Shindaiwa DGK14F User manual

OWNER’S AND OPERATOR’S MANUAL
Vertical, Water-Cooled 4-Cycle Diesel Engine
DGK14F
X753-007 45 0
X753801-230 0
CAUTION
Do not operate the Generator, or any other appliance, before you have read and
understood the instructions for use and keep near for ready use.
California Proposition 65
WARNING
Breathing diesel engine exhaust exposes you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
Always start and operate the engine in a well ventilated area.
If in an enclosed area, vent the exhaust to the outside.
Do not modify or tamper with the exhaust system.
Do not idle the engine except as necessary.
For more information go to www.P65warnings.ca.gov/diesel.
WARNING
Cancer and reproductive Harm-
www.P65Warnings.ca.gov
WARNING
Batteries, battery posts, terminals and related accessories contain lead and lead
compounds, and other chemicals known to the State of California to cause cancer
and birth defects or other reproductive harm. WASH HANDSAFTER HANDLING.

Introduction
Thank you for purchasing thisShindaiwa soundproof dieselengine generator.
This manualhasbeen created toensuresafeusage ofthisgenerator. Besureto readthis
manualbeforeoperation. Improper operation/handling of thisgeneratorwill resultin an accident
or malfunction.
Handling/Operationof thisgenerator can onlybeperformedbypersons whounderstand the
contentsof thismanualandcanhandle/operatethegenerator inasafemanner. Personswho
suffer from an illness, are taking medicine or not feeling wellsuch that safeoperationwouldbe
negativelyaffected must notoperate this generator.
Workperformedusingthis generator andhandling/operationof thisgeneratormust be in
accordance with corresponding laws and regulations based on suchlaws. Consult withthe
authorized distributor where this generator was purchased if you have any inquiries regarding the
corresponding laws.
Always be sure to include thismanualwhen loaning out this generator and instruct operating
personnelto readthismanualbefore operation.
Storethis manualin a specified location whereit will be secureandavailable for consulting at any
time. Order another copyfrom the authorized distributorwhere thisgenerator waspurchased if
this manual becomesdusty,grimyor torn.
Consult withtheauthorized distributor wherethisgenerator waspurchased if you haveany
inquiries regarding any pointsrelatedtothis generator andmanual.
When inquiringaboutthis generator,be sure to provide themodel name andserial number.
If disposing of this generator, do so in a manner that is in compliancewith laws related to
industrial waste. Contact the authorized distributor wherethegenerator waspurchased if you
have anyinquiriesregardingproper disposal.
Cautionnoticeranksin thismanualare classifiedas follows.
WARNING: Indicates a potentially hazardous situation which, if not
avoided, can result in death or serious injury.
CAUTION : Indicates a potentially hazardous situation which, if not avoided,
canresult inminoror moderateinjuryandpropertydamage.
< Note> : Othertypes of cautions and indications.
Note that CAUTION items can also lead to major accidents under somecircumstancesif
notcorrectly followed.
All caution notices areimportant. Be sureto followallof them.

1
Table of Contents
1. Safety Instructions ..........................................................................2
2. Specifications ..................................................................................6
2-1. Specifications............................................................................6
2-2. Ambient Conditions...................................................................7
3. Applications..................................................................................... 7
4. Part Names.......................................................................................7
4-1. External View/Part Names ........................................................7
4-2. Operation Panel Configuration..................................................9
5. Equipment...................................................................................... 10
5-1. Available Output Monitor.........................................................10
5-2. Spill Containment ....................................................................10
5-3. Warning Indicators .................................................................. 11
5-4. Spill Containment Overflow Warning Indicator ........................ 13
5-5. Meters and Gauges.................................................................13
5-6. Fuel Piping Switch (3Way Fuel Valve)..................................... 16
6. Transport/Installtion ...................................................................... 16
6-1. Transport Procedures.............................................................. 16
6-2. Installation Procedures............................................................ 17
7. Load Connections ......................................................................... 18
7-1. Load Cable Selection.............................................................. 18
7-2. Connecting Load Cables......................................................... 19
8. Pre-Operation Inspection.............................................................. 20
8-1. Checking Engine Oil................................................................ 20
8-2. Checking Coolant....................................................................21
8-3. Checking the Fuel ................................................................... 22
8-4. Checking the Spill Containment ..............................................22
8-5. Checking for Fuel, Oil and Coolant Leaks...............................23
8-6. Checking the Battery...............................................................23
9. Oprating Procedures..................................................................... 24
9-1. Initial Startup/Pre-Check.......................................................... 24
9-2. Procedures during Operation .................................................. 26
9-3. Stopping Operation ................................................................. 27
9-4. Protective Functions................................................................27
9-5. Connecting with External Fuel Tank........................................29
10. Inpection/Maintenance.................................................................. 30
11. Long-Term Storage........................................................................ 39
12. Troubleshooting............................................................................. 41
13. Generator Circuit Diagram............................................................ 44
14. Engine Electrical Circuit Diagram................................................ 45

2
1. Safety Instructions
WARNING : EXHAUST GAS POISONING
Do not operatethegeneratorinpoorly ventilated areas suchas indoorsortunnels,astheexhaust
gasof the enginecontainssubstancesthat areharmfultohumanhealth.
Do not direct exhaustfumes at bystanders or buildings.
WARNING : ELECTRIC SHOCK
Do not operate the equipment with any doors or covers open.
AlwaysturnallthebreakersOFF, placethestarter switchin the STOPpositionandstop the
enginebefore connecting/disconnectingtheloadcable tothe output terminalor receptacle.
Closethe receptaclecoverbeforeoperating.
Do not insert a pin, wire or other metalobject intothe electrical outlet.
Donottouch thegeneratorifthegeneratoror casingoryour body becomes wetduring operation.
Do nottouchinternalelectric partswhilethegeneratoris operating.
Always turn the starter switch to theSTOPposition and stop the engine, then close and lock
OPERATIONPANELDOOR before checking or maintaining the engine or anyequipment.
WARNING : INJURY
Closeall doors andlock them during operation.
Do notopen the checkdoor whenthe starterswitch is intheAUTO or STARTposition.It will
causeinjuryby rotating partssuchas coolingfans andfanbelt.
Always turn the starter switch to theSTOPposition and stop the engine, then close and lock
OPERATIONPANELDOOR before checking or maintaining the engine or anyequipment.
Usethe lifting hook to lift the machines, and do notlift up by using tie downs. Use of such could
result in thegenerator falling.
Do not liftany additional weight such as fuel tanksor trailers.
No persons shouldever be undera liftedgenerator.
Always be sure to check thatthe breakers on load side andswitches for any equipment using the
generatorareat OFF beforeturningthebreakertoON.Alsobesuretoadvise personnelon the
load side that power will be turnedon or off beforeoperating the breaker.
Do notmodifytheequipmentanddo not operatewith partsremoved.
CAUTION : EYE/SKIN INJURY
Wear rubber gloves and other protective wear to protecteyes, skin and clothing fromthe battery
fluid which contains diluted sulfuric acid. If thebatteryfluid contactseyesorskin,washout
immediately witha sufficient amountof clean water. Besure toreceive medicaltreatment,
especiallyif thefluid contactstheeyes.

