Shintaro SHUSB3PCIE User manual
USB 3.0 PCI-e Card
User Manual
shintaro.com.au
SHUSB3PCIE
Copyright Information 4
Precaution 5
General Information 6
Product Layout 7
Hardware Installation 8
Driver Installation 9
Product Specications 11
USB 3.0 PCI-e Card
Contents
shintaro.com.au
4
Copyright Notice
This document is copyrighted. The information provided in this document has been
carefully checked for accuracy at the time of publication. No representations or
warranties, either expressed or implied, with respect to the contents hereof and
specically disclaims any warranties, merchantability or tness for any particular
purpose.
Any software described in this manual is sold or licensed “as is”. Should the programs
prove defective following their purchase, the buyer assumes the entire cost of all
necessary servicing, repair, and any incidental or consequential damages resulting from
any defect in the software.
The manufacturer reserves the right to revise this publication and to make changes
from time to time in the contents hereof without obligation to notify any person of such
revision or changes.
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form of or via any means without the prior written permission of the
manufacturer.
Trademark Acknowledgement
All brand, company and product names used for identication in this document are
trademarks or registered trademarks of their respective companies.
© Copyright 2009, Version 1.0
All rights reserved.
Printed in Taiwan
5
Important Precaution
Before getting started, read these instructions and save them for later reference.
1. Before connecting the Express card to the laptop, read through this user’s guide. In
some operating systems, the drive software must be installed prior to operation.
2. Do not insert with strong force, as doing so may severely damage the product.
3. Be careful not to injure yourself by catching your ngers when loading the
SHUSB3PCIE or USB devices.
4. Do not disassemble or modify the product in any way. Disassembly or modication
may not only void warranty but could cause damage or lead to le or electric shock.
5. Do not use or store the product in damp locations or under high temperature.
6. Liquid entering the product also may cause damage or lead to le or electric shock.
6
General Information
Thank you for purchasing SHUSB3PCIE 2 ports USB3.0 PCI Express adapter. Super-
Speed USB3.0 interface provides a reliable solution for PCs, consumer electronics and
communications devices.
SHUSB3PCIE is a dual-port USB3.0 PCI Express adapter, and it can transfer data up
to 5.0Gbps when connecting to USB 3.0 compliant peripherals, or with existing USB
peripheral devices. It also supports backward compatible with USB2.0 High-Speed and
USB1.1 Full-Speed device. It is an ideal technology for external storage devices, digital
cameras, webcams, scanners, and many more.
Key Features
Compliant spec. to USB3.0 Rev. 1.0.•
Compliant spec. to Intel xHCI Rev 0.96•
Compliant spec. to PCI Express 2.0 interface.•
Compliant spec. to PCI Express Generation 2 spec.•
Support Super-Speed data transfer rate up to 5.0Gbps.•
Provide USB3.0 interface compatible with prior ubiquitous USB2.0 standard.•
More power at the connector, Max. 900mA.•
Built-in 4-pin power connector for receiving extra power supply from system.•
Support standard PCI Express slot.•
Support hot swapping and Plug-and Play capability.•
System Requirements
A PC mainboard with a PCI Express slot
7
Package Contents
USB PCIe Card
Low prole bracket
Driver Disk
Product Layout
Below is a sample picture describing the general location of external USB3.0 ports.
However, minor differences will occur, depending on the model.
8
Hardware Installation
Warning:
Touch the exposed metal casing on your computer’s power supply before you•
taking the card from its antistatic package. This safely discharges any static
electricity that may have built up on your body.
Handle the card by the PCB edge only. Avoid touching the gold-plated bus or any•
electronic components.
Turn your computer off and disconnect the power cord before installing the host card.1.
Remove your computer’s cover. (Please refer to your computer owners manual for2.
instructions on removing the cover)
Locate an available PCI Express expansion slot and3.
remove the bracket cover.
Insert the card carefully into a free PCI Express slot and4.
make sure the gold-plated bus is seated evenly in the
PCI Express slot.
Fasten the PCI Express card’s mounting bracket5.
securely to the rear computer case by screw, to avoid
it accidentally falling out when plugging in the external
USB device.
Connect 4P power cable from the power supply to SHUSB3PCIE.6.
Before replacing your computer’s cover, you must make sure no tools or screws are7.
left inside your computer case.
Reconnect AC power cord and turn the power on, to complete the driver software8.
installation.
9
Driver Installation
Before you start to use SHUSB3PCIE, please install the driver rst (Windows XP/VISTA/7)
1. Insert program disc into the CD-ROM/DVD-ROM drive.
2. Click SHUSB3PCIE 4. Click Next to go on
3. Click Windows Driver to install 5. Select “I accept the terms of the license
agreement” and click Next begin install
10
1. Click Next to continue 3. Click Finish to complete the process
2. Click Install to begin the installation 4. And you can nd USB3.0 Host Controller
in device management
11
Product Specifications
Specifications
USB3.0 Host Controller NEC uPD720200
Max. Data Transfer Rate 5.0Gbps
I/F to PC PCI Express2.0 x 1
External Port 2 USB ports (Support Super-Speed/
High-Speed/Full-Speed/Low-Speed)
Power Input 4-pin power connector
Power Output DC +5V/ Max. 900mA
System Support Windows XP / VISTA / 7 (32/64bit)
Dimension 80 x 68.5 x 1.6 mm (L x W x H)
Operating Temperature 0°C~40°C
Storage Temperature -20°C~60°C
Operating Humidity 0%~80% RH, non-condensing
Certication FCC Class B, CE
* Specications are subject to revision or update without notice
12
support@shintaro.com.au
Table of contents
