Sharp XV-Z30000 Operation User guide

MODEL
XV-Z30000
PROJECTOR
SETUP MANUAL
Connecting Pin Assignments ............................................................ 2
RS-232C Specifications and Commands ......................................... 4
Setting up the Projector Network Environment ................................. 8
1. Connecting the Projector to a Computer .............................................. 9
2. Setting an IP Address for the Computer ............................................. 10
3. Setting the Projector Using Internet Explorer...................................... 12
Resetting the Lamp Timer of the Projector via LAN ..................... 13
Troubleshooting................................................................................ 15

-2
Connecting Pin Assignments
COMPUTER/COMPONENT input Terminal: mini D-sub 15 pin female connector
COMPUTER Input COMPONENT Input
Pin No. Signal Pin No. Signal
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Video input (red)
Video input (green/sync on green)
Video input (blue)
Not connected
Not connected
Earth (red)
Earth (green/sync on green)
Earth (blue)
Not connected
GND
Not connected
Bi-directional data
Horizontal sync signal: TTL level
Vertical sync signal: TTL level
Data clock
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
PR (CR)
Y
PB (CB)
Not connected
Not connected
Earth (PR)
Earth (Y)
Earth (PB)
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
HDMI Terminal
Pin No. Name Pin No. Name
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
T.M.D.S. Da ta 2+
T.M.D.S. Data 2 Shield
T.M.D.S. Data 2–
T.M.D.S. Da ta 1+
T.M.D.S. Data 1 Shield
T.M.D.S. Da ta 1–
T.M.D.S. Da ta 0+
T.M.D.S. Data 0 Shield
T.M.D.S. Da ta 0 –
T.M.D.S. Cl ock+
11.
12.
13.
14.
15.
16.
17.
18.
19.
T.M.D.S. Clock Shield
T.M.D.S. Cl ock–
CEC
Utility
SCL
SDA
DDC/CEC ground
+5V power
Hot plug detection
RS-232C Terminal: D-sub 9 pin male connector of the DIN-D-sub RS-232C adaptor
Pin No. Signal Name I/O Reference
1.
2.
3.
4.
5.
6.
7.
8.
9.
RD
SD
SG
RS
CS
Receive Data
Send Data
Signal Ground
Request to Send
Clear to Send
Input
Output
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
5
10
15
1
11
6
5
10
15
1
11
6
218
19 1
218
19 1
15
69
15
69

-3
RS-232C Cable recommended connection: D-sub 9 pin female connector
Pin No. Signal Pin No. Signal
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
Projector
Pin No.
Computer
Pin No.
4
5
6
4
5
6
LAN Terminal: LAN (RJ-45)
Pin No. Signal Pin No. Signal
1.
2.
3.
4.
TX+
TX–
RX+
5.
6.
7.
8.
RX–
51
96
51
96
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
•
Note
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
•
Note
8... 18 ... 1
Connecting Pin Assignments

-4
RS-232C Specifications and Commands
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross
type, commercially available) to the projector. (See page 26 of the projector's operation manual for
connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard. Parity bit: None
Baud rate*: 9,600 bps Stop bit: 1 bit
Data length: 8 bits Flow control: None
*Set the projector's baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code.
After the projector processes the command from the computer, it sends a response code to the
computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4 Return code (0DH)
Command 4-digit Parameter 4-digit
Response code format
Normal response
Problem response (communication error or incorrect command)
OK Return code (0DH) E R R Return code (0DH)
Info
When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds
after the power has been turned on, and then transmit the commands.
After sending an input selection or picture adjustment command and then receiving an “OK” response
code, the projector may take some time to process the command. If a second command is sent while the
projector is still processing the first command, you may receive an “ERR” response code. If this happens,
try resending the second command.
When more than one code is being sent, send each command only after the response code for the
previous command from the projector is verified.
“POWR????”, “TABN _ _ _ 1”, “TLPS _ _ _ 1”, “TPOW _ _ _ 1”, “TLPN _ _ _ 1”, “TLTT _ _ _ 1”,
“TLTM _ _ _ 1”, “TLTL _ _ _ 1”, “TNAM _ _ _ 1”, “MNRD _ _ _ 1”, “PJN0 _ _ _ 1”
− When the projector receives the special commands shown above:
* The on-screen display will not disappear.
* The “Auto Power Off” or “No Operation Off” timer will not be reset.
− The special commands are available for applications that require continuous polling.
•
•
•
•
If an underbar (_) appears in the parameter column, enter a space.
If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets under
Control Contents.
•
•
Note

