Sharp 21V-FS700S User manual

CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS...................................... 1-1
CHAPTER 2. IMPORTANT SERVICE NOTES
[1] IMPORTANT SERVICE NOTES ................ 2-1
CHAPTER 3. ADJUSTMENT PRECAUTIONS
[1] ADJUSTMENT PRECAUTIONS ................ 3-1
[2] ADJUSTMENT ........................................... 3-13
CHAPTER 5. TROUBLE SHOOTING FLOWCHART
[1] TROUBLE SHOOTING FLOWCHART ...... 5-1
CHAPTER 6. SOLID STATE DEVICE BASE DIAGRAM
[1] SOLID STATE DEVICE BASE DIAGRAM.. 6-1
CHAPTER 7. CHASSIS LAYOUT
[1] CHASSIS LAYOUT .................................... 7-1
CHAPTER 8. BLOCK DIAGRAM
[1] BLOCK DIAGRAM : MAIN UNIT............... 8-1
[2] BLOCK DIAGRAM : CRT UNIT............... 8-3
CHAPTER 9. DESCRIPTION OF SCHEMATIC DIA-
GRAM
[1] DESCRIPTION OF SCHEMATIC DIA-
GRAM...................................................... 9-1
CHAPTER 10. WAVEFORMS
[1] WAVEFORMS....................................... 10-1
CHAPTER 11. SCHEMATIC DIAGRAM
[1] SCHEMATIC DIAGRAM : CRT UNIT..... 11-1
[2] SCHEMATIC DIAGRAM : MAIN UNIT.... 11-2
CHAPTER 12. PRINTED WIRING BOARD ASSEM-
BLIES
[1] PWB-A : MAIN UNIT............................... 12-1
[2] PWB-B : CRT UNIT................................ 12-3
Parts Guide
SERVICE MANUAL
xxxxxxxxx
TopPage
21V-FS700S
No. S6810121VFS700S
COLOUR TELEVISION
Chassis No.GA-7S
MODEL
Auto Fine Tuning
High Contrast Picture (Black Stretch
Circuit)
Stereo
Multi Languages OSD
(English/Spanish)
 5 Band Graphic Equalizer
 Front AV IN & Rear AV IN / OUT
Terminals
 AV Mode (3 Mode)
FEATURES
NTSC
Frequency Synthesizer Tuner
Full Auto System
100-CH Program Memory
CATV (Hyper Band Ready)
Hotel Mode
White Temperature Select
Off Timer
Blue Back Function
Aperture Control Circuit
 Child Lock
 Component In
AVL Function
Bass+
M.P-In Jack
Picture Noise Reduction Function
Closed Caption
Surround
EZ Setup
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and
only parts identical to those specified should be used.
CONTENTS
The chassis in this receiver is partially hot. Use an isolation transformer between the line cord plug and power receptacle, when servicing
this chassis. To prevent electric shock, do not remove cover. No user-serviceable parts inside. Refer servicing to qualified service personnel.
WARNING
21V-FS700S
CHAPTER 4. MEMORY MAP
[1] MEMORY MAP.............................................4-1

21V-FS700S
1 – 1
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS
Convergence ................................................................................................................ Self Convergence System
Focus
.......................................................................................................................
Electro-Static Focusing
Sweep Deflection ................................................................................................................................... Magnetic
Intermediate Frequencies
Picture IF Carrier ............................................................................................................................... 45.75MHz
Sound IF Carrier Frequency ............................................................................................................ 41.25MHz
Colour Sub-Carrier Frequency............................................................................................................ 42.17MHz
Cabinet material .................................................................................................................................... All Plastics
Specifications are subject to change without prior notice
Aerial Input Impedance
VHF/UHF ........................................................................................................................ 75 ohms Unbalanced
Receiving System ....................................................................................................................................... NTSC
Receiving Channel
VHF-Channels ................................................................................................................................. 2 thru 13
UHF-Channels ................................................................................................................................. 14 thru 69
Power Input .................................................................................................................... 110 ~ 240V AC 50/60 Hz
Power Consumption..................................................................................................................................... 105W
Audio Power Output Rating .............................................................................................................. 3W(rms) x 4
Voice Coil Impedance ........................................................................................................... 32 ohms at 400 Hz
.............................................................................................................................
Speaker
9 x 5 cm Elliptic (4 pcs)
Size
Dimensions ..................................................................................................................................... Width: 577mm
Height: 467mm
Depth: 340mm
Weight(approx): 20 kg
CATV-Channels ................................................................................................................................ 1 thru 125

21V-FS700S
2 – 1
TV21V-FS700SService Manual21V-FS700SMarketE
CHAPTER 2. IMPORTANT SERVICE NOTES
[1] IMPORTANT SERVICE NOTES
Maintenance and repair of this receiver should be done by qualified service personnel only.
1. SERVICE OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE
When servicing the high voltage system, remove static charge from it by connecting a 10K ohm resistor in series with an insulated wire (such as a test
probe) between picture tube dag and 2nd anode lead. (AC line cord should be disconnected from AC outlet.)
1) Picture tube in this receiver employs integral implosion protection.
2) Replace with the same type number of picture tube for continued safety.
3) Do not lift picture tube by the neck.
4) Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage completely.
2. X-RAY
This receiver is designed so that any X-Ray radiation is kept to an absolute minimum. Since certain malfunctions or servicing may produce potentially
hazardous radiation with prolonged exposure at close range, the following precautions should be observed:
1) When repairing the circuit, please make sure do not increase the high voltage of the set to more than 26.0kV (at beam 0µA).
2) To keep the set in a normal operation, please make sure it’s function at 23.0kV ±1.0kV (at beam 1000µA). The set has been factory - adjusted to
the above-mentioned high voltage.
*If there is a possibility that the high voltage fluctuates as a result of the repairs, never forget to check for such high voltage after the work.
3) Do not substitute a picture tube with unauthorizerd types and/or brands which may cause excessive X-ray radiation.
3. BEFORE RETURNING THE RECEIVER
Before returning the receiver to the user, perform the following safety checks.
1) Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the
receiver.
2) Inspect all protective devices such as non-metal control knobs, insulating materials, cabinet backs, adjustment and compartment covers or
shields, isolation resistor-capacity networks, mechanical insulators etc.

21V-FS700S
3 – 1
TV21V-FS700SService Manual21V-FS700SMarketE
CHAPTER 3. ADJUSTMENT PRECAUTIONS
[1] ADJUSTMENT PRECAUTIONS
This model's setting are adjusted in two different ways: through the I2C bus control and in the
conventional analog manner. The adjustments via the I2C bus control include preset-only items and
variable data.
1. Setting the service mode by the microprocessor.
(1). Press and hold the local key "VOL DOWN" & "CH UP" when power on the main switch,
TV will enter into the SERVICE MODE in Adjustment Mode. (The initial value of EEPROM
are automatically preset when new EEPROM is used).
Service Mode also can be reached by pressing "Service" key (code: 40 Hex)
(2). Press the CH DOWN / UP key on the remote controller to select the items
one by one in Adjustment Mode.
(3). Using the VOLUME UP/ DOWN key on the remote controller, the data can be modified.
(4). When press the local key "VOL DOWN" & "CH UP" at the same time,
it will be released from the service mode.
(5) Press the MENU key on the remote controller to enter into NVM mode.
Press MENU key again to leave the NVM mode return to Adjustment Mode.
(Not recommended to modify the data unless as listed in BUS SETUP data)
(6) Press both CH-UP and VOL-DOWN buttons on the TV set simutaneously or press
the "SERVICE" (40HEX) key again, it will switch to the NORMAL mode position, and
the microprocessor is out of the SERVICE mode.
2. Factory Presetting.
(1). Press remote controller key of code "ED" for 4 seconds, the initial values are
automatically preset.
(2). The initial data are preset as listed in page 5~8.
(3). Make sure whether the data need to modify or not (Initial data).
(Refer to BUS SETUP DATA)
Note: Once the chassis has been assembly together and in ready condition, please make
sure it's go through initialize process (see sect 2 above)
Precaution: If haven't done this initialization, malfunction might be happen.

