SHENZHEN ENCOM ELECTRIC TECHNOLOGIES CO. EDS780 Series User manual

Us e r s ’ M a n u a l
ISO9001Quality Management System Authentication
SHENZHEN ENCOM ELECTRIC TECHNOLOGIES CO., LTD.
Series Inverter
220V AC 0.75KW
EDS780 Series
Ver. : 1.2

www.enc.net.cn/en Tel/Fax:[phone] Content
CONTENT
1 Safety information and use notice points...........................................................1
1.1 Safety precautions..........................................................................................1
1.2 Use range .......................................................................................................2
1.3 Use notice points............................................................................................2
1.4 Scrap notice points.........................................................................................4
2 Type and specification of the inverter ................................................................5
2.1 Incoming inverter inspect ..............................................................................5
2.2 Type explanation............................................................................................5
2.3 Series type explanation..................................................................................5
2.4 Outer size and gross weight...........................................................................6
2.5 Basic running wiring diagram .......................................................................6
2.6 The inverter interface specifications .............................................................7
2.7 Operation and use of key board.....................................................................8
3 Function parameter schedule graph ..................................................................9
3.1 Symbol description ........................................................................................9
3.2 Function parameter schedule graph...............................................................9
4 Troubleshooting ..................................................................................................21
4.1 Failure and countermeasure.........................................................................21
4.2 Failure record lookup...................................................................................24
5 Maintenance........................................................................................................25
5.1 Routine maintenance ...................................................................................25
5.2 Inspection and replacement of damageable parts........................................25
5.3 Repair guarantee ..........................................................................................26
5.4 Storage .........................................................................................................26

www.enc.net.cn/en Tel/Fax:[phone] Safety information and use notice points
1
1 Safety information and use notice points
In order to ensure the safety of your personal and equipment, before using the
inverter, please read this chapter of contents conscientiously.
1.1 Safety precautions
There are four kinds of safe relevant warnings in this service manual, they are
as follows:
This symbol explains items that need to be paid attention to when being operated.
This symbol is briefed on some useful information.
This symbol briefs on: If does not operate on request, may make the body
injured or the equipment damaged.
This symbol briefs on: If does not operate on request, may cause death,
severely injured or serious property loss.
note
(1) Forbid to connect U, V, W output end to AC power supply, otherwise cause
the complete damage of the inverter.
(2) The inverter is forbidden to install on the flammables, otherwise have danger
of fire.
(3) Don't install it in the environment with explosive gas, otherwise have danger
of causing explosion.
(4) After connecting main loop, should carry on insulating treatment to bare
wiring end, otherwise have danger of getting an electric shock.
(5) If being connected to the power supply, don't operate the inverter with moist
hands, otherwise have danger of getting an electric shock.
(6) The ground terminal of the inverter must be grounded well.
(7) Inverter being connected to power supply, please don't open cover and carry
on wiring, can connect the wire or check only after closing power for 10
minutes.
(8) Only qualified personnel may carry on wiring and forbid leaving over any
conductive thing in machine, otherwise have danger of getting an electric
shock or causing damage of the inverter.
(9) Inverter stored for over half a year, should be stepped up gradually with
voltage regulator first while having the electricity, otherwise have danger of
getting electric shock and explosion.
danger
!
danger
!
warning
!
danger
!

www.enc.net.cn/en Tel/Fax:[phone] Safety information and use notice points
2
1.2 Use range
(1) This inverter is only suitable for three phases AC asynchronous motor in general
industrial field.
(2) While applying inverter to such equipments that relate much to the life, great
property, safety devices etc., must handle cautiously, and consult with producer,
please.
(3) This inverter belongs to the control device of general industrial motor, if used in
dangerous equipment, must consider the security safeguard procedures when the
inverter breaks down.
1.3 Use notice points
(1) EDS780 series inverter is voltage-type inverter, so temperature, noise and
vibration slightly increasing compared to power source running when using,
belongs to normal phenomenon.
(2) If need to run for a long time with constant torque of low-speed, must select
motor of frequency conversion for use. Use general asynchronous AC motor
when running at a low speed, should control temperature of the motor or carry
on heat dissipation measure forcedly, so as not to burn the generator.
(3) Such mechanical device needing lubricating as the gearbox and gear wheel, etc.,
after running at a low speed for a long time, may be damaged as lubrication
result become poor, please take necessary measure in advance.
(4) When the motor running with frequency above specified, besides considering the
vibration, noise increase of the motor, must also confirm speed range of the
motor bearing and the mechanical device.
(1) It is prohibited that connect AC220V signal to control ends except TA, TB,
TC, otherwise have danger of damaging property.
(2) If the inverter is damaged or without all parts, please don't install and operate
it, otherwise have danger of fire or cause personnel to be injured.
(3) When installing, should choose a place where can endure the inverter,
otherwise have danger of injuring personnel or damaging property while
falling down.
warning
!

