Panduit Atlona AT-HDVS-200-TX User manual

1
Installation Guide
AT-HDVS-200-TX / AT-HDVS-200-TX-PSK
Three-Input HDBaseT Transmitter for HDMI and VGA
AT-HDVS-200-TX / AT-HDVS-200-TX-PSK
The Atlona AT-HDVS-200-TX is a 3×1 switcher and HDBaseT transmitter with two HDMI inputs
and a VGA input with audio. Video signals up to 4K/UHD @ 60 Hz with 4:2:0 chroma subsa-
mpling, plus embedded audio, control, and Ethernet can be transmitted up to 330 feet (100
meters). The two-channel audio input can be assigned to any of the video inputs and embedded
for HDBaseT transmission. The HDVS-200-TX is designed for use with the AT-OME-RX21 4K
scaling receiver, but can also be used with Atlona switchers and matrix switchers with HDBaseT
inputs. This transmitter can serve as an integral component of a fully automated AV system, with
the convenience of automatic input selection and display control. It is remotely powered by the
OME-RX21 or other Atlona devices over HDBaseT.
The AT-HDVS-200-TX-PSK is identical to the AT-HDVS-200-TX, with the addition of local power-
ing capability and an external power supply.
IMPORTANT: Visit https://www.atlona.com/product/AT-HDVS-200-TX or
https://www.atlona.com/product/AT-HDVS-200-TX-PSK for the latest rmware
updates and Installation Guide.
1 x AT-HDVS-200-TX
1 x Captive screw connector, 3-pin
1 x Mounting brackets
1 x Installation Guide
1 x AT-HDVS-200-TX-PSK
1 x Captive screw connector, 3-pin
1 x 48V DC power supply
1 x Mounting brackets
1 x Installation Guide
AT-HDVS-200-TX AT-HDVS-200-TX-PSK
Package Contents

2
Installation Guide
AT-HDVS-200-TX / AT-HDVS-200-TX-PSK
1 INPUT
Press this button to cycle through each of
the available inputs: HDMI IN 1, HDMI IN
2, and VGA IN.
2 VOL/UP
Press this button to adjust the volume on
the connected display. Refer to the User
Manual for more information.
3 DISPLAY
Press this button to trigger user-
dened RS-232/CEC/IP display control
commands. Refer to the User Manual for
more information.
4 VOL/DOWN
Press this button to adjust the volume on
the connected display. Refer to the User
Manual for more information.
5 HDMI IN 1
Connect an HDMI cable from this port to
an HD source.
6 VGA IN
Connect a VGA cable from this port to a
VGA source.
7 VGA
This LED indicator will glow bright green
when the VGA IN port is selected.
8 PW
This LED indicator will glow bright green
when the switcher is powered.
9 AUDIO IN
Connect a 3.5mm mini-stereo audio cable,
from an analog audio source, to this port.
10 HDMI 1
This LED indicator will glow bright green
when the HDMI IN 1 port is selected.
11 HDMI 2
This LED indicator will glow bright green
when the HDMI IN 2 port is selected.
12 FW
Connect a mini USB to USB-A type cable
from this port to a computer to update the
rmware.
Refer to the User Manual for more
information.
13 DC 48V
Connect the power supply to this port to
power an HDBaseT receiver, projector, or
other PoE device.
14 RS-232
Connect the included 3-pin captive screw
from this connector to an RS-232 control
device.
15 HDMI IN 2
Connect an HDMI cable from this port to
an HD source.
16 LAN
Connect an category cable from this port
to the network.
17 HDBaseT OUT
Use an category cable to connect an
HDBaseT PoE receiver to this port.
HDMI IN 2
RS-232
RX
RL
TX
PW
HDMI
INPUT
DISPLAY
v
v
AT-HDVS-200-TX
VOL
HDMI IN 1 VGA IN AUDIO IN
1
2
VGA
FW RS-232
HDMI IN 2 LAN HDBaseT OUT
RS-232
RX
TX
HDMI IN 2
RS-232
RX
RL
TX
PW
HDMI
INPUT
DISPLAY
v
v
AT-HDVS-200-TX
VOL
HDMI IN 1 VGA IN AUDIO IN
1
2
VGA
FW RS-232
HDMI IN 2
DC 48V LAN HDBaseT OUT
RS-232
RX
TX
+
Panel Descriptions
NOTE: The DC 48V port is only
available on the AT-HDVS-200-
TX-PSK.
1 2 7 108 9 12 13
14 15 16 173 4 5 6 11
Front Rear

3
Installation Guide
AT-HDVS-200-TX / AT-HDVS-200-TX-PSK
Black
White
48 V DC
power supply
Locate the included orange captive screw connector and wire the included power supply to the
block, as shown below. Do not use high-torque devices, when securing the wires to the captive
screw connector, as this may damage the screws and/or connector block.
1. Insert the wires into the correct terminal on the included captive screw connector, as shown
below.
2. Tighten the screws to secure the wires. Do not use high-torque devices as this may
damage the screws and/or connector block.
3. Connect the captive screw connector to the DC 48V power receptacle on the AT-HDVS-200-
TX-PSK.
Power
NOTE: The DC 48V port is only available on the AT-HDVS-200-TX-PSK.
RS-232
The AT-HDVS-200-TX / AT-HDVS-200-TX-PSK provides RS-232 control between an automation
system and an RS-232 device. This step is optional and is used when connecting a computer
that is running the control software.
1. Use wire strippers to remove a portion of the cable jacket.
2. Remove at least 3/16” (5 mm) from the insulation of the RX, TX, and GND wires.
3. Insert the TX, RX, and GND wires into correct terminal on the included captive screw block.
If using non-tinned stranded wire, press the orange tab, above the terminal, while inserting
the exposed wire. Repeat this step for the TX, RX, and GND connections.
GND
RX
TX
RX TX GND

