SHENZHEN FLYING INDUSTRY DEVELOPMENT W-01 User manual

SHENZHEN FLYING INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
Wireless Infrared Motion Detector W-01(Model 0010019)
Package:
1 x Wireless infrared motion detector
1 x Bracket
1 x User manual
Feature:
Model: 0010019 (W-01)
Size: 100mm x 60mm x 40mm, antenna not included
Working distance: 100 m (Open field)
Detection distance: 10 m
Detection range: Fan-shaped angle 110°
Decode: Fixed code by Pins
Alarm time: 2 seconds
Battery: 6F22-9V battery (Included, useful life time 6-12 months).
Indication of low battery
Installation:
When installing it, choose the favorable locations according to the environment. The lens should face the designated surveillance locations.
The height of installation should be about 2 meters above the ground.
Using screws to fix the bracket on the wall and put the detector on the bracket, then adjust the detector to the suitable angle of 10~14°. (See Side
View)
Note A: Don't put the detector towards lighting, sunshine or the computer.
Note B: Don't put the detector in an environment of strong wind, steam, oil smoke or be exposed to high temperature.
Note C: Don't put any barriers in the detecting area.
Note D: Don’t install 2 infrared movement detectors within a small space.
Usages:
Pull out the antenna of the movement detector.
Push down the power switch of the movement detector to position "ON". After 60 seconds delay, the movement detector will enter into the
automatic detection state.
Within the area of detection, the movement detector will be triggered by any movement, LED will turn on green light for 2 seconds, and the
movement detector will send alarming message to the main unit.
Indication of low battery: When the voltage of battery is less than 6V, LED will straightly turn on red light. At this time, you must immediately
change the battery.
Side View
10~14 o
0
2 M
10 M
Detecting area
110 o
Detecting area
Top View

SHENZHEN FLYING INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [e-mail]
Note:
①Power Switch
②Pins Area: (See Chart 1.a)
Central Code: Total 8 rows A0 ~ A7, each row has three pins, each row pins indicates a code number, such as 0, 1 or 2, it is an 8 numbers
code. The central code in chart 1.a is 00022100. (See Chart 1.b for the mode of central code)
Zone Code: Total 4 rows D0 ~ D3, each row has two pins, each row pins indicates a code number, such as 1 or 2, it is a 4 numbers code.
The zone code in chart 1.a is 1121. (See Chart 1.c for the mode of zone code)
③Interval time: (See Chart 2)
Between two detections, select the interval time at 8 seconds or 150 seconds. The interval time in chart 2.a is 8 seconds while in chart 2.b is
150 seconds. The parameter should be set to 8 seconds, please DO NOT change it.
ON
OFF
PT2264
DC 9V - 6F22 Battery
_
+
③
②
①
H N L
A3
A0
A1
A2
A4
A5
A6
A7
D0
D1
D2
D3
Lens
LED
Chart 1.a
Chart 2.b
Interval time: 150 s
Chart 2.a
Interval time: 8 s
Chart 1.b
Mode of central code
H
L
N
Code : 0
H
L
N
Code : 2
H
L
N
Code : 1
Chart 1.c
Mode of zone code
H
N
Code: 1
H
N
Code: 2
H N L
A3
A0
A1
A2
A4
A5
A6
A7
D0
D1
D2
D3
Central Code
Zone Code