21V-FS700S
3 – 2
ADJUSTMENT ITEM
***Below are the adjustment items that should be done, PLS FOLLOW THE
PROCEDURE. Otherwise some adjustment items will not be accurate.
NO *** REVISION
1 BUS SET UP
2RF-AGC
3 FOCUS ADJ
4V-SLOPE
5V-SHIFT60
6 V-AMP-60
7V-LIN
8SCOR
9 H-SHI-60
10 EW-W-60
11 E/W-PAR-60
12 UPCOR-PAR
13 LOCOR-PAR
14 H-BOW
15 H-PAR
16 EW-TRAP
17 V-SHIFT50
18 V-AMP-50
19 H-SHIFT-50
20 EW-W-50
21 E/W-PAR-50
22 SCREEN
23 WHITE BALANCE
24 SUB-BRIGHTNESS
25 SUB-CONTRAST
26 BEAM CURRENT CHECK
27 SUB-COLOR
28 SUB-TINT
29 HV PROTECTOR CHECK
30 OTHER PROTECTOR CHECK
31 AV OUT CHECK
32 AV IN CHECK
33 COMPONENT IN CHECK
34 PICTURE CONTROL CHECK
35 COLOR CONTROL CHECK
36 BRIGHTNESS CONTROL CHECK
37 TINT CONTROL CHECK
38 SHARPNESS CONTROL CHECK
39 CH DISPLAY COLOR CHECK
40 SURROUND CHECK
41 BALANCE CHECK
42 BASS+ CHECK
43 EQUALIZER CHECK
44 NORMAL DISPLAY CHECK
45 COLOR TEMP CHECK
46 COLOR SYSTEM CHECK
47 SOUND SYSTEM CHECK
48 MP-IN CHECK
49 NOISE MUTE CHECK
50 OSD LANGUAGE QUANTITY CHECK
51 MTS CHECKING
52 CLOSED CAPTION CHECKING
53 SHOCK TEST CHECK
21V-FS700S
ADJUSTMENT ITEM
EFFECTIVE MODEL

21V-FS700S
3 – 3
USER DATA IN SERVICE MODE
. While SERVICE mode ON, EEPROM DATA will switch to the service data.
Also, once SERVICE mode OFF, EEPROM will also switch to service (default) data .
. In the service mode, the user data establish as below,
USER DATA MODELS
PICTURE MAX 60
COLOUR CENTER 0
BRIGHT CENTER 0
TINT CENTER 0
SHARP CENTER 0
COLOR TEMP CENTER
S-VOLUME MIN
EQUALIZER *1
SURROUND OFF
BALANCE 0
AVL ON
BASS+ ON
OFF TIMER --:--
PASSWORD 0
BLUE BACK OFF
MP IN OFF
MTS STEREO
AIR / CABLE AIR
CH SEARCH AUTO
EZ SETUP AUTO
*1: Same as Movie mode default data
The flow of Mode list as following,
* Direct Key-in Mode for Service Items in Service Mode
RC CODE (HEX)
SERVICE-ITEM
C8 TV / VIDEO
28 DATA UP
A8 DATA DOWN
68 POWER / STANDBY
E8 S-MUTE
04 CHANGE MODE
64 V-LIN
54 V-SHI-50 / V-SHI-60
D4 V-SLOPE
74 H-SHI-50 / H-SHI-60
0C H-PAR
BC EW-W-50 / EW-W-60
E2 CUT-RS / CUT RS-DVD
0A DRI-GS / DRI-GS-DVD
6A CUT-RW / CUT-RW-DVD
9A DRI-GC / DRI-GC-DVD
3A DRI-GW / DRI-GW-DVD
9E VSD
31 SUB-TINT
B1 SUB-COLOR
71 SUB-BRI / SUB-BRI-DVD
F1 BLOC
C9 V-AMP-60 / V-AMP-50
83 AUTO RF-AGC
1F CUT-RC / CUT-RC-DVD
21V-FS700S

21V-FS700S
3 – 4
**AFTER INITIALIZED THE EEPROM (REFER TO FACTORY PRESETTING), READ DATA FROM
EEPROM ADDRESS 00H ~ 03H,AND COMPARE TO THE LIST BELOW, IF DIFFERENT,
INITIALIZE THE EEPROM.
ADDRESS DATA ADDRESS DATA
00H: 00H 02H: 03H
01H: 00H 03H: 1FH
*** There are two stages of service mode. First stage is ADJUSTMENT MODE; data from 01~36.
To go into second stage of service mode , press MENU key.Second stage is NVM MODE data from 000~3FF
ADJUSTMENT MODE (01~35)
1) Press CH UP/CH DOWN to select the item.
1) Press VOL UP/VOL DOWN to modify/ adjust the data.
01 RF-AGC
0…63 UOC-TV 23 AUTO AUTO
02 V-SLOPE
0…63 UOC-TV 28 ADJ ADJ
03 V-SHI-50
0…63 UOC-TV 33 ADJ ADJ
04 V-AMP-50
0…63 UOC-TV 28 ADJ ADJ
05 H-SHI-50
0…63 UOC-TV 38 ADJ ADJ
06 EW-W-50
0…63 UOC-TV 48 ADJ ADJ
07 E/W-PAR-50
0…63 UOC-TV 42 ADJ ADJ
08 H-PAR
0…63 UOC-TV 30 ADJ ADJ
09 H-BOW
0…63 UOC-TV 30 ADJ ADJ
10 UPCOR-PAR
0…63 UOC-TV 42 ADJ ADJ
11 LOCOR-PAR
0…63 UOC-TV 44 ADJ ADJ
12 E/W TRAP
0…63 UOC-TV 30 ADJ ADJ
13 V-LIN
0…63 UOC-TV 32 FIX 32
14 S-COR
0…63 UOC-TV 32 FIX 32
15 DRI-RS
0…63 UOC-TV 32 ADJ ADJ
16 DRI-GS
0…63 UOC-TV 32 FIX 32
17 DRI-BS
0…63 UOC-TV 32 ADJ ADJ
18 CUT-RS
0…63 UOC-TV 16 ADJ ADJ
19 CUT-GS
0…63 UOC-TV 16 ADJ ADJ
20 CUT-BS
0…63 UOC-TV 16 ADJ ADJ
21 SUB-BRI
0…63 UOC-TV 24 ADJ ADJ
22 SUB-CON
0…63 UOC-TV 59 ADJ ADJ
23 SUB-COL
0…63 UOC-TV 10 ADJ ADJ
24
SUB-TINT 0…63 UOC-TV 36 ADJ ADJ
25
SUB-SHARP 0…63 UOC-TV 10 FIX 10
26
V-SHI-60 0…63 UOC-TV 33 ADJ ADJ
27 V-AMP-60
0…63 UOC-TV 28 ADJ ADJ
28 H-SHI-60
0…63 UOC-TV 45 ADJ ADJ
29 EW-W-60
0…63 UOC-TV 48 ADJ ADJ
30
E/W-PAR-60 0…63 UOC-TV 42 ADJ ADJ
31 VSD
0/1 UOC-TV 1 FIX 1
32 CUT OFF
0…63 UOC-TV 25 FIX 25
33 DCXO
0…3 UOC-TV 50 FIX 50
34 ISP MODE
0/1 UOC-TV 0 FIX 0
35 BLOC
0…15 UOC-TV 4 FIX 4
FINAL DATA
PLS REFER
TO ADJ
ITEM FOR
WHITE
BALANCE
PLS REFER
TO ADJ
ITEM FOR
HORIZONT
AL,
VERTICAL,
DEFLECTIO
N LOOP
Default (DEC)
FIX/ADJ/AUT
O
Item
Setting Item
Setting Range
IC
REMARK