-5
Commands
Example: When turning on the projector, make the following setting.
Computer Projector
POWR___1
o
m
OK
Control Contents Command Parameter
Return
Power ON Standby mode
(or 30-second startup time)
Power On P O W R _ _ _ 1 OK or ERR OK
Off P O W R _ _ _ 0 OK OK or ERR
Status P O W R ???? 10
Projector Condition T A B N _ _ _ 1 0: Normal
1: Temp High
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
0: Normal
1: Temp High
2: Fan Error
4: Lamp Cover Open
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
64: Temp Abnormally High
Lamp Status T L P S _ _ _ 1 0: Off, 1: On, 2: Retry
3: Waiting, 4: Lamp Error
0: Off, 4: Lamp Error
Power Status T P O W _ _ _ 1 1: On, 2: Cooling 0: Standby
Quantity T L P N _ _ _ 1 1
Usage Time (Hour) T L T T _ _ _ 1 0-9999 (Integer)
Usage Time (Minuite) T L T M _ _ _ 1 0, 15, 30, 45
Life (Percentage) T L T L _ _ _ 1 0%-100% (Integer)
Name Model Name Check T N A M _ _ _ 1 XVZ30000
Model Name Check M N R D _ _ _ 1 XV-Z30000
Projector Name Setting1 (First 4 characters) *1 P J N 1 * * * * OK or ERR
Projector Name Setting2 (Middle 4 characters) *1 P J N 2 * * * * OK or ERR
Projector Name Setting3 (Last 4 characters) *1 P J N 3 * * * * OK or ERR
Projector Name Check P J N 0 _ _ _ 1 Projector Name
Input Change COMPUTER I R G B _ _ _ 1 OK or ERR ERR
COMPONENT I R G B _ _ _ 2 OK or ERR ERR
HDMI1 I R G B _ _ _ 3 OK or ERR ERR
HDMI2 I R G B _ _ _ 4 OK or ERR ERR
Input RGB Check I R G B ? ? ? ? 1: COMPUTER, 2: COMPONENT,
3: HDMI1, 4: HDMI2, ERR
ERR
Input Mode Check I M O D ? ? ? ? 1: RGB ERR
Input Check I C H K ? ? ? ? 1: COMPUTER
2: COMPONENT
3: HDMI1
4: HDMI2
ERR
Resize COMPUTER Normal R A S R _ _ _ 1 OK or ERR ERR
16:9 R A S R _ _ _ 2 OK or ERR ERR
Native R A S R _ _ _ 3 OK or ERR ERR
Cinema Zoom R A S R _ _ _ 5 OK or ERR ERR
Zoom14:9 R A S R _ _ _ 7 OK or ERR ERR
Smart Zoom R A S R _ _ _ 6 OK or ERR ERR
COMPONENT Normal R B S R _ _ _ 1 OK or ERR ERR
16:9 R B S R _ _ _ 2 OK or ERR ERR
Native R B S R _ _ _ 3 OK or ERR ERR
Cinema Zoom R B S R _ _ _ 5 OK or ERR ERR
Zoom14:9 R B S R _ _ _ 7 OK or ERR ERR
Smart Zoom R B S R _ _ _ 6 OK or ERR ERR
HDMI1 Normal R C S R _ _ _ 1 OK or ERR ERR
16:9 R C S R _ _ _ 2 OK or ERR ERR
Native R C S R _ _ _ 3 OK or ERR ERR
Cinema Zoom R C S R _ _ _ 5 OK or ERR ERR
Zoom14:9 R C S R _ _ _ 7 OK or ERR ERR
Smart Zoom R C S R _ _ _ 6 OK or ERR ERR
HDMI2 Normal R D S R _ _ _ 1 OK or ERR ERR
16:9 R D S R _ _ _ 2 OK or ERR ERR
Native R D S R _ _ _ 3 OK or ERR ERR
Cinema Zoom R D S R _ _ _ 5 OK or ERR ERR
Zoom14:9 R D S R _ _ _ 7 OK or ERR ERR
Smart Zoom R D S R _ _ _ 6 OK or ERR ERR
ALL Reset A L R E _ _ _ 1 OK or ERR ERR
RS-232C Specifications and Commands

