Shindaiwa DGK125F User manual

OWNER’S AND OPERATOR’S MANUAL
Vertical, Water-Cooled 4-Cycle Diesel Engine
DGK125F
X753-008 26 0
X753801-430 0
California Proposition 65
WARNING
Breathing diesel engine exhaust exposes you to chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm.
Always start and operate the engine in a well ventilated area.
If in an enclosed area, vent the exhaust to the outside.
Do not modify or tamper with the exhaust system.
Do not idle the engine except as necessary.
For more information go to www.P65warnings.ca.gov/diesel.
WARNING
Cancer and reproductive Harm-
www.P65Warnings.ca.gov
WARNING
Batteries, battery posts, terminals and related accessories contain lead and lead compounds, and
other chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm. WASH HANDS AFTER HANDLING.
CAUTION
Do not operate the Generator, or any other appliance, before you have read and understood the
instructions for use and keep near for ready use.

Introduction
Thank you for purchasing this Shindaiwa soundproof diesel engine generator.
This manual has been created to ensure safe usage of this generator. Be sure to read this
manual before operation. Improper operation/handling of this generator will result in an
accident or malfunction.
Handling/Operation of this generator can only be performed by persons who understand the
contents of this manual and can handle/operate the generator in a safe manner. Persons who
suffer from an illness, are taking medicine or not feeling well such that safe operation would
be negatively affected must not operate this generator.
Work performed using this generator and handling/operation of this generator must be in
accordance with corresponding laws and regulations based on such laws. Consult with the
authorized distributor where this generator was purchased if you have any inquiries regarding
the corresponding laws.
Always be sure to include this manual when loaning out this generator and instruct operating
personnel to read this manual before operation.
Store this manual in a specified location where it will be secure and available for consulting at
any time. Order another copy from the authorized distributor where this generator was
purchased if this manual becomes dusty, grimy or torn.
Consult with the authorized distributor where this generator was purchased if you have any
inquiries regarding any points related to this generator and manual.
When inquiring about this generator, be sure to provide the model name and serial number.
If disposing of this generator, do so in a manner that is in compliance with laws related to
industrial waste. Contact the authorized distributor where the generator was purchased if you
have any inquiries regarding proper disposal.
■Caution notice ranks in this manual are classified as follows.
Note that CAUTION items can also lead to major accidents under some circumstances
if not correctly followed.
All caution notices are important. Be sure to follow all of them.
WARNING : Indicates a potentially hazardous situation which, if not avoided,
can result in death or serious injury.
CAUTION : Indicates a potentially hazardous situation which, if not avoided,
can result in minor or moderate injury and property damage.
< Note > : Other types of cautions and indications.

1
Table of Contents
1. Safety Instructions ·····························································2
2. Specifications····································································6
2-1. Specifications ································································6
2-2. Ambient Conditions ·························································7
3. Applications ······································································7
4. Part Names········································································7
4-1. External View/Part Names ················································7
4-2. Operation Panel Configuration··········································11
4-3. Output Terminal···························································· 12
4-4. Receptacle Panel ························································· 12
5. Equipment······································································· 13
5-1. Three-phase and Single-phase simultaneous Output············ 13
5-2. Available Output Monitor ················································ 13
5-3. Spill Containment ························································· 14
5-4. Warning Indicators ························································ 15
5-5. SCR (Selective Catalytic Reduction) System and Indicators··· 17
5-6. Meters and Gauges······················································· 20
5-7. Fuel Piping Switch (3Way Fuel Valve) ······························· 24
5-8. Load Bank Control Switch ·············································· 24
6. Transport/Installation························································ 25
6-1. Transport Procedures ···················································· 25
6-2. Installation Procedures ·················································· 25
7. Load Connections ···························································· 26
7-1. Load Cable Selection ···················································· 26
7-2. Connecting Load Cables ················································ 27
8. Pre-Operation Inspection ·················································· 31
8-1. Checking Engine Oil······················································ 31
8-2. Checking Coolant ························································· 32
8-3. Checking the Fan Belt ··················································· 33
8-4. Checking the Fuel························································· 34
8-5. Checking the DEF (Diesel Exhaust Fluid)··························· 34
8-6. Checking the Spill Containment ······································· 35
8-7. Checking for Fuel, Oil and Coolant Leak ···························· 35
8-8. Checking the Battery ····················································· 35
9. Operating Procedures······················································· 37
9-1. Initial Startup/Pre-Check ················································ 37
9-2. 208/240/480V Switching Selection···································· 39
9-3. Procedures during Operation ·········································· 39
9-4. Stopping Operation ······················································· 41
9-5. Protective Functions······················································ 42
9-6. Connecting with External Fuel Tank ·································· 43
10. Inspection/Maintenance··················································· 44
11. Long-Term Storage ························································· 56
12. Troubleshooting ····························································· 57
13. Generator Circuit Diagram ··············································· 60
14. Engine Electrical Circuit Diagram ····································· 61