21V-FS700S
3 – 5
NVM MODE ITEMS (1/5)
1) Press CH UP / CH DOWN key to move the highlighted cursor (between NVM address and NVM data)
2) To change NVM address / modify data: VOL UP key= increase 0ne step data ; VOL DOWN key= decrease one step data ;
0~9key=0~9;FAVkeyA;FAVkeyB;FAVkeyC;FAVkeyD;MPXkey=E
DATA
MICON DEFAULT
EEPROM RANGE
REMARKS FINAL
D7 D6 D5 D4 D3 D2 D1 D0 [hex] [hex] DATA
0
0
0
0
0
0
0
1
0
0
0
2
03 00-FF FIX 03
0
0
0
3
1F 00-FF FIX 1F
0
0
0
8
17 00-3F ADJ ADJ
0
0
0
9
1C 00-3F ADJ ADJ
0
0
0
A
21 00-3F ADJ ADJ
0
0
0
B
1C 00-3F ADJ ADJ
0
0
0
C
26 00-3F ADJ ADJ
0
0
0
D
30 00-3F ADJ ADJ
0
0
0
E
2A 00-3F ADJ ADJ
0
0
0
F
1E 00-3F ADJ ADJ
0
0
1
0
1E 00-3F ADJ ADJ
0
0
1
1
2A 00-3F ADJ ADJ
0
0
1
2
2C 00-3F ADJ ADJ
0
0
1
3
1E 00-3F ADJ ADJ
0
0
1
4
20 00-3F FIX 20
0
0
1
5
20 00-3F FIX 20
0
0
1
6
20 00-3F ADJ ADJ
0
0
1
7
20 00-3F FIX 20
0
0
1
8
20 00-3F ADJ ADJ
0
0
1
9
10 00-3F ADJ ADJ
0
0
1
A
10 00-3F ADJ ADJ
0
0
1
B
18 00-3F ADJ ADJ
0
0
1
C
3B 00-3F ADJ ADJ
0
0
1
D
0A 00-3F ADJ ADJ
0
0
1
E
24 00-3F ADJ ADJ
0
0
1
F
0A 00-3F FIX 0A
0
0
2
0
21 00-3F FIX 21
0
0
2
1
20 00-3F FIX 20
0
0
2
2
21 00-3F FIX 21
0
0
2
3
21 00-3F FIX 21
0
0
2
4
29 00-3F FIX 29
0
0
2
5
1C 00-3F FIX 1C
0
0
2
6
1F 00-3F FIX 1F
0
0
2
7
27 00-3F FIX 27
0
0
2
8
1F 00-3F FIX 1F
0
0
2
9
20 00-3F FIX 20
0
0
2
A
28 00-3F FIX 28
0
0
2
B
20 00-3F FIX 20
0
0
2
C
20 00-3F FIX 20
0
0
2
D
22 00-3F FIX 22
0
0
2
E
20 00-3F FIX 20
0
0
2
F
1D 00-3F FIX 1D
0
0
3
0
20 00-3F FIX 20
0
0
3
1
20 00-3F FIX 20
0
0
3
2
1F 00-3F FIX 1F
0
0
3
3
20 00-3F FIX 20
0
0
3
4
28 00-3F FIX 28
0
0
3
5
20 00-3F FIX 20
0
0
3
6
20 00-3F FIX 20
0
0
3
7
22 00-3F FIX 22
0
0
3
8
20 00-3F FIX 20
0
0
3
9
1D 00-3F FIX 1D
0
0
3
A
20 00-3F FIX 20
0
0
3
B
20 00-3F FIX 20
0
0
3
C
27 00-3F FIX 27
0
0
3
D
23 00-3F FIX 23
0
0
3
E
1F 00-3F FIX 1F
0
0
3
F
0B 00-3F FIX 0B
Note: Highlighted items cannot be adjusted due fixed by software.( if adjusted it will has no effect)
0
RF-AGC (01)
VER-AMP-P50
H0R-SHI-P50
EW-W-P50
DRI-BW-DVD
CUT-GW-DVD
VER-SHI-P50
CUT-RW-DVD
CUT-RC-DVD
CUT-GC-DVD
DRI-RW-DVD
DRI-GW-DVD
CUT-GW
DRI-RC-DVD
DRI-GC-DVD
DRI-BC-DVD
DRI-RW
DRI-GW
DRI-BW
CUT-RW
DRI-GC
DRI-BC
CUT-RC
CUT-GC
SUB-BRI-DVD
SUB-CON-DVD
SUB-TINT-DVD
DRI-RC
DRI-GS-DVD
DRI-BS-DVD
CUT-RS-DVD
CUT-GS-DVD
SUB-COL (23)
SUB-TINT (24)
SUB-SHARP (25)
DRI-RS-DVD
CUT-RS (18)
CUT-GS (19)
SUB-BRI (21)
SUB-CON (22)
S-COR (14)
DRI-RS (15)
DRI-GS (16)
DRI-BS (17)
UPCOR-PAR (10)
LOCOR-PAR (11)
E/W-TRAP (12)
V-LIN (13)
EW-W-50 (06)
E/W-PAR-50 (07)
H-PAR (08)
H-BOW (09)
V-SLOPE (02)
V-SHI-50 (03)
V-AMP-50 (04)
H-SHI-50 (05)
0000-270F
FIX
PACKAGE NUMBER (MSB)
PACKAGE NUMBER (LSB)
ADDRESS
(HEX)
LOCKING PASSWORD
0000