-6
Control Contents Command Parameter
Return
Power ON Standby mode
(or 30-second startup time)
COMPUTER INPUT Picture Mode Standard R A P S _ _ _ 1 OK or ERR ERR
Movie1 R A P S _ _ _ 2 OK or ERR ERR
Movie2 R A P S _ _ _ 3 OK or ERR ERR
Monochrome R A P S _ _ _ 4 OK or ERR ERR
Anime R A P S _ _ _ 5 OK or ERR ERR
Sports R A P S _ _ _ 6 OK or ERR ERR
Stage R A P S _ _ _ 7 OK or ERR ERR
Dynamic R A P S _ _ _ 8 OK or ERR ERR
User1 R A P S _ _ _ 9 OK or ERR ERR
User2 R A P S _ _ 1 0 OK or ERR ERR
Game R A P S _ _ 1 1 OK or ERR ERR
Contrast -30 - +30 R A P I _ * * * OK or ERR ERR
Bright -30 - +30 R A B R _ * * * OK or ERR ERR
Color -30 - +30 R A C O _ * * * OK or ERR ERR
Tint -30 - +30 R A T I _ * * * OK or ERR ERR
Sharp -30 - +30 R A S H _ * * * OK or ERR ERR
Red Gain -30 - +30 R A R D _ * * * OK or ERR ERR
Green Gain -30 - +30 R A G N _ * * * OK or ERR ERR
Blue Gain -30 - +30 R A B E _ * * * OK or ERR ERR
CLR Temp -2 - +2 R A C T _ _ * * OK or ERR ERR
Picture Reset R A R E _ _ _ 1 OK or ERR ERR
COMPONENT INPUT Picture Mode Standard R B P S _ _ _ 1 OK or ERR ERR
Movie1 R B P S _ _ _ 2 OK or ERR ERR
Movie2 R B P S _ _ _ 3 OK or ERR ERR
Monochrome R B P S _ _ _ 4 OK or ERR ERR
Anime R B P S _ _ _ 5 OK or ERR ERR
Sports R B P S _ _ _ 6 OK or ERR ERR
Stage R B P S _ _ _ 7 OK or ERR ERR
Dynamic R B P S _ _ _ 8 OK or ERR ERR
User1 R B P S _ _ _ 9 OK or ERR ERR
User2 R B P S _ _ 1 0 OK or ERR ERR
Game R B P S _ _ 1 1 OK or ERR ERR
Contrast -30 - +30 R BP I _ * * * OK or ERR ERR
Bright -30 - +30 R BB R _ * * * OK or ERR ERR
Color -30 - +30 R BC O _ * * * OK or ERR ERR
Tint -30 - +30 R BT I _ * * * OK or ERR ERR
Sharp -30 - +30 R BS H _ * * * OK or ERR ERR
Red Gain -30 - +30 R BRD_ * * *
OK or ERR ERR
Green Gain -30 - +30 R B G N _ * * * OK or ERR ERR
Blue Gain -30 - +30 R BBE_* * *
OK or ERR ERR
CLR Temp -2 - +2 R BCT__* *
OK or ERR ERR
Picture Reset R B R E _ _ _ 1 OK or ERR ERR
HDMI1 Picture Mode Standard R C P S _ _ _ 1 OK or ERR ERR
Movie1 R C P S _ _ _ 2 OK or ERR ERR
Movie2 R C P S _ _ _ 3 OK or ERR ERR
Monochrome R C P S _ _ _ 4 OK or ERR ERR
Anime R C P S _ _ _ 5 OK or ERR ERR
Sports R C P S _ _ _ 6 OK or ERR ERR
Stage R C P S _ _ _ 7 OK or ERR ERR
Dynamic R C P S _ _ _ 8 OK or ERR ERR
User1 R C P S _ _ _ 9 OK or ERR ERR
User2 R C P S _ _ 1 0 OK or ERR ERR
Game R C P S _ _ 1 1 OK or ERR ERR
Contrast -30 - +30 R C P I _ * * * OK or ERR ERR
Bright -30 - +30 R C B R _ * * * OK or ERR ERR
Color -30 - +30 R C C O _ * * * OK or ERR ERR
Tint -30 - +30 R C T I _ * * * OK or ERR ERR
Sharp -30 - +30 R C S H _ * * * OK or ERR ERR
Red Gain -30 - +30 R C R D _ * * * OK or ERR ERR
Green Gain -30 - +30 R C G N _ * * * OK or ERR ERR
Blue Gain -30 - +30 R C B E _ * * * OK or ERR ERR
CLR Temp -2 - +2 R C C T _ _ * * OK or ERR ERR
Picture Reset R C R E _ _ _ 1 OK or ERR ERR
RS-232C Specifications and Commands

