TLV MBS33M User manual

172-65272M-04 (MBS33M) 12 October 2021
Pressure Transmitter
MBS33M
Installation
Installation, inspection, maintenance, repairs, disassembly, adjustment and valve opening/closing should
be carried out only by trained maintenance personnel.
1. The joint and the siphon tube are temporarily connected when shipped. Make sure to retighten when
installing the product before use.
Make sure to retighten the joint and siphon tube. If retightening is not carried out, steam
or hot fluid may leak, resulting in malfunction of the product and leading to burns or other
injury.
CAUTION
2. Make sure to use the siphon tube if the operating fluid temperature is 85 C or more.
3. Make sure to use the joint, as the siphon tube cannot be installed without it.
4. Do not put any stress on the diaphragm inside the pressure receiving part.
5. Supply voltage of DC10 to 30V is required for operation. When the product is used with instruments that
do not have a built-in sensor power supply (controller, recorder, indicator, etc.), provide the power
supply for the sensor separately.
6. Ensure that the wiring is carried out with the correct polarity by referring to figures below.
7. Ensure that all the screws for the cover and the wiring connection are firmly tightened once the
installation and the wiring are complete.
Figure 1 Electrical Wiring
(Connected to controllers, indicators, recorders, etc.)
Outline Drawing
Unit: mm
Signal DC 4-20 mA
Power
Supply
24V DC
Pressure
Transmitter
Controller
Recorder
Indicator
71
38
33 (57)*
104 (128)*
33
23
20
518
18
3
∅33 Distance
Across
Flats: 27 mm
G(PF)3/8
1/2
∅6
∅5
Distance
Across
Flats: 27 mm
( )*: Model without data matrix 2D barcode
G(PF)
∅10.5
R(PT)3/8
Distance
Across
Flats: 19 mm
1812
110 215 343 (367)* 104 (128)*
71
38
33
(57)*
Distance
Across
Flats: 27 mm
G(PF)3/8
Distance
Across
Flats: 22 mm
18 18
20
33
G(PF) 1/2
13

172-65272M-04 (MBS33M) 12 Oct 2021
Specifications
Install properly and DO NOT use this product outside the recommended operating
pressure, temperature and other specification ranges. Improper use may result in such
hazards as damage to the product or malfunctions which may lead to serious accidents.
Local regulations may restrict the use of this product to below the conditions quoted.
CAUTION
Model code, measuring range, operating pressure etc. are listed on the label affixed at the side of the product.
(Gauge pressure type is listed as “Pe”and absolute pressure type is listed as “Pa”in the RANGE column
on the label.)
1. Body Specifications
Abs. Pressure Type
Gauge Pressure Type
Model Code
060G1233
060G2160
060G3126
060G2159
060G3128
Pressure Range
0 to 400kPa abs
(0 to 4 bar abs)
0 to 500 kPaG
(0 to 5 barg)
0 to 1000 kPaG
(0 to 10 barg)
0 to 2000 kPaG
(0 to 20 barg)
0 to 2500 kPaG
(0 to 25 barg)
Max.AllowablePress.
800 kPaG
800 kPaG
2000 kPaG
5000 kPaG
5000 kPaG
Applicable Fluids
Gases, Liquids
Weight
Approx. 400 g
Accuracy
0.3 % F.S. (Typical)
Temp. Characteristics
0.02 % F.S./ C
Power Source
D.C. 10 to 30 V
Output Signal
D.C. 4 to 20 mA (2-wire)
Load Resistance
250 to 1000 (varies depending on power source voltage)
Pipe Connection
Screw: G(PF) 3/8
(With a joint attached)
Wiring Connection
Plugconstruction:DIN43650 (PG13.5)
Applicablewirediameter: ø5 to 14 mm
Wetted Part Material
AISI 316/W.No.1.4401
Body Material
AISI 316L/W.No.1.4404
Joint Material
Brass
Pressure Sensing
Construction
Semiconductor strain gauge
Operating Fluid
Temperature Range
-40 to 85 C
(Siphon tube must be used above
85 C)
Transport/Storage
Temperature Range
-50 to 85 C
Protection Class
Rain-proof (IP65)
Vibration Stability
20 G (20 Hz to 2 kHz)
Marine Approvals
LR, DNV, GL, RINA, ABS, BV, NKK, PRS, MRS, KRS
2. Attached Siphon Tube
Connection
Sensor side:
G(PF) 3/8
Pipe side:
R(PT) 3/8
(Body) Material
(JIS) STPG370 (Ni plated)
Max. Operating Press.