21V-FS700S
3 – 6
NVM MODE ITEMS (2/5)
DATA
MICON DEFAULT
EEPROM RANGE
SETTING DATA FINAL
D7 D6 D5 D4 D3 D2 D1 D0 [hex] [hex] [hex] DATA
0
0
4
0
20 00-3F FIX 20
0
0
4
1
1F 00-3F ADJ ADJ
0
0
4
2
1F 00-3F ADJ ADJ
0
0
4
3
26 00-3F ADJ ADJ
0
0
4
4
20 00-3F ADJ ADJ
0
0
4
5
1F 00-3F ADJ ADJ
0
0
4
6
24 00-3F FIX 24
0
0
4
7
25 00-3F FIX 25
0
0
4
8
25 00-3F FIX 25
0
0
4
9
0A 00-3F FIX 0A
0
0
4
A1E 00-3F FIX 1E
0
0
4
B19 00-3F FIX 19
0
0
4
C32 00-04 FIX 32
0
0
4
D20 00-3F FIX 20
0
0
4
E20 00-3F FIX 20
0
0
4
F
20 00-3F FIX 20
0
0
5
0
20 00-3F FIX 20
0
0
5
1
20 00-3F FIX 20
0
0
5
2
20 00-3F FIX 20
0
0
5
3
20 00-3F FIX 20
0
0
5
4
20 00-3F FIX 20
0
0
5
5
20 00-3F FIX 20
0
0
5
6
20 00-3F FIX 20
0
0
5
7
1F 00-3F FIX 1F
0
0
5
8
20 00-3F FIX 20
0
0
5
9
24 00-3F FIX 24
0
0
5
A20 00-3F FIX 20
0
0
5
B20 00-3F FIX 20
0
0
5
C21 00-3F FIX 21
0
0
5
D20 00-3F FIX 20
0
0
5
E1F 00-3F FIX 1F
0
0
5
F
20 00-3F FIX 20
0
0
6
0
20 00-3F FIX 20
0
0
6
1
1E 00-3E FIX 1E
0
0
6
2
1E 00-3E FIX 1E
0
0
6
3
1E 00-3E FIX 1E
0
0
6
4
28 00-3E FIX 28
0
0
6
5
24 00-3E FIX 24
0
0
6
6
27 00-3E FIX 27
0
0
6
7
27 00-3E FIX 27
0
0
6
8
21 00-3E FIX 21
0
0
6
9
1D 00-3E FIX 1D
0
0
6
A2B 00-3E FIX 2B
0
0
6
B23 00-3E FIX 23
0
0
6
C1F 00-3E FIX 1F
0
0
6
D1F 00-3E FIX 1F
0
0
6
E28 00-3E BUS SETUP 24
0
0
6
F
27 00-3E 2C
0
0
7
0
2F 00-3E FIX 2F
0
0
7
1
1F 00-3E FIX 1F
0
0
7
2
1F 00-3E FIX 1F
0
0
7
3
20 00-3F FIX 20
0
0
7
4
0D 00-3C FIX 0D
0
0
7
5
0D 00-3C FIX 0D
0
0
7
6
0D 00-3C FIX 0D
0
0
7
7
12 00-3C FIX 12
0
0
7
8
12 00-3C FIX 12
0
0
7
9
12 00-3C FIX 12
0
0
7
A1E 00-3E FIX 1E
0
0
7
B1E 00-3E FIX 1E
0
0
7
C1E 00-3E FIX 1E
0
0
7
D1E 00-3E FIX 1E
0
0
7
E18 00-3E FIX 18
0
0
7
F
24 00-3E FIX 24
Note: Highlighted items cannot be adjusted due fixed by software.( if adjusted it will has no effect)
U-COL-NEWS
U-COL-MUSC
U-BRI-MOV
U-COL-MOV
U-TREBLE_NEWS
U-TREBLE_MOV
U-BRI-MUSC
U-BRI-NEWS
DRI-GLW-DVD (58)
EW-W-60 (29)
E/W-PAR-60 (30)
VER-SHI-P60
VER-AMP-P60
H0R-SHI-P60
EW-W-P60
E/W-PAR-P60
CUT OFF (32)
ADDRESS
(HEX)
H-SHI-60 (28)
V-AMP-60 (27)
V-SHI-60 (26)
E/W-PAR-P50
DCXO (33)
DRI-RLC (40)
DRI-GLC (41)
DRI-BLC (42)
CUT-RLC (43)
CUT-GLC (44)
DRI-RLW (30)
DRI-GLW (31)
DRI-BLW (32)
CUT-RLW (33)
CUT-GLW (34)
DRI-RLC-DVD (67)
DRI-GLC-DVD (68)
DRI-BLC-DVD (69)
CUT-RLC-DVD (70)
CUT-GLC-DVD (71)
DRI-RLW-DVD (57)
DRI-BLW-DVD (59)
CUT-RLW-DVD (60)
CUT-GLW-DVD (61)
OF-COL-TV
OF-COL-AV
OF-COL-DVD
OF-COL-P
OF-COL-S
OF-COL-N4
OF-SHP-P
OF-SHP-S
OF-COL-N3
OF-SHP-TV
OF-SHP-AV
OF-SHP-DVD
OF-SHP-N4
OF-SHP-N3
OF-TINT-TV
OF-TINT-AV
OFFSET_OF_COL_DVD_FIELD_FREQ_60HZ
OF-TINT-ADJ
BB-TINT
U-BASS_MUSC
U-BASS_NEWS
U-BASS_MOV
U-TREBLE_MUSC
BUS SETUP

