Shinybow USA SB-6335R User manual

SB-6335R & SB-6335T
HDMI HDBaseT™RECEIVER & TRANSMITTER KIT
up to 330 Ft (100M) (2-way IR, RS-232, HDMI)
INSTRUCTION MANUAL
Receiver
Transmitter

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

CONTENTS
TABLE OF CONTENTS ....................................................1
PACKAGE CONTENTS .................................................. 2
FEATURES ......................................................................3
SPECIFICATIONS ........................................................... 4
TYPICAL HOOKUP & OPERATION ................................ 5
IR EXTENDER ............................................................... 8
RACK MOUNT ............................................................... 10
INTRODUCTION
Congratulations on your purchase of one of the most innovative
HDMI 1.4a over a single category cable Transmitter & Receiver
with RS-232 on the market today. The SB-6335T HDBaseT™
Transmitter can transmit the HDMI signal, IR Remote input or
output signals and RS-232 I/O series interface to the HDBaseT™
Receiver (SB-6335R) via a single category LAN cable for long
distances of up to 328 feet (100M) maximum. These Transmitter
& Receiver units use a single CAT6, CAT6a or CAT7 (UTP/FTP)
category cable via a RJ-45 8P8C female socket. The LAN cable
supports the 568a or 568b LAN color specication table. This
product provides higher full HD HDMI 1.4a, HDTV resolutions
of 480i/p, 720p,1080i/p or high 4K2K quality that are identical to
the source high quality full HDMI 1.4 signals. The Transmitter &
Receiver are useful for sending HDMI digital video & digital multi-
channel audio format signals, IR remote in or out, RS-232 series
in and out control with a single category cable to the HDBaseT™
Transmitter & Receiver.
1
HDBaseT™with Ethernet 100M EXTENDER Series
Thank you for purchasing the SB-6335T & R HDBaseT™ with RS-232 Transmitter & Receiver. You will nd this unit easy to
install and highly reliable but it is essential that you read this manual thoroughly before attempting to use these extenders.
TABLE OF CONTENTS
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update
or to keep current the information contained in this document.
We reserve the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise — without express written permission and consent
© Copyright 2017. All Rights Reserved.
Version 2.3 SEPT 2017
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
CONFORMANCE TEST REPORT
FOR EN 61000-6-1 / EN 61000-6-3
REPORT NUMBER: 09-07-MAS-282-18-R
FOR FCC 47 CFR/Part 15 Subpart B
REPORT NUMBER: 09-07-MAS-282-19-R
Model Number: SB-6335T / SB-6335R
Comment Number: SB-6215, SB-6215R, SB-6215RE, SB-6220R SB-6220RE,
SB-6240R, SB-6240RE, SB-6335, SB-6335R, SB-6320, SB-6320R
RECEIVER:
Input: HDBaseT™CAT6/6a/7 single cable
Output: HDMI & RS-232 series interface
Power Input: +DC12V , 2A
TRANSMITTER:
Input: HDMI ((with DVI -Audio)
Output: HDBaseT™via CAT6/6a/7 Cable
Power Input: +DC12V, 2A

RECEIVER
Check that you have the following components;
• SB-6335R HDBaseT™Receiver console
• (2) SB-100C IR Receiver w/ attached cable
• (2) SB-101C IR Emitter w/ attached cable
• (2) SB-100 IR Receiver w/ assembly plug
• (2) SB-101 IR Emitter w/ assembly plug
• (2) 1 inch High Wall mount pack (Part # WM-1INCH-L80MM)
• Users Guide
• (2) AC/DC Adapter: 12VDC/2A (universal power switch 50/60Hz, 100~240VAC)
TRANSMITTER
Check that you have the following components;
• SB-6335T HDBaseT™Transmitter console
• Users Guide
• AC/DC Adapter: 12VDC/2A (universal power switch 50/60Hz, 100~240VAC)
OPTIONAL ACCESSORIES
• 1x SB-100 set (IR Receiver Extender assy plug)
• 1x SB-100C cable (IR Receiver Cable)
• 1x SB-101 set (IR Transmitter Extender assy plug)
• 1x SB-101C cable (IR Transmitter Cable)
• 1x 1 inch High Wall mount pack (Part # WM-1INCH-L80MM)
• 1x CAT6 Category cable distance 328 feet (100 M), (P/N: UTP6-100)
2
PACKAGE CONTENTS