20 MPaG
Max. Operating Temp.
350 C
Range Setting
When a pressure unit other than kPa is used with instruments such as controllers, etc., refer to the table
below to set the pressure range on the instrument side.
Unit
Product Range
kg/cm2G
kg/cm2abs
barg
bar abs
psig
psi abs
mmHg G
mmHg abs
0 to 400kPa abs
-1.033 to 3.047
0 to 4.08
-1.013 to 2.987
0 to 4
-14.70 to 43.32
0 to 58.02
-760 to 2240
0 to 3000
0 to 500 kPaG
0 to 5.10
──
0 to 5.00
──
0 to 72.5
──
0 to 3751
──
0 to 1000 kPaG
0 to 10.20
──
0 to 10.00
──
0 to 145.0
──
0 to 7501
──
0 to 2000 kPaG
0 to 20.40
──
0 to 20.00
──
0 to 290.1
──
0 to 15002
──
0 to 2500 kPaG
0 to 25.50
──
0 to 25.00
──
0 to 362.6
──
0 to 18753
──
881 Nagasuna, Noguchi
Kakogawa, Hyogo 675-8511, JAPAN
Tel: [phone]
Load resistance (

)=Power source voltage (V) –10
0.02 (A)
Equation:

172-65272M-04 (MBS33M) 12 Oct 2021
TLV EXPRESS LIMITED WARRANTY
Subject to the limitations set forth below, TLV CO., LTD., a Japanese corporation (“TLV”), warrants that
products which are sold by it, TLV International Inc. (“TII”) or one of its group companies excluding TLV
Corporation (a corporation of the United States of America), (hereinafter the “Products”) are designed and
manufactured by TLV, conform to the specifications published by TLV for the corresponding part numbers
(the “Specifications”) and are free from defective workmanship and materials. The party from whom the
Products were purchased shall be known hereinafter as the “Seller”. With regard to products or
components manufactured by unrelated third parties (the “Components”), TLV provides no warranty other
than the warranty from the third party manufacturer(s), if any.
Exceptions to Warranty
This warranty does not cover defects or failures caused by:
1. improper shipping, installation, use, handling, etc., by persons other than TLV, TII or TLV group
company personnel, or service representatives authorized by TLV; or
2. dirt, scale or rust, etc.; or
3. improper disassembly and reassembly, or inadequate inspection and maintenance by persons
other than TLV or TLV group company personnel, or service representatives authorized by TLV;
or
4. disasters or forces of nature or Acts of God; or
5. abuse, abnormal use, accidents or any other cause beyond the control of TLV, TII or TLV group
companies; or
6. improper storage, maintenance or repair; or
7. operation of the Products not in accordance with instructions issued with the Products or with
accepted industry practices; or
8. use for a purpose or in a manner for which the Products were not intended; or
9. use of the Products in a manner inconsistent with the Specifications; or
10. use of the Products with Hazardous Fluids (fluids other than steam, air, water, nitrogen, carbon
dioxide and inert gases (helium, neon, argon, krypton, xenon and radon)); or
11. failure to follow the instructions contained in the TLV Instruction Manual for the Product.
Duration of Warranty
This warranty is effective for a period of one (1) year after delivery of Products to the first end user.
Notwithstanding the foregoing, asserting a claim under this warranty must be brought within three (3)
years after the date of delivery to the initial buyer if not sold initially to the first end user.
