Shinybow USA SB-6230T User manual

SB-6230R or SB-6230T
CAT5/Component Video - RGB/YPbPr/HDTV
REPEATER+RECEIVER or TRANSMITTER
SB-6230R
SB-6230T
INSTRUCTION MANUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before
operating your equipment. Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing
in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected
from rain, water and excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust
with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so
that they are not likely to be walked on or pinched by items placed upon or against them, paying particular
attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to
be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions
should be taken so that the means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection
to improper AC voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust,
moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing
devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment
which may impede the normal ow of air around the unit, such as a bed, rug, carpet, or completely enclosed
rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown
free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside.
Refer all servicing to qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the
interconnecting cables to other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever
need to ship the unit, use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED
BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

1
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting
the power supply. Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of re, electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may
damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk
on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide
ventilation and allow for sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. We assume no
responsibility for any infringements of patents or other rights of third parties which may result from its use.
We assume no responsibility for any inaccuracies that may be contained in this document. We make no
commitment to update or to keep current the information contained in this document.
We reserve the right to make improvements to this document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of
its part translated into any language or computer le, in any form or by any means — electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise — without the express written permission and consent.
© Copyright 2020. All Rights Reserved.
Version 2.2 APR 2020
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they
are associated.
www.shinybowusa.com
122 Rose Ln. Suite 303 | Frisco, Texas 75036
[email protected]

2
INTRODUCTION / FEATURES ..........................................................................................2
SPECIFICATIONS / CONTENTS .......................................................................................3
TYPICAL HOOKUP & OPERATION .................................................................................4
INTRODUCTION
CAT5 Transmitter/Repeater/Receiver Series
Thank you for purchasing the YUV CAT5 SB-6230T Transmitter or SB-6230R Receiver.
You will nd these units easy to install and highly reliable but it is essential that you read
this manual thoroughly before attempting to use these extenders.
Congratulations on your purchase of one the most innovative CAT5 Transmitter/Repeater/
Receiver products on the market today. These video splitter extenders consist of (2) units.
The SB-6230T (2) port transmitter unit connects to your local component video source
and allows you to split and extend (2) remote monitors. Driving high performance HDTV
Component Video (YPBPR) 480p-720p-1080i-1080p digital signals over long distances via
a category cable to the SB-6230R receiver. These CAT5 component video splitter extender
via CAT5 is the ideal solution for applications to display the same image on multiple remote
locations. Terminated for a RJ-45 (Category 5) and VGA HD-15, earphone connectors.
These AV splitter extenders are commonly used at restaurants, bars, clubs and other
HDTV environments for video broadcasting such as remote monitoring, presentations and
advertising.
FEATURES
• SB-6230T TRANSMITTER
• Input: (1) Component Video (YPBPR)
• Output: (2) CAT5 (Tx) Distribution
• SB-6230R RECEIVER
• Input: (1) CAT5 (Rx) Receiver / (1) CAT5 (Tx) Repeater
• Output: Component Video (YPBPR)
• Receiver includes (1) RJ-45 Input with (1) RJ-45 Looping Output
• Transmitter includes (2) RJ-45 output sockets
• Inputs via gold plated, color coded RCA Phono sockets on the Transmitter
• Outputs via gold plated, color coded RCA Phono sockets on the Receiver
• Category UTP cable max length up to 1000 feet
• Easy to install and highly reliable
• Brushed aluminum case with mounting brackets
• LED power ON indicator
• Includes power supply
• Supports resolutions up to 1080p
• Transmitter can connect to (2) separate CAT5 receivers
• Receiver provides Tint and Brightness control
TABLE OF CONTENTS