3
CAUTION : EXPLOSION
Never use or rechargethe battery if the fluid level is below theminimum level.
Do not createsparks or bring flamenear thebattery as it generatesflammablegas.
CAUTION : FIRE
Do not carryflammable items(suchas fuel,gas andpaint) or itemsthat arehighlycombustible
nearthe generator as themuffler, exhaustgas andotherpartsbecome extremely hot.
Position this generator 3 ft. (1 m) or morefrom wallsor other hindrances,andon a level surface.
Do not connect thegenerator output to indoor wiring.
This generator usesdieselfuel.Always be suretostopthe engineandnotbring flamesclose
when inspecting fuelor refueling. Wait until the engine has cooledbeforeperformingsuch
procedures.
If fuelspills,always besuretoopen the spillcontainmentdrain valveanddrain offthespilledfuel.
Do not operatethe equipment withliquid accumulated in the spillcontainment.
If fuelor oilleaks, repairtheleaking locationbeforeoperating.
Always be sure to wipe upany spilled fuel or oil.
Allowthe generator to coolbefore covering with the protectivecover.
Never allowflametocomeclose tothegenerator.
Always make sure that the engine is stoppedwhen working on piping.
After working onthe piping,check thatthereisnofuelleakage.
Absolutely never inspect orperform maintenance totheequipment nearfireor other openflame.
CAUTION : ELECTRIC SHOCK
Do not sprinkle water on the equipment and do not use where exposed to rain.
CAUTION : BURNS
Do nottouch the engine andsurrounding componentsimmediately after stopping theengineas
they arestillextremelyhot.
Do not openthe radiator cap immediatelyafter stopping the engine. Doingso will result in hot
steam gushing out.
Hotsteam gushes out from the coolant sub-tank if thegenerator overheats. Donot touchthe
coolant sub-tank.
Always be sure to stop the engine and allowthe engine to cool when performing inspection or
maintenanceof engineoil. Opening the oil levelgaugeor oil filler cap during operation will result in
hot oilgushing out.

4
CAUTION : INJURY
Always besuretouselifting hooks when lifting upthegenerator, andslowly lift it straight up.
Personnelperforming lifting work must wear protective gearssuch as helmets, safetyshoes and
gloves.
Remove the woodties if using anchors to secure thegenerator.
Position thegenerator on a level stable surface so that it cannot slide or move in any manner.
Before starting operation, always be suretoturnoff allswitches of equipment using the generator
andall breakerstoOFF.
Do not move the generatorduring operation.
Do not operatethegeneratorifit has beenmodified or anypartshavebeen removed.
Securely fixthe equipmentwith ropeor similar item sothatit cannot move when transporting by
truck or other vehicle.
CAUTION : PROPERTY DAMAGE
Do not usethe equipment for anyimproper applications.Improper usagecanresult inan accident
or malfunction.
If using this generator for medical equipment, check beforeuse withthe medical equipment
manufacturer,doctor, hospitalorsimilar entity.
Check that the generator output setting, receptacle connection and loadpower source are
consistent.
Cableburnout can occur duetogenerated heat if the load current exceeds the allowablecurrent
of the cable.
Thevoltage drop betweencables is large if thecable is excessivelylong or thin, resulting in
decreased input voltagetoequipment using the generator, thereby causing decreased
performance, faultyoperationand malfunction.

5
Warning /Caution Label Locations
If warning or caution labels become damaged and difficult to read, replace with new labels in
the indicated locations. Order labels using part number indicated in the parenthesis.
①
Caution: GM SPEC LLC
Part no. : X505-007840
②
Warnig: Fire
Part no. : X505-007650
③
Caution: Burn
Part no. : X505-007830
④
Warnig: caution
Part no. : X505-010910
⑤
Warnig: Injury
Part no. : X505-007550
⑥
Bonnet grounding terminal
Part no. : M704-001400
⑦
Spill containment bolt
Part no. : M707-000380
⑧
EPA regulation complied notice
Part no. : X505-008400
⑨
Caution
Part no. : X505-010800
⑩
Warning: Proposition 65 Gen
Part no. : X505-010400
⑪
Warning: Proposition 65 Battery
Part no. : X505-010410
⑫
Warning: Injury
Part no. : X505-010920
①
⑤
③
③
⑫
⑦
⑨
⑦
②
④
⑥
⑪
⑩
⑧
⑫
Battery

