions.
All other company or product names are trademarks or registered trademarks of their respective
companies.
•
•
•

-12
1. Connecting the Projector
to a Computer
Establishing a one-to-one connection from
the projector to a computer. Using a
commercially available LAN cable (UTP
cable, Category 5, cross-over type) you can
configure the projector via the computer.
1
Disconnect the computer's LAN
cable from the existing network.
2Connect a commercially available
LAN cable (UTP cable, Category 5,
cross-over type) to the projector's
LAN terminal and connect the
other end of the cable to the
computer's LAN terminal.
3Plug the power cord into the AC
socket of the projector.
4Turn on the computer.
Info
Confirm that the LINK LED on the rear of the
projector illuminates. If the LINK LED does not
illuminate, check the following:
The LAN cable is properly connected.
The power switches of both the projector and
the computer are on.
•
•
1
A LAN cable being
connected to the network
A LAN cable being
connected to the network
2
LAN cable
(cross-over type, commercially available)
LAN cable
(cross-over type, commercially available)
3
4
ONON
This completes the connection. Now proceed to “2. Setting an IP Address for the Computer”.
Setting up the Projector Network Environment

-13
2. Setting an IP Address for
the Computer
The following describes how to make
settings in Windows Vista®.
1Log on the network using the
administrator's account for the
computer.
2Click “start”, and click “Control
Panel”.
3Click “View network status and
tasks” of “Network and Internet”,
and click “View status” in the new
window.
This manual uses examples to explain the
operations in Category View. If you are using
Classic View, double-click “Network and
Sharing Center”.
4Click “Properties”.
When the user account control display is
displayed, click “Continue”.
•
•
1
2
1
2
1
2
3
1
2
XXXXXXXXX
1
2
XXXXXXXXX
4
11
Setting up the Projector Network Environment

-14
5Click “Internet Protocol Version 4
(TCP/IPv4)”, and click the
“Properties” button.
6Confirm or change an IP address
for the setup computer.
1Confirm and note the current IP
address, Subnet mask and Default
gateway.
Make sure to note the current IP address,
Subnet mask and Default gateway as you
will be required to reset them later.
2Set temporarily as follows:
IP address: 192.168.150.3
Subnet mask: 255.255.255.0
Default gateway: (Do not input any
values.)
The factory default settings for the projector are
as follows:
DHCP Client: OFF
IP address: 192.168.150.2
Subnet mask: 255.255.255.0
Default gateway: 0.0.0.0
•
Note
7After setting, click the “OK”
button, and then restart the
computer.
5
1
2
1
2
6
7
After confirming or setting, proceed to “3. Setting up Network Connection for the Projector”.
Setting up the Projector Network Environment

-15
3. Setting up a Network Con-
nection for the Projector
Settings for such items as the projector's
IP address and subnet mask are
compatible with the existing network.
Set each item on the projector as follows.
(See page 62 of the projector's operation
manual for setting.)
DHCP Client: Off
IP Address: 192.168.150.002
Subnet Mask: 255.255.255.000
1Start Internet Explorer (version 6.0
or later) on the computer, and
enter “http://192.168.150.2/” in
“Address”, and then press the
“Enter” key.
2If a user name and a password
have not yet been set, just click
the “OK” button.
If a user name and a password have been
set, input the user name and the password,
and click the “OK” button.
If the user name or password is entered
incorrectly three times, an error message will
be displayed.
When you are using Internet Explorer 7 or
later, other setup screen may be displayed. In
this case, make the proper adjustments for
the setup screen.
3When the screen as shown on the
right appears, click “TCP/IP”.
•
•
•
1
2
3
Setting up the Projector Network Environment

-16
4The TCP/IP setting screen
appears, ready for network
settings for the projector.
Items Setting example / Remarks
New
Password
You can set the password to protect
the TCP/IP setting.
DHCP
Client
Select “ON” or “OFF” to determine
whether to use DHCP Client.
IP
Address
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting: 192.168.150.2
Enter an IP address appropriate for
the network.
Subnet
Mask
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting:
255.255.255.0
Set the subnet mask to the same as
that of the computer and equipment
on the network.
Default
Gateway
You can set this item when “DHCP
Client” is set to “OFF”.
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
DNS
Server
Factory default setting: 0.0.0.0
* When not in use, set to “0.0.0.0”.
Confirm the existing network's segment (IP
address group) to avoid setting an IP address
that duplicates the IP addresses of other
network equipment or computers. If
“192.168.150.2” is not used in the network
having an IP address of “192.168.150.XXX”, you
don't have to change the projector IP address.
For details about each setting, consult your
network administrator.
•
•
Note
5Click the “Apply” button.
6The set values appear. Confirm
that the values are set properly,
and then click the “Confirm”
button.
4
5
6
Setting up the Projector Network Environment
Close the browser.
This completes the network settings.
After setting items, wait for about 15 seconds and then re-access.
Change the IP address of the setting computer back to its original address, which you have noted down in
Step 6-1on page 14, and then connect the computer and the projector to the network.
•
•
•
•