21V-FS700S
3 – 7
NVM MODE ITEMS (3/5)
DATA
MICON DEFAULT
EEPROM RANGE
SETTING DATA FINAL
D7 D6 D5 D4 D3 D2 D1 D0 [hex] [hex] [hex] DATA
0
0
8
0
3C 00-3C FIX 3C
0
0
8
1
32 00-3C FIX 32
0
0
8
2
3C 00-3C FIX 3C
0
0
8
3
1E 00-3E FIX 1E
0
0
8
4
18 00-3E FIX 18
0
0
8
5
24 00-3E FIX 24
0
0
8
6
16 00-1F FIX 16
0
0
8
7
30 00-3F FIX 30
0
0
8
8
04 00-3F FIX 04
0
0
8
9
0F 00-20 FIX 0F
0
0
8
A05 00-07 FIX 05
0
0
8
B19 00-3F FIX 19
0
0
8
C1F 00-3E FIX 1F
0
0
8
D46 00-FF FIX 46
0
0
8
E71 00-FF FIX 71
0
0
8
F
76 00-FF FIX 76
0
0
9
0
7B 00-FF FIX 7B
0
0
9
1
82 00-FF FIX 82
0
0
9
2
8A 00-FF FIX 8A
0
0
9
3
91 00-FF FIX 91
0
0
9
4
15 00-3C FIX 15
0
0
9
5
3C 00-3C FIX 3C
0
0
9
6
07 00-3C FIX 07
0
0
9
7
0
0
9
8
0
0
9
9
05 00-3C FIX 05
0
0
9
A02 01-7D FIX 02
0
0
9
B3A 00-3C FIX 3A
0
0
9
C11 00-18 FIX 11
0
0
9
D11 00-18 FIX 11
0
0
9
E06 00-18 FIX 06
0
0
9
F
0C 00-18 FIX 0C
0
0
A
0
14 00-18 FIX 14
0
0
A
1
08 00-18 FIX 08
0
0
A
2
0E 00-18 FIX 0E
0
0
A
3
11 00-18 FIX 11
0
0
A
4
0E 00-18 FIX 0E
0
0
A
5
0B 00-18 FIX 0B
0
0
A
6
10 00-18 FIX 10
0
0
A
7
10 00-18 FIX 10
0
0
A
8
12 00-18 FIX 12
0
0
A
9
0F 00-18 FIX 0F
0
0
A
A15 00-18 FIX 15
0
0
A
B64 00-FF FIX 64
0
0
A
CC8 00-FF FIX C8
0
0
A
D0B 00-1F FIX 0B
0
0
A
E0B 00-1F FIX 0B
0
0
A
F
0F 00-1F FIX 0F
0
0
B
0
0A 00-1F FIX 0A
0
0
B
1
12 00-1F FIX 12
0
0
B
2
10 00-1F FIX 10
0
0
B
3
00 00-3F FIX 00
0
0
B
4
00 00-FF FIX 00
0
0
B
5
00 00-3F FIX 00
0
0
B
6
00 00-FF FIX 00
0
0
B
7
00 00-1F FIX 00
0
0
B
8
00 00-1F FIX 00
0
0
B
9
0C 00-3C FIX 0C
0
0
B
A01 00-1E FIX 01
0
0
B
B01 00-1E FIX 01
0
0
B
C01 00-1E FIX 01
0
0
B
D01 00-1E FIX 01
0
0
B
E01 00-1E FIX 01
0
0
B
F
01 00-1E FIX 01
Note: Highlighted items cannot be adjusted due fixed by software.( if adjusted it will has no effect)
PRESET_EQA_3K_MUSC
PRESET_LOUDNESS_OFF_BASS_DOWN_MUSC
PRESET_LOUDNESS_OFF_BASS_DOWN_NEWS
TREB-CT
FSRT_AVOUT_LEVEL
PRESET_EQA_8K_MOV
NLOERLIM
NUPERLIM
PRESET_EQA_8K_NEWS
PRESET_EQA_100_MOV
PRESET_EQA_300_MOV
BASS-CT
DECLEV
MONOLEV
NICLEV
SAPLEV
ADCLEV
IISLEV
PRESET_EQA_8K_MUSC
PRESET_EQA_100_NEWS
PRESET_EQA_300_NEWS
PRESET_EQA_3K_NEWS
PRESET_EQA_1K_NEWS
OPTION_HOTEL_MAX_VOL
PRESET_EQA_1K_MUSC
OPTION HOTEL PRG
SUB-VOL (64)
PRESET_EQA_100_MUSC
PRESET_EQA_300_MUSC
FDAC_S_STEP
FDAC_SMER6_VOL
FDAC_S_ST_POINT
FDAC_S_SP_POINT
FDAC_SMER5_VOL
FDAC_SMER1_VOL
FDAC_SMER2_VOL
FDAC_SMER3_VOL
FDAC_SMER4_VOL
SVM2-0-NTSC
VER-AMP-START
OFFSET_OF_COL_DVD_FIELD_FREQ_50HZ
FDAC_SMEL
OSD-BRIGHTNESS
V-POS-OSD (50HZ)
H-POS-OSD
AUTO-AGC-MAX
U-CON-MOV
U-SHP-MUSC
U-SHP-NEWS
U-SHP-MOV
ADDRESS
(HEX)
U-CON-MUSC
U-CON-NEWS
PRESET_LOUDNESS_OFF_TREBLE_DOWN_MOV
DUBADR
DUBCOEF
PRESET_LOUDNESS_OFF_BASS_DOWN_MOV
PRESET_LOUDNESS_OFF_TREBLE_DOWN_MUSC
PRESET_LOUDNESS_OFF_TREBLE_DOWN_NEWS
PRESET_EQA_1K_MOV
PRESET_EQA_3K_MOV
DBECOEF
DBEADR

21V-FS700S
3 – 8
SLAVE ADDRESS : A0(00-FF) A2(100-1FF) A4(200-2FF) A6(300-3FF) A8(400-4FF) AA(500-5FF) AC(600-6FF) AE(700-7FF)
DATA
MICON DEFAULT
EEPROM RANGE
FINAL
D7 D6 D5 D4 D3 D2 D1 D0 [hex] [hex] DATA
0
0
C
0
26 00-3F FIX 26
0
0
C
1
0B 00-3F FIX 0B
0
0
C
2
18 00-3F FIX 18
0
0
C
3
10 00-3F ADJ ADJ
0
0
C
4
20 00-3F FIX 20
0
0
C
5
0D 00-1F FIX 0D
0
0
C
6
CF 00-FF FIX CF
0
0
C
7
A9 00-FF FIX A9
0
0
C
8
00 00-FF FIX 00
0
0
C
9
B0 00-FF FIX B0
0
0
C
A0F 00-FF FIX 0F
0
0
C
B1E 00-FF FIX 1E
0
0
C
C2D 00-FF FIX 2D
0
0
C
D
TUNER
BAND
TUNER
System
22 00-A2 FIX 22
0
0
C
E20 00-FF FIX 20
0
0
C
F
20 00-3C FIX 20
0
0
D
0
1F 00-3C FIX 1F
0
0
D
1
1F 00-3C FIX 1F
0
0
D
2
20 00-3C FIX 20
0
0
D
3
1F 00-3E FIX 1F
0
0
D
4
1C 00-3F FIX 1C
0
0
D
5
00 00-3F FIX 00
0
0
D
6
00 00-3F FIX 00
0
0
D
7
0
0
D
8
0
0
D
9
0
0
D
A
0
0
D
B
0
0
D
C
OFFSET_OF_TINT_DVD_FIELD_FREQ_50HZ
OFFSET_OF_TINT_DVD_FIELD_FREQ_60HZ
TELETEXT-OSD-BRIGHTNESS
H-POS-TEXT
V-POS-OSD (60HZ)
CUT-BS (20)
CUT-BS-DVD
ADDRESS
(HEX)
V-POS-TEXT-50HZ
REMARKS
STARTMER2
STARTMER1
SMEL-GAIN
OFF_CON
FDAC-VOL2
STOPMER
FDAC-VOL1
OFFSET_OF_TINT_DVD
FDAC-VOL3
TUNER_SELECT
ION
FTUN_OFFSDEM_IF
OFF_BRI
OFFSET_SHARPNESS_LNA
AV2_BRI
OFFSET_TINT_N443

21V-FS700S
3 – 9
SLAVE ADDRESS : A0(00-FF) A2(100-1FF) A4(200-2FF) A6(300-3FF) A8(400-4FF) AA(500-5FF) AC(600-6FF) AE(700-7FF)
DATA
MICON DEFAULT
EEPROM RANGE
FINAL
D7 D6 D5 D4 D3 D2 D1 D0
[hex] [hex] DATA
0
1
0
A
0
1
0
B
0
1
0
C
0
1
0
D
0
1
0
E
0
1
0
F
0
1
1
0
0
1
1
1
0
1
1
2
0
1
1
3
0
1
1
4
0
1
1
5
0
1
1
6
0
1
1
7
0
1
1
8
0
1
1
9
0
1
1
A
0
1
1
B
0
1
1
C
0
1
1
D
0
1
1
E21 00-FF FIX 21
0
1
1
F
11 00-FF FIX 11
0
1
2
0
40 00-FF FIX 40
0
1
2
1
00 00-FF FIX 00
0
1
2
2
67 00-FF FIX 67
0
1
2
3
35 00-37 FIX 35
0
1
2
4
E6 00-FF FIX E6
0
1
2
5
84 00-FF
BUS SETUP
D6
0
1
2
6
41 00-F0 FIX 41
0
1
2
7
34 00-5F FIX 34
0
1
2
8
15
00-07 FIX 15
0
1
2
9
55
00-F5 FIX 55
0
1
2
A33
00-54 FIX 33
0
1
2
B40
00-0F FIX 40
0
1
2
C4D
00-FF FIX 4D
0
1
2
D4D
00-4F FIX 4D
0
1
2
E45
00-FF FIX 45
0
1
2
F
13
00-FF FIX 13
0
1
3
0
01
00-01 FIX 01
LANGUAGE_
OPTION:
0=Only
English
available
1=English&
Spanish
available
0
1
3
1
0
1
3
2
16 00-26 FIX 16
COLOR
TEMP:
0=Warm
1 = Middle
2=Cool
0
1
3
3
10 00-21 FIX 10
LANGUAGE:
0 = English
1 = Spanish
0
1
3
4
01 00-02 FIX 01
0
1
3
5
0
1
3
6
0
1
3
7
0
1
3
8
0
1
3
9
0
1
3
A
0
1
3
B
0
1
3
C
0
1
3
D
0
1
3
E
0
1
3
F
04 00-FC FIX 04
PEAKFREQPALN
PEAKFREQPALM
PEAKFREQPAL443
COR1-0
COLOR TEMP (MOVIE)
LANGUAGE
COLOR TEMP (NEWS)
COLOR TEMP (MUSIC)
FZOM_ZOOM_MODE
FSND_LOUDNESS_VOL_DB4
FSND_LOUDNESS_VOL_DB3
LANGUAGE_OPTION
LANGUAGE_OPTION
TELETEXT_60HZ_WBR
FSND_LOUDNESS_VOL_DB2
FSND_LOUDNESS_VOL_DB1
TELETEXT_50HZ_WBF
FSND_ITEM_BAMAFC
TELETEXT_60HZ_WBF
TELETEXT_50HZ_WBR
AVLLE
FSND_ITEM_AVLMODE
FSND_ITEM_VDS
FSND_ITEM_CLIPMANAG
INSOEF
PWLDAC
TELETEXT-BLOC
FSND_ITEM_MAINLONA
WBR-60-F-C-P
WBF-60-F-C-P
BLOC (35)
LOUDNESS_LDS0-2
PW-TIME
SVM2-0-PAL
WBR-50-F-C-P
WBF-50-F-C-P
YD AV-N443
YD AV-N358
CL3-0
YD COMP
YD N443
YD N358
YD AV-SECAM
YD AV-PAL
YD SECAM
YD PAL
ADDRESS
(HEX)
REMARKS