RECEIVER
• HDBaseT™HDMI Receiver over a single CAT6/6a/7 category LAN cable
• Extends HDMI, IR in/out, RS-232 in/out and Ethernet ports, HDCP compliant
• Uses CAT6, CAT6a and CAT7 UTP/FTP category cable
• Supports link speeds of up to 3.4 Gbps
• Supports Digital RGB 36bits, V1.4a HDMI TMDS format
• Extends higher quality DVI video 1920x1200 resolution
• Supports HD High Denition full range resolution 480p, 720p 1080i/1080p
• Supports long distances up to 328 feet/100M between HDBaseT™Transmitter and HDBaseT™Receiver
• Supports wall mount pack and rack mount installation for 19 inch 4U rack mount
• Power supports DC input with low power consumption (Full load 850mA)
• Power supply using universal power switch 50/60Hz,100~240VAC
TRANSMITTER
• HDBaseT™Transmitter extends the HDMI over single CAT5e/6/6a category 328 feet /100M LAN cable
• Transmits HDMI, IR in/out and RS-232 I/O series interface signals
• Uses a single CAT6, CAT6a and CAT7 (UTP or FTP) category cable
• Supports link speeds of up to 3.4 Gbps, HDMI 1.4, full HD 4K2K signal, HDCP compliant
• Supports Digital RGB 36bits, HDMI digital video TMDS, digital multi-channel audio format
• Extends higher quality full HD DVI video WUXGA 1920x1200 resolution
• Supports High Denition worldwide range resolution 480p, 720p 1080i/1080p-60Hz and 4K2K
• Extends long distances up to 328 feet (100M) between HDBaseT™Transmitter and Receiver
• Supports wall mount installation- total 10 pcs. into one 19 inch 4U rack mount
• Power input via DC with low power consumption (Full load 750mA)
• Power supply using universal power switch 50/60Hz,100~240VAC
3
FEATURES

RECEIVER
• Type of Extender: HDBaseT™Receiver for HDMI signal over one category LAN Cable
• Input Signals: HDMI with Digital Video (TMDS)/Audio 0.5~1.0Vpp, DDC 5Vpp
• HDBaseT™Supports: HDMI Standard, DVI and HDCP Compliant
• Video Support: HDMI and DVI TMDS format for 1920x1200 resolution up to 3.4 Gbps Digital RGB 36bits deep color, 3D 1.4a HDMI format
• HDMI Audio Out Supports: Multi-channel Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus,
DTS, DTS-ES 6.1, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• RS-232 Series Support: 1x RS-232 series interface port (Terminal Block 3pin female socket)
• Category Cable Support: CAT6, CAT6a, CAT7 UTP/FTP cable
• Support HDMI Resolution: 480p, 720p, 1080i/1080p, 4K2K
• Scan Rate Accepted: Supports HDMI full HD resolutions; Frequency 24Hz to 60Hz
• Control: 1x IR in/out, 1x IR in/out, 1x RS-232 and 1x LAN series interface
• IR Infrared Frequency: 38Khz
• Extend Distance: Up to 100M (CAT6)
• Safety Approvals: CE, FCC, VCCI, REACH & WEEE
• Dimensions (LxWxH): 3.15 x 5.12 x 1 in (80x130x26mm)
• Rack Mount: Use total 10 pcs installation into one 19 inch rack mount
• Shipping Weight: 0.325 kgs / 0.715 lb
• Power Consumption: Max 750mA (Full load 1080p-60Hz signal with use DC12V input)
• Power Supply: Power Input +12VDC, 2A, (Universal Type 50/60Hz, 100~240 VAC)
TRANSMITTER
• Type of Extender: HDBaseT™Transmitter for HDMI over single category 328 feet /100M Cable
• Input Signals: HDMI with Digital Video(TMDS)/Audio 0.5~1.0vPP, DDC 5Vpp
• HDBaseT™Supports: HDMI 1.4 Standard, DVI and HDCP Compliant
• Video Support: HDMI and DVI TMDS format for 1920x1200 resolution up to 3.4 Gbps Digital RGB 36bits deep color, 3D 1.4a HDMI format
• Audio I/O Support: Multi-channel Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-
ES 6.1, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
• Extend Distance: Up to 328 feet (100M) via (UTP or FTP CAT6 100M cable)
• Cable Support: CAT6, CAT6a, CAT7 use UTP or FTP category cable
• Supports HDMI Resolutions: 480p, 720p 1080i/1080p@60Hz or 4K2K@24Hz
• Scan Rate Accepted: Supports HDMI full HD Resolutions; Frequency 24Hz to 60Hz
• Control: 1x IR in, 1x IR out and 1x RS-232 I/O series interface
• IR Infrared Frequency: 38Khz
• Safety Approvals: CE, FCC, VCCI, REACH & WEEE
• Dimensions (LxWxH): 5.12 x 3.14 x 1.14 in (130x80x29mm)
• Wall Mount: Wall mount pack (p/n: VM-1inch-L80MM)
• Rack Mount: Total 10 pcs install into 19 inch 4U rack mount
• Shipping Weight: 0.375 kgs / 0.825 lb
• Power Consumption: Max. 750mA (Full load 1080p-60Hz signal with use DC12V input)
• Power Supply: Power Input +12VDC, 2A, (Universal Type 50/60Hz, 100~240 VAC)
As product improvements are continuous, specications are subject to change and without notice.
4
SPECIFICATIONS