6
2. Specifications
2-1. Specifications
Model
Unit
DGK14F
Alternator
Generator Type
-
Revolving Field Brushless
Armature Connection
-
ZigZag-W
Rated Frequency
Hz
60
Rated Output(Prime)
kVA
14
kW
14
Standby Output
kVA
14.7
kW
14.7
Rated Voltage
V
240/120
Rated Current
A
58.3
Phase
Single phase
Power Factor
-
1.0
Insulation class
-
F
Excitation
-
Self Excitation (brushless)
No. of Poles
-
4
Engine
Type
-
Vertical Water-Cooled 4-Cycle Diesel
Model(Manufacturer)
-
Kubota D1503
No. of Cylinders
(bore × stroke)
(in./mm)
3(3.27×3.64/83×92.4)
Continuous Rated
Output
hp
19.5
Rated Speed
rpm
1800
Displacement
cu.in./liters
91.5/1.499
Combustion System
-
Indirect Injection
Cooling Method
-
Radiator
Lubricating Method
-
Forced Lubrication
Starting Method
-
Electric
Fuel
-
No.2-D,S15 EPA regulation
Lubricating Oil
-
CF class
Fuel Tank Capacity
gal./liters
34.3/130
Lubricant Volume
gal./liters
1.9/7.3 (including filter 0.1/0.3)
Cooling Water Volume
gal./liters
2.3/8.8 (including sub-tank 0.3/1.1)
Starting Motor Capacity
V-kW
12-1.4
Charging Alternator
Capacity
V-A
12-30
Battery Capacity
V-Ah
12-55
Unit
Length
in./mm
55/1390
Width
in./mm
28/704
Height
in./mm
47/1204
Dry Weight
lbs./kg
1378/625
Net Weight
lbs./kg
1669/757

7
Lifting Hook
Tie-Down
Tie-Down
Operation Panel Door
Terminal Cover
Fuel Inlet Cover
Radiator Plate
Fuel Drain Plug
2-2. Ambient Conditions
Use this generator in ambient conditions as described below. Failure to provide these
conditions can result in problems such as malfunction, insufficient output and reduced
durability.
■Ambient temperature: 5 to 104 °F (-15 to 40 °C)
■Relative humidity: 85% or less
■Altitude: 984 ft. (300 m) or less
3. Applications
Power source for submerged pumps and similar civil engineering equipment
Power source for lighting and similar equipment
Power source for electrical tools and household appliances
4. Part Names
4-1. External View/Part Names
CAUTION : PROPERTY/SECONDARY DAMAGE
Do not use for any application other than those listed above.
If using this generator for medical equipment, check before use with the
medical equipment manufacturer, doctor, hospital or similar entity.
Spill Containment Drain Plug
Spill Containment Drain Valve

8
Oil Filter
Oil Level Gauge
Water Separator
Fuel Filter
Battery
Fuel Tank
（Inside）
Alternator Check Door
Air Cleaner
Coolant Sub-Tank
Engine Check Door
External Fuel Inlet
External Fuel Return
Oil Drain Plug
Coolant Drain Plug
3way Fuel Valve
Radiator
* Shown with side-plate removed.
Accessories
Owner’s
and
Operator’s
Manual
Engine
Warranty
Manual
Fan Guard
Oil Filler