21V-FS700S
3 – 10
SLAVE ADDRESS : A0(00-FF) A2(100-1FF) A4(200-2FF) A6(300-3FF) A8(400-4FF) AA(500-5FF) AC(600-6FF) AE(700-7FF)
DATA
MICON DEFAULT
EEPROM RANGE
FINAL
D7 D6 D5 D4 D3 D2 D1 D0
[hex] [hex] DATA
0
1
4
0
D1 00-FF FIX D1
0
1
4
1
6D 00AF FIX 6D
0
1
4
2
77 00-FF FIX 77
0
1
4
3
77 00-FF FIX 77
0
1
4
4
02 00-00 FIX 02
0
1
4
5
92 00-BC FIX 92
0
1
4
6
00 00-FF FIX 00
0
1
4
7
01
00-B3 FIX 01
0
1
4
8
03
00-03 FIX 03
OPTION_BASS+:
0 = Without BASS+ function
1 = With BASS+ function
2(This value is not valid)
= With BASS+ and SHAKIT
functions(Controlled by user
item "BASS+")
3 = With LOUDNESS function
(Controlled by user item
"Bass+")
0
1
4
9
0
1
4
A
0
1
4
B
0
1
4
C
0
1
4
D
0
1
4
E
0
1
4
F
0
1
5
0
0
1
5
1
04 00-02 FIX 04
0
1
5
2
56 00-58 FIX 56
0
1
5
3
00
00-00 FIX 00
0
1
5
4
0
1
5
5
0
1
5
6
0
1
5
7
0
1
5
8
0
1
5
9
0
1
5
A
0
1
5
B
0
1
5
C
0
1
5
D
PWL VSD (31) VIRGIN BPB2 FMI MUS PHI FORCE
DSK-NOT-
PAL-AV
D2 00-C7 FIX D2
0
1
5
E
DSK-NOT-
PAL-DVD
DSK-PAL-
DVD
DSK-PAL-
AV
BKS GAM BSD INCL-AV
1B 00-FF FIX 1B
0
1
5
F
ISP MODE
(34)
AEVS_ITE
M_POR
ERR-
VERTG
ERR-
SUPVOL
ERR-XRAY
ERR-1-8-
SUP
4C 00-3F FIX 4C
0
1
6
0
ID-PGAIN ID-BYBPF TFR
OPTION_H
OTEL
LOUDNESS
_HIGH_BO
OST
DTR AGN DSG
0F 00-FF FIX 0F
0
1
6
1
BAMASUB AVLWGT MAINLOCH
MULTI21_S
YSTEM_OP
TION
NICDEEM NDETPB FMSUB-BW MPX-P-BW
E0
00-FF FIX E0
0
1
6
2
BILLINGUA
L_OPTION
YUV_OPTI
ON
FRONTAV_
OPTION
NRR CP-TUNER TXT-ON TXT-WEST TXT-EURO
68
00-F8 FIX 68
0
1
6
3
OPTION_M
PIN
OPTION_S
URROUND
OPTION_D
VD
OPTION_A
V2
EW_OPTIO
N
EQ_OPTIO
N
OPTION_L
NA_BOOST
ER
OPTION_S
HAKIT
F4
00-FF FIX F4
0
1
6
4
OPTION_BI
LINGUAL
OPTION_S
YSTEM(AV)
TREBLE
offset
EFFECT
BASS offset
EFFECT
ICS
(CLOSE
QSS)
OPTION_A
VL_OSD
CB CBS
86 00-C7 FIX 86
0
1
6
5
OPTION_V
OL
DSGLS_AV DSGLS_TV
OPTION_L
OUDNESS
ITEM_OVM
ADAPT
FIMG_ITEM
_BLS
OPTION_E
Q_OFFSET
OPTION
SPEAKER
80
00-9F FIX 80
0
1
6
6
A
㪭㪣㪶㪦㪥㪦㪝
㪝㪶㪦㪧㪫㪠㪦㪥
F
㪪㪩㪫㪶㪠㪫㪜㪤
㪶㪞㪛
F
㪪㪥㪛㪶㪛㪪㪞
㪣㪪
07
00-07 FIX 07
0
1
6
7
0
1
6
8
AUTO
SELECT
M.P. IN BLUE BACK
LAST
POWER
LOCK TV AVL
SAVE
MODE
PICTURE
NR
(MUSIC)
F4 00-7F FIX F4
BLUE BACK:
0=On
1=Off
0
1
6
9
DAC_MOD
E_NTSC
DATA
(CLOSED
CAPTION)
PICTURE
NR (NEWS)
PICTURE
NR
(MOVIE)
BASS+
S-
BOOSTER
NICAM_A2_
MODE
MAINLOUD
0D 00-71 FIX 0D
0
1
6
A
S-
BOOSTER
(NEWS)
S-
BOOSTER
(MUSIC)
S-
BOOSTER
(MOVIE)
SPEAKER
VIRGIN_BIT
(NTSC)
13
00-01 FIX 13
0
3
F
F
--
--
BUS SETUP
00
LANGUAGE:
00 = English
01 = Spanish
REMARKS
MODE
(CLOSED CAPTION)
AIR/CABLE
SURROUND (MOVIE)
BASSFEATURE_CTL
IDMOD-SE
BAMAMO
OVMTHR
OPTION_BASS+
SURROUND (NEWS)
SURROUND (MUSIC)
DIGIT ENTRY MODE
FILTBW
EIAJ-DEL
FILTBW-M
RPO
RPA
SOC
AAS0_1
PRESET_SURROUND_
MOV
PRESET_SURROUND_
NEWS
PRESET_SURROUND_
MUSC
TREBLE_FREQ_SELEC
TION
BASS_FREQ_SELECTI
ON
PRESET_COR_MUSC
PRESET_WS_CTM
PRESET_COR_CTM
PRESET_WS_MOV
PRESET_COR_MOV
ADDRESS
(HEX)
PEAKFREQDVD
PEAKFREQSECAM
FACTORY SHIPOUT LANGUAGE (STEREO NTSC)
PEAKFREQNTSCM
PEAKFREQNTSC443
PW-LAST
AUDIO-CFG
PHI
H-POS-FINE
PRESET_WS_NEWS
PRESET_COR_NEWS
PRESET_WS_MUSC
LCKEY-
SRV-ENTER
Note 1
Note 2
REMARKS
*Note 1 : Item DAC_Mode ON
: In production , when the operator plug in main power switch and press the ON/OFF Switch, the set will automatically ON. Therefore, operator need not have to press
the Power On button of Remote Control key.
*Note 2 : Item Virgin_Bit OFF
: If Virgin_Bit is ON, the language selection will appear at TV screen. If OFF, language selection will not appear. Therefore, operator will not have to choose the language
and able to reduce a single step.

