Shelfology Fat Lippie User manual

Fat Lippie Picture Ledge
Install Guide
Shelfology
Certied Rad™
Made In The U.S.A.
By Woodworkers, For
Woodworkers_

Required
Tools Optional Tools
Drill Level Stud Finder
¼" Diameter
Drill Bit Measuring
Tape
Pencil
Table of Contents Page
Installation Steps 004
Warnings 006
Rad Tips 007
5
GET MORE RADNESS NOW AT SHELFOLOGY.COM_ NEED A HAND? 949.244.1083 // [email protected]_
P.002
Fat Lippie Picture Ledge Install Guide Introduction

What’s In
The Box What You’ll Need
Create a minimal + rad
wall display with Fat
Lippie Picture Ledge.
Made in-house by us
in the United States of
Awesome. Rad!
Fat Lippie
Picture Ledge
1x
Wall Anchor
Set
1x
Innate Radness
Done!
Matching 1⁄"
Wall Fastener
Set
1x
P.003
CERTIFIED RAD™_
MADE IN THE U.S. OF A.
LIGHTNING FAST LEAD TIMES_
Fat Lippie Picture Ledge Install Guide
Introduction

Installation
Steps
001
002
003
Level the picture ledge and set second
matching 1 ⁄" fastener in opposite
end fastener hole with your drill. If the
fastener holes miss an available stud, see
Rad Tip ➀ on page 7. If you’ve already
installed blocking behind the length of
the backbar, skip to Step 5.
Woah! That's a wicked Fat Lippie you
have there! Position picture ledge on
the wall with the pre-drilled holes along
the top edge. Using a stud nder, align
fastener holes with as many studs as
possible. Use drill to fasten matching 1 ⁄"
fastener in either far left or right hole.
While the picture ledge is mounted to
the wall, mark every remaining empty
fastener hole with a pencil.
GET MORE RADNESS NOW AT SHELFOLOGY.COM_ NEED A HAND? 949.244.1083 // [email protected]_
P.004
Fat Lippie Picture Ledge Install Guide Installation Steps

Toggler® Anchors
Recommended
Remove the picture ledge from the wall
to install wall anchors in each marked
location that is not on a wall stud. Predrill
each wall anchor location with ¼" drill bit
to avoid breaking wall anchors.
Replace the picture ledge. Drill matching
1⁄" fastener into each fastener hole.
Make nal inspection of the picture
ledge. Check for picture ledge sag,
conrm the picture ledge is correctly
secured to wall. If your picture ledge is
sagging, refer to Rad Tip ➀ and ➁.
Stand back and relax, you did it! Give
your cat a celebratory fist bump, if
present. Gently place your Kenny G vinyl
collection on picture ledge and admire! If
you need more help, please reach out to
a shelf geek today.
[e-mail]
949.244.1083
004
006
005
007
P.005
CERTIFIED RAD™_
MADE IN THE U.S. OF A.
LIGHTNING FAST LEAD TIMES_
Fat Lippie Picture Ledge Install Guide
Installation Steps

Warnings
1.1 Picture ledges must
be correctly installed
into studs or wall
blocking. Failure to do
so may result in sagging
picture ledges, falling
objects, or serious
injury.
2.1 Every Shelfology
picture ledge length
has been engineered
for use with specic
ledge capacities/
dimensions. Failure to
follow our specied
capacity ratings and
correct picture ledge
dimensions may result
in sagging picture
ledges, falling objects,
or serious injury. Please
reference the Fat
Lippie Picture Ledge
Spec Sheet for more
information.
3.1 This product
contains chemicals
known to the State
of California to cause
cancer and birth defects
or other reproductive
harm. Don't eat this
picture ledge. If you live
outside of California,
do whatever you
want. For more boring
information, visit www.
p65warnings.ca.gov.
4.1 Any Shelfology
Certied Rad™ product
should be aunted with
caution around friends,
loved ones, and even
complete strangers,
as minimal or extreme
jealousy may occur.
Shelf responsibly.
➁
Adhere To
The Capacity
Rating Of
Your Specic
Picture Ledge
➂
California
Proposition 65
Warning
➃
This Product
May Make
Others
Incredibly
Jealous
➀
Correct Install
Required For
Safe Use
Whoa, you made it! We
are vicariously stoking
for you right now. Post
your sweet shele on
Instagram now!
@shelfology
#radshele
Need a hand? Speak with a
Shelf Geek at 949.244.1083 or
[e-mail] today.
How did we do? You’ll get
an email soon asking for a
product review, and we’d be
stoked if you oblige. You rock in
advance!
GET MORE RADNESS NOW AT SHELFOLOGY.COM_ NEED A HAND? 949.244.1083 // [email protected]_
P.006
Fat Lippie Picture Ledge Install Guide Warnings

1.1 Studs are the vertical
2x4 boards that make
up the bones of your
walls. They provide
solid structure for
your picture ledge to
attach to.
1.2 Blocking is typically
added later between
studs in the wall for
additional support to
mount picture ledges
to, and is usually made
from 2x4 or 2x6 lumber.
2.1 If your wall is not
straight, use shims to
ensure your picture
ledge is installed
straight across the wall
face and square to the
wall.
➁
Using Shims
to Straighten
Picture Ledge
➀
Fasten Into
All Studs
& Blocking
The Bracket
Crosses
90
P.007
CERTIFIED RAD™_
MADE IN THE U.S. OF A.
LIGHTNING FAST LEAD TIMES_
Fat Lippie Picture Ledge Install Guide
Rad Tips

Need a hand? Speak with a
Shelf Geek at 949.244.1083 or
[e-mail] today.
How did we do? You’ll get
an email soon asking for a
product review, and we’d be
stoked if you oblige. You rock
in advance!
© Shelfology 2023
Printed In The USA
TM