9
4-2. Operation Panel Configuration

Main Circuit Breaker
○
11
Hour Meter

Voltmeter
○
12
Warning Indicators

Pilot Lamp
○
13
Engine Monitor

Glow Lamp
○
14
Fuel Meter

Throttle Switch
○
15
Oil Pressure/ Water Temperature
/ Speed Selector Switch

Voltage Regulator
○
16
Display Selector Switch

Starter Switch
○
17
Available Output Monitor

Accessory Switch

Over Crank /
No Speed Signal Indicator

Spill containment Overflow
Warning Indicator
⑩
⑧
⑮
⑨
⑫
②
⑤
③
④
①
⑭
⑪
⑬
⑥
⑯
⑦
⑰

10
5. Equipment
5-1. Available Output Monitor
The available generated output for each output power source is displayed digitally. You can
use the display selector switch to change the display in the following order: Total output of
240V Receptacle and 240/120V Receptacle, 120V Receptacles output. Total output of 240V
Receptacle and 240/120V Receptacle is always displayed when the engine is started.
< Note >
Consider thedigitally displayed availableoutput as an
approximateestimate. Be suretothoroughlyconsider the
displayed value andthe usedload capacity when using a load
such as a motor withlargestarting capacity.
If “--”is displayed forthe availableoutput, it meansthat usage
hasexceededthe ratedcapacity. Immediatelystop the
equipment being used and reduce theload capacityof the
equipment.
5-2. Spill Containment
The bed of this generator is equipped with a spill containment (structure for preventing
leakage of liquids) so that any spilled liquid will not leak to outside of the generator when oil or
fuel is spilled or leaks. Before starting operation, check if there is accumulated liquid in the
spill containment. Flush out any liquid that has accumulated.
(Refer to section “8-4. Checking the Spill Containment” for inspection procedures. )
(Refer to section “10. Inspection/Maintenance (9) Flushing Liquid in Spill Containment”
for flushing procedures. )
The generator is equipped with the following in order to prevent liquid from spilling in case you
forget to flush the liquid: The operation panel is equipped with an indicator that illuminates
when its sensor is triggered as the spill containment capacity accumulated enough liquid to
reach to about 4.5gal(17 liters).
If the liquid stored in the spill containment exceeds approximately about 13.4gal(51 liters)
during operation, the SPILL CONTAINMENT overflow warning indicator illuminates, and the
engine will be automatically stopped. If this occurs, flush the liquid stored in the spill
containment.
(Refer to section “10. Inspection/Maintenance (9) Flushing Liquid in Spill Containment”.)
WARNING : INJURY
Do not open the check door when the starter switch is in the AUTO or START
position. It will cause injury by rotating parts such as cooling fans and fan belt.
Always turn the starter switch to the STOP position and stop the engine,
then close and lock OPERATION PANEL DOOR before checking or
maintaining the engine or any equipment.
CAUTION : BURNS
Do not touch the engine and surrounding components immediately after
stopping the engine as they are still extremely hot.
CAUTION : FIRE
If fuel or oil leaks , repair the leaking location before operating.
Display Selector
Switch

11
< Note >
Water canalso accumulatein the spillcontainment due torain entering intothegenerator.
Accordingly, you shouldperiodically flush liquid accumulated within thegenerator. However, you
should flush water according tothe frequency/amount of rainfall.
Thetypes of liquids that can accumulate in the spillcontainment include oil, fuel, coolant and
batteryfluid such that it isnot possibleto distinguishbetween rainwaterandother liquids. Dispose
of flushed liquids accordingto the applicablelawsandregulations.
5-3. Warning Indicators
This generator is equipped with the following warning indicators: BATTERY (insufficient
charging), OIL PRESS (engine oil pressure), WATER TEMP (coolant temperature), OVER
SPEED (engine overspeed), AIR FILTER (air cleaner clogging), SPILL CONTAINMENT (spill
containment amount). Selecting the starter switch from STOP to START position causes the
BATTERY and OIL PRESS warning indicator to illuminate, and all indicator lights will go off as
engine starts. An indicator illuminates if malfunction/fault occurs during operation and the
engine automatically stops depending on the fault type (except for SPILLCONTAINMENT).
If the generator automatically stops, set the starter switch to STOP and restart the engine.
Check each illuminated warning indicator at the time of automatic stop, and inspect the failed
component.
(1) BATTERY (Insufficient Charging) Warning Indicator (Low Battery Voltage)
The BATTERY warning indicator illuminates and the engine automatically stops when
charging is not possible during operation. If this occurs, contact authorized distributor where
the generator was purchased.
< Note >
This batterycharging warning indicator cannot detect batterydeterioration or insufficient battery
fluid. (Refer to section “8-6. Checking the Battery”.)
WARNING : INJURY
Do not open the check door when the starter switch is in the AUTO or START
position. It will cause injury by rotating parts such as cooling fans and fan belt.
Always turn the starter switch to the STOP position and stop the engine,
then close and lock OPERATION PANEL DOOR before checking or
maintaining the engine or any equipment.
CAUTION : BURNS
Do not touch the engine and surrounding components immediately after
stopping the engine as they are still extremely hot.