www.enc.net.cn/en Tel/Fax:[phone] Safety information and use notice points
3
(5) For hoist and great inertia load, etc., the inverter would shut off frequently due to
over-current or over-voltage failure, in order to guarantee normal work, should
consider choosing proper brake package.
(6) Should switch on/off the inverter through terminal or other normal order
channels. It is prohibited that switch on/off the inverter frequently by using
strong electric switch such as magnetic control conductor, otherwise will cause
the equipment to be damaged.
(7) If need to install such switch as the magnetic control conductor, etc. between
inverter output and the motor, please guarantee the inverter is switched on/off
without output, otherwise may damage the inverter.
(8) The inverter may meet with mechanical resonance of the load within certain
range of frequency output, can set up jumping frequency to evade.
(9) Before using, should confirm the voltage of the power is within the working
voltage range allowed, otherwise should vary voltage or order special inverter.
(10) In the condition of altitude above 1000 meters, should use the inverter in lower
volume, reduce output current by 10% of specified current after each 1500
meters height increasing.
(11) Should make insulation check to the motor before using it for the first time or
after a long time placement. Please inspect with 500V voltage-type megohm
meter according to method shown as graph and insulation resistance should
not be smaller than 5 MΩ, otherwise inverter may be damaged.
(12) To forbid assembling capacitor for improving power factor or lightningproof
voltage-sensible resistance etc., otherwise will cause malfunction trip of the
inverter or damage of the parts, shown as graph 1-1.
(13) Remind: EDS780 inverter require long-term work at full capacity, the customer
must have an external cooling fan, or it may overheat protection fault and affect
the frequency normal life! (Inverter output current below 4A, noneed to use an
external fan.)

www.enc.net.cn/en Tel/Fax:[phone] Safety information and use notice points
4
Fig.1-1 frequency converter prohibit use of capacitor
1.4 Scrap notice points
When disposing scrap inverter and its parts, please note:
(1) The unit: please discard as industrial useless.
(2) Electrolytic capacitor: when burning the inverter electrolytic capacitor in it
may explode.
(3) Plastic: when plastic, rubber parts etc. in the inverter are burning, they may
bring bad, poisonous gas, so please be ready to safeguards.

www.enc.net.cn/en Tel/Fax:[phone] Type and specification of the inverter
5
2 Type and specification of the inverter
2.1 Incoming inverter inspect
(1) Check if there is damage during transportation and inverter itself has damage or fall-off
parts.
(2) Check if parts presented in packing list are all ready.
(3) Please confirm rated data of the inverter is in line with your order requirement.
Our product is guaranteed by strict quality system during manufacturing, packing,
transportation etc., please contact our company or local agent rapidly if some
careless omission or mistake arise, we’ll deal with it as soon as possible.
2.2 Type explanation
EDS780- 2 S 0007
Fig. 2-1 type description
2.3 Series type explanation
Table 2-1 series type explanation
Inverter type Rated power
（KVA）
Rated output
current（A）
Adapted motor
（KW）
EDS780-2S0007 1.8 4.7 0.75
Code Motor
(KW)
0007 0.75
Code Input volt.
S Single phase
Volt.grade Code
220V 2
Inverter serial no