ANY IMPLIED WARRANTIES NOT NEGATED HEREBY WHICH MAY ARISE BY OPERATION OF
LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE AND ANY EXPRESS WARRANTIES NOT NEGATED HEREBY, ARE
GIVEN SOLELY TO THE INITIAL BUYER AND ARE LIMITED IN DURATION TO ONE (1) YEAR
FROM THE DATE OF SHIPMENT BY THE SELLER.
Exclusive Remedy
THE EXCLUSIVE REMEDY UNDER THISWARRANTY, UNDER ANY EXPRESSWARRANTY OR
UNDER ANY IMPLIED WARRANTIES NOT NEGATED HEREBY (INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE), IS
REPLACEMENT; PROVIDED: (a) THE CLAIMED DEFECT IS REPORTED TO THE SELLER IN
WRITING WITHIN THE WARRANTY PERIOD, INCLUDING A DETAILED WRITTEN DESCRIPTION
OF THE CLAIMED DEFECT AND HOW AND WHEN THE CLAIMED DEFECTIVE PRODUCT WAS
USED; AND (b) THE CLAIMED DEFECTIVE PRODUCT AND A COPY OF THE PURCHASE INVOICE
IS RETURNED TO THE SELLER, FREIGHT AND TRANSPORTATION COSTS PREPAID, UNDER A
RETURN MATERIAL AUTHORIZATION AND TRACKING NUMBER ISSUED BY THE SELLER. ALL
LABOR COSTS, SHIPPING COSTS, AND TRANSPORTATION COSTS ASSOCIATED WITH THE
RETURN OR REPLACEMENT OF THE CLAIMED DEFECTIVE PRODUCT ARE SOLELY THE
RESPONSIBILITY OF BUYER OR THE FIRST END USER. THE SELLER RESERVES THE RIGHT
TO INSPECT ON THE FIRST END USER’S SITE ANY PRODUCTS CLAIMED TO BE DEFECTIVE
BEFORE ISSUING A RETURN MATERIAL AUTHORIZATION. SHOULD SUCH INSPECTION

172-65272M-04 (MBS33M) 12 Oct 2021
REVEAL, IN THE SELLER’S REASONABLE DISCRETION, THAT THE CLAIMED DEFECT IS NOT
COVERED BY THISWARRANTY, THE PARTY ASSERTING THISWARRANTY SHALL PAY THE
SELLER FOR THE TIME AND EXPENSES RELATED TO SUCH ON-SITE INSPECTION.
Exclusion of Consequential and Incidental Damages
IT IS SPECIFICALLY ACKNOWLEDGED THAT THIS WARRANTY, ANY OTHER EXPRESS
WARRANTY NOT NEGATED HEREBY, AND ANY IMPLIED WARRANTY NOT NEGATED HEREBY,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, DO NOT COVER, AND NEITHER TLV, TII NOR ITS TLV GROUP
COMPANIES WILL IN ANY EVENT BE LIABLE FOR, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, INCLUDING, BUT NOT LIMITED TO LOST PROFITS, THE COST OF DISASSEMBLY
AND SHIPMENT OF THE DEFECTIVE PRODUCT, INJURY TO OTHER PROPERTY, DAMAGE TO
BUYER’S OR THE FIRST END USER’S PRODUCT, DAMAGE TO BUYER’S OR THE FIRST END
USER’S PROCESSES, LOSS OF USE, OR OTHER COMMERCIAL LOSSES. WHERE, DUE TO
OPERATION OF LAW, CONSEQUENTIAL AND INCIDENTAL DAMAGES UNDER THIS WARRANTY,
UNDER ANY OTHER EXPRESS WARRANTY NOT NEGATED HEREBY OR UNDER ANY IMPLIED
WARRANTY NOT NEGATED HEREBY (INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) CANNOT BE EXCLUDED,
SUCH DAMAGES ARE EXPRESSLY LIMITED IN AMOUNT TO THE PURCHASE PRICE OF THE
DEFECTIVE PRODUCT. THIS EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES,
AND THE PROVISION OF THIS WARRANTY LIMITING REMEDIES HEREUNDER TO
REPLACEMENT, ARE INDEPENDENT PROVISIONS, AND ANY DETERMINATION THAT THE
LIMITATION OF REMEDIES FAILS OF ITS ESSENTIAL PURPOSE OR ANY OTHER
DETERMINATION THAT EITHER OF THE ABOVE REMEDIES IS UNENFORCEABLE, SHALL NOT
BE CONSTRUED TO MAKE THE OTHER PROVISIONS UNENFORCEABLE.