2
WARNING : EXHAUST GAS POISONING
Do not operate the generator in poorly ventilated areas such as indoors or tunnels, as the
exhaust gas of the engine contains substances that are harmful to human health.
Do not direct exhaust fumes at bystanders or buildings.
WARNING : ELECTRIC SHOCK
Do not operate the equipment with any doors or covers open.
Always turn all the breakers OFF, place the starter switch in the STOP position and stop the
engine before connecting / disconnecting the load cable to the output terminal or
receptacle.
Close the output terminal cover before operating.
Do not insert a pin, wire or other metal object into the electrical outlet.
Do not touch the generator if the generator or casing or your body becomes wet during
operation.
Do not touch internal electric parts while the generator is operating.
Always turn the starter switch to the STOP position and stop the engine, then close and
lock OPERATION PANEL DOOR before checking or maintaining the engine or any
equipment.
WARNING : INJURY
Close all doors and lock them during operation.
Do not open the check door when the starter switch is in the AUTO or START position. It
will cause injury by rotating parts such as cooling fans and fan belt.
Alwaysturn thestarterswitchtotheSTOPposition andstop the engine,thencloseandlock
OPERATION PANEL DOOR before checking or maintaining the engine or any equipment.
Always be sure to use Lifting Hook when lifting up the generator. Using other parts when
lifting up the generator could cause the result of falling.
Do not attempt to lift the equipment with any additional weight such as optional fuel tanks or
trailers.
No persons should ever be under a lifted generator.
Always be sure to check that the breakers on load side and switches for any equipment
using the generator are at OFF before turning the breaker to ON. Also be sure to advise
personnel on the load side that power will be turned on or off before operating the breaker.
Do not modify the equipment and do not operate with parts removed.
CAUTION : EYE/SKIN INJURY
Wear rubber gloves and other protective wear to protect eyes, skin and clothing from the
battery fluid which contains diluted sulfuric acid. If the battery fluid contacts eyes or skin,
wash out immediately with a sufficient amount of clean water. Be sure to receive medical
treatment, especially if the fluid contacts the eyes.
CAUTION : EXPLOSION
Never use or recharge the battery if the fluid level is below the minimum level.
Do not create sparks or bring flame near the battery as it generates flammable gas.
1. Safety Instructions