www.enc.net.cn/en Tel/Fax:[phone] Type and specification of the inverter
6
2.4 Outer size and gross weight
Fig.2-2 Outline Image
Table 2-2 EDS780-2S0007mounting size
Inverter type W
(mm)
H
(mm)
D
(mm)
A
(mm)
B
(mm)
Fixing
aperture
(mm)
EDS780-2S0007 147.4 140.0 92.0 135.2 100 5
2.5 Basic running wiring diagram
Fig.2-3 Basic running wiring diagram
D
A
B
W
H
P+ PB
Braking resistor(external connection, selective asembly)
Built-in braking unit

www.enc.net.cn/en Tel/Fax:[phone] Type and specification of the inverter
7
2.6 The inverter interface specifications
Fig.2-4
(1) P1 terminal function description
item symbol name Function description Spec.
FWD Forward run
command
run
command REV Reverse run
command
Forward reverse run command,
see F5.08 group double-wire and
three-wire control function
description
X1 Multi-function input 1
X2 Multi-function input 2
X3 Multi-function input 3
Used for multi-function input
terminal, for detailed see function
parameter F5 group input end
function description.
Input impedance: R=2KΩ
Max. input frequency: 200Hz
VCC +5V power supply Provide +5V power supply.
(negative pole: GND)
Max. output current: 50mA
Multi-function input termina
GND +5V power supply
negative pole
Reference ground of analog
signal and +5V power supply
Analog value
input VCI Analog value input VCI Accept analog voltage input
Input voltage range:0~5V
(Input impedance:10 KΩ)
Resolution:1/1000

www.enc.net.cn/en Tel/Fax:[phone] Type and specification of the inverter
8
(2) P2 terminal function description
item symbol name Function description spec
485A 485 difference signal positive end
communication
485B
485
communication
interface 485 difference signal negative end
For standard 485
communication interface
please use twisted-pair or
STP
（3）P3 terminal function description：
Terminal label Terminal function description
P+
PB
External braking resistor: the resistance range of the braking resistor should not be
lower than 200Ω。
2.7 Operation and use of key board
Keypad is main unit for receiving command, displaying parameter. Outer dimension of
EN-KB5 is as Fig.2-5:
Fig.2-5 keypad layout sketch(EN-KB5)

www.enc.net.cn/en Tel/Fax:[phone] Function parameter schedule graph
9
3 Function parameter schedule graph
3.1 Symbol description
×---- parameter can’t be changed in process of running
○---- parameter can be changed in process of running
* ---- read-only parameter, unmodifiable
3.2 Function parameter schedule graph
F0 –basic run function parameter group
function
code name Set range unit Factory default
Modificat-
ion
F0.00 Frequency input
channel selection
0: keypad analog potentiometer setting
1: keypad digital setting
2: terminal UP/DOWN adjust setting (stored after
power off)
3: serial port setting
4: VCI analog setting (VCI-GND)
6: reserved
7: reserved
8: combination setting
9: terminal UP/DOWN adjust setting
(not stored after power off)
10:provision serial port (stored after power off)
1 1 ○
F0.01 Freq. digit setting Lower limit Freq.～upper limit Freq. 0.01Hz 50.00Hz ○
F0.02 Run command
channel selection
0: keypad run control
1: terminal run command control
(keypad stop command ineffective)
2: terminal run command control
(keypad stop command effective)
3: serial port run command control
(keypad stop command ineffective)
4: serial port run command control
(keypad stop command effective)
1 0 ○
F0.03 Run direction
setting
1st bit: 0, forward run; 1, reserved
2nd bit: 0, forward run allowed
1,reverserunbanned
3rd bit: REV/JOG key selection
0: as reverse run key
1: as jog key
1 100 ○
F0.04 Acce/Dece mode
selection
0: linear accelerating decelerating mode
1: S curve accelerating decelerating mode
1 0 ×
F0.05 S curve start
section time
10.0（％）－50.0（％）（Acce/Dece time）
F0.05+F0.06≤90（％） 0.1(％) 20.0(%) ○