-17
Controlling the Projector via LAN
After connecting the projector to your network, enter the projector IP address in
“Address” on Internet Explorer (version 6.0 or later) using a computer on the network to
start a setup screen that will enable control of the projector via the network.
Controlling the Projector
Using Internet Explorer
Complete connections to external
equipment before starting the operation.
(See pages 22-26 of the projector's
operation manual.)
Complete the AC cord connection. (See
page 26 of the projector's operation
manual.)
When connecting the projector to the LAN, use
a commercially available LAN cable (UTP cable,
Category 5, cross-over type). When
connecting the projector to a hub, use a
straight-through cable.
•
Note
1Start Internet Explorer on the
computer.
2Enter “http://” followed by the
projector IP address set by the
procedure on page 16 followed by
“/” in “Address”, and then press
the “Enter” key.
When “DHCP Client” is set to “Off” on the
projector, IP address is 192.168.150.2. If you
did not change the IP address in “3. Setting
up a Network Connection for the
Projector” (pages 15-16), enter
“ ht tp: //19 2.16 8.15 0. 2 / ”.
3A screen for controlling the
projector appears, ready for
performing various status
conditions, control, and settings.
•
1
2
3

-18
Confirming the Projector
Status (Status)
2
1
30
On this screen, you can confirm the
projector status. You can confirm the
following items:
MAC Address
Power
Condition
Lamp Timer
Lamp Life
Input
Signal Info
Serial Number
If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be
displayed. Wait for a moment and then operate
again.
For details about each item, refer to the
projector's operation manual.
•
•
Note
•
•
•
•
•
•
•
•
Controlling the Projector via LAN
Controlling the Projector
(Control)
On this screen, you can perform projector
control. You can control the following
items:
Power
Input Select
Audio Input
Volume
AV Mute
If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be
displayed. Wait for a moment and then operate
again.
You cannot operate this page while the
projector is warming up.
While the projector is in standby mode, you can
only control “Power ON”.
For details about each item, refer to the
projector's operation manual.
•
•
•
•
Note
•
•
•
•
•

-19
Setting and Adjusting the
Projector (Settings & Adjustments)
Example: “Picture” screen display for COMPUTER1
On these screens, you can make projector
settings or adjustments. You can set or
adjust the following items:
Controlling the Projector via LAN
Picture Mode
CLR Temp
BrilliantColorTM
DNR
Eco + Quiet
Resolution Setting
Signal Type
Dynamic Range
Video System
Video Setup
Resize
Overscan
OSD Display
Background
Memory Load
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Projection Mode
Wall Color
OSD Language
Auto Sync
Auto Power Off
Auto Restart
Internal Speaker
Audio Out
RS-232C Speed
Fan Mode
COMPUTER2 Select
DLP®LinkTM
DLP®LinkTM Invert
Rotate Indicator
All Reset
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
If you click the “Refresh” button before the
screen is displayed completely, an error
message (“Server Busy Error”) will be
displayed. Wait for a moment and then operate
again.
You cannot operate this page while the
projector is warming up.
For details about each item, refer to the
projector's operation manual.
•
•
•
Note
Setting the Security
(Network – Security)
On this screen, you can make settings
relating to security.
Items Description
User Name Setting of user name for security
protection.
Password Setting of password for security
protection.
Accept IP
Address
It is possible to set up to three IP
addresses allowing connection to the
projector.
All IP
Addresses
No limits are set to IP addresses
connecting to the projector.
From only
specific IP
addresses
For security improvement, only an IP
address set by “Address 1-3” can be
connected to the projector.
User Name and Password can be up to 8
characters.
You can input the characters below:
a-z, A-Z, 0-9, -, _
•
•
Note

-20
Making General Settings for
the Network (Network - General)
On this screen, you can make general
settings relating to the network.
Items Description
Projector
Name
Setting the projector name.
Auto Logout
Time
Setting the time interval in which the
projector will be automatically
disconnected from the network in units
of a minute (from 1 to 65535 minutes).
If the set value is made 0, the Auto
Logout function is disabled.
Data Port Setting the TCP port number used
when exchanging data with the
projector (from 1025 to 65535).
Search Port Setting the port number used when
searching for the projector (from 1025
to 65535).
After clicking the “Apply” button, the set
values appear. Confirm that the values are
set properly, and then click the “Confirm”
button.
After setting items, wait for about 15 seconds
and then re-access.
Projector Name can be up to 12 characters.
You can input the characters below:
A-Z, 0-9, -, _, (,), space
(When “a-z” are input, they are converted to
“A-Z” automatically.)
•
•
•
Note
Setting for Sending E-mail
when an Error Occurs
(Mail – Originator Settings)
On this screen, you can make settings for
sending e-mail to report when the
projector has generated an error.
Items Setting example / Remarks
SMTP Server Setting an SMTP server address for e-
mail transmission.
e.g.1: 192.168.150.253
e.g.2: smtp123.sharp.co.jp
* When using a domain name, make
settings for the DNS server.
Originator E-
mail Address
Setting the projector's e-mail address.
The e-mail address set here becomes
Originator E-mail Address.
Originator
Name
Setting the sender's name. The name
set here appears in the “Originator
Name” column of the body of the
message.
SMTP Server, Originator E-mail Address and
Originator Name can be up to 64 characters.
You can input the characters below:
SMTP Server and Originator E-mail Address:
a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, },
~, _, ', ., @, `
(You can input “@” only one time for “Originator
E-mail Address”.)
Originator Name : a-z, A-Z, 0-9, -, _, (,), space
If the settings of “3. Setting up a Network
Connection for the Projector” on pages 15
and 16 are incorrectly set, e-mail will not be
sent.
•
•
•
Note
Controlling the Projector via LAN