3
SPECIFICATIONS / PACKAGE CONTENTS
SPECIFICATIONS
• Model Number: SB-6230T (Tx), SB-6230R (Rx)
• Tx/Rx Inputs/Outputs:
• Tx Input: (1) Component Video (YPBPR)
• Tx Outputs: (2) CAT5 (Tx) Distribution
• Rx Inputs: (1) CAT5 (Rx) Receiver / (1) CAT5 (Tx) Repeater
• Rx Output: Component Video (YPBPR)
• Type of Signals: Component Video (YPBPR)
• Cable for CAT5/5e:
• YUV Resolutions:
• 1080i (1920x1080) 450 ft
• 720p (1080x720) 600 ft
• 480p (720x480) 1000 ft
• Video Bandwidth:
• Tx: 400MHz, 13dB full power
• Rx: 270MHz 1090V/us@G=+1
• Tx Slew Rate: 2000V/us
• Video Maximum Input Levels: 1.45Vpp
• Rx High input Impedance: 1MΩ differential
• Audio Frequency Response: 20Hz to 20KHz, +/-1dB
• Audio Maximum Input Levels: 3.1Vpp (line level)
• Low Distortion:
• Tx: 68dB SFDR@5MHz 200Ω load
• Rx: 1Vpp@5MHz
• In/Out Terminal: RJ-45 jack, HD-15 and ear phone jack female connectors
• Housing: Aluminum
• Dimensions (LxWxH): 2.75 x 3 x 1 in
• Weight: 0.4 lb (Unit only) / 0.9 lb (Net)
• Power Consumed: @100mA
• Power Supply: DC 12V@420mA
As product improvements are continuous, specications are subject to change without
notice.
PACKAGE CONTENTS
Check that you have the following components;
• SB-6230 Transmitter or Repeater or Receiver
• Surface Mounting Bracket
• AC/DC Adapter: 12VDC@420mA AC/DC Adaptor Types: CE/UL/SAA/BS
• Users Guide

4
TYPICAL HOOKUP AND OPERATION
SB-6230T
TRANSMITTER
Front:
Input: Component Video (YPBPR)
Rear:
Output: (2) CAT5 (Tx) Transmitter
Power Output: DC12V@420mA
SB-6230R
RECEIVER
Front:
Input: (1) CAT5 (Rx) Receiver
Output: (1) CAT5 (Tx) Repeater (Loop out)
Power Output: DC12V@420mA
Rear:
Output: Component Video (YPBPR)
Component Video Transmitter Signals: 480p(720x480), 720p(1080x720), 1080i(1920x1080)
Safeguards and Precautions
A. Keep this unit away from re, extremely hot areas, water or moisture of any kind.
B. Do not place this unit on any support that is not rm, level and strong.
C. Do not service the unit yourself. Opening the unit’s housing will void the warranty.
D. Servicing must be by Shinybow or by an authorized technician.
C. Illegal duplication of copyrighted material is strictly prohibited by Federal Laws.
Input: Component Video (YPBPR)
Power Input: SB-6230T +12V DC@420mA
SB-6230R +12V DC@420mA

5
TYPICAL HOOKUP AND OPERATION
CAT5 COMPONENT EXTENDER APPLICATIONS TX: Video line driver, Digital line driver, low power differential ADC driver, Signal-ended input to differential output driver RX: High speed differential line receivers, Differential-to-single ended converters, High speed instrumentation amps, level shifting.

LIMITED WARRANTY
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND
SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using or installing the product,
you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the product
and return the product to SHINYBOWUSA, Inc. at the return address set forth on the product’s packing label at your expense. SHINYBOWUSA, Inc.
may modify these Terms and Conditions at anytime, without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to
the product. You are authorized to use the product solely in connection with such instructions. Any use of the product not in accordance with such
instructions shall void any warranty pertaining to the product. Any and all damages that may occur in the use of the product that is not strictly in
accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any
such damage.
The product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to
the product are licensed to you by SHINYBOWUSA, Inc. and/or its afliates, including any manufacturers or distributors of the product (collectively,
“SHINYBOWUSA”) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect
to the product.
The product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use
only. SHINYBOWUSA does not transfer either the title or the intellectual property rights to the product and SHINYBOWUSA retains full and complete
title to the intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the product,
and you may not copy or use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole
discretion of SHINYBOWUSA.
The functionality and usability of the product is controlled by SHINYBOWUSA, Inc. from its ofces within the State of Texas, United States of America.
SHINYBOWUSA makes no representation that materials pertaining to the product are appropriate or available for use in other locations other than the
shipping address you provided with respect thereto. You are advised that the product may be subject to U.S. export controls.
DISCLAIMERS AND LIMITATION OF LIABILITY
SHINYBOWUSA may change or modify the product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT
WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS,
ACCURACY, RELIABILITY, OR OTHERWISE.
SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the product and, therefore, such information or statements
should not be relied upon as being current as of the date you use the product. Moreover, any portion of the materials pertaining to the product may
include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NON-INFRINGEMENT. SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION
WITH RESPECT TO THE PRODUCT. SHINYBOWUSA DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE
ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO
ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY
DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU
OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND
CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY SHINYBOWUSA.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL
OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS
SPECIFICATIONS, EVEN IF SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
IN NO EVENT SHALL SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN
CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT