Shenzhen Ousent Technologies CO.,LTD OS-MC12-SFP User manual

深圳市欧深特信息技术有限公司
Shenzhen Ousent Technologies CO.,LTD
Add: Floor 2 Building 1 Shunheda Industrial Area. 72Block Baoan District. Shenzhen City Guangdong P.R. CHINA
Tel: [phone] Fax: [phone] ext 808
Website: www.ousent.com
1
Brief introduction
Many thanks for purchasing 10/100/1000M SFP Fiber Ethernet Media Converter!
This product supports IEEE802.3u 1000Base-Tx/Fx protocol, as well as full duplex and half duplex mode. Be designed with a switch
controller and buffer memory that connect two types segments operation smoothly. IT can be used as standalone unit or as slide-in
module to the 19 Inch Converter Rack Chassis ( only for external power product).
This manual is for 10/100/1000M SFP Media Converter. The following purchasing guide is for customer’s reference.
Purchasing guide for optical transceivers
Model
Specifications
OS-MC12-SFP
10/100/1000M adaptive，SFP Media Converter
Packing list
Please check the following items in the package before installing the transceiver.
Packing Item
Quantity
Fiber Ethernet SFP Media Converter
1 SET
AC/DC adapter (for external power unit only)
1 PCS
Power line (for internal power unit only)
1 PCS
User manual
1 COPY
10/100/1000M SFP Fiber Media Converter
User Manual
Please contact the dealer immediately for any loss or damage to the above items.

深圳市欧深特信息技术有限公司
Shenzhen Ousent Technologies CO.,LTD
Add: Floor 2 Building 1 Shunheda Industrial Area. 72Block Baoan District. Shenzhen City Guangdong P.R. CHINA
Tel: [phone] Fax: [phone] ext 808
Website: www.ousent.com
2
1.Interface
RJ-45 interface
The transmission media adopts CAT5 twisted-pair with typical length of 120 meter.
It features the function of automatically identifying the through line and cross wire.
Fiber interface
SFP fiber interface is of duplex mode type, including two interfaces, namely TX and RX. When the two sets of optical transceiver are
interfaced or connected to switch with fiber interface, the fiber is in cross connection, namely TX-RX,RX-TX(direct butting for single
optical fiber).
2.Connection
The network device(work station, hub or switch) with RJ-45 interface is connected to RJ-45 jack of optical transceiver through
twisted-pair .And the multi/single mode fiber is connected to SFP fiber interface of the optical transceiver. Then switch on. The
corresponding LED is on for correct connection.(See the table below for the LED indicator lamp)
Figure 2 Schematic of Real panel for SFP fiber Module
Explanation for LED indicator lamp
LED indicator lamps serve as device monitoring and trouble display. The following is the explanation for each LED indicator lamp.
LED
function
status
describing
100
UTP port speed LED
on
100M speed
off
Not 100M speed
1000
UTP port speed LED
on
1000M speed
off
Not 1000M speed
TL/A
(TX-LINK/ACT)
UTP port
link/action status LED
on
Link is ok
off
Link is fail
blink
Data is been received or transmitted
FDX
UTP port duplex LED
on
Full duplex
off
Half duplex
FL/A
(FX-LINK/ACT)
Fiber port
link/action status LED
on
Fiber link is ok
off
Fiber link is fail
blink
Data is been received or transmitted
POWER
Power LED
on
Power is on
off
Power is fail
Installation

深圳市欧深特信息技术有限公司
Shenzhen Ousent Technologies CO.,LTD
Add: Floor 2 Building 1 Shunheda Industrial Area. 72Block Baoan District. Shenzhen City Guangdong P.R. CHINA
Tel: [phone] Fax: [phone] ext 808
Website: www.ousent.com
3
Transmission characteristics of double fiber transceiver
Product model
Optical wavelength
Optical power
Sensitivity
Transmission distance
OS-MC12-SFP
Decide by the SFP module you selected
Main features
1. In conformity to IEEE802.3 10 Base-T standard ,as well as to IEEE802.3u 100 Base-TX/FX standard.
2. Max 2M buffer memory built-in chip.
3. Back pressure flow control for full duplex. IEEE802.3x and half duplex.
4. Automatic identification of MDI/MDI-X cross line.
5. High-performance 1.4Gbps memory bandwidth.
6. In conformity to safety code of FCC 15 CLASS A and CE MARK.
Technical parameters
1. Standard protocol
IEEE802.3 IEEE802.3u and IEEE802.3x standard.
2. Connector: one UTP RJ-45 connector, one SC/ST connector.
3. Operation mode: full duplex mode or half duplex mode.
4. Power supply parameter: outside 5V DC 2A or built-in 110-265V AC.
5. Environmental temperature: -10℃～70℃.
6. Power consumption: 3.5W
7. Relative humidity: 5%-90%
8. TP cable:CAT5 UTP cable
9. Transfer fiber:
multi-mode: 50/125, 62.5/125 or 100/140um
single mode: 8.3/125, 8.7/125, 9/125 or 10/125um
Fiber transmission features

深圳市欧深特信息技术有限公司
Shenzhen Ousent Technologies CO.,LTD
Add: Floor 2 Building 1 Shunheda Industrial Area. 72Block Baoan District. Shenzhen City Guangdong P.R. CHINA
Tel: [phone] Fax: [phone] ext 808
Website: www.ousent.com
4
94mm(L)*70mm(W)*25mm(H) (for outside power)
140mm(L)*110mm(W)*30mm(H) (for built-in power)
Mechanical Dimensions

深圳市欧深特信息技术有限公司
Shenzhen Ousent Technologies CO.,LTD
Add: Floor 2 Building 1 Shunheda Industrial Area. 72Block Baoan District. Shenzhen City Guangdong P.R. CHINA
Tel: [phone] Fax: [phone] ext 808
Website: www.ousent.com
5
1. This product is suitable for indoor application.
2. Put on the dust cover of fiber interface when not used.
3. Verify the product power supply conforms to your country AC power requirement before insert the power plug
4. It is forbidden to stare at the TX fiber-transfer end with naked eyes.
Trouble shooting
1.Device is not matched. Please select the corresponding network device according to the transfer rate of the product (10Mbps or
100Mbps or 1000M) when connected to other network devices(network card ,hub, switch).
2.Line loss is excessive during the fiber wiring. Excessive loss in connector plug-in and fiber soldering wedding, and excessive
intermediate nodes may cause excessive loss rate or abnormal operation.
Appendix
UTP complies with IEEE802.3 Standards, and has two types: T568A T568B.
Parallel cable: connect T568A to T568A , or T568B to T568B
Crossing cable: connect T568A to T568B
Note: Connecting to Router, Bridge or Switch, please refer to the device Technical Manual.
Notice:
Ousent reserves the right to make changes to or discontinue any optical link product or service identified in this publication without
notice in order to improve design and or performance.
Applications that are described herein for any of the optical link products are for illustrative purposes only. Ousent makes no
representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Contact:
Add: Floor 2 Building 1 Shunheda Industrial Area. 72Block Baoan District. Shenzhen City Guangdong P.R. CHINA
Tel: [phone]
Fax: [phone] ext 808
Postal:518057
E-mail:[email protected]
Website: www.ousent.com
Cautions