-7
Control Contents Command Parameter
Return
Power ON Standby mode
(or 30-second startup time)
HDMI2 Picture Mode Standard R D P S _ _ _ 1 OK or ERR ERR
Movie1 R D P S _ _ _ 2 OK or ERR ERR
Movie2 R D P S _ _ _ 3 OK or ERR ERR
Monochrome R D P S _ _ _ 4 OK or ERR ERR
Anime R D P S _ _ _ 5 OK or ERR ERR
Sports R D P S _ _ _ 6 OK or ERR ERR
Stage R D P S _ _ _ 7 OK or ERR ERR
Dynamic R D P S _ _ _ 8 OK or ERR ERR
User1 R D P S _ _ _ 9 OK or ERR ERR
User2 R D P S _ _ 1 0 OK or ERR ERR
Game R D P S _ _ 1 1 OK or ERR ERR
Contrast -30 - +30 R D P I _ * * * OK or ERR ERR
Bright -30 - +30 R D B R _ * * * OK or ERR ERR
Color -30 - +30 R D C O _ * * * OK or ERR ERR
Tint -30 - +30 R D T I _ * * * OK or ERR ERR
Sharp -30 - +30 R D S H _ * * * OK or ERR ERR
Red Gain -30 - +30 R D R D _ * * * OK or ERR ERR
Green Gain -30 - +30 R D G N _ * * * OK or ERR ERR
Blue Gain -30 - +30 R D B E _ * * * OK or ERR ERR
CLR Temp -2 - +2 R D C T _ _ * * OK or ERR ERR
Picture Reset R D R E _ _ _ 1 OK or ERR ERR
RGB Frequency Check Horizontal T F R Q _ _ _ 1 kHz (***.* or ERR) ERR
Vertical T F R Q _ _ _ 2 Hz (***.* or ERR) ERR
3D On 3 D E N _ _ _ 1 OK or ERR ERR
Off 3 D E N _ _ _ 0 OK or ERR ERR
Format Auto 3 D F M _ _ _ 0 OK or ERR ERR
Side By Side 3 D F M _ _ _ 1 OK or ERR ERR
Top And Bottom 3 D F M _ _ _ 2 OK or ERR ERR
Invert 3 D I V _ _ _ 1 OK or ERR ERR
ANAMORPHIC Off A N A M _ _ _ 0 OK or ERR ERR
2.35:1 A N A M _ _ _ 1 OK or ERR ERR
16:9 A N A M _ _ _ 2 OK or ERR ERR
LENS Focus -255 - 255 L N F O * * * * OK or ERR ERR
Zoom -255 - +255 L N Z O * * * * OK or ERR ERR
Vertical Lens Shift *3 -800 - +800 L N S H * * * * OK or ERR ERR
-800 - +800 L N U D * * * * OK or ERR ERR
Horizontal Lens Shift *3 -800 - +800 L N L R * * * * OK or ERR ERR
Lens Shift Center *3 L N P D _ _ _ 1 OK or ERR ERR
MEMORY Save 1-2 L N S V * * * * OK or ERR ERR
Load *3 1-2 L N L O * * * * OK or ERR ERR
Clear 1-2 L N C R * * * * OK or ERR ERR
Lock Off L N M L _ _ _ 0 OK or ERR ERR
On L N M L _ _ _ 1 OK or ERR ERR
Reset Network Setting L N R E _ _ _ 1 OK or ERR OK or ERR
Restart Network L R E S _ _ _ 1 OK or ERR OK or ERR
Lamp Timer Reset *2 L P R E 0 0 0 1 ERR OK, ERR
*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.
*2 The Lamp Timer Reset command can only be sent in standby mode.
*3 If the lens cover is not correctly attached, you may receive an “ERR” response code.
RS-232C Specifications and Commands