www.enc.net.cn/en Tel/Fax:[phone] Function parameter schedule graph
10
F0.06 S curve rise time 10.0（％）－70.0（％）（Acce/Dece time）
F0.05+F0.06≤90（％） 0.1(％) 60.0(%) ○
F0.07 accelerating
decelerating time
unit
0: second
1: minute 1 0 ×
F0.08 Acce time 1 0.1－6000.0 0.1 20.0 ○
F0.09 Dece time 1 0.1－6000.0 0.1 20.0 ○
F0.10 Upper limit freq. Lower limit freq.－400.00Hz 0.01Hz 50.00Hz ×
F0.11 Lower limit freq. 0.00－Upper limit freq. 0.01Hz 0.00Hz ×
F0.12 Lower limit freq.
run mode
0: run at lower limit freq.
1: stop running 1 0 ×
F0.13 Torque boost
mode
0: manual boost
1: automatic boost 1 0 ○
F0.14 Torque boost 0.0－20.0（％） 0.1(%) 4.0(%) ○
F0.15 V/F curve setting 0: constant torque curve
1: degressive torque curve 1（the 2.0nd power）
2: degressive torque curve 2（the 1.7th power）
3: degressive torque curve 3（the 1.2th power）
1 0 ×
F0.16 reserved 1 0 ×
F1 –start-up, stop, brake function parameter group
Function
code name Set range unit Factory default
Modificat-
ion
F1.00 Start-up run mode 0: start at start-up freq.
1: first brake, then start at start-up freq.
2: reserved
1 0 ×
F1.01 Start-up freq. 0.0－10.00Hz 0.01Hz 0.00Hz ○
F1.02 Start-up freq. duration 0.0－20.0S 0.1s 0.0s ○
F1.03 Zero freq. DC braking volt. 0－15（％） 1 0 ○
F1.04 Zero freq. DC braking time 0.0－20.0S 0.1s 0.0s ○
F1.05 Stop mode 0: Dec stop
1: free stop
2: Dec＋DC brake stop
1 0 ×
F1.06 DC brake initiative freq.
when stop running
0.0－15.00Hz 0.01Hz 0.00Hz ○
F1.07 DC brake time when stop
running
0.0－20.0s 0.1s 0.0s ○
F1.08 DC brake voltage when stop
running
0－15（％） 1 0 ○
F2 –auxiliary run function parameter group
Function name Set range unit Factory modif-

www.enc.net.cn/en Tel/Fax:[phone] Function parameter schedule graph
11
code default ication
F2.00 Analog filter time
constant
0.00－30.00s 0.01s 0.20s ○
F2.01 Forward reverse run
dead-section time
0.0－3600.0s 0.1s 0.1s ○
F2.02 Automatic energy
save run
0: no action
1: action 1 0 ×
F2.03 AVR function 0: no action
1: action all the time
2: no action only during Dec
1 0 ×
F2.04 Slip frequency
compensation
0～150(％)0-no slip frequency
compensation 1 0 ×
F2.05 Carrier wave
freq.
1－10.0K
0.1K depend on
machine type ×
F2.06 Jog run frequency 0.10－50.00Hz 0.01Hz 5.00Hz ○
F2.07 Jog Acce time 0.1－60.0s 0.1s 20.0s ○
F2.08 Jog Dece time 0.1－60.0s 0.1s 20.0s ○
F2.09 reserved 1 0 ×
F2.10
Principal subordinate
Machine communication
frequency provision
proportion
0（％）－500（％）
1(%) 100(%) ○
F2.11 LED display
control 1
0000-1111
first bit: running time
0: not display
1: display
second bit: accumulative time
0: not display
1: display
third bit: input terminal status
0: not display
1: display
kilobit(fourth bit): output terminal status
0: not display
1: display
1 1111 ○
F2.12 Reserved
F2.13 Parameter operation
control
LED 1st bit:
0: all parameter allowed to be modified
1: except this parameter，all other parameter
not allowed to be modified
2: except F0.01 and this parameter，all other
parameter not allowed to be modified
LED 2nd bit:
0: no action
1: restore default value
2: clear history failure record
LED 3rd bit:
0: lock all buttons
1: lock all buttons but not STOP key
1 0 ×

