Sherlotronics WMTX Quick start guide

Code-Hopping Encryption Dual code
Audible Piezo output
Weather-proof ABS housing
Over-moulded easy to press Button
3V Long Life Lithium battery
Frequency stability controlled +/- 75KHz
Order Codes:
This product is approved for use in Residential, commercial and
Light Industrial Environment and Complies with the essential
protection requirements of the R&TTE Directive 1999/EC on the
approximation of the laws of the Member states relating to
electromagnetic compatibility and radio spectrum.
Certifications:
ETSI EN300 220-V2.4.1
ETSI EN301-489-3 V1.4.1
ETSI EN301-489-1 V1.9.2
IEC 60950-1:2005 + A1:2009
Wall Mount Transmitter
(Weather proof)
Approvals:
III
Model:
Encryption type:
Transmission frequency:
Transmission method:
Transmission range:
Voltage range:
Battery type:
Sleep mode current consumption:
Current consumption on TX:
Operating Temperature:
Dimension (lxbxh)
Gross weight:
WMTX
Code hopping (Dual code)
403 / 433MHz
OOk
150m (Open air) 40m (indoors)
2.0V to 3.6 VDC
CR2450 Lithium
< = 1uA
< = 20mA
-7°C to 49°C
60 x 60 x 25mm
55g
Technical Specifications:
Features:
Model No: WMTX
Installation Instructions - For Service Persons Only
For more info visit our web site: www.sherlotronics.com
1 Ch Wall mount Transmitter
3V Lithium Battery CR2450
Spare WMTX Casing ABS
WMTX
CR2450
WM_ABS
English
W M T X

1. Unscrew the base plate
2. Remove the battery carefully pushing it out the battery holder towards the middle of the PCB
3. Install a new battery Positive (+) facing upwards.
4. Test the unit is operating before closing the housing the unit should beep when the button is pressed
Mount the unit in an upright position with the SHERLOTRONICS logo facing the bottom.
Avoid mounting on Metal surfaces and near High Power cables. If mounting in a shower or very wet
environment, apply a small amount of silicone over the screw holes to seal the unit completely.
Please follow the relevant Receivers Installation instructions to programming the unit to a receiver.
The WMTX is compatible to the following Receiver models:
Model: RX1-150; Model: RX2-150; Model: Rx3-150; Model: RX1-500
Model: RX4-500; Model: MB4000
Please Note: Only for Models manufactured Nov 2016 onwards.
If your are learning the WMTX into an Old generation receiver and it does not want to program in then you can
revert the WMTX unit to transmit out our Old generation Receiver code.
Follow this procedure to configure the unit with the Old code:
1. Open the WMTX unit up and remove the battery.
2. While pressing in the button, insert the battery and keep pressing the button for about 10 seconds.
The WMTX will then beep when it is ready.
1 Beep = Old Code
2 Beeps = New code
You can alternate between the old code and the new code by following the procedure above.
CAUTION:
RISK OF EXPLOSION IF THE BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO INSTRUCTIONS.
Location & Mounting
Replacing the Batteries
The unit is supplied with a CR2450 3V Lithium battery. The battery is rated at 610mA/h. The WMTX will be able
to transmit over 40 000 times before the battery is depleted. The unit will loose RF performance when the battery
reaches below 2.6V DC. It is best to change the battery every 3 years if not used very often for instance if it is
used as a PANIC button. If the unit is used as a Door opener in a busy office environment then we would
recommend replacing the battery every year.
Programming to a Receiver
Warranty
This product is sold subject to our standard warranty conditions and is warrantied against defects in workmanship
for a period of two years (batteries excluded)
Customer Support line: [phone] E-mail: [email protected]