12
(2) OIL PRESS (engine oil pressure) Warning Indicator (Low Oil Press.)
CAUTION: BURNS
Always be sure to stop the engine and allow the engine to cool when
performing inspection or maintenance of engine oil. Opening the oil level
gauge or oil filler cap during operation will result in hot oil gushing out.
If the engine oil pressure drops below 7 psi (0.49 x 100 kPa) during operation, the OIL
PRESS warning indicators illuminates, and the engine will be automatically stopped.If this
occurs, check the engine oil level and add engine oil until it reaches the maximum level.
< Note >
This oil pressurewarning indicator cannot detect oildeterioration. Changethe engineoil
periodically. (Refer to section “8-1. Checking Engine Oil”.)
(3) WATER TEMP (Coolant Temperature) Warning Indicator (High Water Temp.)
CAUTION: BURNS
Do not open the radiator cap immediately after stopping the engine.
Do so will result in hot steam gushing out.
Hot steam gushes out from the coolant sub-tank if the generator overheats.
Do not touch the coolant sub-tank.
If the coolant temperature rises above 239 °F(115℃) during operation, the WATER TEMP
warning indicators illuminate, and the engine will be automatically stopped. If this occurs, hot
steam will gush out of the coolant sub-tank. Check the coolant sub-tank coolant level after
the generator cools and add coolant to the coolant sub-tank if it is insufficient. (Refer to
section “8-2. Checking Coolant”.) If the coolant is at the specified amount, it is probable
that the fan belt is loose or there is a coolant leak. Wait for the engine to cool down and
inspect for these problems.
< Note >
Thecoolanttemperaturecannotbe detected if the coolant level isexcessivelylow.Alwaysbe
sure to check the coolant level in theradiator coolant sub-tank beforestarting operation.
(4) OVER SPEED (Engine Overspeed) Warning Indicator
This generator is equipped with a function such that the engine is automatically stopped if an
engine fault occurs causing the engine speed to increase excessively. If the engine speed
rose above 2070rpm during operation, the OVER SPEED warning indicators illuminates, and
the engine will be automatically stopped. If this occurs, it is probable that some malfunction
has occurred in the engine. Contact authorized distributor where the generator was
purchased.
(5) AIR FILTER (Air Cleaner Clogging) Warning Indicator
The AIR FILTER warning indicator illuminates if the air cleaner element becomes clogged
during operation. If it illuminates, immediately stop the engine and clean or replace the air
cleaner element.(Refer to section “10. Inspection/Maintenance (3) Air Filter Element
Cleaning/Replacement”.)