3
CAUTION : FIRE
Do not carry flammable items (such as fuel, gas and paint) or items that are highly
combustible near the generator as the muffler, exhaust gas and other parts become
extremely hot.
Position this generator 3 ft. (1 m) or more from walls or other hindrances, and on a level
surface.
Do not connect the generator output to indoor wiring.
This generator uses diesel fuel. Always be sure to stop the engine and not bring flames
close when inspecting fuel or refueling. Wait until the engine has cooled before performing
such procedures.
If fuel spills, always be sure to wipe and drain off spilled fuel.
Do not operate the equipment with liquid accumulated in the spill containment.
If fuel or oil is leaking, repair the leaking location before operating.
Always be sure to wipe up any spilled fuel or oil.
Allow the generator to cool before covering with the protective cover.
Never allow flame to come close to the generator.
Always make sure that the engine is stopped when working on piping.
After working on the piping, check that there is no fuel leakage.
Absolutely never inspect or perform maintenance to the equipment near fire or other open
flame.
Do not put anything other than DEF (gasoline, diesel fuel, etc.) in the DEF tank. Also, do
not put DEF diluted with water or other liquids.
CAUTION : ELECTRIC SHOCK
Do not sprinkle water on equipment or used where exposed to rain.
CAUTION : BURNS
Do not touch the engine and surrounding components immediately after stopping the
engine as they are still extremely hot.
Do not open the radiator cap immediately after stopping the engine. Doing so will result in
hot steam gushing out.
Hot steam gushes out from the coolant sub-tank if the generator overheats. Do not touch
the coolant sub-tank.
Always be sure to stop the engine and allow the engine to cool when performing inspection
or maintenance of engine oil. Opening the oil level gauge or oil filler cap during operation
will result in hot oil gushing out.
While the engine is running, the SCR system is purging, and immediately after operating,
the SCR system and exhaust piping is extremely hot. Be careful not to inadvertently touch
them.
Do not touch the SCR system and surrounding components immediately after stopping the
engine as they are still extremely hot.

4
CAUTION : INJURY
Always be sure to use Lifting Hook when lifting up the generator, and slowly lift it straight
up.
Personnel performing lifting work must wear protective gear such as helmets, safety shoes
and gloves.
Position the generator on a level stable surface so that it cannot slide or move in any
manner.
Before starting operation, always be sure to turn off all switches of equipment using the
generator and all breakers to OFF.
Do not move the generator during operation.
Do not operate the generator if it has been modified or any parts have been removed.
Securely fix the equipment with rope or similar item to avoid any unexpected move when
transporting by truck or other vehicle.
CAUTION : PROPERTY DAMAGE
Do not use the equipment for any improper applications. Improper usage can result in an
accident or malfunction.
If using this generator for medical equipment, check before use with the medical equipment
manufacturer, doctor, hospital or similar entity.
Check that the generator output setting, output terminal connection and load power source
are consistent.
Cable burnout can occur due to generated heat if the load current exceeds the allowable
current of the cable.
The voltage drop between cables is large if the cable is excessively long or thin, resulting in
decreased input voltage to equipment using the generator, thereby causing decreased
performance, faulty operation and malfunction.

5
■Warning /Caution Label Locations
If warning or caution labels become damaged and difficult to read, replace with new labels in
the indicated locations. Order labels using part number indicated in the parenthesis.
①
Caution: Do not change voltage
Part no. :X505-004620
②
Warning caution
Part no. :X505-010910
③
Caution: Auto start
Part no. :X505-010800
④
Warning: Proposition 65 Gen
Part no. :X505-010400
⑤
EPA emission complied notice
Part no. :X505-008400
⑥
Warning: Fire
Part no. :X505-007650
⑦
Notice: Capacity of the external tank
Part no. :M709-000370
⑧
Terminal cover instructions
Part no. :M704-002250
⑨
Continuous output
Part no. :M705-001610
⑩
Warning: Electric shock
Part no. :X564-000570
⑪
DEF / AdBlue Complied notice
Part no. :M708-000070
⑫
Warning: Injury
Part no. :X505-007550
⑬
Caution: GM SPEC LLC
Part no. :X505-007840
⑭
Warning: Proposition 65 Battery
Part no. :X505-010410
⑮
Warning: Injury
Part no. :X564-000530
⑯
Caution: Burn
Part no. :X505-007830
Ⓡ
BATTERY