5
TYPICAL HOOKUP AND OPERATION
SB-6335R RECEIVER
RECEIVER FRONT:
1. STATUS VIA LED SHOW OUT : POWER, LINK & HDCP
RECEIVER BACK:
5. DC INPUT : DC12V, 2A
6. IR IN : Sends IR signal to HDBaseT™Transmitter
7. IR OUT : Receives IR signal from HDBaseT™Transmitter via IR External Receiver SB-100)
8. RJ-45 IN : HDBaseT™input , Signal from the HDBaseT™Transmitter
9. HDMI OUT : HDMI output, Signal to HDMI destination display device
10. RS-232 I/O : RS-232 series interface in or out control via a PC
Safeguards and Precautions
A. Keep this unit away from re, extremely hot areas, water or moisture of any kind.
B. Do not place this unit on any support that is not rm, level and strong.
C. Do not service the unit yourself. Opening the unit’s housing will void the warranty.
D. Servicing must be by Shinybow or by an authorized technician.
C. Illegal duplication of copyrighted material is strictly prohibited by Federal Laws.

6
TYPICAL HOOKUP AND OPERATION
SB-6335T TRANSMITTER
TRANSMITTER FRONT:
1. STATUS VIA LED SHOW OUT : POWER, LINK & HDCP
TRANSMITTER BACK:
5. DC INPUT : DC12V, 2A
6. IR IN : Sends IR Signal to HDBaseT™Receiver
7. IR OUT : Receives IR signal from HDBaseT™Receiver
8. RJ-45 OUT : HDBaseT™signal output to HDBaseT™Receiver
9. HDMI IN : HDMI signal input from HDMI source device
10. RS-232 I/O : RS-232 I/O series interface via HDBaseT™
Safeguards and Precautions
A. Keep this unit away from re, extremely hot areas, water or moisture of any kind.
B. Do not place this unit on any support that is not rm, level and strong.
C. Do not service the unit yourself. Opening the unit’s housing will void the warranty.
D. Servicing must be by Shinybow or by an authorized technician.
C. Illegal duplication of copyrighted material is strictly prohibited by Federal Laws.

7
INSTALLING DIAGRAM
TYPICAL HOOKUP AND OPERATION

Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug).
Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
SB-100 IR Receiver Set
IR Receiver cable 6ft (2M)
SB-100C IR Receiver Cable
1. SB-100 IR 300M Receiver
Switcher IR EXT. In Cable (3C) IR Receiver (SB-100)
2. SB-100C IR 2M Receiver Switcher IR EXT. In Cable (2C) IR Receiver (SB-100C)
Pin configuration for IR 984 feet (300M) Extender Receiver such as SB-100 compatible
VCC (Ring)
Signal (center)
GND (Sleeve)
Tip Ring
Sleeve
Tip: Signal
Ring :VCC
Sleeve: GND
Ring
Tip (center)
Sleeve
SB-100 IR Receiver Set
Pin configuration for IR Receiver 6 feet (2M) cable such as SB-100C compatible
IR Receiver cable 6ft (2M)
SB-100C IR Receiver Cable
Signal (center)
GND (Sleeve)
Tip Ring
Sleeve
Tip: Signal
Ring: NC
Sleeve: GND
Ring
Tip (center)
Sleeve
The SB-100 IR Receiver is required when using the port “ALL in” Jack.
The SB-100C IR Receiver will not function on the port “ALL in” Jack.
SB-100C Maximum Distance ~ 6 feet (2M)
IN P UT
DC 1 2V
R o H S /95/E C
IR EXT .
RS -232
RS-232 IR E X T. in
ANI-100
IR Rx
POWER
INPUT-1
1234
1 2 34
1234
1 2 3 4
HDMI MAT RIX S W IT CHER
ONOFF
INP UT- 2
INP UT-3
INP UT-4
SWIR
Distance: Max.(2M)
IR PN#: SB-XXXX
Control Switch SB-XXXX
IN P UT
DC 1 2V
R o H S /9 5 /E C
IR EXT .
RS -232
RS-232 IR E X T. in
ANI-100
IR Rx
POWER
INPU T -1
1 2 3 4
1234
1 2 3 4
1234
HDMI MATRIX SW IT CH E R
ON OFF
INPUT- 2
INPUT - 3
INPUT-4
SW IR
Distance: Max.300M
IR PN#: SB-XXXX
Control Switch SB-XXXX
SB-100 Maximum Distance ~ 984 feet (300M)
SB-100 Receiver and SB-101 Transmitter The DISTANCE maximum ~ 984 feet (300M)
SB-100 Receiver and SB-101C Transmitter The DISTANCE maximum ~ 984 feet (300M)
IR EXTENDER
The frequency range of the IR emitter and receivers is 38khz.
8
IR EXTENDER