21V-FS700S
3 – 11
Data
(HEX)
06F OF-TINT-TV 24 FIX
070 OF-TINT-AV 2C FIX
125
WBR-60-F-C-P / WBF-60-F-C-P D6 FIX
3FF
FACTORY SHIPOUT LANGUAGE
(STEREO NTSC)
00
FIX
LANGUAGE:
00 = English
01 = Spanish
BUS SET UP (EEPROM DATA)
REMARK
EEPROM ITEMS
Address
(HEX)

21V-FS700S
3 – 12
SHIPPING SETTING & CHECKING
(1) The following default data has been factory-set for the E2PROM follow by pressing MODEL SET key.
LANGUAGE MODEL-SET KEY
ENGLISH 3
ITEMS DATA SETTING
LAST POWER ON
LAST TV/AV MODE TV MODE
LAST POSITION CH 1
FLASHBACK CHANNEL CH 1
VOLUME 0 (Min)
MOVIE
OFF TIMER --:--
CHILD LOCK OFF
PASSWORD 0000
BLUE BACK OFF
M.P.In ON
SKIP ALL CH OFF
FAVORITE PROGRAM A CH 10
FAVORITE PROGRAM B CH 20
FAVORITE PROGRAM C CH 30
FAVORITE PROGRAM D CH 40
AIR/CABLE AIR
PICTURE 60
COLOUR +6
BRIGHT 0
TINT 0
SHARP +6
PICTURE NR OFF
COLOR TEMP 0
SURROUND OFF
BALANCE 0
AVL ON
BASS+ ON
FACTORY SETTING BY MODEL
(Reference: Geomagnetism Adjustment)
MODEL MAGNETIC FIELD(V, H) nT BACKGROUND LANG. S-SYS LANG QTY
PHILIPPINES 10,000 39,000 ENGLISH M 2
1: ENGLISH / SPANISH
M
SOUND SYSTEM
AV MODE
15000°K

21V-FS700S
3 – 13
[2] ADJUSTMENT
ADJUSTMENT PRECAUTION: Makesure TV Set is in “Normal Condition” before switch to Service Mode for Adjustment.
1. PIF ADJUSTMENT CHECKING
2. FOCUS ADJUSTMENT
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR OTHERS
1RF-AGC TAKE OVER
POINT ADJUSTMENT
(I2C BUS CONTROL)
(AUTO & MANUAL ADJ)
* for Auto ADJ
(1) Receive "PAL COLOR BAR"
signal
53 ± 1 dBµV (75 ohm open).
(2) Go to service mode.
(3) Go to service data 01 RF-AGC,
press R/C to operate auto key
(Hex C1). Blue display with OK
sign indicates the adjustment is
working properly
(4) If appear red display with NG
sign, increase data some step
and please repeat step 2.
(5) Proceed step3&4inmanual
mode.
TV SET
OSCILLOSCOPE
BIAS BOX
+
-
TP201
0.1V
1.0V -
+
(1) Receive "PAL COLOR BAR" signal.
Signal Strength: 53 ± 1dBµV (75 ohm open)
(2) Connect the oscilloscope to JA402 (Tuner's
AGC Terminal) as shown in figure 3-1.
(3) Call "01 RF-AGC" mode in service mode.
Adjust the "01RF AGC" bus data to obtain
the Tuner output pin drop 0.1~1.0V below
maximum voltage.
(4) Change the antenna input signal to
63 ~ 67dBµV, and make sure there is
no noise.
(5) Turn up the input signal to 90 ~ 95 dBµV to
be sure that there is no cross modulation beat.
signal strength :
NO ADJUSTMENT POINT WAVEFORM OR OTHERS
1FOCUS (1) Receive the "Monoscope Pattern" signal.
(2) Press R/C to set Picture NORMAL condition.
(3) Adjust the focus control to get the best
focusing.
ADJUSTMENT CONDITION / PROCEDURE
Focusing
Point
(middle of
center and
edge of
monoscope
pattern)

21V-FS700S
3 – 14
3. HORIZONTAL, VERTICAL, DEFLECTION LOOP ADJUSTMENT
NO ADJUSTMENT POINT WAVEFORM OR OTHERS
1V-SLOPE
(I2C BUS CONTROL)
ADJUSTMENT CONDITION / PROCEDURE
(1) Receive US12 CH LION HEAD Signal
(NTSC 60 Hz).
(2) Choose the service data 02 V-SLOPE.
(3) Adjust the V-SLOPE as shown in Figure 1.1
CAUTION:- PLEASE AGING TV MORE THAN
10 MINUTES BEFORE ADJUSTMENT.
2V-SHIFT-60
(I2C BUS CONTROL)
(1) Receive US12 CH LION HEAD Signal
(NTSC 60 Hz).
(2) Choose the service data 26 V-SHIFT-60
(3) Align the center of the screen to the geometric
center of CRT.
Note: B line (Monoscope middle line) must
same or nearest higher position to the A
mark (Tube middle mark), refer to the attach
drawing.
Figure 1.1
Figure:
3V-AMP-60
(12C BUS CONTROL)
(to be done after
V-shift adj)
(1) Receive US12 CH LION HEAD Signal
(NTSC 60 Hz).
(2) Choose the service data 27 V-AMP-60
(3) Adjust V-AMP-60 bus data until the overscan
become 10 ± 1.5 %.
Caution 1: Pls aging TV more than
10 minutes before adjustment
6H-SHI- 60
(I2C BUS CONTROL)
(1) Receive US12 CH LION HEAD Signal
(NTSC 60 Hz).
(2) Choose the service data 28 H-SHI-60.
(3) Adjust the H-SHI-60 bus data to have a
balance position to spec of A=B
(as attach drawing).
(4) If cannot make it to A=B, adjust from the
best point so that Bslightly smaller than A.
A = Out of spec
B=OK
C = Out of spec
A
B
C
A
OK OK NG
B
AB
NTSC Adjustment
(using RF signal)
4
5
V-LIN
(I2C BUS CONTROL)
(1) Receive US12 CH LION HEAD Signal
(NTSC 60 Hz).
(2) Choose the service data 13 V-LIN
(3) Already preset. (Adjust this unless the linearity
is achieved.)
S COR
(I2C BUS CONTROL)
(1) Receive US12 CH LION HEAD Signal
(NTSC 60 Hz).
(2) Choose the service data 14 S COR.
(3) Already preset. (Adjust this unless the linearity
is achieved.)