6
2-1. Specifications
Model
Unit
DGK125F
Alternator
Generator Type
-
Revolving Field Brushless
Rated Frequency
Hz
60
Rated Output(Prime)
Three phase
kVA
125
kW
100
Single phase
kVA
75[37.5] *1
kW
75[37.5] *1
Standby Output
Three phase
kVA
137.5
kW
110
Single phase
kVA
82.5 [41.3] *1
kW
82.5 [41.3] *1
Rated Voltage
Three phase
V
208/240/ [480] *1
Single phase
V
120/139/240/[277] *1
Rated Current
Three phase-208V
A
347
Three phase-240V
A
301
Three phase-480V
A
150
Single phase-120V
A
313 × 2 [156 x 2]*1
Single phase-240V
A
313 [156]*1
Power Factor
-
Three phase 0.8, Single phase 1.0
Insulation class
-
F
Excitation
-
Self Excitation (brushless)
No. of Poles
-
4
Engine
Type
-
Vertical Water-Cooled 4-Cycle Diesel
Model(Manufacturer)
-
4HK1X(ISUZU)
No. of Cylinders
(bore × stroke)
(in./mm)
4(4.53x4.92/115x125)
Continuous Rated Output
hp
152.3
Rated Speed
rpm
1,800
Displacement
cu.in./liters
316.9/5.193
Combustion System
-
Direct injection (Turbo-charged)
Cooling Method
-
Water cooled
Starting Method
-
Electric
Fuel
-
No.2-D,S15 EPA regulation
Diesel Exhaust Fluid
ISO 22241 or API standard
Lubricating Oil
-
API service-type CJ-4 class
Fuel Tank Capacity
gal./liters
171.7/650
DEF Tank Capacity
gal./liters
7.4/28
Lubricant Volume
gal./liters
6.2/23.5
Cooling Water Volume
gal./liters
8.2/31
Starting Motor Capacity
V-kW
12-2.5
Charging Alternator
Capacity
V-A
12-110
Battery Capacity
V-Ah
12-120
Unit
Length
in./mm
120/3,050
Width
in./mm
48.8/1,240
Height
in./mm
59.1/1,500
Dry Weight
lbs./kg
6,592/2,990
Net Weight
lbs./kg
8,091/3,670
*1:Output in the brackets shows when the selector switch is set at 480V.
2. Specifications

7
2-2. Ambient Conditions
Use this generator in ambient conditions as described below. Failure to provide these
conditions can result in problems such as malfunction, insufficient output and reduced
durability.
■Ambient temperature: 5 to 104 °F (-15 to 40 °C)
■Relative humidity: 85% or less
■Altitude: 984 ft. (300 m) or less
Power source for submerged pumps and similar civil engineering equipment
Power source for lighting and similar equipment
Power source for electrical tools and household appliances
4-1. External View/Part Names
CAUTION : PROPERTY/SECONDARY DAMAGE
Do not use for any application other than those listed above.
If using this generator for medical equipment, check before use with the medical
equipment manufacturer, doctor, hospital or similar entity.
3. Applications
4. Part Names
Inspection / Cleaning Panel
Spill Containment
Drain Plug
DEF Inlet Cover
Tie hole
Tie Hole
Terminal Cover
Operation Panel Door
Lifting Hook
Radiator Plate
Fuel Drain Plug
Tie Hole
Receptacle Cover
Fuel Inlet Cover

8
Engine
Check Door
Alternator
Check Door
Fan Guard
3way Fuel Valve
Oil Drain Plug
Electromagnetic
Fuel Pump
Fuel Filter
(Pre)
Fuel Filter
(Main)
Oil Filter
External Fuel Inlet
External Fuel Return
Oil Level Gauge
Turbo Charger Cover
SCR Check Panel
Tie Hole
Tie hole
Inspection / Cleaning Panel
DEF Tank
Check Panel
Tie Hole

9
Output Terminal
Terminal Cover
Receptacle Cover
Remote Start Terminal
Receptacle Panel
Fan Guard
Battery
Coolant Sub-Tank
Engine
Check Door
Air Cleaner
Alternator
Check Door
Radiator
Intercooler
Coolant Drain Plug
Fuel Tank
(Inside)
Intercooler Drain Plug

10
Engine
Warranty
Manual
Accessories
Owner’s
and
Operator’s
Manual
Product
Warranty
Manual
DEF Tank Check Panel
Supply Module / Filter
DEF Tank
Muffler
(SCR)
Dosing Module
SCR Check Panel