www.enc.net.cn/en Tel/Fax:[phone] Function parameter schedule graph
12
2: lock all buttons but not ，STOP key
3: lock all buttons but not RUN, STOP key
4: lock all buttons but not SHIFT, STOP key
F2.14 Communication
configuration
LED first bit: baud rate selection
0: 1200BPS
1: 2400BPS
2: 4800BPS
3: 9600BPS
4: 19200BPS
5: 38400BPS
LED second bit: data format
0: 1－8－1format, no checkout
1: 1－8－1 format, even checkout
2: 1－8－1 format, odd checkout
1 03 ×
F2.15 Local address 0 －127, 127 is broadcast address. The
inverter only receive but not send when it is
set to be 127, 0 is address for main device.
1 1 ×
F2.16 Communication overtime 0.0－1000.0s 0.1s 0.0s ×
F2.17 Local responsion delay 0－1000ms 1ms 5ms ×
F2.18 Acce time 2 0.1－6000.0 0.1 20.0 ○
F2.19 Dece time 2 0.1－6000.0 0.1 20.0 ○
F2.20 Acce time 3 0.1－6000.0 0.1 20.0 ○
F2.21 Dece time 3 0.1－6000.0 0.1 20.0 ○
F2.22 Acce time 4 0.1－6000.0 0.1 20.0 ○
F2.23 Dece time 4 0.1－6000.0 0.1 20.0 ○
F2.24 Acce time 5 0.1－6000.0 0.1 20.0 ○
F2.25 Dece time 5 0.1－6000.0 0.1 20.0 ○
F2.26 Acce time 6 0.1－6000.0 0.1 20.0 ○
F2.27 Dece time 6 0.1－6000.0 0.1 20.0 ○
F2.28 Acce time 7 0.1－6000.0 0.1 20.0 ○
F2.29 Dece time 7 0.1－6000.0 0.1 20.0 ○
F2.30 Multisection freq. 1 Lower limit freq.－upper limit freq. 0.01Hz 5.00Hz ○
F2.31 Multisection freq. 2 Lower limit freq.－upper limit freq. 0.01Hz 10.00Hz ○
F2.32 Multisection freq. 3 Lower limit freq.－upper limit freq. 0.01Hz 20.00Hz ○
F2.33 Multisection freq. 4 Lower limit freq.－upper limit freq. 0.01Hz 30.00Hz ○
F2.34 Multisection freq. 5 Lower limit freq.－upper limit freq. 0.01Hz 40.00Hz ○
F2.35 Multisection freq. 6 Lower limit freq.－upper limit freq. 0.01Hz 45.00Hz ○
F2.36 Multisection freq. 7 Lower limit freq.－upper limit freq. 0.01Hz 50.00Hz ○
F2.37 Multisection freq. 8 Lower limit freq.－upper limit freq. 0.01Hz 5.00Hz ○
F2.38
~
F2.44
Reserverd
F2.45 Jumping freq. 1 0.00－400.00Hz 0.01Hz 0.00Hz ×
F2.46 Jumping freq. 1 range 0.00－30.00Hz 0.01Hz 0.00Hz ×

www.enc.net.cn/en Tel/Fax:[phone] Function parameter schedule graph
13
F3 group –closed-loop run function parameter group
Function
code name Set range unit Factory default
modif-
ication
F3.00 Closed-loop run
control selection
0: closed-loop control ineffective
1: PID closed-loop control effective
2: reserved
1 0 ×
F3.01 Provision channel
selection
0: digital provision
1: VCI analog 0－5V voltage provision
2: reserved
3: keypad analog potentiometer provision
1 1 ○
F3.02 Feedback channel
selection
0: VCI analog input voltage 0－5V
1: reserved
1 1 ○
F3.03 Specified value digital
setting 0.00－10.00V 0.01 0.00 ○
F3.04 Minimum specified value 0.0－maximum specified value; percentage
relative to 10.00V 0.1(%)0.0(%) ○
F3.05 feedback value
responding to
minimum specified value
0.0(%)－100.0(%) 0.1(%)0.0(%) ○
F3.06 maximum specified
value Minimum specified value－100.0（％） 0.1(%)100.0(%) ○
F3.07 feedback value
responding to
maximum specified
value
0.0（％）－100.0（％） 0.1(%)100.0(%) ○
F3.08 proportion gain Kp 0.000－9.999 0.001 0.050 ○
F3.09 Integral gain Ki 0.000－9.999 0.001 0.050 ○
F3.10 Differential gain Kd 0.000－9.999 0.001 0.050 ○
F3.11 Sampling cycle T 0.01－1.00s 0.01s 0.10s ○
F2.47 Jumping freq. 2 0.00－400.00Hz 0.01Hz 0.00Hz ×
F2.48 Jumping freq. 2 range 0.00－30.00Hz 0.01Hz 0.00Hz ×
F2.49 Jumping freq. 3 0.00－400.00Hz 0.01Hz 0.00Hz ×
F2.50 Jumping freq. 3 range 0.00－30.00Hz 0.01Hz 0.00Hz ×
F2.51 Setting run time 0－65535 hours 1 0 ○
F2.52 Accumulative run time 0－65535 hours 1 0 *
F2.53 RS485communication
frame format selection
0: a ASCII frame of 14 byte or 18 byte
1: a hex frame of 8 byte or 10 byte, original
response not changed
2: a hex frame of 8 byte or 10 byte, 12
command has no response
3: a hex frame of 8 byte or 10 byte, 14
command has no response
4: a hex frame of 8 byte or 10 byte, both 12
and 14 command have no response
1 0 ×