13
(6) SPILL CONTAINMENT (Spill Containment Amount) Checking Indicator
The SPILL CONTAINMENT checking indicator illuminates if the liquid stored in the spill
containment exceeds approximately about4.5gal(17 liters) during operation. If it illuminates,
immediately stop the engine and flush the liquid stored in the spill containment.
(Refer to section “10. Inspection/Maintenance (9) Flushing Liquid in Spill Containment”.)
< Note >
Theengine may not be stoppedonly if the spill containment checking indicator illuminates during
operation.
Whenthe spill containmentchecking indicator illuminates during operation,stop theengine,
check for fuel, oil andcoolantleakage, andrepair as necessary.
Do not use the equipment with liquidaccumulatedinthe spill containment. Drain the spill
containment before using.
5-4. Spill Containment (Spill Containment Amount) Overflow Warning Indicator
If the liquid stored in the spill containment exceeds approximately about 13.5gal(51 liters)
during operation, the SPILL CONTAINMENT overflow warning indicator illuminates, and the
engine automatically stops. If this occurs, flush the liquid stored in the spill containment.
(Refer to section “10. Inspection/Maintenance (9) Flushing Liquid in Spill Containment”.)
< Note >
Although the fluids that canleak internallyconsistof oil, fuel andcoolant, thespill containment
does not have a functionthatcan separaterainwaterthat has leakedinto theequipment from
theseinternally leaked fluids.Properlydisposeof liquiddrainedfrom thespillcontainment ina
manner accordingto the applicablelaws andregulations.
5-5. Meters and Gauges
Engine Meters and Gauges
(1) Hour Meter
Displays the operating time. Use this as a reference for managing periodic inspection
interval.
(2) Engine Monitor
Displays the engine speed, coolant temperature and oil pressure. Switching the selector
switch changes the display in the following order: Speed Water temp Oil press. Engine
speed is displayed first when the engine is started.
WARNING : INJURY
Do not open the check door when the starter switch is in the AUTO or START
position. It will cause injury by rotating parts such as cooling fans and fan belt.
Always turn the starter switch to the STOP position and stop the engine,
then close and lock OPERATION PANEL DOOR before checking or
maintaining the engine or any equipment.
CAUTION : BURNS
Do not touch the engine and surrounding components immediately after
stopping the engine as they are still extremely hot.
CAUTION : FIRE
If fuel or oil leaks, repair the leaking location before operating.

14
①Speed
Displays the engine speed. 1800rpm is displayed at 60
Hz.
②Water Temp
Displays the temperature of the engine coolant.
Normal temperature displayed during operation
should generally between 158°F (70℃) and 203°F
(95℃) depending on usage.
< Note >
If the coolant temperaturerisesabove212°F (100°C),immediatelystop all connectedequipment
to thegenerator, andidlethe enginewhilecooldownthecoolant temperature.
③Oil Press
Displays the pressure of the engine lubrication system. Normal pressure displayed during
operation should generally 35 and 57 psi (2.4－3.9 x 100 kPa) depending on usage.
However, the pressure may rise above this range just after starting a cold engine. Idle the
engine until it reaches the normal pressure.
(3) Fuel Meter
It shows the amount of fuel in the tank.
All lamps are lit when the amount reaches to the maximum level, and FULL is
lit.decreases .The lit lamp decreases as the amount of fuel in the tank reaches to EMPTY.
The fuel level on the control panel will only display the fuel level for the internal fuel tank.
Generator Meters and Gauges
(1) Voltmeter
The voltmeter displays the single-phase output
voltage(voltage between U-W). Check that
240V at 60Hz is displayed during operation.
Indicators
(1) Glow Lamp
This lamp illuminates when the starter switch is on START
positon. This lamp turns off when pre-heating is completed.
This lamp turns off and the generator starts.
< Note >
Pre-heating completesin approximately5seconds.
(2) Pilot Lamp
This lamp illuminates when the engine is operating to indicate
that power is being generated.
Hour Meter
時間計
Oil Press
Water Temp
Fuel Meter
Speed
Selector
Switch
Pilot Lamp
Glow Lamp
Starter Switch