11
4-2. Operation Panel Configuration
①
Circuit Breaker(3-Phase & 1-Phase)
⑬
Available Output Monitor
②
Voltmeter
⑭
Fuel Level
③
Ammeter
⑮
Fuel Leak Detected Lamp
④
Frequency Meter
⑯
DEF Level
⑤
Pilot Lamp
⑰
Hour Meter
⑥
Voltage Regulator
⑱
Glow Lamp
⑦
Ammeter Selector Switch
⑲
Starter Switch
⑧
Breaker Trip Selector Switch
⑳
Throttle Switch
⑨
Warning Indicators
㉑
Accessory Switch
⑩
SCR Indicators
㉒
Voltage Selector Switch
⑪
Oil Pressure / Water Temperature
/ Speed Monitor
㉓
Load Bank Control Switch
⑫
Oil Pressure / Water Temperature
/ Speed Selector Switch
㉔
Auto start Panel ( Optional )

12
4-3. Output Terminal
4-4. Receptacle Panel
< NOTE >
・All duplex receptacles are GFCI protected and are rated at 20 amps. All twist lock
receptacles are rated at 50 amps.
①
Single-Phase Circuit Breaker (50A)
②
Single-Phase Circuit Breaker (20A)
③
Single-Phase Twist Lock 240/120V Receptacle (50A)
④
Single-Phase GFCI 120V Receptacle (20A)
⑤
Remote Start Terminal
Three-Phase Output Terminals
Single-Phase Output Terminals

13
5-1. Three-phase and Single-phase simultaneous Output
This generator is capable of generating three-phase and single-phase three-wire output
simultaneously. (Three-phase output terminal and single-phase three-wire output terminal are
equipped individually.)
Neither switching operation of output nor switching operation of wiring is needed.
Three-Phase and Single-Phase Three-Wire Output Terminal
< Note >
Refer to section “7-2. Connecting Load Cables” for Load Connections.
If using three-phase output simultaneously with a single-phase three-wire type output, use in
a range where the total current does not exceed the rated current.
5-2. Available Output Monitor
The available generated output for each output power source is displayed digitally.
< Note >
Consider the digitally displayed available output as an
approximate estimate. Be sure to thoroughly consider the
displayed value and the used load capacity when using a load
such as a motor with large starting capacity.
The displayed output capacity might not be correct values if
using a four-wire connection (single-phase using the N
terminal) for a three-phase output power source. Connect to a
single-phase/three-line type power source if using a
single-phase power source.
If “- -” is displayed for the available output, it means that usage
has exceeded the rated capacity. Immediately stop the
equipment being used and reduce the load capacity of the
equipment.
5. Equipment

14
5-3. Spill Containment
The bed of this generator is equipped with the spill containment (structure for preventing
leakage of liquid) so that any spilled liquid will not leak to outside of the generator when oil or
fuel is spilled or leak. Before starting operation, check if there is accumulated liquid in the spill
containment. Flush out any liquid that has accumulated.
(Refer to section “8-6. Checking the Spill Containment” for inspection procedures. )
(Refer to section “10. Inspection/Maintenance (14) Flushing Liquid in Spill Containment”
for flushing procedures.)
The generator is equipped with the following in order to prevent liquid from spilling in case you
forget to flush the liquid: The operation panel is equipped with the SPILL CONTAINMENT
CHECKING indicator that illuminates when its sensor is triggered as the spill containment
capacity accumulated enough liquid to reach to about 25gal. (96 liters).
If the liquid stored in the spill containment exceeds approximately about 41gal. (155 liters)
during operation, the SPILL CONTAINMENT OVERFLOW WARNING indicator illuminates, and
the engine will be automatically stopped. If this occurs, flush the liquid stored in the spill
containment.
(Refer to section “10. Inspection/Maintenance (14) Flushing Liquid in Spill Containment”.)
< Note >
Water can also accumulate in the spill containment due to rain entering into the generator.
Accordingly, you should periodically flush liquid accumulated within the generator. However,
you should flush water according to the frequency/amount of rainfall.
The types of liquids that can accumulate in the spill containment include oil, fuel, coolant,
battery fluid and DEF such that it is not possible to distinguish between rainwater and other
liquids. Dispose of flushed liquids according to the applicable laws and regulations.
WARNING : INJURY
Do not open the check door when the starter switch is in the AUTO or START position.
It will cause injury by rotating parts such as cooling fans and fan belt.
Always turn the starter switch to the STOP position and stop the engine, then close
and lock OPERATION PANEL DOOR before checking or maintaining the engine or
any equipment.
CAUTION : BURNS
Do not touch the engine and surrounding components immediately after stopping the
engine as they are still extremely hot.
CAUTION : FIRE
If fuel or oil is leaking, repair the leaking location before operating.