www.enc.net.cn/en Tel/Fax:[phone] Function parameter schedule graph
14
F3.12 Deviation margin 0.0－20.0（％）percentage relative to 10.00V 0.1(%) 2.0(%) ○
F3.13 Integral separation PID
adjusting threshold 0.0－100.0% 0.1(%) 100.0(%) ○
F3.14 Closed-lop preset
frequency 0－upper limit frequency 0.01Hz 0.00Hz ○
F3.15 Closed-loop preset
frequency holding
time
0.0-6000s 0.1s 0.0s ○
F3.16
~
F3.26
Reserved
F3.27 Closed-loop adjusting
characteristic
0: Forward function
1: Reverse function
1 0 ○
F3.28 LED initial
supervision parameter
selection
0: set frequency
1: output frequency
2: output current
3: output voltage
4: DC bus bar voltage
5: motor speed
6: heat sink temperature
7: run time
8: accumulative run time
9: input terminal status
10: output terminal status
11: analog input VCI/PID provision
1 1 ○
F3.29 Zero freq. braking freq.
at starting 0.00Hz-15.00Hz 0.01Hz 0.00 Hz ○
F3.30 Failure relay TA, TC
function selection
0: inverter running（RUN）
1: frequency arriving signal（FAR）
2: frequency level detect signal (FDT1)
3: reserved
4: overload warning alarm signal (OL)
5: output frequency reach high limit（FHL）
6: output frequency reach low limit（FLL）
7: inverter under voltage blockage stop (LU)
8: external failure stop-running（EXT）
9: inverter zero speed running
10: PLC running
11: simple PLC section running finished
12: PLC finish a cycle running
13: reserved
14: inverter ready to run (RDY)
15: inverter failure
16: traverse high and low limit restriction
17: interior counter reach final value
18: interior counter reach specified value
19: set run time arriving
20: interior timing arriving
21~24: reserved
15 ○
F3.31 VCI analog input gain 0-800% 100 ○

www.enc.net.cn/en Tel/Fax:[phone] Function parameter schedule graph
15
F4 –simple PLC function parameter group
Function
code name Set range unit Factory default
modifi
cation
F4.00 Simple PLC
running setting
LED first bit:
0: no action
1: stop after single circulation
2: keep final value after single circulation
3: consecutive circulation
LED second bit:
0: start again from first section
1: continue to run at mid-section frequency
LED third bit: PLC run time unit
0: second
1: minute
1 000 ×
F4.01 Section 1 setting 000－621
LED first bit: frequency setting
0: multi-section freq. i (i=1~7)
1: freq. determined by F0.00 function code
LED second bit: run direction selection
0: forward run
1: reverse run
2: determined by run command
LED third bit: Acc/Dec time selection
0: Acce/Dece time 1
1: Acce/Dece time 2
2: Acce/Dece time 3
3: Acce/Dece time 4
4: Acce/Dece time 5
5: Acce/Dece time 6
6: Acce/Dece time 7
1 000 ○
F4.02 Section 1 run time 0－6000.0 0.1 10.0 ○
F4.03 Section 2 setting 000－621 1 000 ○
F4.04 Section 2 run time 0－6000.0 0.1 10.0 ○
F4.05 Section 3 setting 000－621 1 000 ○
F4.06 Section 3 run time 0－6000.0 0.1 10.0 ○
F4.07 Section 4 setting 000－621 1 000 ○
F4.08 Section 4 run time 0－6000.0 0.1 10.0 ○
F4.09 Section 5 setting 000－621 1 000 ○
F4.10 Section 5 run time 0－6000.0 0.1 10.0 ○
F4.11 Section 6 setting 000－621 1 000 ○
F4.12 Section 6 run time 0－6000.0 0.1 10.0 ○
F4.13 Section 7 setting 000－621 1 000 ○
F4.14 Section 7 run time 0－6000.0 0.1 10.0 ○