-8
Setting up the Projector Network Environment
This section describes the basic procedure for using the projector via the network.
If the network is already constructed, the projector's network settings may need to be
changed. Please consult your network administrator for assistance with these settings.
You can make network settings both on the projector and on the computer. The following
procedure is for making settings on the computer.
Network settings on the computer
Connect a LAN cable (Category 5, cross-over type) between the computer and projector.
LAN cable
(commercially available)
1. Connecting the projector to a computer
Page 9
Adjust the IP settings of the computer to enable one-to-one communications with the projector.
Temporarily change
the computer's IP
address.
2. Setting an IP address for the computer
Pages 10, 11
Adjust the projector network settings to conform to your network.
Use Internet Explorer
(version 6.0 or later)
to make various
projector settings.
3. Setting the Projector Using Internet Explorer
Page 12
Microsoft®, Windows®, Windows®XP, Windows Vista®and Windows®7 are registered trademarks of
Microsoft Corporation in the United States and/or other countries.
All other company or product names are trademarks or registered trademarks of their respective
companies.
•
•

-9
1. Connecting the Projector
to a Computer
Establishing a one-to-one connection from
the projector to a computer. Using a
commercially available LAN cable (UTP
cable, Category 5, cross-over type) you can
configure the projector via the computer.
1
Disconnect the computer's LAN
cable from the existing network.
2Connect a commercially available
LAN cable (UTP cable, Category 5,
cross-over type) to the projector's
LAN terminal and connect the
other end of the cable to the
computer's LAN terminal.
3Plug the power cord into the AC
socket of the projector.
4Turn on the computer.
Info
Confirm that the LINK LED on the rear of the
projector illuminates. If the LINK LED does not
illuminate, check the following:
The LAN cable is properly connected.
The power switches of both the projector and
the computer are on.
•
•
1
A LAN cable being
connected to the network
A LAN cable being
connected to the network
2
LAN cable
(cross-over type, commercially available)
LAN cable
(cross-over type, commercially available)
3
4
ONON
Setting up the Projector Network Environment
This completes the connection. Now proceed to “2. Setting an IP Address for the Computer”.

-10
2. Setting an IP Address for
the Computer
The following describes how to make
settings in Windows Vista®.
1Log on the network using the
administrator's account for the
computer.
2Click “start”, and click “Control
Panel”.
3Click “View network status and
tasks” of “Network and Internet”,
and click “View status” in the new
window.
This manual uses examples to explain the
operations in Category View. If you are using
Classic View, double-click “Network and
Sharing Center”.
4Click “Properties”.
When the user account control display is
displayed, click “Continue”.
•
•
1
2
1
2
1
2
3
1
2
XXXXXXXXX
1
2
XXXXXXXXX
4
11
Setting up the Projector Network Environment

-11
Setting up the Projector Network Environment
5Click “Internet Protocol Version 4
(TCP/IPv4)”, and click the
“Properties” button.
6Confirm or change an IP address
for the setup computer.
1Confirm and note the current IP
address, Subnet mask and Default
gateway.
Make sure to note the current IP address,
Subnet mask and Default gateway as you
will be required to reset them later.
2Set temporarily as follows:
IP address: 192.168.150.3
Subnet mask: 255.255.255.0
Default gateway: (Do not input any
values.)
The factory default settings for the projector are
as follows:
DHCP Client: OFF
IP address: 192.168.150.2
Subnet mask: 255.255.255.0
Default gateway: 0.0.0.0
•
Note
7After setting, click the “OK”
button, and then restart the
computer.
5
1
2
1
2
6
7
After confirming or setting, proceed to “3. Setting the Projector Using Internet Explorer”.