21V-FS700S
3 – 15
NO ADJUSTMENT POINT WAVEFORM OR OTHERS
7EW-W-60
(I2C BUS CONTROL)
ADJUSTMENT CONDITION / PROCEDURE
(1) Receive US12 CH LION HEAD Signal
(NTSC 60 Hz).
(2) Choose the service data 29 EW-W-60.
(3) Adjust EW-W-60 bus data until the overscan
becomes 10 ± 1.5 %.
8E/W-PAR-60
(I2C BUS CONTROL)
(1) Receive CrossHatch Pattern Signal
(NTSC 60 Hz)
(2) Choose the service data 30 E/W-W-60.
(3) Adjust the 2nd vertical line from the right
end of the crosshatch pattern so that the
middle 4 blocks are straight.
9UPCOR-PAR
(I2C BUS CONTROL)
(1) Receive CrossHatch Pattern Signal
(NTSC 60 Hz).
(2) Choose the service data 10 UPCOR-PAR.
(3) Adjust the 2nd upper vertical line from the
right end of the crosshatch pattern so that the
upper line are straight.
10 LOCOR-PAR
(I2C BUS CONTROL)
(1) Receive CrossHatch Pattern Signal
(NTSC 60 Hz).
(2) Choose the service data 11 LOCOR-PAR.
(3) Adjust the 2nd lower vertical line from the right
end of the crosshatch pattern so that the
bottom line are straight.
11 H-BOW
(I2C BUS CONTROL)
(1) Receive CrossHatch Pattern Signal
(NTSC 60 Hz).
(2) Choose the service data 9 H-BOW.
(3) Adjust the 2nd vertical line from the end of the
crosshatch pattern until line is straight
(4) Please refer Figure 9.1
12 H-PAR
(I2C BUS CONTROL)
(1) Receive CrossHatch Pattern Signal
(NTSC 60 Hz).
(2) Choose the service data 8 H-PAR.
(3) Adjust the 2nd vertical line from the end of the
crosshatch pattern line is straight
(4) Please refer Figure 10.1
13 EW-TRAP
(I2C BUS CONTROL)
(1) Receive CrossHatch Pattern Signal
(NTSC 60 HZ).
(2) Choose the service data 12 EW-TRAP.
(3) Adjust the 2nd vertical line from the right
end of the crosshatch pattern so that the
D1 (center area of the second vertical
line - edge of screen) and D2 (top area of
the second vertical line - edge of screen)
are same.
H-PAR
Figure 9.1
Figure 10.1
D2
D1
H-BOW

21V-FS700S
3 – 16
14 V-SHIFT50
(I2C BUS CONTROL)
(1) Receive Monoscope Pattern Signal
(PAL 50 Hz).
(2) Choose the service data 03 V-SHI-50
(3) Adjust V-SHI-50 bus data to have a most
acceptable vertical position, the monoscope
pattern should be Balance in vertical position.
Note: B line (Monoscope middle line) must
same or nearest higher position to the A
mark (Tube middle mark), refer to the attach
drawing.
Figure:
15 V-AMP-50
(12C BUS CONTROL)
(to be done after
V-shift adj)
(1) Receive Monoscope Pattern Signal
(PAL 50 Hz).
(2) Choose the service data 04 V-AMP-50.
(3) Adjust V-AMP-50 bus data until the overscan
become 10 ± 1.5 %.
Caution 1: Pls aging TV more than
10 minutes before adjustment
16 H-SHIFT-50
(I2C BUS CONTROL)
(1) Receive Monoscope Pattern Signal
(PAL 50 Hz).
(2) Choose the service data 05 H-SHI-50.
(3) Adjust the H-SHI-50 bus data to have a
balance position to spec of A=B
(as attach drawing).
(4) If cannot make it to A=B, adjust from the
best point so that Bslightly smaller than A.
A
OK OK NG
B
AB
NO ADJUSTMENT POINT WAVEFORM OR OTHERSADJUSTMENT CONDITION / PROCEDURE
17 EW-W-50
(I2C BUS CONTROL)
(1) Receive Monoscope Pattern Signal
(PAL 50 Hz).
(2) Choose the service data 06 EW-W-50.
(3) Adjust EW-W-50 bus data until the overscan
becomes 10 ± 1.5 %.
18 E/W-PAR-50
(I2C BUS CONTROL)
(1) Receive CrossHatch Pattern Signal
(PAL 50 Hz).
(2) Choose the service data 07 E/W-PAR-50.
(3) Adjust the 2nd vertical line from the right
end of the crosshatch pattern so that the
middle 4 blocks are straight.
PAL Adjustment
(using external signal
to input AV)

21V-FS700S
3 – 17
4. SCREEN, WHITE BALANCE, SUB-BRIGHTNESS & SUB-CONTRAST ADJUSTMENT
NO ADJUSTMENT POINT WAVEFORM OR OTHERS
1SCREEN
ADJUSTMENT
(I2C BUS CONTROL)
ADJUSTMENT CONDITION / PROCEDURE
(1) Make sure the following items are in INITIAL
DATA before adjust CRT cutoff
(a) 15 DRI-RS = 32
(b) 16 DRI-GS = 32
(c) 17 DRI-BS = 32
(d) 18 CUT-RS = 16
(e) 19 CUT-GS = 16
(f) 20 CUT-BS = 16
(f) 21 SUB BRI = 24
(g) 22 SUB CON = 59
(h) 32 CUT OFF = 25
(i) 35 BLOC = 4
(2) Switch TV to video mode, blue back off, with
no signal and press R/C to set picture into
normal condition.
(3) Go to service mode, select item 31 VSD
(dark screen display)
(4) Adjust the Screen so that cut-off line appear in
low bright, then judge that whether the cut-off
line appear in Red or Green or Blue color, in
this condition between CUT-RS & CUT-GS &
cut-BS, fix the data of the color appear in
cut-off line and adj the other two cut-off data
(Note 1) so that cut-off line color become white.
(5) Turn the screen VR of FBT so that cut-off line
just disappear
(1) WHITE (HIGH BEAM)
First use Minolta Color Analyzer CA100, let the
gun point at Dark White position (as drawing
attach), Adj SUB-BRI until LUMINANCE Y
become 1.5 cd/m2, then let the gun point at
White position (as drawing attach), Adj SUB-
CON until LUMINANCE Y become: 150 cd/m2.
Adj the DRI-RS & DRI-BS until the axis of color
temperature become
15000 K X : 0.254 , Y : 0.261
(2) DARK WHITE (LOW BEAM)
Let the gun point at Dark White position, if
the color temperature data shift away from the
data adjusted in Item 1 Screen adjustment,
adjust CUT-RS, CUT GS & CUT-BS.
Please fix the first colour appears in Screen
adj item step (4) is fixed, adj the other two
so that to obtain the similar axis as above.
**Repeatstep1&2togetaregulated
position
*Note:
During Service Mode select 31 VSD
(dark screen display), if the vertical line
does not appaer please press VOL UP
key.
*Note : Use RF window pattern US14
2WHITE BALANCE ADJ
(to be done after
screen adj)
(I2C BUS CONTROL) White
50% WHITE
Dark
White
°
(US-14 CH)