www.enc.net.cn/en Tel/Fax:[phone] Function parameter schedule graph
16
F5 –terminal correlative function parameter group
Function
code name Set range unit Factory default
modifi
cation
F5.00 Input terminal X1
function selection
0: leave control terminal unused
1: multi-section speed control terminal
2: multi-section speed control terminal
3: multi-section speed control terminal
4: multi-section speed control terminal
5: external forward run jog control
6: external reverse run jog control
7: Acce/Dece time option terminal 1
8: Acce/Dece time option terminal 2
9: Acce/Dece time option terminal 3
10: external device failure input
11: external reset input
12: free stop input
13: external stop-running order
14: stop DC braking input command DB
15: inverter run banned
16: frequency increasing control (UP)
17: frequency degression control (DOWN)
18: Acc/Dec ban command
19: three-line run control
20: closed-loop ineffective
21: PLC ineffective
22: simple PLC pause control
23: PLC stop status reset
24: frequency provision channel option 1
25: frequency provision channel option 2
26: frequency provision channel option 3
27: frequency switched to CCI
28: command switched to terminal
29: run command channel option 1
30: run command channel option 2
31: run command channel option 3
32: traverse jump-in
33: external interruption input
34: interior counter reset end
35: interior counter triggering end
36: interior timer reset end
37: interior timer triggering end
38: reserved
1 0 ×
F5.01 Input terminal X2
function selection
Same as above ×
F5.02 Input terminal X3
function selection
Same as above ×
F5.03 reserved
F5.04 reserved
F5.05 reserved
F5.06 reserved

www.enc.net.cn/en Tel/Fax:[phone] Function parameter schedule graph
17
F5.07 reserved
F5.08 FWD/REV run mode
selection
0: double-line control mode 1
1: double-line control mode 2
2: three-line control mode 1
3: three-line control mode 2
1 0 ×
F5.09 UP/DOWN velocity 0.01－99.99Hz/s 0.01Hz/s 1.00Hz/s ○
F5.10 Reserved
F5.11 reserved
F5.12 reserved
F5.13 reserved
F5.14 Frequency arriving
(FAR) checkout scope
0.00－50.00Hz 0.01Hz 5.00Hz ○
F5.15 FDT1 (frequency
level) electric level
0.00－high limit frequency 0.01Hz 10.00Hz ○
F5.16 FDT1 lag 0.00－50.00Hz 0.01Hz 1.00Hz ○
F5.17 Reserved
F5.18 Analog output (AO) gain 0.00－2.00 0.01 1.00 ○
F5.19 Analog output (AO) offset 0.00－10.00V 0.01 0.00 ○
F5.20 reserved
F5.21 reserved
F5.22 reserved
F5.23 reserved
F5.24 reserved
F5.25 Set interior counting value
reaches provision
0--9999 1 0 ○
F5.26 Specified interior counting
value reaches provision
0--9999 1 0 ○
F5.27 Interior timer setting 0.1－6000.0s 0.1 60.0 ○
F6 –traverse special function parameter group
Function
code name Set range unit Factory default
modifi
cation
F6.00
～
F6.07
Reversed
F7–frequency provision function parameter group
Function
code name Set range unit Factory default
modifi
cation
F7.00 VCI min. provision 0.00－F7.02 0.01V 0.00V ○
F7.01 VCI min. provision corresponding freq. 0.00－high limit frequency 0.01Hz 0.00Hz ○