-12
3. Setting the Projector
Using Internet Explorer
Complete connections to external
equipment before starting the operation.
(See pages 23-27 of the projector's
operation manual.)
Complete the AC cord connection. (See
page 27 of the projector's operation
manual.)
Setting up the Projector Network Environment
When connecting the projector to the LAN, use
a commercially available LAN cable (UTP cable,
Category 5, cross-over type). When connecting
the projector to a hub, use a straight-through
cable.
•
Note
1Start Internet Explorer (version 6.0
or later) on the computer, and
enter “http://192.168.150.2/” in
“Address”, and then press the
“Enter” key.
1
2A screen for setting the projector
appears, set the each item.
Items Description
User Name Setting of user name for security
protection.
Password Setting of password for security
protection.
Projector
Name
Setting the projector name.
Auto Logout
Time
Setting the time interval in which
the projector will be automatically
disconnected from the network
in units of a minute (from 1 to
65535 minutes). If the set value is
made 0, the Auto Logout function
is disabled.
Data Port Setting the TCP port number
used when exchanging data with
the projector (from 1025 to
65535).
Search Port Setting the port number used
when searching for the projector
(from 1025 to 65535).
2
You can change the projector's IP address in
“TCP/IP” of the “Network” menu on the
projector.
•
Note
After setting items, wait for about 15 seconds
and then re-access.
User Name and Password can be up to 8
characters.
Projector Name can be up to 12 characters.
You can input the characters below:
a-z, A-Z, 0-9, -, _, (,), space
•
•
•
•
Note

-13
Resetting the Lamp Timer of the Projector via LAN
When the projector is connected to a network, you can use the communications program
to send a command to reset the lamp timer. The example below uses Windows®XP as the
operating system. When you use Windows Vista®or Windows®7, use other communications
program referring to the following steps, because Windows Vista®or Windows®7 does not
come with HyperTerminal.
1Click “Start” – “All Programs” –
“Accessories” – “Communica-
tions” – “HyperTerminal”.
If you do not have HyperTerminal installed,
see the operation manual of your computer.
Depending on the settings of your computer,
you may be required to enter your area code
and other details. Enter the information as
required.
2Enter a name in the “Name” field,
and click “OK”.
3If you are required to enter the
area code, enter it in the “Area
code” field. From the “Connect
using” drop-down menu, select
“TCP/IP (Winsock)”, and click
“OK”.
4Enter the IP address of the
projector in the “Host address”
field (see “TCP/IP” on the
“Network” menu of the projector),
and enter the data port of the
projector in the “Port number”
field (“10002” is the factory default
setting), and click “OK”.
•
•
1
2
3
Select
“TCP/IP (Winsock)”
Select
“TCP/IP (Winsock)”
4

-14
5Click “Properties” on the “File”
menu.
6Click the “Settings” tab, and then
click “ASCII Setup”.
7Select the check boxes next to
“Send line ends with line feeds”,
“Echo typed characters locally”,
and “Append line feeds to
incoming line ends”, and click
“OK”.
The LAMPRESET Properties window
appears, click “OK”.
8If a user name and/or password is
set for the projector, enter the
user name and password.
9Send the lamp reset command
“LPRE0001”.
This command can only be sent when the
projector is in standby mode.
When “OK” is received, this indicates that the
lamp was successfully reset.
10
Close HyperTerminal.
•
•
•
5
6
7
8
9
1
0
Resetting the Lamp Timer of the Projector via LAN