15
(3) Over Crank / No Speed Signal Indicator
This indicator illuminates if the engine fails to start.
If that happens, set the "STARTER SWITCH" selector to STOP,
and inspect the machine. (Refer to section "12. Troubleshooting.")
If this indicator starts flashing, the rotation signal has not been
detected correctly.Contact the authorized distributor where the
generator was purchased.
Switches
(1) Starter Switch
The engine warms up and starts automatically.
START
The engine is started in this position.
The engine warms up and starts
automatically.
STOP
The engine is stopped, and the power
supply is turned off completely in this
position. You can operate the
ACCESSORY switch in this position.
AUTO
The engine is started in this position when
the REMOTE START terminal closes.
(2) Accessory Switch
If you select ON, the display turns on, and you can check the fuel level.
< Note >
Setthe STARTER SWITCH selector to STOPto activate this function.
Do not leavetheACCESSORYswitch at ON position. This is causing batteryfrom drain out.
(3) Breaker
This switch is for transmitting electrical power to the load side. Turn to ON position to output
voltage to the output receptacles. Output to the load side is cut off when there is a short
circuit or overload on the load side.
< Note >
Do not turns off/on the breaker manually to operate or stop a load.
Voltage Regulator/Engine Speed Switch
(1) Voltage Regulator
This dial is for regulating voltage output by the generator. Turn the
dial clockwise to increase the voltage and counterclockwise to
decrease it.
(2) Throttle Switch
This switch isfor changing the engine speed. Set toIDLING when starting,
warming up and cool down the engine, and set to RUN during ratedoperation.
< Note >
Theengine is running at 1800rpm with 60Hz regardless of throttle switch position if youleave
starter switchinAUTO position.
Main
Breaker
Over Crank /No Speed
Signal Indicator
Remote Start
Terminal
Throttle Switch
Accessory Switch
Starter Switch

16
5-6. Fuel Piping Switch (3Way Fuel Valve)
CAUTION:
Always make sure that the engine is stopped when working on piping.
Always be sure to wipe up any spilled fuel.
After working on the piping, check that there is no fuel leakage.
Change the three-way fuel valve to switch to supply fuel from the external tank. In that case,
the internal fuel tank is not used.
(1) If using the internal fuel tank
Change the lever of the three-way fuel valve turned to the “A” side to supply fuel from the
internal tank. It is turned to the “A” side when the generator is shipped from the factory.
< Note >
When disconnecting piping from the external tank, turn the lever to the “A” side, andattachthe
bundledplug(R1/2”) totheexternal tankfuelinlet/return.
(2) If using an external fuel tank
Connect hoses from the external fuel tank to the external fuel inlet and the external fuel
return. Change the lever of the 3way fuel valve to the “B” side to supply fuel from the
external tank.
Refer to “9-5. Connecting with External Fuel Tank” for corresponding procedures.
6. Transport/Installtion
6-1. Transport Procedures
WARNING : INJURY
Do not lift up the unit using tie down. Use of such could result in the generator falling.
No persons should ever be under a lifted generator.
CAUTION : INJURY
Always be sure to use lifting hooks when lifting up the generator, and raise it
slowly at a completely vertical angle.
Personnel performing lifting work must wear protective gears such as helmets,
safety shoes and gloves.
Do not move the generator during operation.
Position B
Position A
External Fuel
Return
External Fuel
Inlet
3Way Fuel
Valve

17
(1) Lifting Procedures
Always be sure to use lifting hooks when lifting up the generator, and raise it slowly at a
completely vertical angle.
(2) Transport
When transporting this generator, tie rope to the left and right tie downs, and securely fix the
generator.
< Note >
Handle this generator with great care when raising, lowering and transporting. Roughhandling of
generatorcan result in damageor malfunction.
6-2. Installation Procedures
WARNING : EXHAUST GAS POISONING
Do not operate the generator in poorly ventilated areas such as indoors or
tunnels, as the exhaust gas of the engine contains substances that are
harmful to human health.
Do not direct exhaust fumes at bystanders or buildings.
CAUTION : FIRE
Do not carry flammable items (such as fuel, gas and paint) or items that are
highly combustible near the generator as the muffler, exhaust gas and other
parts become extremely hot.
Operate this generator 3 ft. (1 m) or more from walls or other hindrances, and
on a level surface.
Remove the wood ties if using anchors to secure the generator
Do not connect the generator output to indoor wiring.
If installing this generator, set up barriers or fencing completely around the boundary
line of the construction area and take measures to prevent persons not involved in the
construction from entering the area.
Position this generator on a hard, flat and leveled surface.
Position this generator 3 ft. (1 m) or more from walls or other hindrances so that the
operation panel door and side-plate and check doors are accessible for internal
inspection/maintenance.
Tie-Down
Lifting
Hook