15
5-4. Warning Indicators
This generator is equipped with the following warning indicators: BATTERY (battery charge),
OIL PRESS (engine oil pressure), WATER TEMP (coolant temperature), OVER SPEED
(engine overspeed), AIR FILTER (air cleaner clogging), SPILL CONTAINMENT (spill
containment amount), OVER CRANK (engine fails to start), and ENGINE (engine malfunction).
When the engine starts, all the lamps will be lights off. An indicator illuminates if a
malfunction/fault occurs during operation and the engine automatically stops depending on the
fault type. Selecting the starter switch from STOP to START position causes the BATTERY
warning indicator to illuminates and ENGINE for warning indicator to illuminates approximately
3 sec.
(1) BATTERY (Battery Charge) Warning Indicator (Low Battery Voltage)
The BATTERY warning indicator illuminates when charging is not possible during operation. If
this occurs, contact authorized distributor where the generator was purchased.
< Note >
This battery charging warning indicator cannot detect battery deterioration or insufficient
battery fluid. (Refer to section “8-8. Checking the Battery”.)
(2) OIL PRESS (Engine Oil Pressure) Warning Indicator (Low Oil Press.)
If the engine oil pressure drops below 7 psi (0.48 x100 kPa) during operation, the OIL PRESS
warning indicators illuminates, and the engine will be automatically stopped.If this occurs,
check the engine oil level and add engine oil until it reaches the maximum level.
< Note >
This oil pressure warning indicator cannot detect oil deterioration. Change the engine oil
periodically. (Refer to section “8-1. Checking Engine Oil”.)
WARNING : INJURY
Do not open the check door when the starter switch is in the AUTO or START position.
It will cause injury by rotating parts such as cooling fans and fan belt.
Always turn the starter switch to the STOP position and stop the engine, then close
and lock OPERATION PANEL DOOR before checking or maintaining the engine or
any equipment.
CAUTION : BURNS
Do not touch the engine and surrounding components immediately after stopping the
engine as they are still extremely hot.
CAUTION: BURNS
Always be sure to stop the engine and allow the engine to cool when performing
inspection or maintenance of engine oil. Opening the oil gauge or oil filler cap during
operation will result in hot oil gushing out.