-15
Troubleshooting
Communication cannot be established with the projector
When connecting the projector using serial-connection
?Check that the RS-232C terminal of the projector and a computer or the commercially
available controller are connected correctly.
?Check that the RS-232C cable is a cross-over cable.
?Check that the RS-232C port setting for the projector corresponds to the setting for the
computer or the commercially available controller.
When connecting the projector to a computer using network (LAN)-
connection
?Check that the cable's connector is firmly inserted in the LAN terminal of the projector.
?Check that the cable is firmly inserted into a LAN port for a computer or a network device
such as a hub.
?Check that the LAN cable is a Category 5 cable.
?Check that the LAN cable is a cross-over cable when connecting the projector to a computer
directly.
?Check that the LAN cable is a straight-through cable when connecting the projector with a
network device such as a hub.
?Check that the power supply is turned on for the network device such as a hub between the
projector and a computer.
?If all of the above are unsuccessful, restart the network function using “Network” - “Restart
Network”. (See page 59 of the projector’s operation manual.)
Check the network settings for the computer and the projector
?Check the following network settings for the projector.
IP Address
Check that the IP address for the projector is not duplicated on the network.
Subnet Mask
When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting
for the projector and the default gateway setting for the computer are the same:
The subnet masks for the projector and the computer should be the same.
The IP address parts shown by the subnet mask for the projector and the computer
should be the same.
(Example)
When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the
projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the
subnet mask should be “255.255.255.0”.
Gateway
When the gateway setting for the projector is “0.0.0.0” (Not Used), or the gateway setting
for the projector and the default gateway setting for the computer are the same:
The subnets for the projector and the computer should be the same.
The IP address parts shown by the subnet mask for the projector and the computer
should be the same.
(Example)
When the IP address is “192.168.150.2” and the subnet mask is “255.255.255.0” for the
projector, the IP address for the computer should be “192.168.150.X” (X=3-254) and the
subnet mask should be “255.255.255.0”.
When “DHCP Client” is set to “Off” on the projector:
IP address: 192.168.150.2
Subnet mask: 255.255.255.0
Gateway address: 0.0.0.0 (Not Used)
For network settings for the projector, refer to page 12.
•
•
Note
•
•
•
•
•
•
•

-16
?Take the following steps for checking the network settings for the computer.
1. Open a command prompt.
Click “start” ➔“All Programs” ➔“Accessories” ➔“Command Prompt” in order.
2. After launching the command prompt, enter the command “ipconfig”, and press the “Enter”
key.
Communication may not be established even after carrying out the network settings
for the computer. In such cases, restart your computer.
•
Note
C:\>ipconfig
Usage examples of ipconfig
C:\>ipconfig /? displays how to use “ipconfig.exe”.
C:\>ipconfig displays the set IP address, subnet mask and default gateway.
C:\>ipconfig /all displays all the setting information related to TCP/IP.
•
Note
3. To return to the Windows®screen, enter “exit” and press the “Enter” key.
Troubleshooting

-17
?Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also, check
if an IP address is set.
1. Open a command prompt.
Click “start” ➔“All Programs” ➔“Accessories” ➔“Command Prompt” in order.
2. After launching the command prompt enter a command “PING”.
Entry example C:\>ping XXX.XXX.XXX.XXX
“XXX.XXX.XXX.XXX” should be entered with an IP address to be connected to, such as the
projector.
3. When connecting normally, the display will be as follows.
(The screen may be slightly different depending on the OS type.)
<Example> when the IP address connected to is “192.168.150.1”
4. When a command cannot be sent, “Request time out” will be displayed.
Check the network setting again.
If communication can still not be established properly, contact your network administrator.
5. To return to the Windows®screen, enter “exit” and then press the “Enter” key.
?When the projector cannot be connected, even though the “PING” command is checked:
1. When a security software is installed on the PC, or when a fire wall has been set up for the
network system, connection may not be possible. Consult the system administrator when,
for example, you want to change the settings to enable use of the TCP port set as the data
port.
2. When neither of the above two items applies, change the settings for the data port.
A connection cannot be made because you have forgotten your user name
or your password.
?Initialize the settings. (See page 59 of the projector's operation manual.)
?After the initialization, carry out setting again.
Troubleshooting