Exclusion of Other Warranties
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND ALL
OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY
DISCLAIMED.
Severability
Any provision of this warranty which is invalid, prohibited or unenforceable in any jurisdiction shall, as
to such jurisdiction, be ineffective to the extent of such invalidity, prohibition or unenforceability without
invalidating the remaining provisions hereof, and any such invalidity, prohibition or unenforceability in
any such jurisdiction shall not invalidate or render unenforceable such provision in any other
jurisdiction.

172-65272M-04 (MBS33M) 12 Oct 2021
Service
For Service or Technical Assistance: Contact your TLV representative or your regional TLV office.
In Europe:
Daimler-Benz-Strahnical Assistance: Contact Germany
Tel:
Fax:
[49]-(0)7263-9150-0
[49]-(0)7263-9150-50
Units 7 & 8, Furlong Business Park, Bishops Cleeve, Gloucestershire GL52
8TW, U.K.
Tel:
Fax:
[44]-(0)1242-227223
[44]-(0)1242-223077
Parc d)1242-223077g Business Park, Bishops Cleeve, GloucestershiPriest,
France
Tel:
Fax:
[33]ced)1242-22307
[33]-(0)4-72482220
In North America:
13901 South Lakes Drive, Charlotte, NC 28273-6790, U.S.A.
Tel:
Fax:
[1]-704-597-9070
[1]-704-583-1610
In Mexico and Latin America:
Av. Jeso and Latin America:arlotte, Hda. de las Palmas, Huixquilucan, Edo.
de México, 52763, Mexico
Tel:
Fax:
[52]-55-5359-7949
[52]-55-5359-7585
In Oceania:
Unit 8, 137-145 Rooks Road, Nunawading, Victoria 3131, Australia
Tel:
Fax:
[61]-(0)3-9873 5610
[61]-(0)3-9873 5010
In East Asia:
36 Kaki Bukit Place, #02-01/02, Singapore 416214
Tel:
Fax:
[65]-6747 4600
[65]-6742 0345
Room 5406, No. 103 Cao Bao Road, Shanghai, China 200233
Tel:
Fax:
[86]-(0)21-6482-8622
[86]-(0)21-6482-8623
No.16, Jalan MJ14, Taman Industri Meranti Jaya, 47120 Puchong,
Selangor, Malaysia
Tel:
Fax:
[60]-3-8065-2928
[60]-3-8065-2923
252/94 (K-L) 17th Floor, Muang Thai-Phatra Complex Tower B,
Rachadaphisek Road, Huaykwang, Bangkok 10310, Thailand
Tel:
Fax:
[66]-2-693-3799
[66]-2-693-3979
#302-1 Bundang Technopark B, 723 Pangyo-ro, Bundang, Seongnam,
Gyeonggi, 13511, Korea
Tel:
Fax:
[82]-(0)31-726-2105
[82]-(0)31-726-2195
In the Middle East:
Building2W, No. M002, POBox 371684, Dubai Airport Free Zone, Dubai, UAE
Email:
[email protected]
In Other Countries:
881 Nagasuna, Noguchi, Kakogawa, Hyogo 675-8511, Japan
Tel:
Fax:
[81]-(0)79-427-1818
[81]-(0)79-425-1167
Manufacturer
Danfoss A/S