Sharper Image 203206 User manual
3-In-1 Smart Groomer
Item No. 203206
User’s Guide
Maintain a clean, neat appearance
Thank you for purchasing the Sharper lmage 3-in-1Smart Groomer. This product, along with the entire Sharper lmage
collection, combines innovation with cutting-edge design to provide you with years of dependability and enjoyment.
This 3-in-1 Smart Groomer is designed to help you trim and groom your facial hair (beard, moustache, sideburns),
nosr hair, ear hair and eyebrows to achieve a stylish and professional appearance at home or when you travel.
Please read and follow these instructions, and store them for future reference.
Using the Beard/Moustache Trimmer
Remove the Shaver Cap. Then, slide the power
switch to the “Shave/Trim” position. Slide the
Beard/Moustache Trimmer blade forward with
your thumb. Note: You can use the Beard/
Moustache Trimmer for small areas, such as
hairline, sideburns, etc. Hairs should be free
of lotion when using this trimmer.
3. To maintain your shaver in peak
condition, the blades should be oiled
every few haircuts.
Do not use hair oil,grease,oil mixed with
kerosene or any solvent. As the solvent
will evaporate and leave the thick oil which
may slow down the blades motion.
PRODUCTFEATURES
Battery Cover
Blade Cap
Nose Hair Trimmer
Outer Blade Housing
Power Switch
• Nose
• Off
• Shave/Trim
• Beard/Moustache
Trimmer
• Mini Shaver
Shaver Housing • Shaver Cap
INSTRUCTIONS FOR USE
Installing the Battery
Remove the Battery Cover and insert
2 AAA batteries (not included).
Make sure the positive (+)
and negative (-) ends of the
batteries are inserted in the
batterycompartment properly.
Replace the BatteryCoverand
clickinto place. Note: Do not
mix different types of batteries.
Do not mix old and new batteries.
Always dispose of batteriesproperly.
-
Using the NoseHair Trimmer
Remove the Blade Cap by twisting
it counterclockwise. Then, slide the
powerswitch to the “Nose”position.
Carefullyplace the blade into the nos
trilsto remove unwanted hair. Use the
same procedure to remove hair from
the earand also trim the eyebrows.
Using the MiniShaver
Remove the ShaverCap. Then, slide
the powerswitch to the “Shave/Trim”
position. Note: the Mini Shaver is for
small hairs. Hairs should be free of
lotion when using the Mini Shaver.
CLEANING AND MAINTENANCE
Be sure the Power Switch is turned off before cleaning
the device.
Cleaning the Nose Hair Trimmer
1. Switch the device off.
2. Remove the Outer Blade
Housing by twisting it counter
clockwise and raising it off
the unit.
3. Wipe the Outer Blade Housing
with a tissue to remove hairs,
dust, etc.
4. Replace the Outer Blade
Housing and twist it clockwise
to lock it in place.
Cleaning the Mini Shaver and Beard/Moustache Trimmer
1. Thoroughly brush and blow
any visible hairfrom the blades.
2. Remove the Shaver Housing
by holding the unit with the
trimmer side up and the blade
pointed away from you. Place
your thumb on the silver part
of the Mini Shaver and gently
press away from you. The
Housing will pop off for cleaning.
Note: You may rinse the Shaver
Housing with water. Do not let
waterdrain into the motor area.
TROUBLESHOOTING
If the cutters do not move, the cutting areas may be clogged
or dirty. Cleanthe bladesand make sure you have a fresh
set of batteriesinstalled.
CUSTOMER SERVICE
If you need any assistance with your 3-in-1 Smart Groomer,
please call 1 (877)714-7444, and select Option 3.
5. Do not allow water to drain in the
trimmer`s motor area.
4. Allow the Shaver Housing to
dry and replace it on the unit.
1C(K)
2 Folder
80g woodfree paper
F184URP1001
148x210mm (±2mm)
折叠后尺寸：74x105mm (±2mm)
0.1mm(±0.05mm)
75F184UR01
Manual
李先平
24/07/2014
DESIGN MATERIAL SPEC
Table of contents