16
(3) WATER TEMP (Coolant Temperature) Warning Indicator (High Water Temp.)
If the coolant temperature rises above 212°F(100℃) during operation, the WATER TEMP
warning indicators illuminates, and the engine will be automatically stopped. If this occurs, hot
steam will gush out of the coolant sub-tank. Check the coolant sub-tank coolant level after the
generator cools and add coolant to the coolant sub-tank if it is insufficient. (Refer to section “8-2.
Checking Coolant”.) If the coolant is at the specified amount, it is probable that the fan belt is
loose or there is a coolant leak. Wait for the engine to cool down and inspect for these
problems.
< Note >
The coolant temperature cannot be detected if the coolant level is excessively low. Always be
sure to check the coolant level in the radiator coolant sub-tank before starting operation.
(4) OVER SPEED (Engine Over Speed) Warning Indicator
This generator is equipped with a function such that the engine is automatically stopped if an
engine fault occurs causing the engine speed to increase excessively. If the engine speed rose
above 2,070rpm during operation, the OVER SPEED warning indicators and ENGINE warning
indicators illuminates, and the engine will be automatically stopped. If this occurs, it is probable
that some malfunction has occurred in the engine. Contact authorized engine distributor or
manufacture for repair options.
(5) AIR FILTER (Air Cleaner Clogging) Warning Indicator
The AIR FILTER warning indicator illuminates if the air cleaner element becomes clogged
during operation. If it illuminates, immediately stop the engine and clean or replace the air
cleaner element.
(Refer to section “10. Inspection/Maintenance (3) Air Filter Element Cleaning/Replacement”.)
(6) SPILL CONTAINMENT (Spill Containment Amount) Checking Indicator
The SPILL CONTAINMENT checking indicator illuminates if the liquid
stored in the spill containment exceeds approximately about 25 gal.
(96 liters) during operation. If it illuminates, immediately stop the
engine and flush the liquid stored in the spill containment.
(Refer to section “10. Inspection/Maintenance (14) Flushing Liquid
in Spill Containment”.)
< Note >
The engine may not be stopped only if the spill containment checking Indicator illuminates
during operation.
When the spill containment checking Indicator illuminates during operation, stop the engine,
check for fuel, oil, cooling water and DEF leakage, and repair as necessary.
Do not use the equipment with liquid accumulated in the spill containment. Drain the spill
containment before using.
CAUTION: BURNS
Do not open the radiator cap immediately after stopping the engine.Do so will result in
hot steam gushing out.
Hot steam gushes out from the coolant sub-tank if the generator overheats. Do not
touch the coolant sub-tank.
SPILL CONTAINMENT
Checking Indicator

17
(7) SPILL CONTAINMENT (Spill Containment Amount) Overflow Warning Indicator
If the liquid stored in the spill containment exceeds approximately
about 41 gal. (155 liters) during operation, the SPILL
CONTAINMENT overflow warning indicator illuminates, and the
engine automatically stops. If this occurs, flush the liquid stored in
the spill containment.
(Refer to section “10. Inspection/Maintenance (14) Flushing
Liquid in Spill Containment”.)
< Note >
Although the fluids that can leak internally consist of oil, fuel, cooling water and DEF, the spill
containment does not have a function that can separate rainwater that has leaked into the
equipment from these internally leaked fluids. Properly dispose of liquid drained from the spill
containment in a manner according to the applicable laws and regulations.
(8) Over Crank / No Speed Signal Indicator
This indicator illuminates if the engine fails to start. If that happens, set the "STARTER
SWITCH" selector to STOP, and inspect the machine. (Refer to section "12. Troubleshooting.")
If this indicator starts flashing, the rotation signal has not been detected correctly. Contact the
authorized distributor where the generator was purchased.
(9) ENGINE (Engine Malfunction) Warning Indicator
The ENGINE warning indicator illuminates if the coolant temperature is high, the oil pressure is
low, the engine overspeeds, the battery voltage is low or some other engine fault occurs during
operation. If this occurs, a malfunction code is displayed on the engine and available output
monitors, and the engine automatically stops or the engine output is reduced.
If the ENGINE warning indicator illuminates, contact the authorized distributor where the
generator was purchased.
5-5. SCR (Selective Catalytic Reduction) System and Indicators
In order to meet requirements set forth by EPA Tier4 (Final), the SCR system is equipped to
reduce nitrogen oxides (NOx) in exhaust emissions, and Diesel Exhaust Fluid (DEF) is used as
a reducing agent.
WARNING : INJURY
Do not open the check door when the starter switch is in the AUTO or START position.
It will cause injury by rotating parts such as cooling fans and fan belt.
Always turn the starter switch to the STOP position and stop the engine, then close
and lock OPERATION PANEL DOOR before checking or maintaining the engine or
any equipment.
CAUTION : BURNS
Do not touch the engine and surrounding components immediately after stopping the
engine as they are still extremely hot.
While the engine is running, the SCR system is purging, and immediately after
operating, the SCR system and exhaust piping is extremely hot. Be careful not to
inadvertently touch them.
SPILL CONTAINMENT
Overflow Warning Indicator