4
Installation Guide
AT-HDVS-200-TX / AT-HDVS-200-TX-PSK
The AT-HDVS-200-TX / AT-HDVS-200-TX-PSK includes four mounting brackets and eight
mounting screws, which provides the option of mounting each unit to any at surface.
The mounting procedure is the same for both the transmitter and receiver.
1. Position one of the mounting brackets, as shown below, aligning the holes on the side of the
enclosure with one set of holes on the mounting bracket.
2. Use the enclosure screws to secure the mounting bracket to the enclosure.
3. Repeat the above steps to attach the second mounting bracket to the opposite side of the
unit.
PW
HDMI
INPUT
DISPLAY
v
v
AT-HDVS-200-TX
VOL
HDMI IN 1 VGA IN AUDIO IN
1
2
VGA
4. Mount the unit using the oval-shaped holes, on each mounting bracket. If using a drywall
surface, a #6 drywall screw is recommended.
NOTE: Mounting brackets can also be inverted to mount the unit under a table
or other at surface.
PW
HDMI
INPUT
DISPLAY
v
v
AT-HDVS-200-TX
VOL
HDMI IN 1 VGA IN AUDIO IN
1
2
VGA
Mounting Instructions
Included screws

5
Installation Guide
AT-HDVS-200-TX / AT-HDVS-200-TX-PSK
1. Connect an HDMI cable between the HD source and the HDMI IN 1 port on the switcher.
2. Connect another HDMI cable between another HD source and the HDMI IN 2 port on the
switcher.
3. Connect a VGA cable from a VGA source to the VGA IN port on the switcher.
4. Connect a 3.5 mm mini-stereo cable from the AUDIO IN port on the switcher to the analog
audio source. The AT-HDVS-200-TX / AT-HDVS-200-TSK-PSK can pass audio either with or
without a video signal. Refer to the User Manual for more information.
5. Connect an category cable, up to 330 feet (100 meters), from the LAN port on the switcher
to a Local Area Network (LAN). Refer to the User Manual for more information.
6. Connect a category cable, up to 230 feet (70 meters), from the HDBaseT OUT port on the
switcher to a PoE-compatible transmitter (not included). Category cables should use EIA/
TIA-568B termination.
7. OPTIONAL: Connect an RS-232 control device to the RS-232 port on the switcher. This
port is used to control functions of the AT-HDVS-200-TX / AT-HDVS-200-TX-PSK, such as
volume up/down, display on/o, etc.
No power supply is required for the AT-HDVS-200-TX / AT-HDVS-200-TX-PSK. The unit will
be powered over the category cable, from an HDBaseT receiver.
Refer to the tables below for recommended cabling when using Altona products with HDBaseT.
The green bars indicate the signal quality when using each type of cable. Higher-quality signals
are represented by more bars.
Core Shielding CAT5e CAT6 CAT6a CAT7
Solid UTP (unshielded) N/A
STP (shielded)
IMPORTANT: Stranded or patch cables are not recommended due to
performance issues.
Installation
Cable Recommendation Guidelines
HDMI IN 2
RS-232
RX
RL
TX
PW
HDMI
INPUT
DISPLAY
v
v
AT-HDVS-200-TX
VOL
HDMI IN 1 VGA IN AUDIO IN
1
2
VGA
FW RS-232
HDMI IN 2 LAN HDBaseT OUT
RS-232
RX
TX
HDMI IN 2
RS-232
RX
RL
TX
PW
HDMI
INPUT
DISPLAY
v
v
AT-HDVS-200-TX
VOL
HDMI IN 1 VGA IN AUDIO IN
1
2
VGA
FW RS-232
HDMI IN 2
DC 48V LAN HDBaseT OUT
RS-232
RX
TX
+
1 2
3
4
5
7
6

6
Installation Guide
AT-HDVS-200-TX / AT-HDVS-200-TX-PSK
Notes

7
Installation Guide
AT-HDVS-200-TX / AT-HDVS-200-TX-PSK
Notes

8
Installation Guide
AT-HDVS-200-TX / AT-HDVS-200-TX-PSK
Version 1 25346-R1
© 2022 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
English Declaration of Conformity
English Declaration of Conformity
Warranty
Chinese Declaration of Conformity 中国RoHS合格声明
The English version can be found under the resources tab at:
https://atlona.com/product/at-hdvs-200-tx/.
The English version can be found under the resources tab at:
https://atlona.com/product/at-hdvs-200-tx-psk/.
To view the product warranty, use the following link or QR code:
https://atlona.com/warranty/.
由SKU列出於:
https://atlona.com/about-us/china-rohs/.
The terms HDMI, HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI licensing Administrator, Inc.
US International
atlona.com •408.962.0515 •41.43.508.4321